Dell PowerEdge R810 Guide de démarrage rapide

Dell™ PowerEdge™

R810 Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell™ PowerEdge™

R810 Systems

Getting Started

With Your System

Regulatory Model E05S Series

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo and PowerEdge are trademarks of Dell Inc.;

Intel and Xeon are registered trademarks of Intel Corporation in the U.S. and other countries;

Microsoft, Windows, Windows Server and Hyper-V are either trademarks or registered trademarks

of Microsoft Corporation in the United States and/or other countries; SUSE is a registered trademark

of Novell, Inc. in the United States and other countries; Citrix and XenServer are trademarks

of Citrix Systems, Inc. and/or more of its subsidiaries, and may be registered in the United States

Patent and Trademark Office and in other countries; VMware is a registered trademark or trademark

(the “Marks”) of VMware, Inc. in the United States and/or other jurisdictions; Solaris is a trademark

of Sun Microsystems, Inc. in the United States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model E05S Series

November 2009 P/N Y849M Rev. A00

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

4 Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cable(s)

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cable(s)

Attach the power cable retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp.

Plug the other end of the power cable into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Complete the Operating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the installation and configuration documentation for your

operating system. Be sure the operating system is installed before installing

hardware or software not purchased with the system.

Supported Operating Systems

• Microsoft

®

Windows Server

®

2008 R2 Standard, Enterprise,

and Datacenter (x64) Editions

• Microsoft Windows Server 2008 Standard and Enterprise (x86) Editions

with SP2

• Microsoft Windows Server 2008 Standard, Enterprise, and

Datacenter (x64) Editions with SP2

• Microsoft Windows Server 2008 Standard and Enterprise (x86) Editions

Getting Started With Your System 7

• Microsoft Windows Server 2008 Standard, Enterprise, and

Datacenter (x64) Editions (with Hyper-V role enabled)

• Microsoft Windows Server 2003 Standard and Enterprise (x86) Editions

• Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions

• Microsoft Windows Server 2003 R2 Standard and Enterprise (x86)

Editions with SP2

• Microsoft Windows Server 2003 R2 Standard, Enterprise,

and Datacenter (x64) Editions with SP2

• Microsoft Windows Essential Business Server 2008 Standard and

Premium (x64) Editions

• Microsoft Windows Server 2008 Hyper-V™

• Microsoft Windows Server 2008 R2 Hyper-V

• Microsoft Hyper-V Server 2008 R2

•SUSE

®

Linux Enterprise Server 11 (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64) with SP3

•Solaris

®

10 10/9 (x86_64) (when available)

•VMware

®

ESX Version 4.0 Update 1

• VMware ESXi Version 4.0 Update 1

•Citrix

®

XenServer™ 5.6 (when available)

NOTE: For the latest information on supported operating systems,

see support.dell.com.

8 Getting Started With Your System

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

• The rack documentation included with your rack solution describes

how to install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document is available online at

support.dell.com/manuals

.

• Any media that ships with your system that provides documentation

and tools for configuring and managing your system, including those

pertaining to the operating system, system management software,

system updates, and system components that you purchased with

your system.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual. Dell™ offers

comprehensive hardware training and certification. See dell.com/training

for more information. This service may not be offered in all locations.

Getting Started With Your System 9

Technical Specifications

Processor

Processor type Up to four Intel

®

Xeon

®

7500 series processors

(up to eight core processors)

Or

Up to four Intel Xeon 6500 series processors

(up to eight core processors)

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots Riser 1

Slot 1: x8 link with x16 physical connector,

9.5-inch length, standard height

Slot 2: x4 link with x8 physical connector, low-profile,

with a standard height bracket

System Board

Slot 3: x8 link with x8 physical connector, low-profile

Slot 4: x8 link with x8 physical connector, low-profile

Riser 2

Slot 5: x8 link with x16 physical connector,

9.5-inch length, standard height

Slot 6: x8 link with x16 physical connector,

9.5-inch length, standard height

Memory

Architecture 1066 MHz DDR3 registered ECC DIMMs

Memory module sockets Thirty two 240-pin

Memory module capacities 1 GB, 2 GB, 4 GB, 8 GB, or 16 GB RDIMMs

(single, dual, or quad-rank depending on capacity)

Minimum RAM 4 GB (per processor)

NOTE: It is recommended that you install a minimum

of 16 GB to run applications.

Maximum RAM 512 GB (with 16 GB RDIMMs)

10 Getting Started With Your System

Drives

Hard drives Up to six 2.5-inch, internal hot-swappable

SAS, SATA, or SSD drives

Diskette drive Optional external USB 1.44 MB

Optical drive

One optional slimline SATA DVD-ROM

or DVD+RW drive

NOTE:

DVD devices are data only.

Flash drive Optional internal USB

Optional internal dual SD module

Optional vFlash card (with iDRAC6

Enterprise card)

Connectors

Back

NIC

Four RJ-45 (for integrated 1 GB NICs)

NIC (Management NIC)

One optional management NIC port on

iDRAC6 Enterprise card

Serial

9-pin, DTE, 16550-compatible

USB

Four 4-pin, USB 2.0-compliant

Video

15-pin VGA

vFlash

One optional vFlash memory card slot on

iDRAC6 Enterprise card

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

SD

Two optional internal SD modules

Getting Started With Your System 11

Video

Video type Integrated Matrox G200 with iDRAC6

Video memory 8 MB (shared with iDRAC application

memory)

Power

AC power supply

Wattage (per power supply)

1100 W

Voltage (per power supply)

100–240 V, 50/60 Hz, auto-ranging

System heat dissipation

4012 BTU/Hr

Maximum inrush current

(per power supply)

Under typical line conditions and over

the entire system ambient operating range,

the inrush current may reach 55 A per power

supply for 10 ms or less

Batteries

System battery

CR 2032 3.0-V lithium coin cell

RAID battery (optional)

3.7 V lithium ion

Physical

Height 8.642 cm (3.40 in)

Width 44.05 cm (17.34 in) without bezel

48.24 cm (18.99 in) with bezel

Depth 72.06 cm (28.37 in) without bezel

75.56 cm (29.75 in) with bezel

Weight (maximum configuration) 26.1 kg (57.54 lb)

Weight (empty) 21.15 kg (46.64 lb)

12 Getting Started With Your System

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet,

the maximum operating temperature is

derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with

a maximum temperature gradation of

20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with

a maximum humidity gradation of

10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 G at 5–350 Hz for 15 min

Storage

0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational orientation

Storage

Six consecutively executed shock pulses

in the positive and negative x, y, and z axes

(one pulse on each side of the system)

of 71 G for up to 2 ms

Getting Started With Your System 13

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Environmental (continued)

14 Getting Started With Your System

Systèmes Dell™

PowerEdge™ R810

Guide de mise en route

Modèle réglementaire série E05S

Remarques, précautions et avertissements

REMARQUE : une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre ordinateur.

PRÉCAUTION : une PRÉCAUTION vous avertit d'un risque d'endommagement du

matériel ou de perte de données en cas de non-respect des instructions données.

AVERTISSEMENT : un AVERTISSEMENT vous avertit d’un risque d'endom-

magement du matériel, de blessure corporelle ou de mort.

____________________

Les informations contenues dans ce document sont sujettes à modification sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques mentionnées dans ce document : Dell, le logo DELL et PowerEdge sont des marques

de Dell Inc. ; Intel et Xeon sont des marques déposées d'Intel Corporation aux États-Unis et dans

d'autres pays ; Microsoft, Windows, Windows Server et Hyper-V sont des marques ou des marques

déposées de Microsoft Corporation aux États-Unis et/ou dans d'autres pays ; SUSE est une marque

déposée de Novell, Inc. aux États-Unis et dans d'autres pays ; Citrix et XenServer sont des marques

de Citrix Systems, Inc. et/ou de plusieurs de ses filiales et peuvent être déposées auprès du Patent and

Trademark Office aux États-Unis et d'organismes similaires dans d'autres pays ; VMware est une

marque ou une marque déposée (les “marques”) de VMware, Inc. aux États-Unis et/ou dans d'autres

juridictions ; Solaris est une marque de Sun Microsystems, Inc aux États-Unis et dans d'autres pays.

D'autres marques commerciales et noms de marque peuvent être utilisés dans ce document pour faire

référence aux entités se réclamant de ces marques et de ces noms ou de leurs produits. Dell Inc. dénie

tout intérêt propriétaire vis-à-vis des marques et des noms de marques autres que les siens.

Modèle réglementaire série E05S

Novembre 2009 N/P Y849M Rév. A00

Guide de mise en route 17

Installation et configuration

AVERTISSEMENT : avant de suivre la procédure suivante, lisez les consignes

de sécurité fournies avec le système.

Déballage du système

Sortez le système de son emballage et identifiez chaque élément.

Installation des rails et du système dans un rack

Assemblez les rails et installez le système dans le rack en suivant les consignes

de sécurité et les instructions d'installation du rack fournies avec votre

système.

18 Guide de mise en route

Facultatif – Connexion du clavier, de la souris et du moniteur

Connectez le clavier, la souris et le moniteur (si nécessaire).

Les icônes des connecteurs situées à l'arrière du système indiquent où insérer

chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble

du moniteur, s'il en est équipé.

Branchement du ou des câbles d'alimentation

Branchez le ou les câbles d'alimentation au système et, si vous utilisez

un moniteur, connectez son câble d'alimentation à celui-ci.

La page charge ...

Dell PowerEdge R810 Guide de démarrage rapide

Dell PowerEdge R810 Guide de démarrage rapide

dans d''autres langues

Documents connexes