NewAge Products 80642 Guide d'installation

KITCHEN

STORAGE ACCESSORIES

INSTALLATION GUIDE

ATTENTION: Is your Storage Accessory damaged?

Need help or spare parts? For fastest service,

contact NewAge Products at 1-877-306-8930;

or suppor[email protected]om.

Do not return to the retailer.

STOP

IM-HKC.02A-01 REV 1.1

Index

Product Inspection 3

Tools Needed 3

Maintenance and Care 3

Installing the Pull out 50L bin 4

Installing the Magic Corner 6

Installing the Iron Board 8

Installing the 18”, 24”, 36” Pants Display Rack 10

Installing the 18” and 24” Closet Rod on Cabinet Walls 12

Installing the 18” and 24”Closet Rod on Cabinet Shelf 14

Installing the 18”, 24”, 36” Pull out Hamper Basket 16

Installing the Under Sink Organizer 19

Installing the 12” and 18” Double Pull-out Basket 22

Installing the 18”, 24”, 36” Pull-out Basket 24

5 YEAR LIMITED WARRANTY 26

3

Product Inspection

• Check to see all parts are received as per the

order placed.

• Contact NewAge Products at 1-877-306-8930;

for any missing parts.

• Inspect the products for any damages before

starting the installation.

• Go through the installation instructions carefully

before starting the installation.

• Wipe and clean the accessory with a soft cloth. Do not use the scourers, abrasives or chemical

cleaners.

• Keep the slides out of water to protect the slides, thus make sure the smooth sliding.

Tools Needed

Maintenance and Care

#2 Philips Head

Screw Driver

Pencil

Cordless Drill

(Optional)

#2 Philips BitDrill Bit

3/16”

Level

4

Installing the Pull out 50L bin

#2 Philips Head

Screw Driver

Pencil

M5 x 16mm

Melamine Screw

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

back

4

0.67in (17mm)

3.72in (94.5mm)3.15in (80mm)

SKU #80671, 80672

50L, 35L

Garbage Pullout Bin

Lay this template at on the interior base of the cabinet.

Tools Required:

These templates are designed

to drill the proper mounting

holes for your cabinet

accessories. These templates

are for NewAge Cabinets and

accessories only.

1 x Cordless Power Drill

1 x Pencil

1 x 3/16” Drill Bit

Note: Do not drill through

entire cabinet

1

Align the left or right edge of the template with the left

or right side of the interior cabinet based on the

preferred installation location

Ensure the arrows below are aligned with the front

edge of the cabinet and mark the specied locations

with a pencil.

Drill pilot holes into the

marked locations using an

3/16” drill bit.

2

3

4

2

3

2

back

4

0.67in (17mm)

3.72in (94.5mm)3.15in (80mm)

SKU #80671, 80672

50L, 35L

Garbage Pullout Bin

Lay this template at on the interior base of the cabinet.

Tools Required:

These templates are designed

to drill the proper mounting

holes for your cabinet

accessories. These templates

are for NewAge Cabinets and

accessories only.

1 x Cordless Power Drill

1 x Pencil

1 x 3/16” Drill Bit

Note: Do not drill through

entire cabinet

1

Align the left or right edge of the template with the left

or right side of the interior cabinet based on the

preferred installation location

Ensure the arrows below are aligned with the front

edge of the cabinet and mark the specied locations

with a pencil.

Drill pilot holes into the

marked locations using an

3/16” drill bit.

2

3

4

2

3

2

back

4

0.67in (17mm)

3.72in (94.5mm)3.15in (80mm)

SKU #80671, 80672

50L, 35L

Garbage Pullout Bin

Lay this template at on the interior base of the cabinet.

Tools Required:

These templates are designed

to drill the proper mounting

holes for your cabinet

accessories. These templates

are for NewAge Cabinets and

accessories only.

1 x Cordless Power Drill

1 x Pencil

1 x 3/16” Drill Bit

Note: Do not drill through

entire cabinet

1

Align the left or right edge of the template with the left

or right side of the interior cabinet based on the

preferred installation location

Ensure the arrows below are aligned with the front

edge of the cabinet and mark the specied locations

with a pencil.

Drill pilot holes into the

marked locations using an

3/16” drill bit.

2

3

4

2

3

2

Tools and parts needed.

Place the template on the bottom of the

cabinet and align it to the front and side of

the cabinet.

Mark the drill holes layed out on the

template.

Drill holes at the marked locations using

3/16” mm drill bit while ensuring not to

drill through the bottom panel.

11

2 3

5

Insert the metal basket assembly and align the bracket holes to the drilled holes in the

cabinet. Using a screwdriver or cordless drill fasten the basket assembly using eight

M5x16mm screws included with the basket assembly. Make sure the cross posts are

installed on the basket assembly as shown in the image (A).

Slide the metal basket out and insert the bin. Adjust the cross posts to secure garbage bin.

1

6

Installing the Pull out 50L bin

4

A

6

Installing the Magic Corner

#2 Philips Head

Screw Driver

Pencil

M5 x 8 mm

Melamine Screw

M5 x 16mm

Melamine Screw

#2 Philips Bit

M4 x 8 mm

Melamine Screw

Cordless Drill

(optional)

Level

Drill Bit

3/16”

A

B

A

14.09in (358mm)

14.09in (319mm)

5.9in (150mm) 5.9in (150mm) 5.9in (150mm) 3.11in (79mm)

0.75in (19.5mm)

3.77in (96mm)

3.11in (79mm)

SKU #80691

Magic Corner

These templates are designed to

drill the proper mounting holes for

your cabinet accessories. These

templates are for NewAge

Cabinets and accessories only.

Lay this template at on the

interior base of the cabinet.

Tools Required:

1 x Cordless Power Drill

1 x Pencil

1 x 3/16” Drill Bit

Note: Do not drill through

entire cabinet

1

Align edge A with the left

side of the interior cabinet.

2

Ensure the arrows below,

marked B, are aligned with

the interior front edge of

the cabinet (Refer to image

C below) and mark the

specied locations with a

pencil.

3

Drill pilot holes into the

marked locations using an

3/16” drill bit.

4

Installation as shown in Cabinet: (not to scale)

Interior Front Edge

C

Tools and parts needed.

Place the template on the bottom of the

cabinet and align it to the front and side of

the cabinet.

Mark the drill holes layed out on the

template.

Drill holes at the marked locations using

3/16” mm drill bit while ensuring not to

drill through the bottom panel.

11

2 3

A

B

A

14.09in (358mm)

14.09in (319mm)

5.9in (150mm) 5.9in (150mm) 5.9in (150mm) 3.11in (79mm)

0.75in (19.5mm)

3.77in (96mm)

3.11in (79mm)

SKU #80691

Magic Corner

These templates are designed to

drill the proper mounting holes for

your cabinet accessories. These

templates are for NewAge

Cabinets and accessories only.

Lay this template at on the

interior base of the cabinet.

Tools Required:

1 x Cordless Power Drill

1 x Pencil

1 x 3/16” Drill Bit

Note: Do not drill through

entire cabinet

1

Align edge A with the left

side of the interior cabinet.

2

Ensure the arrows below,

marked B, are aligned with

the interior front edge of

the cabinet (Refer to image

C below) and mark the

specied locations with a

pencil.

3

Drill pilot holes into the

marked locations using an

3/16” drill bit.

4

Installation as shown in Cabinet: (not to scale)

Interior Front Edge

C

7

Installing the Magic Corner

Insert the sliding base and align the

bracket holes to the drilled holes in the

cabinet. Using a screwdriver or cordless

drill fasten the basket assembly using the

eight M5x16 screws included with the

Magic corner.

Slide the top frame and attach the handles

using two M4x8mm screws. Attach

bottom brackets (B) to the top frame using

eight M5x8 screws included with the

assembly and screw in the two handles on

top.

Insert the top frame assembly and align

the bracket holes with the holes on

the sliding base. Using a screwdriver

or cordless drill fasten the top frame

assembly using the eight M5x8 screws

included with the assembly.

Slide the top frame assembly out and

install the metal baskets.

11

2 7

5

6

4

B

8

Installing the Iron Board

#2 Philips Head

Screw Driver

Pencil

M5 x 16mm

Melamine Screw

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

Tools and parts needed.

Place the Iron board at desired position on

the cabinet shelf. Ensure shelf is leveled

Slide the iron board out from the frame.

(Note: Use two or more people to hold

the iron board in position.)

Mark the holes on the sliding frame base.

Drill holes at the marked locations using

3/16 mm drill bit.

11

2 3

9

Place the iron board, slide out and

fasten the iron board to shelf using

eight M5x16mm screws included in the

assembly.

Slide the ironing board in to nish the

installation.

11 54

Installing the Iron Board

10

Installing the 18”, 24”, 36” Pants Display Rack

#2 Philips Head

Screw Driver

Pencil

M5 x 16mm

Melamine Screw

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

L

1.5 in

Tools and parts needed.

Draw a horizontal line on the cabinet walls

at desired height (L).

Mark a hole at 1.5 in from the front on the

horizontal line.

Insert the side mounted slide and align

the rst hole on the slide with the marked

hole position. Use the slide as template,

mark the outer holes on slide mounting

bracket.

11

2 3

L

1.5 in

L

Side view of inside panel

Desired height

of pants rack

11

Installing the 18”, 24”, 36” Pants Display Rack

Drill holes at the marked locations using

3/16 mm drill bit.

Insert the slide and align the holes with

the drilled holes on the cabinet. Using a

power drill or screw driver fasten the side

mounting slide to the cabinet using four

M5x16mm Screws.

Insert the rack and clip it on the slides.

5

4

6

12

#2 Philips Head

Screw Driver

Pencil

Ø5 x26mm

Melamine Screws

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

X

Tools and parts needed.

Draw a horizontal line on both walls of

the cabinet at distance X from top and

vertical line at distance Y from the back.

Put the bracket on wall and mark holes.

Drill holes at the marked locations on both

walls using 3/16” drill bit.

Fasten one mounting bracket to one side

of cabinet with 5x26mm screws.

1

2

3

Installing the 18” and 24” Closet Rod on Cabinet Walls

X

Side view of inside panel

13

Fix the other bracket to the closet rod.

Align the closet rod and bracket to the

holes marked on the opposite cabinet

wall.

Fasten the bracket to cabinet wall using

two 5x26mm screws.

5

4

6

Installing the 18” and 24” Closet Rod on Cabinet Walls

14

Installing the 18” and 24”Closet Rod on Cabinet Shelf

#2 Philips Head

Screw Driver

Pencil

Ø4 x20mm

Melamine Screws

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

Tools and parts needed.

Draw a centre line on the shelf and mark

two holes at a distance of 16.25 in for 18”

closet rod and 22.25 in for 24” closet rod

from the centre on both sides.

Drill holes at the marked locations using

3/16” drill bit.

Assemble the closet rod and mounting

brackets. Fix the covers of mounting

brackets as shown in the image C.

11

2 3

C

15

Insert the closet rod and align the top

holes with the drilled holes on shelf.

Fasten the closet rod to shelf using two

4x20mm screws.

4

Installing the 18” and 24”Closet Rod on Cabinet Shelf

16

Installing the 18”, 24”, 36” Pull out Hamper Basket

#2 Philips Head

Screw Driver

Pencil

M5 x 16mm

Melamine Screw

#2 Philips Bit

Cordless Drill

(optional)

Level

Drill Bit

3/16”

L

1.5 in

Tools and parts needed.

Draw a horizontal line on the cabinet walls

at desired height (L).

Insert the side mounted slide and align

the rst hole on the slide with the

marked hole position. Use the slide as

template mark the outer holes of the slide

mounting bracket.

1

3

L

Mark a hole at 1.5 in from the front on the

horizontal line.

2

1.5 in

L

Side view of inside panel

Desired height

of drawer slide

17

Installing the 18”, 24”, 36” Pull out Hamper Basket

Take the support frame and adjust the

frame length by adjusting the screws at

the bottom according to the interior of the

cabinet. Make sure to adjust the distance

of the four sides of the frame consistent.

Install frame on the slides. After the frame

is installed, test weather the frame is

sliding smoothly. Lock the four screws at

the bottom of the frame.

2

7

6

Drill holes at the marked locations using

3/16 mm drill bit.

Insert the slide and align the holes with

the drilled holes on the cabinet. Using a

power drill or screw driver fasten the side

mounting slide to the cabinet using four

M5x16mm Screws.

5

4

18

Open the velcro of the clothing bag on four sides, install wire frame under the folds and fold

back the velcro over the wire frame. Connect the plastic holders to with the wire frame as

shown in the image.

Clip the wireframe to the bottom the support frame.

8

9

Installing the 18”, 24”, 36” Pull out Hamper Basket

19

Installing the Under Sink Organizer

#2 Philips Head

Screw Driver

Pencil

M5 x 16mm

Melamine Screw

#2 Philips Bit

M4 x 6mm

Screw

Cordless Drill

(optional)

Level

Drill Bit

3/16”

Tools and parts needed.

1

2.32in

(59mm)

1.40in

(35.5mm)

5.61in

(142.5mm)

3.05in

(77.5mm)

min 3.98in (101mm)

if installed on the left

edge

min 3.98in (101mm)

if installed on the right

edge

SKU #80690

Undersink Organizer

Lay this template

at on the interior

base of the cabinet.

Drill pilot holes

into the marked

locations using a

3/16” drill bit.

Note: Do not drill

through entire cabinet

Ensure the arrows below are aligned with the front edge of the

cabinet and mark the specied locations with a pencil.

Tools Required:

1 x

1 x Pencil

1 x 3/16” Drill Bit

Cordless

Power

Drill

1

3

4

Align the left or

right edge of this

template based on

the space allowed

inside of the

cabinet by local

plumbing.

2

These templates are

designed to drill the

proper mounting

holes for your cabinet

accessories. These

templates are for

NewAge Cabinets and

accessories only.

Place the template on the bottom panel

of cabinet, aligning it to desired location

using template arrows.

1

2.32in

(59mm)

1.40in

(35.5mm)

5.61in

(142.5mm)

3.05in

(77.5mm)

min 3.98in (101mm)

if installed on the left

edge

min 3.98in (101mm)

if installed on the right

edge

SKU #80690

Undersink Organizer

Lay this template

at on the interior

base of the cabinet.

Drill pilot holes

into the marked

locations using a

3/16” drill bit.

Note: Do not drill

through entire cabinet

Ensure the arrows below are aligned with the front edge of the

cabinet and mark the specied locations with a pencil.

Tools Required:

1 x

1 x Pencil

1 x 3/16” Drill Bit

Cordless

Power

Drill

1

3

4

Align the left or

right edge of this

template based on

the space allowed

inside of the

cabinet by local

plumbing.

2

These templates are

designed to drill the

proper mounting

holes for your cabinet

accessories. These

templates are for

NewAge Cabinets and

accessories only.

2.32in

(59mm)

1.40in

(35.5mm)

5.61in

(142.5mm)

3.05in

(77.5mm)

min 3.98in (101mm)

if installed on the left

edge

min 3.98in (101mm)

if installed on the right

edge

SKU #80690

Undersink Organizer

Lay this template

at on the interior

base of the cabinet.

Drill pilot holes

into the marked

locations using a

3/16” drill bit.

Note: Do not drill

through entire cabinet

Ensure the arrows below are aligned with the front edge of the

cabinet and mark the specied locations with a pencil.

Tools Required:

1 x

1 x Pencil

1 x 3/16” Drill Bit

Cordless

Power

Drill

1

3

4

Align the left or

right edge of this

template based on

the space allowed

inside of the

cabinet by local

plumbing.

2

These templates are

designed to drill the

proper mounting

holes for your cabinet

accessories. These

templates are for

NewAge Cabinets and

accessories only.

Remove the template and drill the marked

holes using a 3/16” drill bit.

Mark drill hole locations with a pencil

following template instructions.

32

20

Install rails aligning with the pre marked holes using eight M5x16mm screws.

Slide the centre frame assembly onto the rails by pushing it under the clips at back of the

slides as shown in (A). Secure front portion of the frame to the rails using two M4x6mm screws

as shown in (B).

4

5

A

B

A

Installing the Under Sink Organizer

A

B

La page charge ...

NewAge Products 80642 Guide d'installation

Ce manuel convient également à

NewAge Products 80642 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents