Samsung DV22N6800HW Manuel utilisateur

Dryer

User manual

DV22N685*H* / DV22N680*H*

DV6850N_DC68-03650E-07_EN.indd 1 2021/10/20 14:56:38

Contents

English2

Contents

Safety information 4

What you need to know about the safety instructions 4

Important safety symbols 4

CALIFORNIA PROPOSITION 65 WARNING 5

Important safety precautions 5

Warnings 7

Cautions 7

Before installation 9

Key installation requirements 9

Location considerations 9

Electrical requirements 12

Installation 14

What’s included 14

Step-by-step installation 16

STEP 1 Connect the electrical wiring 16

STEP 2 Level the dryer 18

Drain hose (if necessary) 20

Installation checklist 23

Before using the dryer 23

Switching the door position 24

Before you start 28

Sort and load 28

Functional prerequisite 28

Operations 29

Control panel 29

Simple steps to start 32

Cycle overview 33

Cycle guide 34

Special features 36

SmartThings 37

DV6850N_DC68-03650E-07_EN.indd 2 2021/10/20 14:56:38

Contents

English 3

Maintenance 43

Control panel 43

Tumbler 43

Stainless steel tumbler 43

Dryer exterior 43

Lint lter 43

Water tank 45

Heat exchanger 46

Troubleshooting 48

Checkpoints 48

Information codes 50

Specications 51

Fabric care chart 51

Protecting the environment 52

Specication sheet 53

Cycle chart 54

DV6850N_DC68-03650E-07_EN.indd 3 2021/10/20 14:56:38

Safety information

SAVE THESE INSTRUCTIONS

English4

Safety information

Congratulations on your new Samsung dryer. This manual contains important information

on the installation, use and care of your appliance. Please take some time to read this

manual to take full advantage of your dryer’s many benets and features.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

What you need to know about the safety instructions

Please read this manual thoroughly to ensure that you know how to safely and efciently

operate the extensive features and functions of your new appliance. Please store the

manual in a safe location close to the appliance for future reference. Use this appliance

only for its intended purpose as described in this instruction manual.

Warnings and Important Safety Instructions in this manual do not cover all possible

conditions and situations that may occur. It is your responsibility to use common sense,

caution and care when installing, maintaining and operating your dryer.

Because the following operating instructions cover various models, the characteristics of

your dryer may differ slightly from those described in this manual and not all warning

signs may be applicable. If you have any questions or concerns, contact your nearest

service center or nd help and information online at www.samsung.com.

Important safety symbols

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury, death and/or

property damage.

CAUTION

Hazards or unsafe practices that may result in personal injury and/or property damage.

NOTE

Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to yourself and others.

Please follow them explicitly.

After reading this manual, store it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment that uses electricity and moving parts, potential hazards exist.

To safely operate this appliance, familiarize yourself with its operation and exercise care

when using it.

DV6850N_DC68-03650E-07_EN.indd 4 2021/10/20 14:56:38

Safety information

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

English 5

CALIFORNIA PROPOSITION 65 WARNING

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualied installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Save these instructions.

Important safety precautions

WARNING

To reduce the risk of re, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other ammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ammable substance,

such as vegetable oil, cooking oil, machine oil, ammable chemicals, paint thinner,

etc., or anything containing wax or chemicals, such as mops and cleaning cloths.

Flammable substances may cause the fabric to catch re by itself.

4. Do not store or use gasoline or other ammable vapors and liquids near this or any

other appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with internal controls.

DV6850N_DC68-03650E-07_EN.indd 5 2021/10/20 14:56:38

Safety information

SAVE THESE INSTRUCTIONS

Safety information

SAVE THESE INSTRUCTIONS

English6

10. Do not repair or replace any part of the appliance or attempt any service unless

specically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-

like materials.

14. The interior of the appliance should be cleaned periodically by qualied service

personnel.

15. Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch re.

To reduce the risk of re due to contaminated loads, the nal part of a tumble dryer

cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before

the end of the drying cycle unless all items are quickly removed and spread out so that

the heat is dissipated.

16. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in

“Installation” section.

17. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

18. Do not insert your hand under the dryer.

• This may result in injury.

19. Take care that children’s ngers are not caught in the door when closing it.

• This may result in injury.

DV6850N_DC68-03650E-07_EN.indd 6 2021/10/20 14:56:38

Safety information

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

English 7

WARNING - To reduce the risk of re or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other ammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or ammable liquids or solids should not be placed in the dryer until

all traces of these ammable liquids or solids and their fumes have been removed.

There are many highly ammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers.

• Do not dry items containing foam rubber (may be labeled latex foam) or similarly

textured rubber-like materials on a heat setting. Heated foam rubber materials can,

under certain circumstances, ignite spontaneously.

Warnings

WARNING

• Ensure pockets are free of small, irregularly shaped hard objects and foreign material,

i.e. coins, knives, pins, etc. These objects could damage your dryer.

• Sharp Edges – To reduce the risk of injury, use care when cleaning the condenser or

evaporator coil ns.

• Certain internal parts are intentionally not grounded and may present a risk of electric

shock only during servicing. Service Personnel - Do not contact the following parts

while the appliance is energized: Control board, Motor, Drain pump.

Cautions

CAUTION

• Do not allow children or pets to play on, in, or in front of the appliance. Close

supervision is necessary when the appliance is used near children and pets.

• Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

• Do not reach into the appliance when the drum is moving.

• Do not install or store this appliance where it will be exposed to the weather.

• Do not tamper with the controls.

• Do not repair, replace, or attempt to service any part of the appliance unless

specically instructed to in the user-repair instructions and you have the

understanding and skills to carry out the procedure.

DV6850N_DC68-03650E-07_EN.indd 7 2021/10/20 14:56:39

Safety information

SAVE THESE INSTRUCTIONS

Safety information

SAVE THESE INSTRUCTIONS

English8

• Do not use fabric softeners or products to eliminate static unless the softener or

product is recommended for dryer use by the manufacturer of the fabric softener or

product.

• Clean the lint screen before or after each load.

• Keep the area around the exhaust opening and surrounding areas free from lint, dust,

and dirt.

• The interior of the dryer and exhaust duct should be cleaned periodically by qualied

service personnel.

• This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately or not in accordance with local and national codes. See

the installation instructions for information about grounding this appliance.

• Do not sit on top of the dryer.

• Do not dry clothing with large buckles, buttons, or other heavy metal or solid objects.

• Install and use in accordance with the manufacturer’s instructions.

• Do not place items in your dryer that have been spotted or soaked with vegetable oil

or cooking oil. Even after being washed, these items may contain signicant amounts

of these oils.

• Residual oil on clothing can ignite spontaneously. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed

to heat. Heat sources such as your dryer can warm these items, allowing an oxidation

reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items

can become hot enough to catch re. Piling, stacking, or storing these kinds of items

may prevent heat from escaping and can create a re hazard.

• All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous.

Washing these items in hot water with extra detergent will reduce, but not eliminate,

the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying

cycle until the items have run through the Cool Down cycle. Never pile or stack these

items when they are hot.

DV6850N_DC68-03650E-07_EN.indd 8 2021/10/20 14:56:39

Before installation

English 9

Before installation

Read through the following instructions before installing the dryer, and keep this manual

for future reference.

WARNING

Certain internal parts are intentionally not grounded and may present a risk of electric

shock only during servicing. Service Personnel - Do not contact the following parts while

the appliance is energized: Control board, Motor, Drain pump.

Key installation requirements

• A grounded electrical outlet.

• A power cord for electric dryers (except

in Canada).

• A sink or drain pipe if you want to

drain the water captured during drying

through the supplied long drain hose.

(See page 20.)

WARNING

Remove the door from all discarded

appliances to prevent a child from

suffocating.

Location considerations

• Adequate clearances between the dryer

and adjacent walls or other surfaces.

• Adequate air circulation for ventilation.

• Away from water and weather.

WARNING

• Keep the dryer area clear of

combustible materials, gasoline, and

other ammable vapors and liquids.

• Do not install other fuel-burning

appliances around or in the same place

as the dryer.

• Place dryer at least 18 in (460 mm)

above the oor for a garage installation.

Alcove or closet installation

Minimum Clearance for stable operation:

Sides 1 in. (25 mm)

Top 1 in. (25 mm)

Rear 2 in. (50 mm)

Front 1 in. (25 mm)

The closet front must have two

unobstructed air openings for a combined

minimum total area of 72 in² (465 cm²)

with 3” (7.6 cm) minimum clearance on

the top and bottom. A louvered door with

equivalent space clearance is acceptable.

DV6850N_DC68-03650E-07_EN.indd 9 2021/10/20 14:56:39

Before installation

English10

Undercounter installation

A

BD

C

A34.4 in. (875 mm) C23.6 in. (600 mm)

B1 in. (25 mm) D1 in. (25 mm)

Side by side installation

A

E

A

AC

B B

F

D

A* 1 in. (25 mm) D25.6 in. (650 mm)

B23.6 in. (600 mm) E1 in. (25 mm)

C1 in. (25 mm) F2 in. (50 mm)

*This Clearance is not applicable to standalone dryer.

DV6850N_DC68-03650E-07_EN.indd 10 2021/10/20 14:56:39

Before installation

English 11

Stacked installation (Model: SK-DH)

A

KG

C

D

B

F

H I J

E

A3 in. (76 mm) G1 in. (25 mm)

B48 in². (310 mm²) H23.6 in. (600 mm)

C24 in². (155 mm²) I1 in. (25 mm)

D3 in. (76 mm) J27.1 in. (688 mm)

E6 in. (152 mm) K2 in. (50 mm)

F67 in. (1702 mm)

WARNING

Samsung’s washers and dryers can be stacked to maximize usable space.

You can purchase an optional stacking kit from your Samsung retailer.

DV6850N_DC68-03650E-07_EN.indd 11 2021/10/20 14:56:39

Before installation

English12

Electrical requirements

The wiring diagram is located on the plate

under the control panel or rear frame.

WARNING

• Improperly connecting the equipment

grounding conductor can result in a

risk of electric shock. Check with a

qualied electrician or serviceman if

you are in doubt as to whether your

dryer is properly grounded. Do not

modify the plug provided with your

dryer – if it doesn’t t the outlet, have

a proper outlet installed by a qualied

electrician.

• To prevent unnecessary risk of re,

electrical shock, or personal injury, all

wiring and grounding must be done in

accordance with local codes, or in the

absence of local codes, in accordance

with the National Electrical Code, ANSI/

NFPA No. 70-Latest Revision (for the

U.S.) or the Canadian Electrical Code CSA

C22.1 – Latest Revisions and local codes

and ordinances. It is your responsibility

to provide adequate electrical service

for your dryer.

Grounding

This dryer must be grounded. In the event

of a malfunction or breakdown, the ground

will reduce the risk of electrical shock by

providing a path of least resistance for the

electrical current.

WARNING

• Your dryer has an optional cord with

an equipment-grounding conductor

and a grounding plug. This cord is sold

separately.

• The plug must be plugged into an

appropriate outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

• Do not modify the plug provided with

your dryer – if it doesn’t t the outlet,

have a proper outlet installed by a

qualied electrician.

• If a power cord is not used and the

electric dryer is to be permanently

wired, the dryer must be connected to

a permanently grounded metal wiring

system, or an equipment grounding

conductor must be run with the circuit

conductors and connected to the

equipment grounding terminal or lead

on the dryer.

DV6850N_DC68-03650E-07_EN.indd 12 2021/10/20 14:56:39

Before installation

English 13

Electrical connections

Before operating or testing, follow all

grounding instructions in the “Grounding”

section. An individual branch (or separate)

circuit serving only your dryer is

recommended.

Do not use an extension cord.

U.S. only

Most U.S. dryers require a 240 volt, 60

Hz AC approved electrical service. Some

require 208 volt, 60 Hz approved electrical

service. The electric service requirements

can be found on the data label located

behind the door. A 30-ampere fuse or

circuit breaker on both sides of the line is

required.

• If a power cord is used, the cord

should be plugged into a 30-ampere

receptacle.

• The power cord is not provided with

U.S. electric model dryers. This cord is

sold separately.

WARNING

Risk of Electric Shock

When local codes allow, you can connect

the dryer’s electrical supply with a new

power supply cord kit, marked for use

with a dryer, that is U.L. listed and rated

at a minimum of 240 volts, 30-amperes

with three No. 10 copper wire conductors

terminated with closed loop terminals,

open-end spade lugs with turned up ends,

or with tinned leads.

• Do not reuse a power supply cord from

an old dryer. The power cord electric

supply wiring must be supported at the

dryer cabinet by a suitable UL-listed

strain relief.

• Grounding through the neutral

conductor is prohibited for (1) new

branch-circuit installations, (2) mobile

homes, (3) recreational vehicles, and

(4) areas where local codes prohibit

grounding through the neutral

conductor. (Use a 4-prong plug for a

4 wire receptacle, NEMA type 14-30R.)

Canada Only

• A 240 volt, 60 Hz AC approved

electrical service fused through a

30-ampere fuse or circuit breaker on

both sides of the line is required.

NOTE

All Canadian models are shipped with

the power cord attached. The power cord

should be plugged into a 30-ampere

receptacle.

In Canada, you may convert a dryer to 208

volt.

DV6850N_DC68-03650E-07_EN.indd 13 2021/10/20 14:56:39

Installation

English14

Installation

What’s included

Carefully unpack the dryer. Keep all packaging materials away from children. The parts

and location of parts shown below may differ from your dryer. Before installation, make

sure the dryer has all the parts listed here. If the dryer and/or parts are damaged or

missing, contact the nearest Samsung customer service center.

Dryer at a glance

01

02

05

04

07

03

06

01 Top cover 02 Water Tank

03 Door 04 Heat exchanger

05 Levelling Leg 06 Lint lter

07 Control Panel

DV6850N_DC68-03650E-07_EN.indd 14 2021/10/20 14:56:40

Installation

English 15

Accessories (supplied)

Hose guide Cable tie Hose connector

Long drain hose (6.5 ft/2 m) User manual Cleaning brush

Accessories (Canada Model Only)

Bracket-Stacking kit

(SK-DH)

NOTE

• The stacking kit allows the dryer to be stacked on top of a washer. Please note that the

stacking kit can only be used with Samsung washers and dryers. To purchase a bracket

stacking kit, contact a Samsung service center or local appliance retailer. The stacking

kit differs with the washer model.

• For stacking instructions for the dryer, see the installation manual included in the

stacking kit.

• For information about model-specic availability of the stacking kit, see the installation

manual included in the stacking kit.

DV6850N_DC68-03650E-07_EN.indd 15 2021/10/20 14:56:41

Installation

English16

Step-by-step installation

Make sure you have a qualied technician install the dryer. Step by step installation

instructions start below.

STEP 1 Connect the electrical wiring

First, read through the “Electrical requirements” section, and then follow the instructions

on this page or the next page. Instructions for a 3-wire system are on this page.

Instructions for a 4-wire system are on the next page.

For a 3-wire system

A

D

B

C

E

A. Center silver-colored terminal block

screw

B. Neutral wire (white or center wire)

C. Neutral grounding wire (white or green/

yellow)

D. ¾” (1.9 cm) UL-listed strain relief

E. External ground connector

1. Loosen or remove the screws from the

center terminal block.

2. Connect the neutral wire (white or

center wire) of the power cable to the

center, silver-colored terminal screw

of the terminal block. Tighten the

screws.

3. Connect the other wires to outer

terminal block screws. Tighten the

screws.

4. Tighten the strain relief screws.

5. Insert the terminal block cover into the

rear panel of the dryer. Then, secure

the cover with a hold-down screw.

CAUTION

• To convert from the 4-wire system

to 3-wire system, connect the ground

strap to the terminal block support to

ground the dryer frame to the neutral

conductor.

• Ring-type terminals are recommended.

If using strap terminals, make sure they

are tightened.

• Connect the power cord and check L1/

L2/N voltage. If the voltage is low, it

may not heat properly.

DV6850N_DC68-03650E-07_EN.indd 16 2021/10/20 14:56:41

Installation

English 17

For a 4-wire system

A

C

D

E

F

B

A. Center silver-colored terminal block

screw

B. Neutral grounding wire (white or green/

yellow)

C. ¾” (1.9 cm) UL-listed strain relief

D. Neutral wire (white or center wire)

E. External ground connector

F. Green or bare copper wire of power

cord

1. Remove the external ground

connector’s screw, and connect the

ground wire (green or unwrapped) of

the power cable to the screw.

CAUTION

• To connect the ground wire to the

neutral position without through

contact A (cabinet ground), contact

a technician. This is not user

serviceable.

• Ring-type terminals are

recommended. If using strap

terminals, make sure they are

tightened.

2. Loosen or remove the screws from the

center terminal block.

3. Connect the neutral wire (white or

center wire) and ground wire (white)

to the center, silver-colored terminal

screw of the terminal block. Tighten

the screw.

4. Connect the other wires to the outer

terminal block screws. Tighten the

screws.

5. Tighten the strain relief screws.

6. Insert the tab of the terminal block

cover into the rear panel of the dryer.

Then, secure the cover with a hold-

down screw.

CAUTION

Connect the power cord and check L1/L2/N voltage. If the voltage is low, it may not heat

properly.

WARNING

• All U.S. models are designed for a 3-wire system connection. The dryer frame is

grounded to the neutral conductor at the terminal block. A 4-wire system connection

is required for new or remodeled construction, mobile homes, or if local codes do not

permit grounding through neutral. If you use the 4-wire system, you cannot ground the

dryer frame to the neutral conductor at the terminal block.

DV6850N_DC68-03650E-07_EN.indd 17 2021/10/20 14:56:42

Installation

English18

• Remove the terminal block cover plate.

• Insert the power cord with a UL-listed strain relief through the hole provided in the

cabinet near the terminal block.

• A strain relief must be used.

• Do not loosen the nuts already installed on the terminal block. Be sure they are tight.

• Use a 3/8” (1 cm) deep well socket.

• Since january 1, 1996, The national electric code requires that new wiring (not existing)

utilize a 4-wire connection to this dryer.

STEP 2 Level the dryer

Before you install the dryer, make sure you have read the Installation requirements on

page 9. Please note that the following instructions are for installation without using a

drain hose. For instructions on using a drain hose, see the next section, Drain hose (if

necessary) on page 20. For convenience, consider installing the dryer next to your washer.

A

B

1. Carefully move the dryer to the desired

location.

2. Use a level (A) and check the levelness

of the dryer from side to side and front

to back.

3. If the dryer is not level, adjust the

levelling legs (B). Turning a leg counter-

clockwise retracts the leg. Turning a leg

clockwise extends the leg.

4. Once the dryer is level, make sure the

dryer stands rmly on the oor.

5. Plug in the dryer.

DV6850N_DC68-03650E-07_EN.indd 18 2021/10/20 14:56:42

Installation

English 19

C D

NOTE

• The dryer can be levelled using either

or both of the front and rear legs of the

dryer.

• To set the dryer to the same height as

the washer, fully retract (C) the levelling

legs by turning them counter clockwise,

then loosen (D) the legs by turning

them clockwise.

• Extend the levelling leg only as much

as necessary. Extending the levelling

leg more than necessary can cause the

dryer to vibrate.

DV6850N_DC68-03650E-07_EN.indd 19 2021/10/20 14:56:42

Installation

English20

Drain hose (if necessary)

Important: This dryer comes with a built in

water tank that stores water captured by

the dryer from drying clothes. The water

tank must be emptied manually before or

after each load. See page 45. However,

you can install the provided long drain

hose as described below and have the

water empty directly into a nearby sink or

drain pipe automatically.

B

A

1. Remove the drain hose from hole (A),

and insert it into hole (B).

DV6850N_DC68-03650E-07_EN.indd 20 2021/10/20 14:56:42

La page charge ...

Samsung DV22N6800HW Manuel utilisateur

Samsung DV22N6800HW Manuel utilisateur

dans d''autres langues

Documents connexes