Insignia USB-C VR Headset Cable NS-VR5MCC Mode d'emploi

Insignia
Marque
Insignia
Modèle
USB-C VR Headset Cable NS-VR5MCC
Catégorie
Câbles de signal
Taper
Mode d'emploi

Ce manuel convient également à

PACKAGE CONTENTS
• USB-C VR Headset Cable
• Quick Setup Guide
SYSTEM REQUIREMENTS
Compatible with the Oculus Quest and
Oculus Quest 2 VR headsets
FEATURES
• Designed specically for use with select Oculus
devices, including the Oculus Quest and Oculus
Quest 2
• Durable cable can withstand the physical
demands of full-motion VR devices
• Thin, exible 16.4 ft (5 m) cable with right-angle
connector gives you ample space for movement
while using a VR headset
• Active ber USB-C to USB-C cable provides
full-speed 5 Gbps data transfer for a better
gaming experience
Before using your new product, please read
these instructions to prevent any damage.
USING THE CABLE
1 Plug the 90° end of your cable in to a VR headset,
then connect the other end in to a computer
with a USB-C port.
2 To charge other devices, plug the 90°
end of your cable in to a charging source
(not included), and the other end in to the
selected device with a USB-C port.
Make sure that the device requires
20V/3A (60 W) or less.
Note: This cable can also be used as a standard
USB-C to USB-C cable, however, due to its unique
connector design and construction for use with
VR headsets, there may be compatibility issues in
certain situations.
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
USB-C VR
Headset Cable
NS-VR5MCC
Computer
USB-C devices
Cable
USB-C
connector
NS-VR5MCC_20-0456_QSG_V1_EN_ Final.eps 1 11/18/2020 1:23:22 PM
V1 ENGLISH 20-0456
TROUBLESHOOTING
Charging or data transfer problems
• Make sure that the cable is plugged in securely.
• If your device charges too slowly, make sure
that the device requires less than 20 V at 60 W.
• If your device has a protective covering, the 90°
connector may not make good contact. If the
space surrounding the USB-C port on the device
is limited, the cable may not work. Try using the
straight connector.
SPECIFICATIONS
• Dimensions (length): 16.4 ft. (5 m)
• Data rate: 5 Gbps
• Cable power limit: 20 V/3 A 60 W
About Active Optical Cables (AOC)
Due to the physical properties of copper wires, the speed and length
at high-speed transmission may be limited. In contrast, light signals
suer from much less attenuation in optical bers. Therefore, using a
delivery module to convert electrical signals into optical signals for
transmission in optical bers, and then using a receiving module to
convert the received optical signals into electrical signals can result in
the transmission of higher quality data with longer and thinner
cables. The USB 3.1 high-speed pair of a USB-C optical ber cable uses
optical bers for transmission of data.
SAFETY INFORMATION
• This product can only be used for equipment below 60 W. This is an
optical ber product. It should not be bent 90° for storage, or the
cable could be damaged. Otherwise, it may easily lead to product
damage and dysfunction.
• Do not plug the cable into a non USB-C interface, otherwise the
cable may be damaged
• Remove the cable from the device when it will not be in use for an
extended period of time.
LEGAL NOTICES
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289
(U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
NS-VR5MCC_20-0456_QSG_V1_EN_ Final.eps 2 11/18/2020 1:23:22 PM
  • Page 1 1
  • Page 2 2

Insignia USB-C VR Headset Cable NS-VR5MCC Mode d'emploi

Insignia
Marque
Insignia
Modèle
USB-C VR Headset Cable NS-VR5MCC
Catégorie
Câbles de signal
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents