GE Profile 988423 Guide d'installation

Marque: GE Profile

Modèle: 988423

Catégorie: Lave-vaisselle

Taper: Guide d'installation

READ CAREFULLY

KEEP THESE INSTRUCTIONS

CHECK THE FOLLOWING

 Tub trim does not interfere with the door

 Dishwasher is square and level at both the top and bottom of the cabinet opening,

with no twisting or distortion of the tub or door

 All 4 legs of the dishwasher are firmly in contact with the floor

 Drain hose is not pinched between the dishwasher and adjacent cabinets or walls

 Tub trim is fully seated on the tub flange

WARNING

CAUTION

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS

shown throughout these instructions.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions

for the consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the GE Appliances Warranty. See

Warranty information.

• Completion Time – 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow for future removal from the enclosure if service is

required.

Care should be exercised when the appliance is

installed or removed, to reduce the likelihood of

damage to the power supply cord.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for

available custom panel kits.

Your dishwasher is a water heating appliance.

31-4000211 04-19 GEA

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

• FOR PERSONAL SAFETY: Remove house fuse or open

circuit breaker before beginning installation. Do not use

an extension cord or adapter plug with this appliance.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative if

you are in doubt that the appliance is properly grounded.

• If house wiring is not 2-wire with ground, a ground

must be provided by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

• To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires

are not pinched or damaged, the house wiring is attached

to the junction box bracket through a strain relief, and

all electrical connections made at the time of install (wire

nuts) are contained inside of the junction box cover.

Do not remove wood base until you are ready to install

the dishwasher. The dishwasher will tip over when the

door is opened if base is removed.

While performing installations described in this booklet,

gloves, safety glasses or goggles should be worn.

See your Owner’s Manual for details on how to contact us regarding installation questions

Built-In Dishwashers

Installation

Instructions

PARTS SUPPLIED IN

INSTALLATION PACKAGE:

• Junction box cover and #10 hex-head screw

• Hose clamp

• Drain hose (approximately 58” long)

• Drain hose hanger

• 2 #8-18 hex head screws to secure brackets to

washer tub frame

• 1 top trim piece (on some models)

• 2 side trim pieces

• 2 mounting brackets for wood countertops

or side cabinets

• 2 #8-18 x 5/8” Phillips special head screws,

to secure dishwasher to underside of

countertop or to side cabinets

• Plug buttons

• Literature, samples and/or coupons

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4” and 5/16” nutdriver

• 6” Adjustable wrench

• Level

• Carpenter’s square

• Measuring tape

• Safety glasses

• Flashlight

• Bucket to catch water when flushing the line

• 15/16” socket (optional for skid removal)

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

MATERIALS YOU WILL NEED:

• 90° elbow (3/4”hose internal thread on one

end,opposite end sized to fit water supply)

• UL-listed wire nuts (3)

• Masking Tape

Materials For New Installations Only:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5.4 Ft)

or WX09X70911 (7.9 ft) depending on your installation.

• Hose clamp (if needed for optional drain hose)

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Hot Water Line–3/8” minimum, copper tubing

(including ferrule, compression nut) or GE Appliances

Part # WX28X326, flexible braided hose.

• WD24X10065 drain hose (12’ long), if needed.

Installation Preparation

Hole Saw Set

Measuring Tape

Tubing Cutter

Drill and Bits

Phillips-Head

Screwdriver

15/16” Socket

1/4” and 5/16”

Nutdriver

6” Adjustable

Wrench

Bucket

Flashlight

Gloves

Carpenter’s

Square

Safety Glasses

Level

Drain Hose

Hose Clamp

#8 Hex-Head

Mounting Bracket

Screws

Drain Hose Hanger

Junction

Box Cover

#10

Hex-Head

Junction

Box Screw

1/2" long

Mounting

Brackets

#8 Phillips

Special

Head Screws

5/8" long

Literature

Top Trim Piece

(on some models)

Side Trim Pieces

Pliers

Hot Water Line

Strain Relief

Optional

12' Drain Hose

WD24X10065

Waste Tee

Electrical Cable

(or Power Cord,

if applicable)

Wire Nuts (3)

90°Elbow

Hand

Shut-Off

Valve

Air Gap

Coupler for

optional

drain hose

Plug Buttons

Masking Tape

Hose Clamp

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24” deep,

24” wide and approximately 34-1/2” high from floor to

underside of the countertop.

• The dishwasher must be installed so that drain hose is

no more than 12’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top,

sides and back, and must not support any part of the

enclosure.

CLEARANCES:

• When installed into a corner, allow 2” min. clearance

between dishwasher and adjacent cabinet, wall or other

appliances. Allow 25-1/2” min. clearance from the front of

the dishwasher for door opening. Figure B.

34-1/2”+1/4”

Underside of

Countertop

to Floor

This Wall Area

Must be Free

of Pipes and

Wires

Cabinets

Square

and

Plumb

Plumbing and Electric Service

Must Enter Inside This Area

24”

Min.

4”

6”

24”

Min.

Figure A

33-1/2” to 34-3/4”

Underside of

Countertop

to Floor

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 12’ distance to drain.

• Drain connection height is not to exceed 72” above

bottom of dishwasher.

NOTE : Air gap must be used if waste tee or disposer

connection is less than 18” above floor to prevent

siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18” above floor?

If the answer to either question is YES, Method 1

MUST be used.

•

If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2” diameter hole in the cabinet wall within

the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT – When connecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes

and ordinances. The air gap must be installed according to

manufacturer’s instructions.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed

before attaching dishwasher drain hose to the disposer.

Figure C

Figure B

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-1/2"

To reduce the risk of electric shock, fire, or injury

to persons, the installer must ensure that the

dishwasher is completely enclosed at the time of

installation.

Remove

Drain

Plug

Installation Preparation

WARNING

Figure D

18"

Min.

32"

Min.

Drain Hose Hanger

18"

Min.

32"

Min.

Drain Hose Hanger

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Installation Preparation

For models equipped with power cord: Do not modify the

plug provided with the appliance; if it will not fit the outlet,

have a proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

•

The wiring may enter the opening from either side, rear

or the floor within the shaded area illustrated above in

Figure E and defined in Figure A.

• Cut a 1-1/2" maximum diameter hole to admit the

electrical cable. Edges of hole should be smooth and

rounded. Permanent wiring connections may pass

through the same hole as the drain hose and hot water

line, if convenient. If cabinet wall is metal, the hole

edge must be covered with a bushing.

NOTE:

Power cords with plug must pass through a

separate hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed

as shown in Figure E. Cable must extend a minimum of

24" from the rear wall.

• For power cord connections, install a 3-prong

grounding type receptacle in the sink cabinet rear wall,

6" min. or 18" maximum from the opening, 6" to 18"

above the floor.

• Use only WX09X70910 or WX09X70911 Dishwasher

Power Cord Kit.

PREPARE ELECTRICAL WIRING

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electric

Code, ANSI/NFPA 70 – latest edition, and all local

codes and ordinances.

This appliance must have:

• 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused

electrical supply.

• Wiring must be 2 wire with ground and rated for 75°C

(167°F).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

It is recommended to have:

• A circuit breaker or time-delay fuse.

• A properly grounded individual branch circuit.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

be connected to the equipment-grounding terminal or

lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance

for electric current. This appliance is equipped with a

cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in

accordance with all local codes and ordinances.

Figure E

White

18"

24"

from Wall

from

Cabinet

Alternate Receptacle

Location in Adjacent

Cabinet

Ground

Black

1-1/2" Dia. Hole (Max.)

18"

Receptacle

Location

Area

FOR PERSONAL SAFETY: Remove house fuse or

open circuit breaker before beginning installation.

Do not use an extension cord or adapter plug with this

appliance.

WARNING

The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt that the appliance is properly

grounded.

WARNING

Water Line Connection

• If using a flexible braided supply hose, label

the hose with the installation date to use as

reference. Flexible braided hoses, elbows and

gaskets should be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible

location, such as under the sink. (Optional, but

strongly recommended and may be required by local

codes.)

• Water connection is on the left side of the

dishwasher. Install the hot water inlet line, using no

less than 3/8” copper tubing or a flexible braided

hose. Route the line as shown in Figure F and

extend forward at least 19” from rear wall.

• Adjust water heater for 120°F to 140°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120

PSI.

Turn page to begin dishwasher

installation.

Installation Preparation

PREPARE HOT WATER LINE

NOTE: GE Appliances recommends copper tubing for

the water line, but if you choose to use flexible hose,

use GE Appliances WX28X326, flexible braided hose.

• The water supply line (3/8” copper tubing or flexible

braided hose) may enter from either side, rear or

floor within the shaded area shown in Figure F.

• The water supply line may pass through the same

hole as the electrical cable and drain hose. Or, cut

an additional 1-1/2" diameter hole to accommodate

the water line. If power cord with plug is used, water

line must not pass through power cord hole.

Figure F

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

From

Cabinet

Hot

1-1/2”

Dia.

Hole

Do not remove wood base until you are ready to

install the dishwasher. The dishwasher will tip over

when the door is opened if base is removed.

CAUTION

STEP 1

PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Mounting brackets

• Trim pieces (on some models)

• Drain hose hanger

• Owner’s Manual

• Product samples and/or coupons

Dishwasher Installation

STEP 3

REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT – Do not kick off wood base!

Damage will occur.

• Move the dishwasher close to the installation location

and lay it on its back. NOTE: Do not place the

dishwasher on its side.

• Remove the 4 leveling legs on the underside of the

wood base with a 15/16” socket wrench.

• Discard base.

• On models without the center bottom adjustable

leveling system:

Screw leveling legs back into the dishwasher frame,

approximately 1/2” from frame as shown.

• On models with the center bottom adjustable

leveling system:

Screw front leveling legs back into dishwasher frame

approximately 1/2”.

Screw rear leveling legs completely in until fully seated.

CHECK DOOR BALANCE

NOTE: If installing a

Custom Door Panel

(available on some

models), please

follow the instructions

found in the Custom

Door Panel kit

WD35X20417.

• With dishwasher

on the wood base,

check the door

balance by opening

and closing the door.

• Door is properly balanced if, when opened, it self

closes within 20° from vertical, stays in position from

20° to 70° and falls fully open beyond 70°.

• If necessary increase or decrease tension as shown.

Some models will have 2 springs on one side and

1 spring on the other side. Latch door and adjust

springs to correct balance.

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open

easily or falls too quickly, check spring cable routing.

The cable is held in place by “shoulders” on the pulley.

Check to be sure cable has not slipped over the pulley

shoulders and is routed as shown.

Figure G

Door

closes

within

20°

Door stays in

position from

20° to 70°

Door falls fully

open beyond 70°

Side View

Figure G

Figure H

Side View

Custom

door

panel

Spring

hooked

to hole

inside rail

NOTE: The number of

springs, on each side,

will vary by model.

Front View

Make sure pully

cables are within

pulley shoulders

Increase

Tension

Decrease

Tension

STEP 2

Approx

1/2"

Replace all 4 legs

to about 1/2” from

the frame

Remove all four

leveling legs and

the wood base

Appearance will vary

Replace 2

front legs

to about

1/2” from

the frame

Replace

2 back

legs and

screw in

completely

Leveling System

To be adjusted

later in Step 14.

1/2”

STEP 7

INSTALL DRAIN HOSE TO

DRAIN LOOP

Connect drain loop end to drain hose using the clamp

as shown in the figure.

NOTE: The high drain loop on the side of the tub is

designed for better wash performance. Do not remove

from the side of the tub.

STEP 8

POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the

floor of the opening to avoid interference with base

of dishwasher and components under dishwasher.

STEP 9

INSTALL DRAIN HOSE,

THROUGH CABINET

• Position dishwasher in front of cabinet opening,

and if present, dislodge drain hose from drain hose

clip. Insert drain hose into the hole in cabinet side.

If a power cord is used, guide the end through a

separate cabinet opening.

Tip: Prevent unnecessary service call charges for

fill, drain or noise concerns.

Position utility lines so they do not interfere with

anything under or behind the dishwasher.

Dishwasher Installation

STEP 5

FLOOR PROTECT PAN

(On some models)

• Pan should not be removed during installation.

STEP 6

INSTALL 90° ELBOW

• Thread 90° elbow

onto the water valve.

Ensure rubber gasket

is located between

valve and elbow.

• Do not overtighten

elbow. Water valve

bracket could bend

or water valve fitting

could break.

• Position the end

of the elbow to

face the rear of the

dishwasher.

Figure O

Water

Line

House

Wiring

Figure M

Water

Valve

Bracket

Fill Hose

Front of dishwasher

90° Elbow

House

Wiring

Power Cord

(If used)

Drain

Hose

Water

Line

Insulation

Blanket

Ensure drain hose is not

twisted or pinched

Maximum drain hose

length is 15'

Do not disconnect or remove high

drain loop from left side of dishwasher

Pull insulation

blanket over

collar

Figure P

REMOVE TOEKICK

• Remove the 2

toekick screws

and toekick.

Set aside for

use in Step 22.

STEP 4

Toekick

Remove 2

Toekick Screws

Do not

remove

pan

INSTALL TRIM PIECES

In this step you will need the trim pieces set aside in Step 1.

• Select the top trim piece (See Figure R) and line up

center to the top latch. Press the trim piece onto the

tub flange moving from one side to the other.

• Select the left trim piece (see Figure R). Align top

edge with the top trim and press it onto the left side

of the tub flange moving from the top to the bottom.

Repeat for the right side tub flange trim piece. (See

Figure R for right side trim piece.)

Dishwasher Installation

SLIDE DISHWASHER

THREE-FOURTHS OF

THE WAY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

•

Grasp the sides of the front panel and slide

dishwasher into the opening a few inches at a time.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the

dishwasher extends about 6 inches forward of

adjacent cabinets.

• Make sure drain hose is not kinked under or behind

the dishwasher.

• Make certain the house wiring, drain line and

water line do not interfere with components under

dishwasher.

STEP 10

Figure Q

Do not push against

front door panel with

knee. Damage to the

door panel will occur.

Top

View

Handle

Door

Tub trim

Tub frame

STEP 11

Side Trim

Figure R

Side

Trim

Top View

Side

Trim

Top Trim

Fully seat to tub flange

Dishwasher Installation

INSTALL MOUNTING

BRACKETS

You will need the mounting brackets and 2 #8 hex-

head screws set aside in Step 1.

You must install the mounting brackets onto the

dishwasher tub frame top or sides prior to sliding

the dishwasher into place under the countertop. This

dishwasher is capable of a true-flush installation at a

24” deep opening. The mounting brackets have several

available attachment positions to accommodate different

cabinet constructions.

Install mounting brackets on top if the

underside of countertop is wood or wood-like

material that accepts screws:

IMPORTANT - After installing brackets and before

closing the dishwasher door, adjust the brackets

by bending them up as needed, so that they do not

contact the top of the dishwasher door and cause

damage.

•

If you are installing the dishwasher under a counter

with a short overhang, the countertop brackets may

extend beyond the edge of the counter. If this is

the case, remove the excess length by repeatedly

bending the brackets at the front notch only until they

break.

PUSH DISHWASHER INTO

FINAL POSITION

•

Check the tub insulation blanket, if equipped, to be

sure it is smoothly wrapped around the tub. It should

not be “bunched up” and it must not interfere with

the door springs. If the insulation is “bunched up” or

interfering with the springs, straighten and re-center

the blanket prior to sliding the dishwasher into its

final position.

•

Slide the dishwasher into the final position by

pushing on the sides of the door panel. Do not push

or pull the door in a partially open or closed position

when moving the dishwasher. Do not use a knee or

push on the center of the panel. If you do, damage to

the panel will likely result. Check that the dishwasher

is squarely positioned in the cabinet opening at

both the top and the bottom of the appliance prior to

mounting to the cabinet.

IMPORTANT – Before opening the dishwasher door,

be certain the edges of the dishwasher door panel

are behind the face of the adjacent cabinet and not

up against the cabinet face. Refer to Figure U. If the

dishwasher door is opened when the edge of the door

is against the face of the cabinet, dishwasher door

damage and cabinet damage will occur.

STEP 12

INSTALL MOUNTING

BRACKETS (CONT.)

Install mounting brackets on sides if the

countertop is granite or similar material that will

not accept wood screws:

• If present, remove drain hose clip from collar and

dispose.

•

Break off front portion of the tab with pliers at the

location shown prior to attaching to dishwasher.

•

Position the left-hand side bracket as shown. Attach

the bracket to the tub frame with the #8 screw through

the slotted hole below the round hole. Repeat with the

right bracket.

STEP 12

Figure T

Bracket

Dishwasher

tub frame

#8 Bracket

screw as

supplied

Side Mounting

Bend and break

here if necessary

Care should be taken

to ensure mounting

screws do not damage

cabinetry

Do not pinch the

latch wires in #8

bracket screw

Remove

this clip

Tub

Front

STEP 13

#8 Bracket

Screw

Bracket

Bend and break here

after installing if counter

has a short overhang.

Top Mounting

Figure S

Tub

Front

Dishwasher

tub frame

Dishwasher Installation

PUSH DISHWASHER

INTO

FINAL POSITION (CONT.)

•

Open and close the dishwasher door to be sure it

operates smoothly, and does not rub on the adjacent

cabinet.

Tip: Prevent unnecessary service charges for

panel damage or wash performance.

Check dishwasher alignment prior to opening

dishwasher door to prevent panel damage.

Make sure utility lines are not trapped or crushed behind

dishwasher. Crushed lines will restrict water flow.

LEVEL DISHWASHER

(CONT.)

•

Remove the lower dish

rack and place a level on

the door and lower rack

track as shown in figure.

If your model has a rear leveling system, the rear height

is adjusted from the front of the dishwasher along with the

2 front legs on the bottom of the dishwasher. Begin the

leveling process with the front legs by individually turning the

front 2 legs. Adjust the front legs first. When the front legs

are adjusted to a height resulting in an appropriate gap to

the upper cabinet, proceed to adjust the rear leveling system

by adjusting the leveling bolt as illustrated in the figure.

Turn the bolt to adjust the rear leveling system. Slowly rotate

the bolt clockwise to raise the back of the dishwasher, and

counterclockwise to lower it. Continue to adjust the feet until

the dishwasher is level as illustrated in the figure. Ensure all 3

legs are firmly in contact with the floor.

If your model has 4 leveling feet, adjust the

level of the dishwasher by individually turning

the 4 legs on the bottom of the dishwasher

as shown in figure.

•

The dishwasher is properly leveled when the level indicator is

centered left to right and front to back. Also, the dishwasher

door should close without hitting the side of the tub.

• Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify

dishwasher is leveled.

Pull the dish racks half way out. They should stay put. Open

and close the door. The door should fit in the tub opening

without hitting the side of the tub. If the racks roll on their

own, or the door hits the side of tub, re-level the dishwasher.

STEP 13 STEP 14

LEVEL DISHWASHER

IMPORTANT – Dishwasher must be level for proper dish

rack operation, wash performance and door operation. The

dishwasher must be leveled left to right and front to back.

This ensures the dish racks will not roll in or out on their own,

circulation water will flow to the pump inlet, and the door will

close without hitting the side of the tub.

STEP 14

Figure U

Door Catches

on Cabinet Frame

Correct

Alignment

Incorrect Alignment

will result in door damage

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Check that tub trim does not

contact the door at all points

Tub trim may be trimmed if

necessary to ensure proper

door operation

Top

View

Handle

Door

Tub trim

Tub frame

Do not allow tub trim to get

trapped by or come into

contact with the door

Top

View

Tub trim

trapped

by door!

Cabinet

Turn front

leg to adjust

front height

Turn leveling system

bolt to adjust rear height

Turn front

leg to adjust

front height

Dishwasher Installation

POSITION DISHWASHER,

SECURE TO COUNTERTOP

OR CABINET

In this step you will need the 2 Phillips special head

screws from the screws set aside in Step 1.

The dishwasher must be secured to the countertop

or the cabinet sides. When the underside of the

countertop is wood, use Method 1. Use Method 2

when the underside of the countertop is made of a

material, such as granite, that will not accept wood

screws.

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so

the front panel and control panel do not contact the

adjacent cabinets or countertop. Mounting screws

must be driven straight and flush. Protruding screw

heads could scratch the door panel or control panel

and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

• Recheck alignment of the dishwasher in the cabinet.

Refer to Steps 13 and 14. Door panel and/or control

panel must not hit cabinets or countertop.

• Fasten the dishwasher to the underside of the

countertop with the 2 Phillips special head screws.

Refer to figure. Make certain screws are driven

straight and flush to prevent panel damage.

Method 2

Secure dishwasher to cabinet sides.

• Recheck alignment of the dishwasher in the cabinet.

Refer to Steps 13 and 14. Door panel and/or control

panel must not hit cabinets or countertop.

• Remove plug buttons. Do not discard.

• Fasten the dishwasher to the adjacent cabinets with

the 2 Phillips special head screws provided. Refer

to Figure X. Make certain screws are driven straight

and flush to prevent panel damage. Do not screw

into the cabinet face frame.

• Install plug buttons to the side of the tub in the holes

provided.

CONNECT WATER

SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

• Attach nut to 90° elbow using an adjustable wrench.

If using a copper tubing connection:

•

Slide compression nut, then ferrule over end of water

line.

• Insert water line into 90° elbow.

•

Slide ferrule against elbow and secure with

compression nut.

IMPORTANT – Check to be sure that door spring and/

or door spring cable do not rub or contact the fill hose

or water supply line. Test by opening and closing the

door. Re-route the water supply lines if a rubbing noise

or interference occurs.

Brackets

Wood Countertop

Figure X

Solid Surface Countertop

Side Brackets

Plug buttons

Screw

Figure Y

Compression

Nut

Hot Water

Supply Line

90° Elbow

Ferrule

Bottom Left Side

STEP 15

POSITION DISHWASHER,

SECURE TO COUNTERTOP

OR CABINET (CONT.)

• Re-check that the dishwasher is square and level at

both the top and bottom of the cabinet opening, with no

twisting or distortion of the tub or door after mounting to

the cabinets/countertop. Adjust if necessary.

• Confirm all leveling legs are in contact with the floor

to prevent the dishwasher from rocking and ensure

proper door and latch operation.

STEP 15

STEP 16

CONNECT DRAIN LINE

(CONT.)

• Connect drain line to air gap, waste tee or disposer

using the previously determined method. Secure

hose with a screw-type clamp.

Method 1 – Air gap with waste tee or disposer

Method 2 – “High drain loop” with waste tee or

disposer

With this method you will need the drain hose hanger

set aside in Step 1.

Fasten drain hose to underside of countertop with the

provided hanger.

IMPORTANT – When connecting drain line to

disposer, check to be sure that drain plug has been

removed. DISHWASHER WILL NOT DRAIN IF PLUG

IS LEFT IN PLACE.

Tip: Avoid unnecessary service call charges for a

no drain complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose

in the dishwasher cavity from becoming kinked or

crushed by the dishwasher.

Dishwasher Installation

Remove

Drain

Plug

CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8” through 1”

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose connector on the marked line, if required,

to fit the inlet port.

• If a longer drain hose is required, replace the

provided user bag drain hose with GE Appliances

service part WD24X10065, a 12’ long hose which

can be connected directly to the drain loop already

attached to the unit (see Step 7). If service part hose

is not available, an additional hose with coupler, ID of

5/8” or 7/8” and no longer than 66”, may be attached

to the provided user bag drain hose. Secure the

connection with hose clamp (obtain locally) to the

provided user bag drain hose.

NOTES:

• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED

72” ABOVE BOTTOM OF DISHWASHER.

• TOTAL DRAIN HOSE LENGTH MUST NOT

EXCEED 12 FEET FOR PROPER DRAIN

OPERATION.

Figure Z

Cutting Line

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

STEP 17 STEP 17

Hose

Clamp

Coupler Hose

Clamp

Figure AA

Figure AB

Disposer Installation

Waste Tee Installation

Figure AC

18"

Min.

32"

Min.

32"

Min.

18"

Min.

Drain Hose Hanger

Disposer Installation

Dishwasher Installation

CONNECT POWER SUPPLY

If a power cord with plug is already installed

proceed to Step 19.

In this step you will need the junction box cover and

the #10 Hex head screw from the screws set aside in

Step 1.

• Secure house wiring to the back of the junction box

with a strain relief.

• Locate the 3 dishwasher wires, (white, black and

green) with the stripped ends coming out of the AC

jumper. Use UL listed wire nuts of appropriate size to

connect incoming ground to green, white to white and

black to black.

• Install the junction box cover using #10 hex head

screw. Check to be sure that wires are not pinched

under the cover.

• Make sure that the junction box cover is resting on

the mounting bracket.

• If using a Power Cord Kit, use GE Appliances part

number WX09X70910 or WX09X70911 and refer to

the included instructions.

Figure AD

Ground

(Green)

NOTE: Do not remove the

Junction Box Bracket.

Jumper

Junction Box

Bracket

Black

White

Ground Screws

NOTE: All ground screws, brackets and wires must

remain intact.

If house wiring is not 2-wire with ground, a ground

must be provided by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

WARNING

STEP 18

PRETEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper

packaging.

• Locate the Owner’s Manual set aside in Step 1.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not

open and close freely, check for proper routing of

spring cable over pulley. If door drops or closes

when released, adjust spring tension. See Step 2.

• Check to be sure that wiring is secure under the

dishwasher, not pinched or in contact with door

springs or other components. See Step 18.

• Check door alignment with tub. If door hits tub, level

dishwasher. See Step 14.

• Check door alignment with cabinet. If door hits

cabinet, reposition dishwasher. See Step 13.

• Check that door spring does not contact water line,

fill hose, wiring or other components. See Step 13.

• Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise.

• Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be

between 120°F and 140°F. A minimum of 120°F

temperature is required for best wash performance.

See “Prepare Hot Water Line,” page 5.

• Add 1 quart of water to the bottom of the dishwasher

to lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten

connections if needed.

• Remove protective film if present from the control

panel and door.

• Check that tub trim does not contact the door.

STEP 19

Dishwasher Installation

DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,

if equipped.

• Select a cycle to run and push the Start pad.

• Ensure the door is latched. Dishwasher should start.

• Check to be sure that water enters the dishwasher.

If water does not enter the dishwasher, check to be

sure that water and power are turned on.

• Check for leaks under the dishwasher. If a leak

is found, turn off power at the breaker, and then

tighten water connections. Restore power after leak

is corrected.

NOTE: A small amount of water may splash out of

the fill funnel, on the right side of the tub, during the

first use after installation. Splash-out is most likely to

occur if there is air in the water supply line from new

construction or if the valve has been closed for an

extended time.

• Check for leaks around the door. A leak around

the door could be caused by door rubbing or

hitting against adjacent cabinets. Reposition the

dishwasher if necessary. See Step 13.

• Press and hold the Start pad for 3 seconds to

cancel the cycle. The unit will begin to drain. Check

drain lines. If leaks are found, turn off power at the

breaker and correct plumbing as necessary. Restore

power after corrections are made. See Steps 7, 8, 9,

10 and 17.

• Open dishwasher door and make sure all of the

water has drained. If not, check that disposer plug

has been removed and/or air gap is not plugged.

Also check drain hose to be sure it is not kinked

underneath or behind dishwasher. See Step 17.

• Press Start pad once again and run dishwasher

through another cycle. Check for leaks and correct if

required.

• Repeat these steps as necessary.

STEP 20

POSITION SOUND

INSULATION PIECE

(on some models)

• Locate the sound insulation package inside the

dishwasher.

• Stand the parts upright as shown.

• Locate the control box.

• Push insulation block portion under the dishwasher

until it is beneath the control box.

• Push the panel portion up to the front of the block.

• Tuck the sides of the front panel behind the toekick

attachment screw holes.

Control Box

Figure AH

STEP 21

Push the sides of the insulation behind the toekick

attachment screw holes

(on some models)

Toekick

Insulation Block

(On some models.)

Dishwasher

Door

Dishwasher Installation

LITERATURE

• Be sure to leave complete literature package, these Installation

Instructions and product samples and/or coupons with the

consumer.

REPLACE TOEKICK

• Place toekick against the legs of the dishwasher.

• Align the toekick with the bottom edge and make

sure it is against the floor.

• Insert and tighten the 2 toekick attachment screws.

The toekick should stay in contact with the floor.

Tip: Reduce sound from under the dishwasher.

Make sure toekick is against floor.

Figure AJ

Attachment

Screws

Toekick

CHECK THE FOLLOWING

• Tub trim does not interfere with the door

• Dishwasher is square and level at both the top and

bottom of the cabinet opening, with no twisting or

distortion of the tub or door

• On models without the adjustable leveling system,

make sure all 4 legs of the dishwasher are firmly in

contact with the floor

• On models with the adjustable leveling system, make

sure both front legs of the dishwasher and the center

rear leveling system leg are firmly in contact with the

floor

• Drain hose is not pinched between the dishwasher

and adjacent cabinets or walls

• Tub trim is fully seated on the tub flange

STEP 22

STEP 23

STEP 24

NOTE: Product improvement is a continuing endeavor. Therefore, materials, appearance and specifications are subject to change without notice.

VEUILLEZ LIRE ATTENTIVEMENT

CONSERVER CES DIRECTIVES

VÉRIFIEZ LES POINTS SUIVANTS

 La moulure de la cuve ne gêne pas la porte

 Le lave-vaisselle est d'équerre et de niveau par rapport au

bas et au haut de l'ouverture de l'armoire, sans torsion ni

déformation de la cuve ou de la porte

 Les quatre (4) pieds reposent fermement sur le plancher

 Le boyau de vidange n'est pas coincé entre le lave-

vaisselle et les armoires ou les murs adjacents

 La moulure de cuve repose entièrement contre le bord

de la cuve

ARRÊT

POUR VOTRE SÉCURITÉ

Veuillez lire et observer toutes les mises en garde

AVERTISSEMENT et ATTENTION données dans les

présentes directives.

IMPORTANT – Observez tous les codes et

ordonnances en vigueur.

• Note à l’installateur – Veuillez laisser les présentes

directives au consommateur pour l’inspecteur local.

• Note au consommateur – Veuillez conserver les

présentes directives avec votre Manuel d’utilisation

pour consultation ultérieure.

• Compétences requises – L’installation de ce

lave-vaisselle exige des compétences de base en

mécanique, en électricité et en plomberie.

L’installateur est responsable de la qualité

de l’installation. Toute défaillance du produit

attribuable à une installation inadéquate n’est

pas couverte par la Garantie de GE Appliances.

Reportez-vous à la Garantie du produit.

• Durée de l’installation – Entre 1 et 3 heures.

L’installation d’un nouveau lave-vaisselle exige plus de

temps que le remplacement d’un ancien modèle.

IMPORTANT – Le lave-vaisselle DOIT être installé de

manière à ce qu’il puisse être sorti de son emplacement

si des réparations sont nécessaires.

Il importe d'user de prudence lorsque l'appareil est

installé ou déplacé afin de prévenir l'endommagement

du cordon d'alimentation.

Si le lave-vaisselle que vous avez reçu est endommagé,

communiquez immédiatement avec votre détaillant ou

l’entrepreneur en construction.

Accessoires facultatifs – Reportez-vous au Manuel

d’utilisation pour connaître les ensembles pour panneau

décoratif personnalisé offerts.

Votre lave-vaisselle est un appareil qui chauffe l’eau.

• Pour réduire les risques de choc électrique, d’incendie ou de

blessures, l’installateur doit s’assurer que le lave-vaisselle

est complètement encastré au moment de l’installation.

• POUR VOTRE SÉCURITÉ PERSONNELLE: Enlevez

le fusible ou déclenchez le disjoncteur au panneau

de distribution principal avant de commencer

l’installation. N’utilisez pas une rallonge électrique ou

un adaptateur de fiche avec cet appareil.

• Un branchement inadéquat du conducteur de

mise à la terre peut présenter des risques de choc

électrique. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

réparateur ou un électricien qualifié.

• Si le câblage électrique de la résidence n’est pas

constitué de deux fils plus un fil de mise à la terre,

l’installateur doit installer un fil de mise à la terre. Si le

câblage électrique de la résidence est en aluminium,

utilisez un agent antioxydant et des connecteurs pour

raccords «aluminium-cuivre» homologués UL.

• Pour réduire les risques de choc électrique, d’incendie

ou de blessures, l’installateur doit vérifier pour s’assurer

que les fils ne sont pas pliés ou en dommagés, que

le câblage domestique est fixé au support de boîte

de connexion par l’entremise d’un serre-câble et que

toutes les connexions électriques faites au moment de

l’installation (capuchons de connexion) se trouvent

à l’intérieur du couvercle de la boîte de connexion.

N’enlevez pas la base de bois avant d’être prêt à installer

le lave-vaisselle. Si vous enlevez la base de bois, le lave-

vaisselle pourrait basculer lorsque vous ouvrez la porte.

Pour effectuer l’installation décrite dans les

présentes directives, il faut porter des gants et

des lunettes de sécurité.

AVERTISSEMENT

ATTENTION

AVANT DE COMMENCER

Veuillez lire attentivement toutes les directives qui suivent.

31-4000211 04-19 GEA

Instructions

D’Installation

Lave-vaisselle encastré

Consultez votre Manuel du Propriétaire pour plus de détails sur la façon de nous contacter concernant les

questions d’installation

OUTILS NÉCESSAIRES:

• Tournevis cruciforme

• Tournevis à douille de 5/16 po et 1/4 po

• Clé à molette de 15 cm (6 po)

• Niveau

• Équerre de menuisier

• Ruban à mesurer

• Lunettes de sécurité

• Lampe de poche

• Seau pour attraper l’eau lors de la purge du tuyau

• Douille de 15/16 po (optionnelle pour

la dépose de la palette)

• Gants

• Pince

Pour une nouvelle installation:

• Coupe-tube

• Perceuse et mèches appropriées

• Jeu de scie-cloche

MATÉRIAUX NÉCESSAIRES:

• 90°, bague et écrou à compression (boyau avec filetage interne

19,1 mm [3/4 po] à une extrémité et de dimension adaptée à

la conduite d’alimentation à l’autre extrémité)

• Connecteurs vissables homologués UL (3)

• Ruban-cache

Pour une nouvelle installation:

• Coupure anti-refoulement pour le boyau de vidange, si nécessaire

• Raccord en T pour la plomberie de la résidence, s’il y a lieu

•

Câble électrique ou Trousse de cordon d’alimentation

WX09X70910 (5,4 pi) ou WX09X70911 (7,9 pi) en fonction de

votre installation.

• Collier (si nécessaire pour boyau de vidange optionnel)

• Bague anti-traction pour le raccordement électrique

• Robinet d’arrêt (recommandé)

• Conduite d’eau chaude – 9,5 mm (3/8 po) minimum, tuyau en

cuivre (incluant la bague et l’écrou à compression) ou la pièce

WX28X326 de GE Appliances, boyau métallique flexible.

• Boyau de vidange de 3,7 m (12 pi) de long WD24X10065,

si nécessaire

PIÈCES FOURNIES DANS

L’EMBALLAGE:

• C

ouvercle de la boîte de jonction et vis à tête hexagonale n° 10

• Collier

• Boyau de vidange (147 cm/58 po de long)

• Support de tuyau de vidange

• 2 Vis à tête hexagonale no 8-18 pour fixer les

supports au cadre de la cuve du lave-vaisselle

• 1 Garniture supérieure (certains modèles)

• 2 Moulures latérales

• 2 Supports de montage pour comptoirs ou

armoires latérales en bois

• 2 Vis à tête spéciale Phillips n° 8-18 x 15,8 mm (5/8 po) pour fixer

le lave-vaisselle au dessous du comptoir ou armoires latérales

• 2 Boutons de bouchon

• Documentation, échantillons et(ou) bons

Préparation pour l’installation

Scie-cloche

Ruban à mesurer

Coupe-tube

Perceuse et

mèches

Tournevis

cruciforme

Douille de 15/16

Tournevis à douille

de 5/16 po et 1/4 po

Clé à molette de

15 cm (6 po)

Seau

Lampe de poche

Gants

Équerre de

menuisier

Lunettes de sécurité

Niveau

Boyau de vidange

Vis à tête spéciale

Phillips n° 8

de 15,8 mm (5/8 po)

de long

Vis à tête

hexagonale n° 10

de 12,7 mm (1/2

po) de long pour

boîte de jonction

Collier

Couvercle de la

boîte de jonction

et vis à tête

hexagonale n° 10

Supports de

montage

Support de tuyau

de vidange

Vis à tête hexagonale

n° 8 pour support de

montage

Documentation

Garniture (supérieure)

(certains modèles)

Moulures latérales

Coupure anti-

refoulement

Bague

anti-traction

Raccord

en T

Câble électrique (ou

cordon d’alimentation,

s’il y a lieu)

Connecteurs

vissables (3)

Robinet

d’arrêt

Coude de 90°

Conduite d’eau

chaude

Pince

Raccord pour

boyau de vidange

facultatif

Boutons de

bouchon

Ruban-cache

Collier

Boyau de

vidange facultatif

(optionnel)

WD24X10065

PRÉPARATION DE L’OUVERTURE

DANS LES ARMOIRES

• L’ouverture dans les armoires doit mesurer au moins 61,0 cm (24

po) de largeur et de profondeur, et environ 87,6 cm (34-1/2 po)

de hauteur à partir du plancher jusqu’au-dessous du comptoir.

• Le lave-vaisselle doit être installé de façon à ce que le boyau

de vidange mesure au maximum 3.66 mètres (12 pieds) pour

assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent être

complètement dissimulés à l’intérieur de l’ouverture. Le lave-vaisselle

ne doit soutenir aucune partie de la structure des armoires.

DÉGAGEMENTS:

• Dans le cas d’une installation dans un coin, veuillez prévoir

un dégagement d’au moins 5,1 cm (2 po) entre le lave-

vaisselle et les armoires, le mur ou un électroménager

adjacent. Veuillez prévoir un dégagement d’au moins 65 cm

(25-1/2 po) à l’avant du lave-vaisselle pour l’ouverture de la

porte. Reportez-vous à la Figure B.

Préparation pour l’installation

Figure A

33-1/2 po to 34-3/4

po du dessous

du comptoir au

plancher

Le mur du fond

doit être exempt

de tuyaux ou

de fils

La partie ombrée est

réservée à la plomberie et

à l’électricité

Armoires à

l’équerre et

d’aplomb

61,0 cm

(24 po) min.

15,2 cm (6 po)

61,0 cm

(24 po) min.

10,1 cm

(4 po)

Comptoir

Lave-vaisselle

5,1 cm (2 po) minimum

pour l’ouverture de la porte

65 cm (25-1/2 po)

Figure B

EXIGENCES RELATIVES AU

SYSTÈME DE VIDANGE

• Veuillez observer les ordonnances et les codes locaux en vigueur.

• Le boyau de vidange doit avoir une longueur maximale de 3.66

mètres (12 pieds).

• Le boyau de vidange ne doit pas être raccordé à une hauteur

dépassant 1,8 m (72 po) au-dessus du bas du lave-vaisselle.

REMARQUE: Il faut installer une coupure anti-refoulement si le

raccord au broyeur à déchets ou au raccord en T se trouve à moins

de 46 cm (18 po) au-dessus du plancher afin d’éviter un siphonage.

CHOIX DE LA MÉTHODE DE VIDANGE

Le type d’installation de vidange dépend des conditions suivantes.

• Les ordonnances ou codes locaux en vigueur exigent-ils une

coupure anti-refoulement?

• Le raccord T se trouve-t-il à moins de 46cm (18po) du plancher?

Si vous répondez OUI à l’une ou l’autre de ces

questions, vous DEVEZ utiliser la méthode n° 1.

• Si vous répondez NON, vous pouvez employer l’une ou l’autre

des méthodes.

PRÉPARATION DES ARMOIRES

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la paroi de

l’armoire qui se trouve dans la partie ombrée de la Figure A pour

le boyau de vidange. Assurez-vous que l’orifice ne présente pas

d’arêtes vives.

IMPORTANT – Lorsque vous branchez le boyau de vidange

à un broyeur à déchets, assurez-vous

d’enlever le bouchon de vidange. LE

LAVE-VAISSELLE NE POURRA PAS

SE VIDER SI VOUS LAISSEZ LE

BOUCHON EN PLACE.

Méthode n° 1 – Coupure anti-refoulement avec raccord en

T ou broyeur à déchets

Il faut installer une coupure anti-refoulement lorsqu’elle est exi-

gée par les ordonnances et les codes locaux en vigueur. Cette

coupure anti-refoulement doit être installée conformément aux

directives données par le fabricant.

Méthode n° 2 – Boucle de vidange élevée avec raccord en

T ou broyeur à déchets

Conseil: Pour éviter des frais de réparation inutiles.

Assurez-vous d’enlever le bouchon de vidange du broyeur à

déchets avant d’y brancher le boyau de vidange du lave-vaisselle.

Pour réduire les risques de choc électrique, d’incendie

ou de blessures, l’installateur doit s’assurer que le

lave-vaisselle est complètement encastré au moment

de l’installation.

AVERTISSEMENT

Figure C

Figure D

18"

Min.

32"

Min.

18"

Min.

32"

Min.

Crochet pour boyau de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Crochet pour boyau

de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Remove

Drain

Plug

Enlevez le

bouchon

de vidange

Préparation pour l’installation

Figure E

Zone pour

la prise de

courant

Autre emplacement

possible pour la prise

de courant dans une

armoire adjacente

46 cm (18 po)

46 cm

(18 po)

15 cm (6 po)

15 cm

(6 po)

Trou de 3,8 cm

(1-1/2 po) de dia.

(max.)

7,6 cm (3 po)

des armoires

61 cm (24

po) du mur

Mise à la terre

Noir

Blanc

POUR VOTRE SÉCURITÉ PERSONNELLE: Enlevez

le fusible ou déclenchez le disjoncteur au panneau

de distribution principal avant de commencer

l’installation. N’utilisez pas une rallonge électrique ou

un adaptateur de fiche avec cet appareil.

AVERTISSEMENT

Un branchement inadéquat du conducteur de

mise à la terre peut présenter des risques de choc

électrique. Si vous n’êtes pas certain que l’appareil est

correctement mis à la terre, consultez un réparateur

ou un électricien qualifié.

AVERTISSEMENT

ALIMENTATION ÉLECTRIQUE

Assurez-vous que le branchement électrique et le

calibre du fil sont adéquats et conformes avec la version

récente de la norme ANSI/NFPA 70, le Code national de

l’électricité, tous les règlements et toutes les ordonnances

de votre région.

L’alimentation électrique de cet appareil doit être :

• 120 V, 60 Hz, en courant alternatif seulement, avec un

fusible de 15 ou 20 A.

• Le câble électrique doit posséder deux fils, plus un fil de

mise à la terre, et résister à une température nominale de

75 °C (167 °F).

• Si votre alimentation électrique ne répond pas à ces

exigences, appelez un électricien agréé avant de

poursuivre l’installation.

Nous recommandons d’avoir :

• Un disjoncteur ou fusible temporisé.

• Un circuit de dérivation individuel mis à la terre approprié.

Mise à la terre – Branchement permanent

Cet appareil doit être branché à un réseau électrique

permanent mis à la terre. Sinon, il faut installer un

conducteur de mise à la terre avec les conducteurs du

circuit et le brancher à la borne de mise à la terre du

réseau ou au fil de mise à la terre de l’appareil.

Mise à la terre – Modèles dotés d’un cordon

d’alimentation

Cet appareil doit être mis à la terre. En cas de mauvais

fonctionnement ou de défaillance, la mise à la terre réduira

les risques de choc électrique en fournissant au courant

électrique un circuit de moindre résistance. Cet appareil est

doté d’un cordon d’alimentation possédant un conducteur

de mise à la terre et une fiche de mise à la terre. La fiche

doit être branchée dans une mise appropriée, installée et

mise à la terre en conformité avec tous les codes locaux et

ordonnances en vigueur.

Dans le cas des modèles dotés d’un cordon

d’alimentation:

Ne modifiez pas la fiche fournie avec l’appareil; si vous ne

pouvez pas la brancher dans la prise de courant, faites

installer une prise de courant appropriée par un technicien

qualifié.

Préparation des armoires et cheminement des fils

• Les fils peuvent entrer dans l’ouverture du côté droit, du

côté gauche, de l’arrière ou du plancher dans la partie

ombrée de la Figure E et de la Figure A.

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre au

maximum pour le passage du câble électrique. Le bord du

trou doit être lisse et arrondi. Les fils électriques pour le

branchement permanent peuvent passer par le même trou

que le boyau de vidange et la conduite d’eau chaude, si

c’est plus pratique. Si le trou est pratiqué dans une paroi

en métal, les bords de l’orifice doivent être recouverts d’un

passe-fils pour protéger les fils.

REMARQUE: Le cordon d’alimentation doté d’une fiche

doit passer par un autre trou dans l’armoire.

Branchement électrique du lave-vaisselle

Le branchement électrique s’effectue du côté avant droit du

lave-vaisselle.

• Dans le cas d’un branchement permanent, le câble doit

être acheminé de la façon indiquée à la Figure E. Le câble

doit avoir une longueur minimale de 61 cm (24 po) à partir

du mur arrière.

• Dans le cas d’un branchement avec un cordon

d’alimentation, installez une prise de courant mise à la

terre à trois broches sur la paroi de l’armoire adjacente,

entre 15 cm (6 po) et 46 cm (18 po) de l’ouverture, et

entre 15 cm (6 po) et 46 cm (18 po) du plancher.

• Utilisez uniquement WX09X70910 ou WX09X70911

Trousse de cordon d’alimentation pour lave-vaisselle.

PRÉPARATION DU CÂBLAGE

ÉLECTRIQUE

La page charge ...

GE Profile 988423 Guide d'installation

Marque: GE Profile

Modèle: 988423

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE Profile 988423 Installation guide

Autres documents

GE 31-31524-1 09-12 GE Manuel utilisateur