Anchor AN-130 Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

TROUBLESHOOTING GUIDE
v
o
l
u
m
e
b
a
s
s
t
r
e
b
l
e
ANCHOR Audio, Inc. (310) 784-2300
100-0126-000 / Rev. A - 08/03
Having trouble with the sound system?
Condition Possible Solution
No sound (power LED not lit): turn POWER switch on
plug in power cord
No sound (power LED lights): check for output from source
make sure all cables are completely plugged in
increase volume control
press mute button on remote (AN-130RC only)
turn power switch to off then back to on
(AN-130RC only)
Distorted sound: check input cable connection
lower input signal level
Excessive hum or noise: use shielded input cable
Having trouble with the wireless system?
Condition Possible Solution
No sound: confirm transmitter power switch is set to on
turn up volume control
plug microphone into body-pack transmitter
•turn sound system on
replace mic/transmitter battery
make sure collar, headband or lapel mic cable is
fully plugged into transmitter
turn off mute by pressing, volume up,
volume down or mute (AN-130RC only)
Frequent transmitter dropouts: replace mic/transmitter battery
move mic/transmitter closer to AN-130
change transmitter to different channel
AN-130
AN-130DC
AN-130RC
AN-130U1
Owner’s Manual
13
IMPORTANT SAFEGUARDS SPECIFICATIONS
CAUTION: To reduce the risk of electric shock, do not remove the cover. No user-serviceable
parts inside. Refer servicing to qualified personnel.
WARNING: To prevent fire or electric shock, do not expose this equipment to rain or
moisture.
CAUTION: To reduce the risk of fire, replace only with same type fuse (see specifications).
ATTENTION: Pour eviter les risques de choc électrique, ne pas enlever le couvercle. Aucun
entretien de pièces intérieures par l'usager. Confier l'entretien au personnel qualifié.
AVIS: Pour eviter les risques d'incendie ou d’électrocution, n'exposez pas cet article à la
pluie ou a l'humidité.
ATTENTION: Pour diminuer le risque d’incendie, remplacer par des fusibles de même type
(voir caractéristiques).
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
humans.
The exclamation point, within an equilateral triangle, is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
EXPLICATION DES SYMBOLES GRAPHIQUES
Le symbole éclair avec point de flèche à l'intérieur d'un triangle équilatéral est utilisé pour
alerter l'utilisateur de la presence à l'intérieur du coffret de “voltage dangereux” non isolé
d'ampleur suffisante pour constituer un risque d'elétrocution.
Le point d'exclamation à l'intérieur d'un triangle équilatéral est employé pour alerter les
utilisateurs de la présence d'instructions importantes pour la fonctionnement et l'entretien
(service) dans le livret d'instruction accompagnant l'appareil.
DATE OF MANUFACTURE
The date of manufacture of this Anchor Audio product can be determined by the eight digit
serial number code. The fourth digit denotes the year, the third digit (letter) denotes the
month (A=Jan, B=Feb, etc.) Example: "AWDO1432" states that the unit was manufactured
in April of 2000.
Rated power output: 30 watts
Sensitivity for rated output:
Line: -20 dBV (100 mVrms)
Microphone: -43 dBV (7.5 mVrms)
Instrument: -30 dBV (30 mVrms)
Frequency response: 65 Hz – 18 kHz ± 3dB
Max SPL @ rated power: 101 dB @ 1 meter
Speaker type: 4.5 inch woofer, 10mm dome tweeter
Inputs
Line inputs (2): Hi-Z, unbalanced, RCA (summing L+R)
Microphone input: Lo-Z, unbalanced, 1/4"-phone
Instrument input: (3k), unbalanced, 1/4"-phone
DC output: 12 Volts DC, 100 mA max
RF Wireless Receiver: PLL Synthesized
Sensitivity: 2µV at S/N 40 dB
Frequency: 682.375 MHz - 697.125 MHz
AC Power requirements 110 - 125 VAC, 50/60 Hz
export model: 208 - 240 VAC, 50/60 Hz
(50 watts max)
Fuse rating: T 1.0A / 250V
export model: T 0.5A / 250V
(internally mounted)
Dimensions (HWD): 5.25 x 8.4 x 9", 13 x 21 x 23 cm
Weight: 8.5 lbs, 3.8 Kg
Specifications subject to change without notice.
12
NOTES
1
Quick Use Guide …………………………………… 2
Feedback Information ……………………………… 2
Getting Started ……………………………………… 3
General Operation ……………………………… 4-5
Wireless Operation ……………………………… 6-8
Wireless Remote Control ………………………… 9
Accessories …………………………………… 10-11
Specifications ……………………………………… 13
Troubleshooting Guide ………………… back cover
Thank you for choosing an Anchor Audio portable
sound system. Our products incorporate state-of-
the-art design and the finest quality of materials
and workmanship. We’re proud of our products and
appreciate the confidence which you have shown by
selecting an Anchor system.
I hope you’ll take a few of minutes to review this
manual. We’ve incorporated several unique features
into our products, and your knowledge of how to
use them will enhance the performance and your
enjoyment of the system.
David Jacobs, President
on behalf of all Anchor Employees
CONTENTS
112
QUICK USE GUIDE ACCESSORIES
The AN-130 monitor is used to amplify the signal from a microphone,
electronic musical instrument or line-level sources (cassette, CD,
VCR, etc). You’ll need a connection cable and an AC outlet.
Here’s How Easy It Is To Use:
1. Place the AN-130 at desired location.
2. Set volume control on front of speaker to minimum before
turning on the power.
3. Plug the power cord into a grounded 115 volt outlet (220
volt outlet for export model).
4. Plug a microphone into the MIC input jack, or an audio
source into the INST or LINE 1 / LINE 2 jacks.
5. Turn the power switch on the rear panel “ON”
(the red LED on front panel should light).
6. Adjust the volume, bass and treble controls for desired sound.
For general operating instructions, see the “General
Operation” section beginning on page 4.
Operating instructions for the wireless mic system on model
AN-130U1 are under “Wireless Operation” on pages 6 to 8.
Operating instructions for the AN-130RC remote control
are under “Wireless Remote Control” on page 9.
NOTE:
Problems?
Consult the
troubleshooting
section on the
back page of
this manual.
What Causes Feedback?
Feedback is a ringing, howling, or shrill sound that is self-generated
by the sound system. It is the result of sound from the speakers being
picked up by the microphone(s) in use and then re-amplified by the
system. This can form a self-sustaining loop that can damage the
sound system if allowed to continue.
How To Prevent Feedback
Always stand behind the speaker when using a microphone.
To avoid feedback, always make sure volume controls are at
minimum before turning unit on. If feedback occurs, immediately
reduce the volume.
CAUTION:
Feedback can
damage your
equipment
and may be
hazardous to
your hearing.
FEEDBACK INFORMATION
REMOTE-130 Wireless Remote Control
Controls volume up, down and mute for the AN-130RC.
MIC-90P Handheld Microphone
Professional dynamic, cardioid pattern handheld mic. Comes with a
20' cable with 1/4”-phone plug and mic clip.
WH-6000
UHF wireless handheld microphone/transmitter.
WB-6000
UHF wireless body-pack transmitter (order mic separately).
CM-60
CollarMic microphone for use with WB-6000, UHF wireless
body-pack transmitter.
HBM-60
Headband microphone for use with WB-6000, UHF wireless
body-pack transmitter.
LM-6000
Lapel microphone for use with WB-6000, UHF wireless body-pack
transmitter.
10
ACCESSORIES GETTING STARTED
System Inspection & Inventory
Check unit carefully for damage which may have occurred during
transit. Each Anchor product is carefully inspected at the factory
and packed in a special carton for safe transport.
Inventory
• AN-130 powered monitor
• Warranty registration card
All damage claims must be made with the freight carrier. Notify the
freight carrier immediately if you observe any damage to the
shipping carton or product. Repack the unit in the carton and await
inspection by the carriers claim agent. Notify your dealer of the
pending freight claim.
Returning Systems For Service or Repair
Should your unit require service, contact your dealer or the Anchor
Audio Customer Service Department at (800) 262-4671 to obtain a
Return Authorization (RA) number. All shipments to Anchor Audio
must include an RA number and must be shipped prepaid. C.O.D.
shipments will be refused and returned at your cost.
Warranty Registration
Please fill out the warranty card and return it with a copy of your
invoice to Anchors Customer Service Department. This will
activate your limited six year warranty.
NOTE:
All damage
claims must
be made with
the freight
carrier.
IMPORTANT:
Save the
shipping
carton and
packing
materials.
They were
specially
designed to
ship your unit
safely.
3
SS-250 Speaker Stand
Adjustable stand made of black, anodized aluminum.
MSB-201 Combination Mic/Speaker Stand
Floor stand with 33" adjustable boom. Doubles as speaker stand
when combined with SB-1 mounting bracket
HS-1 Carry Handle
Convenient attachable handle for AN-130.
CC-100 Carry Bag
Cordura nylon bag with storage compartment for AN-130.
HC-1550 Hard Case
Traveling hard case - holds up to two AN-130’s and two mics.
HC-1610B Hard Case
Projector Protector hard case - holds projector, AN-130 and mic.
SB-1 Swivel Stand Mounting Bracket
The SB-1 bracket can be used to mount the AN-130 to a wall,
ceiling or on a speaker stand (stand adapter included).
SB-3 Swivel Wall Mounting Bracket
Used for mounting the AN-130 to the wall or ceiling.
SB-360 Swivel (360°) Wall Mounting Bracket
Used for mounting the AN-130 to the wall or ceiling.
RM-1 Single Rackmount Kit
RM-12 Dual Rackmount Kit
Rackmount kits allow mounting of AN-130 monitors in a standard
equipment rack, three spaces high (5-1/4"). The rackmount kits are
adjustable (front/back), and include mounting hardware.
Color: satin black.
u
n
p
o
w
e
r
e
d
m
o
n
i
t
o
r
u
n
p
o
w
e
r
e
d
m
o
n
i
t
o
r
SB-1
SB-3
GENERAL OPERATION WIRELESS REMOTE CONTROL
Operating The Sound System
1. Place the AN-130 at desired location.
2. Set volume control on front of speaker to minimum before
turning on the power.
3. Plug the power cord into a grounded 115 volt outlet (220
volt outlet for export model).
4. Plug a microphone into the MIC input jack, or an audio
source into the INST or LINE 1 / LINE 2 jacks.
5. Turn the power switch “ON” (the red LED on front panel
should light).
6. Adjust the volume, bass and treble controls for desired
sound.
4
NOTE:
If no sound
can be
heard after
increasing
the volume
of your
AN-130RC,
lower the
volume, turn
the power
switch off
then back on.
Next slowly
increase the
volume to the
desired level.
CAUTION:
ALWAYS use
shielded
audio cables
on input
connections
to prevent
interference.
Mic Input
(1/4" phone jack)
Instrument Input
(1/4" phone jack)
Line Inputs - 2
(RCA jacks)
Wireless Channel SelectorWireless Mic Volume Control
AN-130U1 Back Panel
9
Remote Operation (AN-130RC only)
With the red, mute button facing towards the AN-130RC, aim the
remote at the red window located near the volume and tone controls.
Press the volume up button to increase the volume. Press the volume
down button to decrease the volume. To mute the AN-130RC, press
the mute button. To un-mute press the mute button again, or press
either volume button.
Replacing The Remote Battery
With the bottom of the remote facing up, locate the latch on the
bottom of the remote, near the back. Gently pull the latch towards
the center of the remote and carefully slide out the battery holder.
Place a new battery in the holder so that the positive symbol on the
battery is facing up. Carefully re-insert the battery holder. Use only
CR2025 or CR2032 type batteries.
Volume Down
Button
Mute Button
Volume Up
Button
WIRELESS OPERATION GENERAL OPERATION
8 5
Line Inputs (summing)
The line-level RCA input jacks may be used with audio sources such
as computers, VCR’s, and cassette tape or compact disc players.
The inputs may be used for two separate sources, or they may be
used to sum L+R stereo outputs to a mono signal without the need
for adapters.
Mic Input
An unbalanced, low impedance microphone input is for use with the
MIC-90P or other mics that have a 1/4" phone plug.
Instrument Input
The instrument input (1/4"-phone jack) is for guitars, keyboards or
any instrument with an electronic transducer. It may also be used for
wireless microphone receivers. The instrument input has a higher
sensitivity than the line input.
Note: All connections must be made with shielded cable to avoid
hum, buzzing, or radio interference.
DC Output (AN-130DC model only)
12 Volts DC output jack for use with wireless or other external
accessories; maximum capacity of 100 mA max.
Replacing Transmitter Battery
Handheld Transmitter:
1. Unscrew battery compartment cover on lower end of mic.
2. Install 2 fresh ‘AA’ alkaline batteries.
3. Replace the battery cover.
Body-pack Transmitter:
1. Slide open battery cover on front of transmitter box.
2. Install 2 fresh ‘AA’ alkaline batteries.
3. Close the battery cover.
CAUTION:
Harmful
feedback may
occur when
walking in
front of a
sound system
or speaker
with a
wireless
microphone.
Always point
mic away
from speakers.
NOTE:
Transmitter
power switch
must be in the
OFF position
when
changing
batteries.
Place batteries into slot
and slide forward
76
WIRELESS OPERATION WIRELESS OPERATION
Diversity Wireless by Anchor Audio
Anchor Audio UHF wireless is a 16 channel, diversity wireless
system that utilizes two independent antennae to receive signal. The
diversity feature means that the receiver will process the stronger of
the two antenna signals, effectively minimizing dropouts and
interference from other transmitting sources. The antennae are
mounted internally so there are no obstructions or risk of damage.
Wireless Microphone Operation
Both the receiver and microphone must be set to the same channel.
1. If you are using a body-pack transmitter, insert the plug from
the mic into the jack marked MIC on the transmitter.
2. Turn the transmitter power switch to ON.
(The red LED will flash when the mic is turned on.
If the red LED stays on, the battery is low.)
3. Turn the AN-130U1 power switch to ON.
4. The RX indicators will light (one indicator at a time lights)
when the wireless signal is being transmitted and received.
Receiver Channel Selection
Before you use your UHF wireless system,
you will need to select a wireless frequency
channel. The wireless receiver is mounted
inside the AN-130U1 and can be set to any
of 16 available channels.
1. Locate the Wireless Channel selector on the back panel.
2. Using the selector knob set the frequency of the receiver
to channel 1 thru 16.
Transmitter Channel Selection
Handheld Transmitter:
1. Unscrew battery cover on
lower end of microphone.
2. Set the channel selection
dial to match the channel
setting on the receiver.
3. Replace the battery cover.
Body-pack Transmitter:
1. The channel selection dial
is located on the side of
the transmitter.
2. Set the channel selection
dial to match the channel
setting on the receiver.
NOTE:
Be sure that
the MIC/LINE
switch is in
the “MIC”
position when
a mic is
plugged into
the TX.
NOTE:
If you are
experiencing
ongoing
interference
with your
wireless
system, the
selected
frequency
may be
incompatible
with other RF
systems in
your area.
Try a different
channel.
NOTE:
When using
more then
one wireless
unit, make
sure each
microphone
is set to a
different
channel
frequency.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Anchor AN-130 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues