Schumacher SL1327SL1327 Le manuel du propriétaire

Marque: Schumacher

Modèle: SL1327SL1327

Taper: Le manuel du propriétaire

Ce manuel convient également à

0099002114E-00

Jump Starter/

Power Pack

Arrancador /

Pack de energía

Aide de Démarrage /

Bloc d’alimentation

OWNER’S MANUAL / MANUAL DEL USUARIO

MANUEL D’UTILISATION

PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE

EACH USE. This manual will explain how to use the unit safely

and effectively. Please read and follow these instructions and

precautions carefully.

POR FAVOR GUARDE ESTE MANUAL DEL PROPIETARIO Y

LEER ANTES DE CADA USO. En este manual se explica cómo

utilizar la unidad segura y efectiva. Por favor, lea y siga las siguientes

instrucciones y precauciones.

ESSAYER DE GARDER LE MANUEL D’INSTRUCTIONS ET LE

LIRE AVANT CHAQUE UTILISATION. Ce manuel explique comment

utiliser l’unité d’une façon sûre et efcace. S’il vous plaît lisez et suivez

ces instructions et précautions.

BASE MODEL / MODELO BASE / VERSION DE BASE

SL010

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ...................................................... 5

PERSONAL PRECAUTIONS ......................................................................... 6

PREPARING TO USE THE UNIT .................................................................. 7

FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY .............. 7

FEATURES ..................................................................................................... 8

CHARGING THE JUMP STARTER ............................................................... 8

OPERATING INSTRUCTIONS ...................................................................... 9

MAINTENANCE INSTRUCTIONS ................................................................11

STORAGE INSTRUCTIONS .........................................................................11

TROUBLESHOOTING ..................................................................................11

BEFORE RETURNING FOR REPAIRS ....................................................... 13

SPECIFICATIONS ........................................................................................ 13

REPLACEMENT PARTS .............................................................................. 13

LIMITED WARRANTY .................................................................................. 14

WARRANTY CARD ...................................................................................... 15

CONTENIDOS

INSTRUCCIONES IMPORTANTES DE SEGURIDAD ............................... 16

PRECAUCIONES DE SEGURIDAD PERSONAL ....................................... 17

PREPARACIÓN PARA EL USO ................................................................... 18

SIGA ESTOS PASOS CUANDO SE CONECTE A LA BATERÍA ................ 18

CARACTERÍSTICAS .................................................................................... 19

CARGAR EL ARRANCADOR ...................................................................... 20

INSTRUCCIONES DE OPERACIÓN ........................................................... 20

INSTRUCCIONES DE MANTENIMIENTO .................................................. 22

INSTRUCCIONES DE ALMACENAMIENTO .............................................. 22

RESOLUCIÓN DE PROBLEMAS ................................................................ 23

ANTES DE DEVOLVER A REPARACIONES .............................................. 24

ESPECIFICACIONES .................................................................................. 24

REPUESTOS ................................................................................................ 25

GARANTÍA LIMITADA .................................................................................. 25

TARJETA DE GARANTÍA ............................................................................. 26

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ IMPORTANTES ........................................... 27

MESURES DE SÉCURITÉ PERSONNELLE .............................................. 28

PRÉPARATION UTILISER L’APPAREIL ...................................................... 29

SUIVEZ CES ÉTAPES LORSQUE CONNEXION À UNE BATTERIE ........ 29

CARACTÉRISTIQUES ................................................................................. 30

CHARGE LE DÉMARREUR ........................................................................ 31

CONSIGNES D’UTILISATION ..................................................................... 31

CONSIGNES D’ENTRETIEN ....................................................................... 33

INSTRUCTIONS DE STOCKAGE ............................................................... 34

TABLEAU DE DÉPANNAGE ........................................................................ 34

AVANT DE RETOURNER POUR LES RÉPARATIONS .............................. 35

SPÉCIFICATIONS ........................................................................................ 36

PIÈCES DE RECHANGE ............................................................................. 36

GARANTIE LIMITÉE .................................................................................... 36

CARTE DE GARANTIE ................................................................................ 38

• 5 •

1. IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

WARNING – RISK OF EXPLOSIVE GASES.

WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS

DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES

DURING NORMAL OPERATION. IT IS IMPORTANT THAT YOU

FOLLOW THESE INSTRUCTIONS EACH TIME YOU USE THE UNIT.

To reduce the risk of battery explosion, follow these instructions and

those published by the battery manufacturer and the manufacturer

of any equipment you intend to use in the vicinity of a battery.

Review cautionary markings on these products and on the engine.

WARNING! RISK OF ELECTRIC SHOCK OR FIRE.

1.1 Read the entire manual before using this product. Failure to do so

could result in serious injury or death.

1.2 Keep out of reach of children.

1.3 Do not put ngers or hands into any of the unit’s outlets.

1.4 Do not expose the unit to rain or snow.

1.5 Use only recommended attachments (SA883 jump cable). Use of an

attachment not recommended or sold by the jump starter manufacturer

for the unit may result in a risk of re, electric shock or injury to persons

or damage to property.

1.6 To reduce the risk of damage to the electric plug or cord, pull by the

adaptor rather than the cord when disconnecting the unit.

1.7 Do not operate the unit with damaged cables or clamps.

1.8 Do not operate the unit if it has received a sharp blow, been dropped or

otherwise damaged in any way; take it to a qualied service person.

1.9 Do not disassemble the unit; take it to a qualied service person when

service or repair is required. Incorrect reassembly may result in a risk of

re or electric shock.

WARNING! RISK OF EXPLOSIVE GASES.

1.10 To reduce the risk of a battery explosion, follow these instructions and

those published by the battery manufacturer and the manufacturer of

any equipment you intend to use in the vicinity of the battery. Review

the cautionary markings on these products and on the engine.

1.11 Do not set the unit on ammable materials, such as carpeting,

upholstery, paper, cardboard, etc.

1.12 Never place the unit directly above battery being jumped.

1.13 Do not use the unit to jump start a vehicle while charging the internal battery.

Jump Starter/Power Pack

OWNER’S MANUAL

PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH

USE. This manual will explain how to use the unit safely and effectively.

Please read and follow these instructions and precautions carefully.

BASE MODEL

SL010

• 6 •

2. PERSONAL PRECAUTIONS

WARNING! RISK OF EXPLOSIVE GASES. A SPARK NEAR THE

BATTERY MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE

RISK OF A SPARK NEAR THE BATTERY:

2.1 NEVER smoke or allow a spark or ame in the vicinity of a battery or engine.

2.2 Remove personal metal items such as rings, bracelets, necklaces and

watches when working with a lead-acid battery. A lead-acid battery

can produce a short-circuit current high enough to weld a ring to

metal, causing a severe burn.

2.3 Be extra cautious, to reduce the risk of dropping a metal tool onto the

battery. It might spark or short-circuit the battery or other electrical

part that may cause an explosion.

2.4 Do not permit the internal battery of the unit to freeze. Never charge a

frozen battery.

2.5 To prevent sparking, NEVER allow clamps to touch together or

contact the same piece of metal.

2.6 Consider having someone nearby to come to your aid when you work

near a lead-acid battery.

2.7 Have plenty of fresh water, soap and baking soda nearby for use, in

case battery acid contacts your eyes, skin, or clothing.

2.8 Wear complete eye and body protection, including safety goggles and

protective clothing. Avoid touching your eyes while working near the

battery.

2.9 If battery acid contacts your skin or clothing, immediately wash

the area with soap and water. If acid enters your eye, immediately

ood the eye with cold running water for at least 10 minutes and get

medical attention right away.

2.10 If battery acid is accidentally swallowed, drink milk, the whites of eggs

or water. DO NOT induce vomiting. Seek medical attention immediately.

2.11 Neutralize any acid spills thoroughly with baking soda before attempting

to clean up.

2.12 This product contains a lithium ion battery. In case of re, you

may use water, a foam extinguisher, Halon, CO

, ABC dry chemical,

powdered graphite, copper powder or soda (sodium carbonate)

to extinguish the re. Once the re is extinguished, douse the

product with water, an aqueous-based extinguishing agent, or other

nonalcoholic liquids to cool the product and prevent the battery from

re-igniting. NEVER attempt to pick up or move a hot, smoking, or

burning product, as you may be injured.

• 7 •

3. PREPARING TO USE THE UNIT

WARNING! RISK OF CONTACT WITH BATTERY ACID. BATTERY

ACID IS A HIGHLY CORROSIVE SULFURIC ACID.

3.1 Make sure the area around the battery is well ventilated while the unit

is in use.

3.2 Clean the battery terminals before using the jump starter. During

cleaning, keep airborne corrosion from coming into contact with your

eyes, nose and mouth. Use baking soda and water to neutralize the

battery acid and help eliminate airborne corrosion. Do not touch your

eyes, nose or mouth.

3.3 Determine the voltage of the battery by referring to the vehicle

owner’s manual and make sure that the output voltage is 12V.

3.4 Make sure that the unit’s cable clamps make tight connections.

4. FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY

WARNING! A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:

4.1 Plug the clamps into the unit, and then attach the output cables to

the battery and chassis as indicated below. Never allow the output

clamps to touch each other.

4.2 Position the DC cables to reduce the risk of damage by the hood,

door and moving or hot engine parts. NOTE: If it is necessary to close

the hood during the jump starting process, ensure that the hood does

not touch the metal part of the battery clips or cut the insulation of the

cables.

4.3 Stay clear of fan blades, belts, pulleys and other parts that can cause injury.

4.4 Check the polarity of the battery posts. The POSITIVE (POS, P, +)

battery post usually has a larger diameter than the NEGATIVE (NEG,

N, -) post.

4.5 Determine which post of the battery is grounded (connected) to the

chassis. If the negative post is grounded to the chassis (as in most

vehicles), see step 4.6. If the positive post is grounded to the chassis,

see step 4.7.

4.6 For a negative-grounded vehicle, connect the POSITIVE (RED) clamp

from the jump starter to the POSITIVE (POS, P, +) ungrounded post

of the battery. Connect the NEGATIVE (BLACK) clamp to the vehicle

chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect

to a heavy gauge metal part of the frame or engine block.

4.7 For a positive-grounded vehicle, connect the NEGATIVE (BLACK)

clamp from the jump starter to the NEGATIVE (NEG, N, -) ungrounded

post of the battery. Connect the POSITIVE (RED) clamp to the vehicle

chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to

a heavy gauge metal part of the frame or engine block.

4.8 When nished using the jump starter, remove the clamp from the

vehicle chassis and then remove the clamp from the battery terminal.

Disconnect the clamps from the unit.

• 8 •

5. FEATURES

Qualcomm Quick Charge is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.

Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.

Quick Charge is a trademark of Qualcomm Incorporated. All Qualcomm Incorporated trademarks

are used with permission.

1. ON/OFF switch

2. Micro USB input port

for recharging

3. Qualcomm

Quick Charge

™

3.0 Technology

USB output port

4. 2.4A USB output port

Display button

6. LCD display

7. LED light

8. Jump start output socket

9. Battery clamps/smart cable

Not shown:

10. Micro USB-USB charging cable

11. Carrying bag

6. CHARGING THE JUMP STARTER

IMPORTANT! CHARGE IMMEDIATELY AFTER PURCHASE,

AFTER EACH USE AND EVERY 30 DAYS, OR WHEN THE

CHARGE LEVEL FALLS BELOW 85%, TO KEEP THE INTERNAL

BATTERY FULLY CHARGED AND PROLONG BATTERY LIFE.

6.1 CHECKING THE LEVEL OF THE INTERNAL BATTERY

1. Slide the ON/OFF switch to the ON position. The LCD display will show

the battery’s percentage of charge. A fully charged internal battery will read

100%. Charge the internal battery if the display shows it is under 85%.

2. To reduce the risk of electric shock, unplug the unit’s charging cable from

a USB or wall charger before attempting any maintenance or cleaning.

Simply turning off the controls will not reduce this risk.

3. When charging the internal battery, work in a well ventilated area and do

not restrict the ventilation in any way.

• 9 •

6.2 CHARGING THE INTERNAL BATTERY

NOTE: Use a 2A USB charger (sold separately), or a 2A USB

charging port to quickly recharge the jump starter. Using a charger

with less than 2A will increase charge time.

1. Plug the Micro USB end of the charging cable into the input port. Next,

plug the USB end of the charging cable into a charger’s USB port.

2. Plug your charger into a live AC or DC power outlet.

3. The LCD display will light, the digit begins to ash and show “IN”, indicating

that charging has begun.

4. The jump starter will fully charge in 4-5 hours. When the unit is fully

charged, the display will show “100%”.

5. When the battery is fully charged, disconnect your charger from the

outlet, and then remove the charging cable from the charger and the

unit. Slide the ON/OFF switch to the OFF position, if you are not using

the unit immediately.

7. OPERATING INSTRUCTIONS

7.1 JUMP STARTING A VEHICLE ENGINE

NOTE: Use only model number SA883 jump cable.

IMPORTANT: Do not use the jump starter while charging its internal battery.

IMPORTANT: Using the jump starter without a battery installed in the

vehicle will damage the vehicle’s electrical system.

NOTE: The internal battery must have a charge if at least 40% to

jump start a vehicle.

1. Turn the ignition OFF.

2. Plug the battery clamp cable into the jump starter’s output socket.

3. Lay the DC cables away from any fan blades, belts, pulleys and other

moving parts. Make sure all of the vehicle’s electrical devices are turned off.

4. For a negative-grounded vehicle, connect the POSITIVE (RED) clamp

from the jump starter to the POSITIVE (POS, P, +) ungrounded post

of the battery. Connect the NEGATIVE (BLACK) clamp to the vehicle

chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect

to a heavy gauge metal part of the frame or engine block.

5. For a positive-grounded vehicle, connect the NEGATIVE (BLACK)

clamp from the jump starter to the NEGATIVE (NEG, N, -) ungrounded

post of the battery. Connect the POSITIVE (RED) clamp to the vehicle

chassis or engine block away from the battery. Do not connect the

clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to

a heavy gauge metal part of the frame or engine block.

6. Slide the ON/OFF switch to the ON position. The green LED on the

smart cable should light.

NOTE: If the vehicle battery is extremely discharged, the initial current

draw from the jump starter may activate short circuit protection in the

smart cable. When the condition is corrected, the smart cable will

automatically reset.

7. After a proper connection has been made, crank the engine. If the engine

does not start within 5-8 seconds, stop cranking and wait at least 1 minute

before attempting to start the vehicle again.

• 10 •

NOTE: If the car does not crank a second time, check the smart cable to

see if the green LED is lit. If you hear beeping or an LED is ashing, refer

to section 10, Troubleshooting. When the condition is corrected, the

smart cable will automatically reset.

NOTE: Cold weather may affect the performance of the jump starter’s

lithium battery. If you hear only a click and the engine does not turn

over, try the following:

With the jump starter connected to the car battery and the green LED

illuminated on the smart cable, turn on all lights and electrical accessories

for one minute. This draws current from the jump starter and warms the

battery. Now try to crank the engine. If it does not turn over, repeat the

procedure. Extremely cold weather may require two or three battery

warmings before the engine will start.

NOTE: If no activity is detected, the smart cable will automatically shut

off after 120 seconds, and the red and green LEDs will be solid. To reset,

disconnect the clamps from the vehicle battery, and then reconnect.

IMPORTANT: DO NOT attempt to jump start your vehicle more

than three consecutive times. If the vehicle will not start after three

attempts, consult a service technician.

8. After the engine starts, unplug the battery clamps from the jump starter

socket and then disconnect the black clamp (-) and the red clamp (+),

in that order. Slide the ON/OFF switch to the OFF position.

9. Recharge the unit as soon as possible after each use.

7.2 CHARGING A MOBILE DEVICE, USING THE USB PORTS

The unit includes two USB ports. One provides up to 2.4A at 5V DC;

the other is Quick Charge 3.0, which provides up to 5V at 3A, 9V at 2A

or 12V at 1.5A.

1. Consult your mobile device manufacturer for proper charging power

specications. Connect a mobile device cable to the appropriate USB port.

2. Slide the ON/OFF switch to the ON position. Charging should begin

automatically. The display will show which port is in use.

3. Charging time will vary, based on the mobile device’s battery size and the

charging port used.

NOTE:

Most devices will charge with either USB port, but may charge

at a slower rate.

4. When nished using the USB port, disconnect the charging cable from

your mobile device and then disconnect the charging cable from the unit.

Slide the ON/OFF switch to the OFF position.

5. Recharge the unit as soon as possible after each use.

NOTE:

If no USB device is connected, power to the USB ports will

automatically shut off after 30 seconds.

• 11 •

7.3 USING THE LED LIGHT

1. Slide the ON/OFF switch to the ON position.

2. Hold down the display

button for 3 seconds.

3. Once the LED light is on, press and release the display

button to cycle

through the following modes:

• Steady glow

• Flash for an SOS signal

• Flash in strobe mode

4. When nished using the LED light, press and hold the display

button

until the light turns off.

5. Slide the ON/OFF switch to the OFF position.

6. Recharge the unit as soon as possible after each use.

8. MAINTENANCE INSTRUCTIONS

1. After use and before performing maintenance, unplug and disconnect

the unit.

2. Use a dry cloth to wipe all battery corrosion and other dirt or oil from

the battery clamps, cords, and the outer case.

3. Do not open the unit, as there are no user-serviceable parts.

9. STORAGE INSTRUCTIONS

1. Charge battery to full capacity before storage.

2. Store this unit at temperatures between

4°F-

140°F (

20°C-

60°C).

3. Never completely discharge the battery.

4. Charge after each use.

5. Charge at least once every month, if not in frequent use, to prevent

over-discharge.

10. TROUBLESHOOTING

Jump Starter

PROBLEM SOLUTION

The jump starter’s display will

not turn on.

Make sure the unit is charged.

Connect to a power source, to reset.

Make sure the ON/OFF switch is set to

the ON position.

The thermometer symbol

is ashing.

The unit is too hot or cold. The thermometer

symbol will disappear when the condition

is removed.

The jump starter will not

recharge.

Make sure the power source is live.

• 12 •

PROBLEM SOLUTION

The jump starter turns on, but

won’t jump start my vehicle.

Check connections.

Verify the charge level of the jump starter is

at least 40%.

Do not attempt to jump start your vehicle

more than three consecutive times. If

the vehicle still does not start, consult a

qualied service technician.

When cable is connected only

to the battery: Solid Red LED,

(Green LED off); beeps once

per second

The vehicle battery voltage is lower than

10.5V. User can connect to jump starter

and turn key to jump start the vehicle.

When cable is correctly

connected to both battery

and jump starter: Green LED

blinking; Red LED off; no beep.

“Fake” high battery voltage is detected,

but reverse charging protection did not

activate. User can turn key to jump start

the vehicle.

Smart Cable LED and Alarm Behavior

BEHAVIOR REASON

Green LED blinking; Red LED

off; no beep.

Cable is connected to battery only.

Cable is connected to jump starter only.

Green LED solid; Red LED off;

no beep.

Cable is connected correctly to both

battery and jump starter.

Solid Red LED, Green LED off;

beeps once per second

Low voltage protection

Solid Red LED, Green LED off;

beeps twice per second

Reverse polarity protection

Alternating Red and Green

ashing LEDs; no beep

Reverse charging protection

Solid Red LED, Green LED off;

rapid beeping

Short circuit protection

Solid Red and Green LEDs;

no beep.

Auto shut-off, due to inactivity. Disconnect

and reconnect clamps to the vehicle battery.

Solid Red and Green LEDs;

beeps once per second

Temperature protection

NOTE: When the condition is corrected, the smart cable will automatically reset.

• 13 •

11. BEFORE RETURNING FOR REPAIRS

If these solutions do not eliminate the problem,

or for more information about troubleshooting,

contact customer service for assistance:

[email protected]

www.batterychargers.com

or call 1-800-621-5485

For REPAIR OR RETURN, contact Customer Service at

1-800-621-5485. DO NOT SHIP UNIT until you receive a

RETURN MERCHANDISE AUTHORIZATION (RMA) number

from Customer Service at Schumacher Electric Corporation.

When returning an item, place the original package into a shipping

carton. If you received an emailed label from Schumacher, please

print the label and tape it to the carton. Only ship via insured

ground service with a tracking number. Return shipping

charges are the responsibility of the customer. We cannot accept

C.O.D. deliveries and are not responsible for lost or damaged

packages. Please do not place stickers or shipping labels on the

original manufacturer’s package. Please allow 2-3 days from date

we received the package for us to process your return. All return

shipping charges must be prepaid.

12. SPECIFICATIONS

Internal battery type .......................................... Lithium ion polymer

Capacity ................................................................................. 37 Wh

USB output .................................................................... 5V DC, 2.4A

Quick Charge 3.0: 5V, 3A / 9V, 2A / 12V, 1.5A

Jump start ................................................800A peak/400A cranking

Charging Temperature..................................... 32

-122

F (0

-50

13. REPLACEMENT PARTS

Battery clamps/smart cable ............................................ 94500883Z

Micro USB-USB charging cable ................................. 3899003781Z

• 14 •

14. LIMITED WARRANTY

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER

DRIVE, MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED

WARRANTY TO THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT.

THIS LIMITED WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this

jump starter for one (1) year from the date of purchase at retail against

defective material or workmanship that may occur under normal use

and care. If your unit is not free from defective material or workmanship,

Manufacturer’s obligation under this warranty is solely to repair or replace

your product, with a new or reconditioned unit, at the option of the

Manufacturer. It is the obligation of the purchaser to forward the unit, along

with proof of purchase and mailing charges prepaid to the Manufacturer or

its authorized representatives in order for repair or replacement to occur.

Manufacturer does not provide any warranty for any accessories used

with this product that are not manufactured by Schumacher Electric

Corporation and approved for use with this product. This Limited

Warranty is void if the product is misused, subjected to careless

handling, repaired, or modied by anyone other than Manufacturer or

if this unit is resold through an unauthorized retailer.

Manufacturer makes no other warranties, including, but not limited to,

express, implied or statutory warranties, including without limitation,

any implied warranty of merchantability or implied warranty of tness

for a particular purpose. Further, Manufacturer shall not be liable for

any incidental, special or consequential damage claims incurred by

purchasers, users or others associated with this product, including, but not

limited to, lost prots, revenues, anticipated sales, business opportunities,

goodwill, business interruption and any other injury or damage. Any and

all such warranties, other than the limited warranty included herein, are

hereby expressly disclaimed and excluded. Some states do not allow the

exclusion or limitation of incidental or consequential damages or length

of implied warranty, so the above limitations or exclusions may not apply

to you. This warranty gives you specic legal rights and it is possible you

may have other rights which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY

AND THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES

ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS

THE PRODUCT OTHER THAN THIS WARRANTY.

Schumacher

and the Schumacher logo are registered trademarks

of Schumacher Electric Corporation.

• 15 •

15. WARRANTY CARD

SAVE ON POSTAGE! ACTIVATE YOUR WARRANTY ONLINE –

THE QUICK AND EASY WAY!

Go to www.batterychargers.com to register your product online.

(No internet access? Send in the completed warranty card.)

1 YEAR LIMITED WARRANTY PROGRAM REGISTRATION

MODEL: _________________________________________

DESCRIPTION: ___________________________________

This is the only express limited warranty, and the manufacturer neither assumes nor authorizes anyone

to assume or make any other obligation. There is no other warranty, other than what is described in the

product owner’s manual.

The warranty card should be submitted within 30 days of purchase. The customer must keep the

ORIGINAL receipt because it will be required for any warranty claims.This warranty is not transferable.

Send warranty card only. DO NOT SEND UNIT TO THIS ADDRESS FOR REPAIR.

Mail this card to: Schumacher Electric Corporation

801 Business Center Drive

Mount Prospect, IL 60056-2179

Name _______________________________________________________________________________

Street address ________________________________________________________________________

City ________________________________State __________________ Zip code _________________

Phone ______________________________Email ___________________________________________

Name of store where purchased ____________________________ Date of purchase ________________

Store location ___________________________ UPC number __________________________________

Serial number (See Product) _____________________________________________________________

For faster warranty activation, go to www.batterychargers.com to register your product online.

• 16 •

1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD

GUARDE ESTAS INSTRUCCIONES.

ADVERTENCIA – RIESGO DE GASES EXPLOSIVOS.

TRABAJAR CERCA DE UNA BATERÍA DE PLOMO-ÁCIDO ES

PELIGROSO. LAS BATERÍAS GENERAN GASES EXPLOSIVOS

DURANTE SU FUNCIONAMIENTO NORMAL. ES IMPORTANTE QUE

SIGA LAS INSTRUCCIONES CADA VEZ QUE UTILICE LA UNIDAD.

Para disminuir el riesgo de explosión de la batería, siga estas

instrucciones, al igual que las recomendaciones publicadas por el

fabricante de la batería y de cualquier equipo que se utilizará cerca

de la batería. Verique las señales de advertencia que se hayan

colocado en estos productos y en el motor.

ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA O INCENDIO.

1.1 Lea el manual completo antes de utilizar este producto. Cualquier falla

podría resultar en serias lesiones o podría ser mortal.

1.2 Manténgase alejado de los niños.

1.3 No coloque los dedos o las manos en cualquiera de salidas de la unidad.

1.4 No exponga la unidad a la lluvia o la nieve.

1.5 Utilice solamente accesorios recomendados (SA883 cable de arranque).

El uso de un accesorio no recomendado o suministrado por el fabricante

del arrancador para la unidad puede provocar riesgo de incendio,

descarga eléctrica o lesiones a personas o daño a la propiedad.

1.6 Para reducir el riesgo de daños al enchufe o cable eléctrico, jale del

adaptador en lugar de jalar del cable al desconectar la unidad.

1.7 No utilice la unidad si el mismo posee los cables o las pinzas dañado.

1.8 No utilice la unidad si el mismo recibió un golpe fuerte, si se cayó o si

sufrió daños de cualquier otra forma; hágalo revisar por una persona

capacitada que efectúe reparaciones.

1.9 No desarme la unidad; hágalo revisar por una persona capacitada que

efectúe reparaciones cuando necesite servicio de mantenimiento o una

reparación. Volver a ensamblar la unidad en forma incorrecta puede

provocar riesgo de incendio o descarga eléctrica.

ADVERTENCIA: RIESGO DE GASES EXPLOSIVOS.

1.10 Para reducir el riesgo de explosión de una batería, siga estas instrucciones

y aquellas publicadas por el fabricante de la batería y por el fabricante de

cualquier equipo que intente utilizar en la proximidad de la batería. Revise

las pautas de precaución en estos productos y en el motor.

1.11 No coloque la unidad sobre materiales inamables como alfombras,

tapicería, papel, cartón, etc.

Arrancador / Pack de energía

MANUAL DEL USUARIO

POR FAVOR GUARDE ESTE MANUAL DEL PROPIETARIO Y LEER ANTES

DE CADA USO. En este manual se explica cómo utilizar la unidad segura

y efectiva. Por favor, lea y siga las siguientes instrucciones y precauciones.

MODELO BASE

SL010

• 17 •

1.12 Nunca coloque la unidad directamente sobre la batería que se iniciará.

1.13 No use la unidad arrancar con un vehículo mientras se carga la

batería interna.

2. PRECAUCIONES DE SEGURIDAD PERSONAL

ADVERTENCIA: RIESGO DE GASES EXPLOSIVOS. UNA CHISPA

CERCA DE LA BATERÍA HACER QUE LA BATERÍA EXPLOTE. PARA

REDUCIR EL RIESGO DE CHISPAS CERCA DE LA BATERÍA:

2.1 NUNCA fume o permita la presencia de chispas o llamas en la

proximidad de una batería o motor.

2.2 No utilice elementos personales de metal tales como anillos, pulseras,

collares y relojes al trabajar con una batería de plomo-ácido. Una

batería de plomo-ácido puede producir una corriente de cortocircuito lo

sucientemente elevada como para soldar un anillo o provocar efectos

similares sobre el metal, causando una quemadura de gravedad.

2.3 Tenga especial cuidado para reducir el riesgo de dejar caer una

herramienta de metal sobre la batería. Esto podría provocar chispas

o un cortocircuito en la batería o en cualquier otra pieza eléctrica que

podría provocar una explosión.

2.4 No deje que la batería interna se congele. Nunca cargue una batería

congelada.

2.5 Para prevenir cortos, NUNCA permita que las pinzas se junten o

hagan contacto por medio de un mismo metal.

2.6 Considere la idea de que alguna persona se encuentre cerca suyo

para poder ayudarlo cuando trabaje en forma cercana a una batería

de plomo-ácido.

2.7 Cuente con una gran cantidad de agua potable y jabón a mano en caso

de que el ácido de la batería tenga contacto con su piel, ropa u ojos.

2.8 Utilice protección visual y corporal completa, incluyendo gafas de

seguridad y prendas de protección. Evite tocar sus ojos mientras

trabaje en forma cercana a la batería.

2.9 Si el ácido de la batería tiene contacto con su piel o su ropa, lave de

inmediato el área afectada con agua y jabón. En caso de que ingrese ácido

en un ojo, sumerja el mismo de inmediato bajo agua potable corriente por

al menos 10 minutos y obtenga atención médica en forma inmediata.

2.10 Si el ácido de la batería es accidentalmente ingerido, se recomienda

beber leche, clara de huevo o agua. NO provoque vómito. Busque

ayuda médica de inmediato.

2.11 Neutralice el ácido derramado abundantemente con bicarbonato de

sodio antes de intentar limpiarlo.

2.12 Este producto contiene una batería de ión-litio. En caso de incendio,

puede utilizar agua, extintor de espuma, halón, CO

polvo químico seco

ABC, grato en polvo, polvo de cobre o soda (carbonato de sodio) para

extinguir el fuego. Una vez que el fuego se haya extinguido, empape

el producto con agua, un agente de extinción basado en agua u otros

líquidos sin alcohol para enfriar el producto y evitar que la batería se

vuelva a encender. NUNCA intente levantar o mover un producto caliente,

que emita humo o que esté en llamas, ya que puede resultar herido.

• 18 •

3. PREPARACIÓN PARA EL USO

ADVERTENCIA: RIESGO DE EXPLOSIÓN Y DE CONTACTO CON EL

ÁCIDO DE LA BATERÍA. EL ÁCIDO DE LA BATERÍA ES UN ÁCIDO

SULFÚRICO ALTAMENTE CORROSIVO.

3.1 Asegúrese de que el área alrededor de la batería esté bien ventilada

mientras la unidad está en uso.

3.2 Limpie los terminales de la batería antes de usar el arrancador.

Durante la limpieza, evite que la corrosión producida por aire tenga

contacto con sus ojos, nariz y boca. Utilice bicarbonato de sodio y

agua para neutralizar el ácido de la batería y ayudar a eliminar la

corrosión producida por aire. No toque ojos, nariz o boca.

3.3 Determine el voltaje de la batería consultando el manual del usuario

del vehículo y asegúrese de que la tensión de salida es de 12V.

3.4 Asegúrese de que las pinzas de la unidad se encuentren rmemente

conectadas.

4. SIGA ESTOS PASOS CUANDO SE CONECTE A LA BATERÍA

ADVERTENCIA: UNA CHISPA PROVOCADA CERCA DE LA BATERÍA

PUEDE CAUSAR LA EXPLOSIÓN DE LA BATERÍA. PARA REDUCIR EL

RIESGO DE PROVOCAR CHISPAS CERCA DE LA BATERÍA:

4.1 Conectar las pinzas a la unidad, y luego conecte los cables de salida

a la batería y al chasis según lo indicado abajo. Nunca permita que las

pinzas hagan contacto una con el otra.

4.2 Ubique los cables de C.C. para reducir el riesgo de daños a la cubierta,

a la puerta y a las piezas móviles o calientes del motor. NOTA: Si es

necesario cerrar el cofre durante el proceso de arranca, asegúrese que

el cofre no toque parte metálica de la batería o pele los cables.

4.3 Manténgase alejado de las paletas del ventilador, correas, poleas y

otras piezas que podrían provocar lesiones.

4.4 Verique la polaridad de los bornes de la batería. El borne POSITIVO

(POS, P, +) de la batería generalmente posee un diámetro mayor al

borne NEGATIVO (NEG, N, -).

4.5 Determine qué borne de la batería hace descarga a tierra (se

encuentra conectado) con el chasis. Si el borne negativo hace

descarga a tierra con el chasis (como en la mayor parte de los

vehículos), ver el paso 4.5. Si el borne positivo hace descarga a

tierra con el chasis, ver el paso 4.6.

4.6 En un vehículo con descarga a tierra por borne negativo, conecte el

gancho POSITIVO (ROJO) desde el arrancador al borne POSITIVO

(POS, P, +) sin descarga a tierra de la batería. Conecte el gancho

NEGATIVO (NEGRO) al chasis del vehículo o al bloque motor alejado

de la batería. No conecte el gancho al carburador, líneas de combustible

o cuerpos metálicos. Conecte a una pieza metálica de calibre grueso

del marco o del bloque motor.

• 19 •

4.7 En un vehículo con descarga a tierra por borne positivo, conecte el

gancho NEGATIVO (NEGRO) desde el al borne NEGATIVO (NEG, N, -)

sin descarga a tierra de la batería. Conecte el gancho POSITIVO

(ROJO) al chasis del vehículo o al bloque motor alejado de la batería.

No conecte al carburador, líneas de combustible o cuerpos metálicos.

Conecte a una pieza metálica de calibre grueso del marco o del

bloque motor.

4.8 Cuando termine de usar el arrancador, retire la pinza del chasis

del vehículo y quite la abrazadera de la terminal de la batería.

Desconecte las pinzas desde la unidad.

5. CARACTERÍSTICAS

1. Interruptor ON/OFF

2. Puerto de entrada Micro USB

para recargar

3. Puerto de salida de USB

Qualcomm

Quick Charge™

3.0 Tecnología

4. Puerto USB – 2,4A

Botón de pantalla

6. Pantalla LCD

7. Luz LED

8. Toma de salida del arrancador

9. Pinzas de la batería/

cable inteligente

No mostrada:

10. Cable de carga micro USB-USB

11. Bolsa de transporte

Qualcomm Quick Charge es un producto de Qualcomm Technologies, Inc. y / o sus subsidiarias.

Qualcomm es una marca registrada de Qualcomm Incorporated, registrada en los Estados Unidos

y otros países.

Quick Charge es una marca comercial de Qualcomm Incorporated. Todas las marcas registradas

de Qualcomm Incorporated se utilizan con permiso.

• 20 •

6. CARGAR EL ARRANCADOR

IMPORTANTE: CARGUE LA UNIDAD INMEDIATAMENTE DESPUES

DE COMPRARLA, DESPUES DE CADA USO Y CADA 30 DÍAS,

O CUANDO EL NIVEL DE CARGA CAE POR DEBAJO DEL 85%,

PARA MANTENER LA BATERÍA INTERNA COMPLETAMENTE

CARGADA Y PROLONGAR LA VIDA DE LA BATERÍA.

6.1 COMPROBACIÓN DEL NIVEL DE LA BATERÍA INTERNA

1. Deslice el interruptor ON / OFF a la posición ON. La pantalla LCD

mostrará el porcentaje de la carga de la batería. Una batería interna

completamente cargada leerá 100%. Cargue la batería interna si la

pantalla muestra que está bajo 85%.

2. Para reducir el riesgo de descarga eléctrica, desconecte el cable de

carga de la unidad desde un cargador USB o de pared antes de intentar

cualquier mantenimiento o limpieza. Simplemente apagar los controles

no reducirá este riesgo.

3. Cuando la carga de la batería interna, trabajar en un área bien

ventilada y no restringir la ventilación de ninguna manera.

6.2 CARGANDO LA BATERÍA INTERNA

NOTA: Utilice un cargador USB de 2A (se vende por separado), o un

puerto de carga USB de 2A para recargar rápidamente el arrancador.

El uso de un cargador con menos de 2A aumentará el tiempo de carga.

1. Conecte el extremo Micro USB del cable de carga en el puerto de

entrada. A continuación, conecte el extremo USB del cable de carga en

el puerto USB de un cargador.

2. Conectar el cargador a una toma de alimentación de CA o CC en vivo.

3. La pantalla LCD se iluminará, el dígito comenzará a parpadear y

mostrará “IN”, indicando que la carga ha comenzado.

4. El arrancador cargará completamente en 4-5 horas. Cuando la batería

interna está completamente cargada, la pantalla mostrará “100%”.

5. Cuando la batería esté completamente cargada, desconecte el

cargador de la toma de corriente y, a continuación, retire el cable de

carga del cargador y de la unidad. Deslice el interruptor ON / OFF a la

posición OFF, si no está utilizando la unidad inmediatamente.

6. Cargue la unidad tan pronto sea posible, después de usarse.

7. INSTRUCCIONES DE OPERACIÓN

7.1 ARRANCAR UN MOTOR DE VEHÍCULO

NOTA:

Utilizar sólo el cable de arranque auxiliar modelo SA883.

IMPORTANTE: No utilice el arrancador mientras se carga su batería interna.

IMPORTANTE: Utilización de la función arranque del motor sin una batería

instalada en el vehículo dañará el sistema eléctrico del vehículo.

NOTA: La batería interna debe tener un cargo si al menos el 40%

para iniciar un vehículo.

1. APAGUE el motor.

2. Conecte el cable de las pinzas de la batería a la toma de salida del

arrancador.

La page est en cours de chargement...

Schumacher SL1327SL1327 Le manuel du propriétaire

Marque: Schumacher

Modèle: SL1327SL1327

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Schumacher SL1327SL1327 Owner's manual
español: Schumacher SL1327SL1327 El manual del propietario

Schumacher SL1327SL1327 Le manuel du propriétaire

Ce manuel convient également à

Schumacher SL1327SL1327 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents