peak design Peak-Design 2AZ94MCMAA Wireless Charging Car Mount Manuel utilisateur

Taper
Manuel utilisateur
Revision Number (date) - revisions
r0 (210818)
REVISIONS
ARTWORK
M-INS-EUW-1 | COMPLIANCE INFO CARD | r0 210818
FCC compliance statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment
and receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
ISED compliance statement
This device contains licence-exempt transmit-
ter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-ex-
empt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
Lémetteur/récepteur exempt de licence contenu
dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio
exempts de licence. Lexploitation est autorisée aux
deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
RF Exposure Compliance
This equipment complies with FCC/IC RSS-102
radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20 cm
between the radiator and your body.
Cet équipement est conforme aux limites
d’exposition aux radiations FCC/IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur et
votre corps.
EU
110.08-129.26kHz, H-field: -8.89dBuA/m@10m
Hereby, Peak Design declares that the radio
equipment type M-CM-AA-BK-1, M-CM-AD-BK-1
and M-CS-BK-1 are in compliance with Directive
2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet
address: https://www.peakdesign.com/EU-certifica-
tion
Hereby, Peak Design declares that the radio
equipment type M-CM-AA-BK-1, M-CM-AD-BK-1
and M-CS-BK-1 are in compliance with UK Radio
Equipment Regulations (SI 2017/1206). The full text
of the declaration of conformity is available at the
following internet address: https://www.peakde-
sign.com/EU-certification
COMPLIANCE INFO
  • Page 1 1

peak design Peak-Design 2AZ94MCMAA Wireless Charging Car Mount Manuel utilisateur

Taper
Manuel utilisateur