175D1807P525 49-90257 11-05 JR
350A4502P325 Rev. 1 134287400
ge.com
Dryers
Safety Instructions . . . . . . . . . . . . 2–5
Operating Instructions
Care and Cleaning . . . . . . . . . . . . . . . . . . . .8
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Loading and Using the Dryer . . . . . . . . . .8
Installation Instructions . . . . . 9–20
Electrical Installation for
Electric Dryer . . . . . . . . . . . . . . . . . . . 16, 17
Electrical Requirements . . . . . . . . . . . . . .11
Exhausting the Dryer . . . . . . . . . . . . .12, 13
Gas Connection for Gas Dryer . . . . . . . .18
Gas Supply Requirements . . . . . . . . . . . .13
Location of Your Dryer . . . . . . . . . . . . . . .14
Mobile Home Installation . . . . . . . . . . . . .15
Preparing to Install Your Dryer . . . . .9, 10
Reversing the Door Swing . . . . . . . . . . . .20
Stacking Instructions . . . . . . . . . . . . .19, 20
Troubleshooting Tips . . . . . . . .21, 22
Consumer Support
Consumer Support . . . . . . . . . . . . . . . . . . 26
Warranty for Canadian Customers . . . .25
Warranty for U.S. Customers . . . . . . . . 24
Spacemaker
U.S. Models:
DSXH43
DPXH46
DH43
Canada Models:
DCXH46
PSXH43
Owner’s Manual &
Installation Instructions
®
2
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the state to cause cancer,
birth defects or other reproductive harm and requires businesses to warn customers of potential exposure
to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,
formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be
minimized further by properly venting the dryer to the outdoors.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or death.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light a match, or cigarette, or
turn on any gas or electrical appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Clear the room, building or area of all
occupants.
Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions carefully.
If you cannot reach your gas supplier, call
the fire department.
5
4
3
2
1
■ Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
■ Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
■ Properly ground dryer to conform with all
governing codes and ordinances. Follow
details in Installation Instructions.
■ Install or store where it will not be exposed to
temperatures below freezing or exposed to the
weather.
■ Connect to a properly rated, protected and
sized power supply circuit to avoid electrical
overload.
■ Remove all sharp packing items and dispose of
all shipping materials properly.
Exhaust/Ducting:
This dryer MUST be exhausted to the outside.
Use only rigid metal 4″ diameter ductwork
inside the dryer cabinet. Use only rigid metal
or flexible metal 4″ diameter ductwork for
exhausting to the outside. USE OF PLASTIC OR
OTHER COMBUSTIBLE DUCTWORK CAN CAUSE
A FIRE. PUNCTURED DUCTWORK CAN CAUSE A
FIRE IF IT COLLAPSES OR BECOMES
OTHERWISE RESTRICTED IN USE OR DURING
INSTALLATION.
For complete details, follow the Installation
Instructions.
2
1
PROPER INSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions
before it is used.
3
Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
4
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
YOUR LAUNDRY AREA
■ Keep the area underneath and around your
appliances free of combustible materials, such
as lint, paper, rags and chemicals.
■ Keep the floor around your appliances clean and
dry to reduce the possibility of slipping.
■ Keep area around the exhaust opening and
surrounding areas free from the accumulation
of lint, dust and dirt.
■ Do not obstruct the flow of ventilating air. Do not
stack or place laundry or throw rugs against the
front or back of the dryer.
■ Close supervision is necessary if this appliance is
used by or near children. Do not allow children
to play on, with or inside this or any other
appliance.
■ Keep all laundry aids (such as detergents,
bleaches, etc.) out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid injury.
■ Never climb on or stand on the dryer top.
WHEN USING YOUR DRYER
■ Never reach into the dryer while the drum is
moving. Before loading, unloading or adding
clothes, wait until the drum has completely
stopped.
■ Clean the lint filter before each load to prevent lint
accumulation inside the dryer or in the room.
DO NOT OPERATE THE DRYER WITHOUT THE LINT
FILTER IN PLACE, UNLESS THE DRYING RACK IS IN
USE. Always replace the lint screen when finished
using the drying rack.
■ Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.). These substances give
off vapors that may ignite or explode. Do not add
these substances to the wash water. Do not use or
place these substances around your washer or
dryer during operation.
■ Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beauty salons, restaurants or barber shops, etc.)
must not be placed in or near the dryer until
solvents or flammable materials have been
removed. There are many highly flammable
items used in homes such as acetone, denatured
alcohol, gasoline, kerosene, some household
cleaners, some spot removers, turpentines,
waxes, wax removers and products containing
petroleum distillates.
■ The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
care instructions.
■ Do not dry articles containing rubber, plastic
or similar materials such as padded bras, tennis
shoes, galoshes, bath mats, rugs, bibs, baby pants,
plastic bags and pillows that may melt or burn.
Some rubber materials, when heated, can under
certain circumstances produce fire by
spontaneous combustion.
■ Do not store plastic, paper or clothing that may
burn or melt on top of the dryer during
operation.
■ Garments labeled Dry Away from Heat or Do
Not Tumble Dry (such as life jackets containing
kapok) must not be put in your dryer.
■ Do not dry fiberglass articles in your dryer.
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent dryer uses.
■ To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the dryer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning
(except the removal and cleaning of the lint
filter). NOTE: Turning the Cycle Selector knob
to an OFF position does NOT disconnect the
appliance from the power supply.
■ Do not spray any type of aerosol into, on or near
dryer at any time.
■ Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a clothes load to catch fire.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
WHEN NOT USING YOUR DRYER
■ Grasp the plug firmly when disconnecting this
appliance to avoid damage to the cord while
pulling. Place the cord away from traffic areas so
it will not be stepped on, tripped over or
subjected to damage.
■ Do not attempt to repair or replace any part of
this appliance or attempt any servicing unless
specifically recommended in this Owner’s Manual
or in published user-repair instructions that you
understand and have the skills to carry out.
■ Before discarding a dryer, or removing it from
service, remove the dryer door to prevent
children from hiding inside.
■ Do not tamper with controls.
■ Never attempt to operate this appliance if
it is damaged, malfunctioning, partially
disassembled or has missing or broken parts,
including a damaged cord or plug.
■ The interior of the machine and the exhaust
duct connection inside the dryer should be
cleaned at least once a year by a qualified
technician. See the Loading and Using the Dryer
section. Do not use any type of spray cleaner
when cleaning dryer interior. Hazardous fumes
or electrical shock could occur.
■ If yours is a gas dryer, it is equipped with an
automatic electric ignition and does not have a
pilot light. DO NOT ATTEMPT TO LIGHT WITH A
MATCH. Burns may result from having your hand
in the vicinity of the burner when the automatic
ignition turns on.
■ You may wish to soften your laundered fabrics
or reduce the static electricity in them by using
a dryer-applied fabric softener or an antistatic
conditioner. We recommend you use either a
fabric softener in the wash cycle, according to the
manufacturer’s instructions for those products,
or try a dryer-added product for which the
manufacturer gives written assurance on the
package that their product can be safely used in
your dryer. Service or performance problems
caused by use of these products are the
responsibility of the manufacturers of those
products and are not covered under the warranty
to this appliance.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
5
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation Instructions
WARNING!
6
About the dryer control panel.
Control Settings
Fabric Care
COTTONS For regular to heavy cottons.
REG. HEAT
PERM. PRESS For synthetics, blends and items labeled permanent press or tumble dry medium heat.
MED HEAT
KNITS/ For knits, delicates, synthetics and items labeled tumble dry low heat.
DELICATES
LOW HEAT
AIR FLUFF For fluffing items without heat. Use the TIMED DRY cycle.
NO HEAT
Drying Cycles
The COTTONS, EASY CARE and DELICATES cycles automatically sense fabric dryness. Select MORE DRY
for heavier fabrics, LESS DRY for lighter fabrics. The TIMED DRY cycle will run for a selected time.
COTTONS For cottons and most linens. For most loads, select the Optimum Dry setting (on some models).
EASY CARE For wrinkle free, permanent press and delicate items, and knits. For most loads, select the
PERM PRESS Optimum Dry setting (on some models).
DELICATES For delicates and special care fabrics. For most loads, select the Optimum Dry
setting (on some models).
TIMED DRY Set the Cycle Selector at the desired drying time.
Start
Close the dryer door. Select START. Opening the door during operation will stop the dryer. To restart
the dryer, close the door and select START to complete the cycle.
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Features and appearance may vary.
Models DPXH46 and DCXH46
Models DSXH43, DH43 and PSXH43
About your dryer features.
Cycle Signal Option (on some models)
When the signal is on it will sound just
before the end of the cycle to remind
you to remove the clothes. The signal
can be set at OFF (no sound), LOUD or
anywhere in between.
If the dried load cannot be removed
promptly during the EASY CARE cycle,
the Cycle Selector will advance to the
EXTENDED COOL DOWN setting. Unheated
tumbling continues during EXTENDED
COOL DOWN and WRINKLE CARE (on
some models) for 40 minutes to help
reduce wrinkling. When the CYCLE
SIGNAL is on, it will sound briefly every
five minutes as a reminder to remove
the load.
NOTE:
■ If items are removed before the end of
the cycle, turn the CYCLE SELECTOR knob
to OFF.
■ Remove garments promptly at the sound
of the signal. Place clothes on hangers
so wrinkles won’t set in.
■ Use the Cycle Signal especially when
drying fabrics like polyester knits and
permanent press. These fabrics should
be removed so wrinkles won’t set in.
CYCLE SIGNAL
OFF LOUD
Replacing the Dryer Light Bulb (on some models)
WARNING: To reduce the
risk of electric shock, disconnect this
appliance from the power supply
before attempting any user
maintenance. Turning the controls
to the OFF position does not
disconnect this appliance from the
power supply.
The dryer light is located above the dryer
door opening.
Before replacing the light bulb, be sure to
unplug the dryer power cord or disconnect
the dryer at the household distribution
panel by removing the fuse or switching
off the circuit breaker.
To replace the dryer light:
Using a small flat blade screwdriver,
pry the bottom of the light cover out
and off the light housing.
Unscrew the bulb when cool and
replace it with an appliance bulb of
the same or lower wattage.
Snap the light cover back on the light
housing.
3
2
1
Drying Rack (on some models)
A handy drying rack may be used for drying
articles such as stuffed toys, pillows or
washable sweaters.
Remove the lint screen.
Place the front bar under the lip of the
lint screen opening.
When items are dry, remove the rack
and replace the lint screen. DO NOT
OPERATE THE DRYER WITHOUT THE LINT
SCREEN IN PLACE UNLESS THE DRYING
RACK IS IN PLACE.
NOTE:
■ The drying rack must be used with the
TIMED DRY cycle.
■ Do not use this drying rack when there
are other clothes in the dryer.
3
2
1
Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Pry with
flat blade
screwdriver
Light
housing
Light
cover
Wrinkle Care Option (on some models)
Use this option to minimize the wrinkles
in clothes. It provides approximately 15
minutes of no-heat tumbling after the
clothes are dry.
This option can only be used with the EASY
CARE and DELICATES cycles.
WRINKLE CARE
EXTENDED COOL AIR TUMBLE
ON OFF
7
As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains.
Bounce
®
Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance
with the manufacturer’s instructions.
Do not overload. This wastes energy and causes wrinkling.
Do not dry the following items: fiberglass items, woolens, rubber-coated items, plastics, items with plastic trim and
foam-filled items.
8
Loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering.
Sorting and Loading Hints
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control panel
and finishes may be damaged by some laundry
pretreatment soil and stain remover products.
Apply these products away from the dryer. The
fabric may then be washed and dried normally.
Damage to your dryer caused by these products is
not covered by your warranty.
The Lint Screen: Clean the lint screen before each
use. Lint buildup in the screen restricts air flow,
which causes longer drying times. The screen is
located at the bottom of the door opening. Remove
by pulling straight up. Remove the lint and replace
the screen.
A waxy buildup may form on the lint screen from
using dryer-added fabric softener sheets. To remove
this buildup, wash the lint screen in warm, soapy
water. Dry thoroughly and replace. Do not operate
the dryer without the lint screen in place.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging. A
partially clogged exhaust can lengthen the drying
time.
Follow these steps:
Turn off electrical supply by disconnecting the
plug from the wall socket.
Disconnect the duct from the dryer.
Vacuum the duct with the hose attachment and
reconnect the duct.
The Exhaust Hood: Check from the outside that the
flaps of the hood move freely when operating. Make
sure that there is no wildlife (birds, insects, etc.)
nesting inside the duct or hood.
3
2
1
Care and Cleaning of the Dryer
Consumer Support
Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Installation
Spacemaker Dryer
Instructions
Models DCXH46
DSXH43
DPXH46
DH43
PSXH43
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these
instructions for local inspector’s use.
•
IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time – 1–3 hours
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
WARNING
• This dryer must be exhausted to the outdoors. Use
only rigid metal or flexible metal 4" diameter ductwork
for exhausting to the outside. Use only rigid metal 4"
diameter ductwork inside the dryer cabinet.
• Never use plastic or other combustible ductwork. See
Exhausting section.
• This appliance must be properly grounded and
installed as described in these Installation Instructions.
• Do not install or store appliance in an area where it will
be exposed to water/weather. See Location of Your Dryer
section.
• The National Fuel Gas code restricts installations of
gas appliances in garages. They must be 18″ (45.7 cm)
off the ground and protected from vehicles by a
barrier. See Location of Your Dryer section.
• The electrical service to the dryer must conform with
local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70 or in Canada,
CSA C22.1 Canadian Electrical Code Part 1.
• The gas service to the dryer must conform with local
codes and ordinances or the latest edition of the
National Fuel Gas Code ANSI Z223.1 or in Canada,
CAN/CGA B149.12. The gas dryer is designed under
ANSI Z 21.5.1 or ANSI/UL2158–CAN/CSA C22.2
(latest editions) for home use only. This dryer is not
recommended for commercial applications such as
restaurants or beauty salons.
FOR YOUR SAFETY:
9
If you have any questions, in the U.S., call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com
In Canada, call 1.800.361.3400
or visit our Website at: geappliances.ca
IN THE COMMONWEALTH OF
MASSACHUSETTS
• This product must be installed by a licensed
plumber or gas fitter.
• When using ball-type gas shut-off valves, they
shall be the T-handle type.
• A flexible gas connector, when used, must not
exceed 3 feet.
1. Prepare the area and exhaust for installation
of the new dryer.
2. Check to be sure that the existing external
exhaust is clean and that it meets attached
installation specifications.
3. Place the four corner posts from the shipping
carton on the floor, parallel to each other, 2–3″
apart. Carefully lay the dryer on its left side on
top of the corner posts. Remove the foam
shipping pad.
CAUTION: To prevent damage, do
not use the control panel as a means to pick up
or move the dryer.
4. Return the dryer to an upright position.
5. Move the dryer to the desired location.
6. Connect the external exhaust.
7. Adjust the leveling legs to match the washer
height. The dryer must be level and rest firmly
on all four leveling legs.
8. Connect the power supply.
9. Check the operation of the power supply and
venting.
10. Place the Owner’s Manual and the Installation
Instructions in a location where they will be
noticed by the owner.
Installation Instructions
TOOLS AND MATERIALS
YOU WILL NEED
Phillips head screwdriver
Adjustable pliers (adjust leveling legs)
Carpenter’s level
Flat or straight blade screwdriver (may be needed
for cord strain relief)
Duct tape
Rigid or UL-listed flexible metal 4″ (10.2 cm) duct
Vent hood
1/4″ nut driver (remove terminal block access
cover and install cord) (ELECTRIC DRYER)
Pipe thread sealer (GAS DRYER)
UL-listed strain relief (may be supplied
with cord)
UL-listed 30A, 240V, 3-wire, #10 AWG minimum
conductor power cord (U.S. existing structure)
UL-listed 30A, 240V, 4-wire, #10 AWG
minimum conductor power cord is required
(U.S. new construction)
Flexible stainless steel or plastic-coated brass
connnecting tube (if allowed by building code)
(GAS DRYER)
Open-end wrenches for flexible tube and
connector (GAS DRYER)
PREPARING THE INSTALLATION SITE
AND UNPACKING YOUR DRYER
Foam shipping pad
Back of
Dryer
10
Packing
ELECTRICAL CONNECTION
INFORMATION FOR
ELECTRIC DRYERS
Installation Instructions
WARNING –
To reduce the risk of
fire, electric shock or personal injury:
• DO NOT USE AN EXTENSION CORD WITH
THIS APPLIANCE.
• THIS APPLIANCE MUST BE PROPERLY
GROUNDED.
This dryer must be electrically grounded in accordance
with local codes and ordinances, or in the absence of local
codes, in accordance with the NATIONAL ELECTRICAL
CODE, ANSI/NFPA NO. 70 or in Canada CSA C22.1
Canadian Electrical Code Part 1.
Electrical Requirements
• This dryer must be connected to a 208V or 240V
individual branch circuit, protected by 30-amp circuit
breakers or time-delay fuses.
• Power supply: 3-wire 240-volt, single-phase, 60-Hz,
Alternating Current. (Canada–240 volt, single-phase,
60-Hz Alternating Current.)
• Use copper conductors only.
• If the electric supply does not meet the above
specifications, call a licensed electrician.
NOTE: A wiring diagram is located under the top panel.
ELECTRICAL CONNECTION
INFORMATION FOR GAS DRYERS
WARNING –
To reduce the risk of
fire, electric shock or personal injury:
• DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG WITH THIS APPLIANCE.
•
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD GROUNDING PRONG FROM
THE POWER CORD.
This dryer
must be electrically grounded in accordance
with local codes and ordinances, or in the absence of local
codes, in accordance with the NATIONAL ELECTRICAL
CODE, ANSI/NFPA NO. 70 or in Canada, CSA C22.1
Canadian Electrical Code Part 1.
Electrical Requirements
• This dryer must be supplied with 120V, 60-Hz,
and connected to a properly grounded branch
circuit, protected by a 15- or 20-amp circuit breaker
or time-delay fuse.
• If the electric supply provided does not meet the
above specifications, it is recommended that a licensed
electrician install an approved outlet.
External Ground (if required)
An external ground wire (not provided), which meets local
codes, may be added by attaching it to the green ground
screw on the rear of the dryer in the upper left corner
above the cord, and to grounded metal cold water pipe or
other established ground.
NOTE: A wiring diagram is located under the top panel.
Attach ground wire
(obtain locally)
Ensure proper ground
exists before use
11
Read these instructions completely and carefully.
EXHAUST SYSTEM
REQUIREMENTS
Installation Instructions
Use only 4″ (10.2 cm) diameter (minimum) rigid metal
duct for best performance, or flexible metal duct, and
approved vent hood which has swing-out dampers that
open when the dryer is in operation. When the dryer
stops, the dampers automatically close to prevent drafts
and the entrance of insects and rodents. To avoid
restricting the outlet, maintain a minimum of 12″
(30.5 cm) clearance between the vent hood and the
ground or any other obstruction.
If all rigid metal duct cannot be used, then flexible
all-metal venting can be used, but it will reduce the
maximum recommended duct length. See Additional
Installation Instructions following.
WARNING – The following are specific
requirements for proper and safe operation
of your dryer. Failure to follow these instructions can
create excessive drying times and fire hazards.
DO NOT use plastic flexible duct to exhaust the dryer.
Excessive lint can build up inside exhaust system and create
a fire hazard and restrict air flow. Restricted air flow will
increase drying times. If your present system is made up of
plastic duct or metal foil duct, replace it with rigid or
flexible metal duct. Ensure the present duct is free of any
lint prior to installing dryer duct.
If the dryer is not exhausted outdoors, some fine lint will
be expelled into the laundry area. An accumulation of lint
in any area of the home can create a health and fire hazard.
This dryer exhaust system MUST BE EXHAUSTED TO
THE OUTSIDE of the dwelling.
DO NOT allow combustible materials (for example:
clothing, draperies/curtains, paper) to come in contact with
exhaust system.
12
Correct
Incorrect
Do
Don’t
Don’t
Don’t
WARNING
The dryer MUST NOT be exhausted into a chimney,
a wall, a ceiling, a common duct with a kitchen exhaust or
any concealed space of a building which can accumulate
lint, resulting in a fire hazard.
DO NOT exceed the length of duct pipe or number of
elbows allowed in the Maximum Length charts. Lint can
accumulate in the exhaust system, plugging the system and
creating a fire hazard, as well as increasing drying times.
DO NOT screen the exhaust ends of the vent system, or
use any screws or rivets to assemble the exhaust system.
Lint can become caught in the screen, on the screws or
rivets, clogging the duct work and creating a fire hazard
as well as increasing drying times. Use an approved vent
hood to terminate the duct outdoors, and seal all joints
with duct tape. All male duct pipe fittings MUST be
installed downstream with the flow of air.
EXPLOSION HAZARD. Do not install the dryer where
gasoline or other flammables are kept or stored. If the
dryer is installed in a garage, it must be a minimum of 18″
(45.7 cm) above the floor. Failure to do so can result in
death, explosion, fire or burns.
ADDITIONAL INSTALLATION
INSTRUCTIONS
If all rigid metal duct cannot be used, then flexible
all-metal venting can be used, but it will reduce the
maximum recommended duct length. In special
installations when it is impossible to make a connection
with the above recommendations, then UL-listed clothes
dryer transition duct may be used as transition venting
between the dryer and wall connection only. The use of
this ducting will affect drying time.
If flexible transition duct is necessary, only UL-listed duct
identified for use with clothes dryers is approved.
The following directions must be followed.
• Use the shortest length possible.
• Stretch the duct to its maximum length.
• Do not crush or collapse.
• Never use transition duct inside the wall or inside
the dryer.
• Avoid resting the duct on sharp objects.
• Venting must conform to local building codes.
Installation Instructions
EXHAUST DUCTING LENGTH
The exhaust system should be inspected and cleaned a
minimum of every year with normal usage. The more the
dryer is used, the more often you should check the exhaust
system and vent hood for proper operation.
• DO NOT assemble the duct work with fasteners that
extend into the duct. They will serve as collection points
for lint.
• Insulation – Ductwork which runs through an unheated
area or is near an air conditioning duct should be
insulated to reduce condensation and lint buildup.
MAXIMUM LENGTH
of 4“ (10.2 cm) Dia. FLEXIBLE METAL TUBING
PREFERRED VENT HOOD TYPE
0 30’ (9.14 m) 18’ (5.49 m)
1 22’ (6.71 m) 14’ (4.27 m)
2 14’ (4.27 m) 10’ (3.05 m)
4” (10.2 cm) Louvered
4”
(10.2 cm)
Number
of 90°
turns
2.5”
(6.35
cm)
MAXIMUM LENGTH
of 4“ (10.2 cm) Dia. RIGID METAL DUCT
PREFERRED VENT HOOD TYPE
0 60’ (18.28 m) 48’ (14.63 m)
1 52’ (15.84 m) 40’ (12.19 m)
2 44’ (13.41 m) 32’ (9.75 m)
3 32’ (9.75 m) 24’ (7.31 m)
4 28’ (8.53 m) 16’ (4.87 m)
4” (10.2 cm) Louvered
4”
(10.2 cm)
Number
of 90°
turns
2.5”
(6.35
cm)
CORRECT
INCORRECT
INSTALL MALE FITTINGS IN
CORRECT DIRECTION
EXHAUST DIRECTION
All dryers are shipped set up for rear exhausting.
On electric dryers, exhausting can be on the cabinet right
or left side, or through the dryer bottom. Gas dryers can
exhaust on the cabinet right side or the dryer bottom. To
change exhaust direction you will need Exhaust Kit Pub.
No. 14-A018 and a rigid metal 4″ 90-degree elbow. The kit
is available through your GE retailer. Follow the
instructions supplied with the kit.
Same as
other side
EXHAUST DUCT LOCATING
DIMENSIONS
3 3/4″ (9.5 cm)
3 3/4″ (9.5 cm)
13 5/16″
(34 cm)
4 3/8″
(11 cm)
5 7/8″
(15 cm)
GAS SUPPLY REQUIREMENTS
Replace brass connecting pipe that is not plastic-coated.
Stainless steel or plastic-coated brass MUST be used.
WARNING: Never reuse old flexible
connectors. The use of old flexible connectors can cause
gas leaks and personal injury. Always use NEW flexible
connectors when installing a gas appliance.
1. Installation MUST conform with local codes, or in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 (latest edition) or in Canada, the
current CAN/CGA B149.
2. The gas supply line should be of 1/2″ (1.27 cm) rigid
pipe.
3. If codes allow, flexible metal tubing may be used
to connect your dryer to the gas supply line. The
tubing MUST be constructed of stainless steel or
plastic-coated brass.
4. The gas supply line MUST have an individual shutoff
valve.
5. A 1/8″ (0.32 cm) NPT plugged tapping, accessible for
test gauge connection, MUST be installed immediately
upstream of the gas supply connection to the dryer.
6. The dryer MUST be disconnected from the gas supply
piping system during any pressure testing of the gas
supply piping system at test pressures in excess of 1/2
psig (3.45 kPa).
7. The dryer MUST be isolated from the gas supply piping
system during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2 psig (3.45 kPa).
13
Installation Instructions
14
LOCATION OF YOUR DRYER
Do Not Install the Dryer:
1. Do not install the dryer in an area exposed to dripping
water or outside weather conditions.
2. Do not install the dryer in an area where it will come
in contact with curtains, drapes or anything that will
obstruct the flow of combustion and ventilation air.
3. Do not install the dryer on carpet.
Floor MUST be solid with a maximum slope
of 1″ (2.54 cm).
Undercounter Installation:
If an undercounter* installation is desired, the dryer
MUST have a top sheet kit installed, Pub. No. 14–A008.
Kit is available through your GE retailer.
*Custom-sized countertop is required.
Installation in Recess or Closet:
1. This dryer MUST be exhausted outdoors.
2. No other fuel burning appliance shall be installed in the
same closet as the GAS DRYER.
3. Your dryer needs the space around it for proper
ventilation. DO NOT INSTALL YOUR DRYER IN A
CLOSET WITH A SOLID DOOR.
4. Closet doors must be louvered or otherwise ventilated
and must contain a minimum of 60 sq. in. of open area
equally distributed. If the closet contains both a washer
and a dryer, doors must contain a minimum of 120 sq.
in. of open area equally distributed. Air openings are
required to be unobstructed when a door is installed.
A louvered door with equivalent air openings for the full
length of the door is acceptable.
60 sq. in.
(387.1 sq. cm)
60 sq. in.
(387.1 sq. cm)
Closet door
3 in.
(7.6 cm)
3 in.
(7.6 cm)
0″
(0 cm)
0″
(0 cm)
3″
(7.6 cm)
Allow the following clearances for ease of installation:
FRONT SIDES REAR TOP
Alcove, stack, 3” (7.6 cm) 0 (0 cm) 3” (7.6 cm) 0 (0 cm)
undercounter
or closet
THIS DRYER MUST BE EXHAUSTED OUTDOORS.
5. The following illustrations show minimum clearance
dimensions for proper operation in a recess or closet
installation.
3″
(7.6 cm)
Installation Instructions
15
MOBILE HOME INSTALLATION
1. Dryer MUST be exhausted outside (outdoors, not
beneath the mobile home) using metal ducting that will
not support combustion. Metal ducting must be 4″
(10.16 cm) in diameter with no obstructions. Rigid metal
duct is preferred.
2. If the dryer is exhausted through the floor, the exhaust
system MUST NOT terminate beneath the mobile
home. Termination MUST be securely fastened to the
mobile home structure.
3. When installing a gas dryer into a mobile home, a
provision must be made for outside make-up air. This
provision is to be not less than twice the area of the dryer
exhaust outlet.
4. Gas dryers MUST be fastened to the floor using Mobile
Home Installation Kit Pub. No. 14–D346–33.
5. See the Exhaust System Requirements section for other
important venting information.
6. Installation MUST conform to current Manufactured
Home Construction & Safety Standard (which is a
Federal Regulation Title 24 CFR—Part 32–80) or,
when such standard is not applicable, with American
National Standard for Mobile Homes, ANSI/NFPA No.
501B. In Canada, the CSA Z240 is applicable.
The dryer is designed under ANSI Z 21.5.1.
Correct
Incorrect
Do
Don’t
Don’t
Don’t
ROUGH-IN DIMENSIONS
47 1/2″
(120.7 cm)
3/4″
(1.9 cm)
Door open
90˚
4 3/8″
(11.1 cm)
Optional
vent knockout
25 3/4″
(65.4 cm)
3 3/4″
(9.5 cm)
SIDE VIEW
Under
counter
34 5/8″
(87.9 cm)
2 9/16″
(6.5 cm)
13 9/16″
(34.5 cm)
36″
(91.5 cm)
Electrical connection
3/16″ (0.48 cm) Dia.
gas pipe
1″ (2.54 cm)
3 3/4″
(9.5 cm)
REAR VIEW
26 7/8″
(68.3 cm)
SERVICING – Consideration must be given to provide
adequate clearances for installation and servicing.
Installation Instructions
16
GROUNDING REQUIREMENTS
WARNING: The following are specific
requirements for proper and safe electrical installation of
your dryer. Failure to follow these instructions can create
electrical shock and/or a fire hazard.
This appliance MUST be properly grounded.
Electrical shock can result if the dryer is not properly
grounded. Follow the instructions in this manual for proper
grounding.
DO NOT use an extension cord with this dryer. Some
extension cords are not designed to withstand the amounts
of electrical current this dryer utilizes and can melt,
creating electrical shock and/or fire hazard. Locate the
dryer within reach of the wall outlet, taking into account
the length of power cord to be purchased and allowing
some slack in the cord. Refer to Electrical Requirements in
this manual for the proper power cord to be purchased.
A UL-listed strain relief must be installed onto power cord.
If the strain relief is not attached, the cord can be pulled
out of the dryer and can be cut by any movement of the
cord, resulting in electrical shock.
NOTE: Dryers operating on 208-volt power supply will
have longer drying times than those operating
on 240-volt power supply.
A wiring diagram is located under the top panel.
ELECTRICAL INSTALLATION FOR
ELECTRIC DRYERS
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a licensed electrician if you are in
doubt as to whether the appliance is properly grounded.
The dryer MUST be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electrical shock by creating a path of least resistance for
electrical current.
Grounding must be in accordance with local codes and
ordinances, or in the absence of local codes, in accordance
with the National Electrical Code ANSI/NFPA No. 70.
For a grounded, cord-connected electric dryer:
If your dryer is equipped with a power supply cord having
an equipment-grounding conductor and a grounding
plug, the plug MUST be plugged into an appropriate,
copper-wired receptacle (in the U.S.), or in Canada, an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances. If in
doubt, call a licensed electrician.
For a permanently connected electric dryer:
• The dryer MUST be connected to a grounded metal,
permanent wiring system; or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead
on the appliance.
For a grounded, cord-connected gas dryer:
• This dryer is equipped with a three-prong (grounding)
plug for your protection against shock hazard and should
be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong
from this plug. Do not modify the plug on this appliance.
If it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
NOT for use in Canada.
DO NOT use for Mobile Home Installations.
NOT for use on new construction.
1. Remove the screws securing the terminal block access
cover and the strain relief mounting bracket located on
the back of the dryer upper corner.
2. Install a UL-listed strain relief into the power cord entry
hole of the mounting bracket. Finger-tighten the nut
only at this time.
3. Thread a UL-listed 30A, 240V, 3 #10 AWG minimum
copper conductor power cord through the strain relief.
4. Attach the power cord neutral (center wire) conductor
to the silver-colored center terminal on the terminal
block. Tighten the screw securely.
5. Attach the remaining two power cord outer conductors
to the outer brass-colored terminals on the terminal
block. Tighten both screws securely.
WARNING: Do not make a sharp bend or
crimp wiring/conductor at connections.
6. Reattach the strain relief mounting bracket to the
back of the dryer with screws provided. Tighten screws
securely.
7. Tighten the screws securing the cord restraint firmly
against the power cord.
8. Tighten the strain relief nut securely so that the strain
relief does not turn.
9. Reinstall the terminal block access cover.
3-WIRE SYSTEM FOR
ELECTRIC DRYERS
Installation Instructions
17
Green ground screw
Silver terminal
Nut
Tighten nut to
these threads
Power cord
Strain relief
mounting bracket
Green neutral
ground wire
Use copper
conductors only.
Effective January 1, 1996: The National Electrical Code
requires that new construction (non existing) utilize a
4-wire connection to an electric dryer.
In Canada a 4-wire power supply cord is installed on
the dryer.
1. Remove the screws securing the terminal block access
cover and the strain relief mounting bracket located on
the back of the dryer upper corner.
2. Install a UL-listed strain relief in the entry hole of
the mounting bracket. Finger-tighten the nut only
at this time.
3. Remove the green neutral ground wire from the green
ground screw located above the terminal block.
4. Thread a UL-listed 30A, 240V, 4 #10 AWG minimum
copper conductor power cord through the strain relief.
5. Attach the green power cord ground wire to the
cabinet with the green ground screw.
6. Attach the white (neutral) power cord conductor from
the power cord and the green ground wire from the
dryer harness to the silver-colored center terminal on
the terminal block. Tighten the screw securely.
7. Attach the red and black power cord conductors to the
outer brass-colored terminals on the terminal block.
WARNING: Do not make a sharp bend
or crimp wiring/conductor at the connections.
8. Tighten the screws securing the cord restraint firmly
against the power cord.
9. Tighten the strain relief nut securely so the strain relief
does not turn.
10. Reinstall the terminal block access cover.
4-WIRE SYSTEM FOR
ELECTRIC DRYERS
Typical 4
conductor
receptacle
Black 240V
White neutral
Red 240V
Green ground
Typical
4 conductor cord
Green ground
screw
Green neutral
ground wire
Red
White
Black
Terminal block
Silver terminal
Green power cord ground wire
Nut
Tighten nut to
these threads
Power cord
Strain
relief
mounting
bracket
1. Remove the shipping cap from gas pipe at the rear of
the dryer.
Conversion to LP Gas: DO NOT connect the dryer to
LP gas service without converting the gas valve. An LP
conversion kit (Pub. No. 14–A038) MUST be installed
by a qualified gas technician.
a. Connect a 1/2″ (1.27 cm) I.D. semi-rigid
or approved pipe from gas supply line to
the 3/8″ (0.96 cm) pipe located on the back of the
dryer. Use a 1/2″ to 3/8″ (1.27 cm to 0.96 cm)
reducer for a connection. Apply an approved thread
sealer that is resistant to the corrosive action of
liquefied gases on all pipe connections.
b. Open the shutoff valve in the gas supply line.
c. Test all connections by brushing on a soapy water
solution.
WARNING: NEVER TEST
FOR GAS LEAKS WITH AN
OPEN FLAME.
2. Connect the exhaust duct to outside exhaust system.
Use duct tape to seal all joints.
3. With the dryer in its final position, adjust one or more
of the legs until the dryer is resting solidly on all four
legs. Place a level on top of the dryer. THE DRYER
MUST BE LEVEL AND RESTING SOLIDLY ON
ALL FOUR LEGS.
4. Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at circuit
breaker/fuse box before plugging the power cord
into the outlet.
5. Turn on the power at the circuit breaker/fuse box.
GAS CONNECTION FOR
GAS DRYERS
Installation Instructions
18
CAUTION: Before operating the dryer,
make sure the dryer area is clear and free from
combustible materials, gasoline, and other flammable
vapors. Also see that nothing (such as boxes,
clothing, etc.) obstructs the flow of combustion and
ventilation air.
6. Run the dryer through a cycle check for proper
operation.
NOTE: On gas dryers, before the burner will light, it is
necessary for the gas line to be bled of air. If the burner
does not light within 45 seconds the first time the dryer is
turned on, the safety switch will shut the burner off. If this
happens, turn the timer to OFF and wait 5 minutes before
making another attempt to light.
7. If your dryer does not operate, please review the
Troubleshooting Tips section in this manual before
calling for service.
8. Place these instructions in a location near the dryer for
future reference.
WARNING:
• To reduce the risk of electric shock, disconnect this
appliance from the power supply before attempting
any user maintenance. Turning the controls to the
OFF position does not disconnect this appliance
from the power supply.
• Refer to the washer and dryer installation instructions
prior to stacking appliances. Reading all of the
information contained in these instructions will simplify
the installation and ensure a correct and safe operation.
A fire hazard and/or personal injury could result from
improper installation.
Stacking Instructions
19
TOOLS REQUIRED FOR STACKING
THE DRYER
• Phillips head screwdriver
• Channel-lock adjustable pliers
MOUNTING THE DRYER TO
THE WASHER
The numbers in the illustration correspond to steps.
1. Remove the washer top panel by first removing the 4
screws in the 2 brackets located on the top rear of the
washer.
Slide the top forward, lift the front of the top up and
remove the top panel.
Remove the 2 brackets from the rear of the top panel.
2. Using the 4 screws that were removed in step 1, install
the brackets in the rear support as shown.
3. Remove the 4 screws and the 2 long front brackets
located on the top front of the washer.
4. Install the 2 new front mounting brackets provided and
the 4 screws that were removed in step 3. Note that the
tab of the front mounting bracket is facing forward as
shown in the illustration.
The numbers in the illustration correspond to steps.
5. Using the blade end of a putty knife covered with
masking tape, carefully remove the hole plugs located
in the bottom of the dryer front panel.
6. Remove the 4 legs from the dryer base.
7. Place the dryer on top of the washer. Slide the dryer
back into the rear brackets (7A) then drop the front
down over the front brackets (7B).
Stacking Instructions–Reversing Door Swing
20
REVERSING THE DRYER
DOOR SWING
1. Open the dryer door. Remove the 4 hinge hole plugs or
screws from the left side of door opening. Place nearby
for future installation. NOTE: You may need a plastic knife
to help pull out the plugs. Be careful not to scratch the paint.
2. Remove the four screws that secure the door hinges to
the dryer front panel. NOTE: Remove 1 screw from each
of the 2 hinges first. Hold the door firmly before removing the
last 2 screws.
3. Rotate the door 180° and reinstall the door hinges to the
dryer front panel with the 4 screws.
4. Install the 4 hinge hole plugs or screws that were
removed in step 1 into the open screw holes on the right
side of the door opening.
Remove 4 screws—one from each hinge first
8. Insert the 2 long screws provided in the kit through
the holes in the dryer front panel and install into the
front mounting brackets.
9. Install the hole plugs removed in step 5.
10. Refer to the washer and dryer installation instructions
for proper installation and function.
11. Save the top panel and brackets in the case of future
side-by-side use.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
dans d''autres langues
- English: GE DPXH46EFWW Owner's manual
Documents connexes
-
GE DPXH46GFCC Manuel utilisateur
-
GE DPXH46GFCC Manuel utilisateur
-
-
-
GE PFDS450ELWW Manuel utilisateur
-
-
GE PFDN440 Manuel utilisateur
-
-
GE 513 Manuel utilisateur
-