Samsung HW-LST70T Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
HW-LST70T
FULL MANUAL
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at www.samsung.com/register
ENG - 2
SAFETY INFORMATION
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Refer to the table below for an explanation of
symbols which may be on your Samsung product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that high voltage
is present inside. It is dangerous to
make any kind of contact with any
internal part of this product.
This symbol indicates that this product
has included important literature
concerning operation and maintenance.
Class II product : This symbol indicates
that it does not require a safety
connection to electrical earth (ground).
If this symbol is not present on a
product with a power cord, the product
MUST have a reliable connection to
protective earth (ground).
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to
consult the user manual for further
safety related information.
WARNING
To prevent injury, this apparatus must be
securely attached to the oor/wall in
accordance with the installation instructions.
CAUTION
To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.
CAUTION (for Canada)
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
This device and its antenna(s) must not be co-
located or operation in conjunction with any other
antenna or transmitter.
This device may automatically discontinue
transmission if there is no information to
transmit, or an operational failure. Note that this
is not intended to prohibit the transmission of
control or signaling information or the use of
repetitive codes where required by the
technology.
This Class B digital apparatus complies with
Canadian ICES-003.
ENG - 3
Radiation Exposure Statement
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment should
be installed and operated with minimum distance
20 cm between the radiator & your body.
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below. Keep these operating
instructions handy for future reference.
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
7. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce
heat.
8. Do not defeat the safety purpose of the
polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type plug
has two blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided plug
does not t into your outlet, consult an
electrician for replacement of the obsolete
outlet.
9. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
10. Only use attachments/accessories specied
by the manufacturer.
11. Use only with the cart, stand,
tripod, bracket, or table
specied by the manufacturer,
or sold with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
13. Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as damage to the power-supply cord or
plug, product malfunction, and product
fall-down.
ENG - 4
PRECAUTIONS
1. Ensure that the AC power supply in your
house complies with the power
requirements listed on the identication
sticker located on the bottom of your
product. Install your product horizontally, on
a suitable base (furniture), with enough
space around it for ventilation (3~4 inches).
Make sure the ventilation slots are not
covered. Do not place the unit on ampliers
or other equipment which may become hot.
This unit is designed for continuous use.
To fully turn off the unit, disconnect the AC
plug from the wall outlet. Unplug the unit if
you intend to leave it unused for a long
period of time.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
other heat sources. This could lead to
overheating and cause the unit to
malfunction.
4. Protect the product from excess heat (e.g. a
replace) or equipment creating strong
magnetic or electric elds. Unplug the power
cable from the AC wall socket if the unit
malfunctions. Your product is not intended
for industrial use. It is for personal use only.
Condensation may occur if your product has
been stored in cold temperatures. If
transporting the unit during the winter, wait
approximately 2 hours until the unit has
reached room temperature before using.
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery
in the general household trash. Do not
expose the battery to excess heat, direct
sunlight, or re. Do not short circuit,
disassemble, or overheat the battery.
Danger of explosion if the battery is replaced
incorrectly. Replace only with the same or
equivalent type.
6. Despite the IP55 rating, your Soundbar is not
impervious to water damage in any situation.
To help prevent damage to your product,
avoid the product being subjected to:
Water projected by a source greater than
0.25 inches (6.3 mm) against enclosure
from any direction or submersion in
water;
Water projected at greater than 30 KPa
(4.4 PSI) with a water volume greater
than 12.5 L/minute for more than
3 minutes; and
Extreme weather conditions.
ENG - 5
CONTENTS
01 Checking the Components 7
Inserting Batteries before using the Remote Control
(AAA batteries X 2) ------------------------- 8
02 Product Overview 9
Front Panel / Bottom Panel of the Soundbar ------------------------- 9
Rear Panel of the Soundbar ------------------------- 10
03 Using the Remote Control 11
How to Use the Remote Control
-------------------------
11
Using the Hidden Buttons (Buttons with more than one function)
-------------------------
14
Output specications for the different sound effect modes
-------------------------
14
Adjusting the Soundbar volume with a TV remote control ------------------------- 15
04 Connecting the Soundbar 16
Connecting Electrical Power
-------------------------
16
How to mount the AC/DC adapter
-------------------------
16
05 Using a wired connection to the TV 17
Connecting using an Optical Cable
-------------------------
17
06 Using a wireless connection to the TV 19
Method 1. Connecting via Bluetooth
-------------------------
19
Method 2. Connecting via Wi-Fi
-------------------------
21
07 Connecting an External Device 22
Connecting using an Optical Cable
-------------------------
22
ENG - 6
08 Connecting a Mobile Device 23
Method 1. Connecting via Bluetooth
-------------------------
23
Method 2. Connecting via Wi-Fi (Wireless Network)
-------------------------
26
Using the Tap Sound
-------------------------
27
09 Connecting an Amazon product 28
Connect and use with an Amazon product (Amazon Echo) ------------------------- 28
Use voice commands to control the Soundbar
-------------------------
28
10 Installing the Wall Mount 29
Installation Precautions
-------------------------
29
Method 1. TV mount
-------------------------
29
Method 2. Wall mount
-------------------------
32
11 Software Update 34
Auto Update
-------------------------
34
USB Update
-------------------------
34
Initialization
-------------------------
34
12 Troubleshooting 35
13 License 36
14 Open Source License Notice 37
15 Important Notes About Service 37
16 SpecicationsandGuide 38
Specications
-------------------------
38
ENG - 7
01 CHECKING THE COMPONENTS
Soundbar Main Unit Soundbar Remote Control /
Batteries
Optical Cable
x 2
AC/DC Adapter Wall Mount Guide Holder-Screw
x 2
x 2
x 2
x 2
Bracket-Top Bracket-Bottom Bracket-Guide Bracket-Wall Mount
x 4
(M3 x L10)
x 2
(M4 x L10)
x 2
(M6 x L10)
x 2
x 2
(M5 x L50)
x 2
Screw-Taptype Screw-Machine Bolt-Etc A/S Bolt-Etc Anchor / Screw
For more information about the power supply and power consumption, refer to the label attached
to the product. (Label: Bottom of the Soundbar Main Unit)
To purchase additional components or optional cables, contact a Samsung Service Center or
Samsung Customer Care.
For Soundbar wall mounting components, see pages 29~33.
This Soundbar is intended only for TV mount or wall mount.
Design, specications, and App screen are subject to change without prior notice.
The appearance of the accessories may differ slightly from the illustrations above.
ENG - 8
Inserting Batteries before using the Remote Control
(AAA batteries X 2)
1
1
3
2
3
2
1.
Press the ^ button at the top rear of the Soundbar remote control. The body will pop out slightly
from the body cover.
2. Turn the remote over, push the body of the remote upwards until the battery compartment is
revealed, and then remove the battery cover.
3. If there are batteries in the remote, to remove the existing batteries.
4.
Insert two new batteries (1.5V AAA type) into the battery compartment making sure that the
batteries’ polarities (+, -) are oriented correctly.
5.
Once the batteries have been inserted, attach the battery cover and then slide down the body of
the remote.
6.
Turn the remote over, press and hold the ^ button on the top rear, and then slide the body of the
remote down into place.
Alkaline batteries are recommended for longer battery life.
ENG - 9
02 PRODUCT OVERVIEW
Front Panel / Bottom Panel of the Soundbar
Bottom Panel
Position the product so that the SAMSUNG logo is located on the top.
󰟴
󰟳
󰟵 󰟶
󰟳
Display
Displays the product’s status and current mode.
󰟴
(Power) Button
Turns the power on and off.
󰟵
(Volume) Button
Adjusts the volume.
󰟶
(Source) Button
Selects the source input mode.
Input mode Display
Optical Digital input D.IN
Wi-Fi mode WIFI
BLUETOOTH mode BT
When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and
change the TV speaker to External Speaker.
ENG - 10
Rear Panel of the Soundbar
SERVICE
DC 23V
DIGITAL
AUDIO IN
(OPTICAL)
SERVICE
DC 23V
DIGITAL
AUDIO IN
(OPTICAL)
󰟳
󰟴
󰟵
󰟳
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device. (See page 22)
󰟴
SERVICE
Connect a USB storage device to upgrade the product's software.
󰟵
DC 23V (Power Supply In)
Connect the AC/DC power adapter. (See page 16)
When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.
Do not pull the cable.
Do not connect this unit or other components to an AC outlet until all connections between
components are complete.
ENG - 11
03 USING THE REMOTE CONTROL
How to Use the Remote Control
󰟳
󰟵
󰟴
󰟶
󰟸
󰟹
󰟷
󰟺
󰟼
󰟻
󰟽
󰠀
󰟾
󰟿
󰟳
Power
Turns the Soundbar on and off.
Auto Power Down Function
The unit turns off automatically in the following
situations:
In D.IN / Wi-Fi / BT mode if there is no audio
signal for 18 minutes.
󰟴
D.IN
Press to enter the “D.IN” mode.
󰟵
Source
Press to select a source connected to the Soundbar.
󰟶
Mute
Press the (Mute) button to mute the sound.
Press it again to unmute the sound.
󰟷
Sound
Control
When pressed, the setting items such as TREBLE, or
SYNC are displayed in sequence. The desired item
can be adjusted using the Up/Down buttons.
To adjust the TREBLE volume, select Sound
Control → TREBLE, and then use the Up/Down
buttons to adjust the volume within a -6 to +6
range.
Press and hold the (Sound Control) button
for about 5 seconds to adjust the sound for each
frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz,
2.5kHz, 5kHz, and 10kHz are selectable using
the Left/Right buttons and each can be
adjusted to a setting between -6 to +6 using
the Up/Down buttons. (Make sure the Sound
mode is set to “STANDARD”.)
If the video on the TV and audio from the
Soundbar are not synchronized, select SYNC in
Sound Control, and then set the audio delay
between 0~300 milliseconds by using the Up/
Down buttons.
SYNC is only supported for some functions.
ENG - 12
󰟸
VOLUME
Push the button up or down to adjust the volume.
Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
󰟹
STANDARD
Press this button to outputs the original sound.
󰟺
Bluetooth
PAIR
Switch the Soundbar to Bluetooth pairing mode. Press the button and wait for the “BT
PAIRING” screen to connect to a new Bluetooth device.
󰟻
Play / Pause
You can also play or pause music by pressing the button.
󰟼
Up/Down/
Left/Right
VOL WOOFER
SOUND
MODE
PAIR
Press the indicated areas to select Up/Down/Left/Right.
Press Up/Down/Left/Right on the button to select or set functions.
Repeat
To use the Repeat function, press the Up button.
Music Skip
Press the Right button to select the next music le. Press the Left button to select the
previous music le.
󰟽
Info
When pressed, the information for the connected sources and Bluetooth devices appears.
ENG - 13
󰟾
BASS
Push this button up or down to adjust the bass volume within a -6 to +6 range.
󰟿
ADAPTIVE
Press this button to analyzes the content in real time and automatically provides the optimal
sound eld based on the characteristics of the content.
󰠀
SURROUND
Press this button to provide a wider sound stage than standard.
ENG - 14
Using the Hidden Buttons (Buttons with more than one function)
Hidden Button
Reference page
Remote Control Button Function
BASS (Up) TV remote control On/Off (Standby) page 15
(Sound Control)
7 Band EQ page 11
Outputspecicationsforthedifferentsoundeffectmodes
Effect Input Output
STANDARD
2.0 ch 2.0 ch
5.1 ch 3.0 ch
SURROUND
2.0 ch 3.0 ch
5.1 ch 3.0 ch
ADAPTIVE
2.0 ch 2.0 ch
5.1 ch 3.0 ch
ENG - 15
Adjusting the Soundbar volume with a TV remote control
Adjust the Soundbar volume using the TV’s remote control.
This function can be used with IR remote controls only. Bluetooth remote controls (remote
controls that require pairing) are not supported.
Set the TV speaker to External Speaker to use this function.
Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA
1. Turn Off the Soundbar.
2. Push up and hold the BASS button for 5 seconds.
Each time you push the BASS button up and hold it for 5 seconds, the mode switches in the
following order:SAMSUNG-TV REMOTE” (Default mode), “OFF-TV REMOTE”, “ALL-TV REMOTE”.
Remote Control Button Display Status
5 Sec
(Default mode)
SAMSUNG-TV REMOTE
Enable a Samsung TV’s IR remote
control.
5 Sec
OFF-TV REMOTE
Disable the TV remote control.
5 Sec
ALL-TV REMOTE
Enable a third-party TV’s IR
remote control.
ENG - 16
04 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Connect the Soundbar to an electrical outlet in the
following order:
1. Connect the AC/DC adapter to the Soundbar.
2. Connect the power cord to a wall socket.
For more information about the required
electrical power and power consumption,
refer to the label attached to the product.
(Label: Bottom of the Soundbar Main Unit)
NOTES
If you unplug and reconnect the power
cord when the product is turned on, the
Soundbar turns on automatically.
Never forcibly pull the power cord of AC/
DC adapter.
When installing the AC/DC adapter
horizontally, place it with the Samsung
logo facing upward.
This product may not operate safely under
-4°F (-20 °C). It is recommended to
connect the power cable to the outlet and
after 1 hour, turn on the Soundbar power .
Rear of the Soundbar Main Unit
SERVICE
DC 23V
DIGITAL
AUDIO IN
(OPTICAL)
SERVICE
DC 23V
DIGITAL
AUDIO IN
(OPTICAL)
AC/DC Adapter
While the cable is not in use, seal it with
waterproof silicone.
How to mount the AC/DC
adapter
Tighten 2 or 4 screws (not supplied) on the
wall or table and then insert them into the
grooves on the rear of the AC/DC adapter.
You cannot install the adapter directly on
the oor.
For the mounting screws, see the following
gures.
RecommendedScrewspecication
(not supplied)
L12
M3
0.26”
(6.5 mm)
0.18
(4.5 mm)
ENG - 17
05 USING A WIRED CONNECTION TO THE TV
Connecting using an Optical Cable
When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on
your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on
the TV is changed, you will experience better sound quality. (The TV menu may use different words for
Dolby Digital and PCM depending on the TV manufacturer.)
Pre-connection Checklist
When using the Soundbar outdoors, it is recommended to connect an Optical cable for smooth
sound output.
Be sure to use the optical cable provided with the product.
To purchase any optical cable separately, contact the nearest dealer or Samsung Service Center.
The optical cable provided with the product is designed to meet the specication (0.16 inches (4 mm))
for waterproong. When using an optical cable purchased from other site, the waterproof function
may not work properly.
When you use an optical cable and the terminals have covers, be sure to remove the covers.
SERVICE
DC 23V
DIGITAL
AUDIO IN
(OPTICAL)
OPTICAL OUT
Optical Cable
Rear of the Soundbar
D.IN
Bottom of the Soundbar
ENG - 18
1. With the TV and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port on the
Soundbar and the OPTICAL output port on the TV with the optical cable, as shown in the gure.
2. Turn on the Soundbar and TV.
3. Select “D.IN” mode by pressing the (Source) button on the bottom of the Soundbar or the D.IN
button on the Soundbar remote control.
4. The TV sound is output from the Soundbar.
ENG - 19
06 USING A WIRELESS CONNECTION TO THE TV
Pre-connection Checklist
When used outdoors, wireless performance may degrade. Accordingly, use the provided optical
cable if possible.
Method 1. Connecting via Bluetooth
When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
Only one Samsung TV can be connected at a time.
Samsung TV that supports Bluetooth can be connected. Check the specications of your TV.
Bottom of the Soundbar
OR
BT PAIRING
5 Sec
The initial connection
1. Press the PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode.
(OR)
a. Press the (Source) button on the bottom panel and then select “BT”.
BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if
there is a connect record.
b. When “BT READY” appears, press and hold the (Source) button on the bottom panel
of the Soundbar for more than 5 seconds to display “BT PAIRING”.
2. Select Bluetooth mode on the Samsung TV.
(e.g. Home ( ) Settings ( ) Sound Sound Output Bluetooth Speaker List
[AV] Samsung Soundbar LST70T (Bluetooth))
ENG - 20
3. Select “[AV] Samsung Soundbar LST70T” from the list on TV’s screen.
An available Soundbar is indicated with “Needs Pairing” or “Paired” on the TV’s Bluetooth device
list. To connect the Samsung TV to the Soundbar, select the message, and then establish a
connection.
When the Samsung TV is connected, [TV] NameBT” appears on the Soundbar’s front display.
4. You can now hear Samsung TV sound from the Soundbar.
After you have connected the Soundbar to your Samsung TV the rst time, use the “BT READY
mode to reconnect.
If the device fails to connect
If you have an existing Soundbar (e.g., [AV] Samsung Soundbar LST70T) on the list of speakers
on the Samsung TV, delete it.
Then repeat steps 1 through 3.
Disconnecting the Soundbar from the Samsung TV
Press the (Source)
button on the bottom panel or on the remote control and switch to any mode but
BT”.
Disconnecting takes time because the Samsung TV must receive a response from the Soundbar.
(The time required may differ, depending on the Samsung TV model.)
What is the difference between BT READY and BT PAIRING?
BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was
connected before.
BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR
button on the Soundbar remote control or press and hold the (Source) button on the
bottom of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Samsung HW-LST70T Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur

dans d''autres langues