Smeg LSIA147 Manuel utilisateur

LAVASCIUGA

WASHER-DRYER

LAVE-LINGE SÉCHANT

VOLLWASCHTROCKNER

LAVADORA-SECADORA

LIBRETTO ISTRUZIONI

IT

INSTRUCTION MANUAL

EN

MANUEL D'INSTRUCTIONS

FR

GEBRAUCHSANLEITUNG

DE

MANUAL DE INSTRUCCIONES

ES

1

Contents

1. PRECAUTIONS FOR SAFETY AND USE ................................................................................... 2

2. INSTALLATION INSTRUCTIONS ............................................................................................... 7

3. DESCRIPTION OF CONTROLS ................................................................................................. 12

4. USING THE APPLIANCE FOR WASHING ............................................................................... 13

5. USING THE APPLIANCE FOR DRYING .................................................................................. 21

6. CLEANING AND MAINTENANCE ........................................................................................... 23

7. TROUBLESHOOTING ................................................................................................................. 25

8.INFORMATION FOR THE USER ........................................................................................... 27

This appliance is tagged in accordance with European Directive 2012/19/EU on

Waste Electrical and Electronic Equipment - WEEE.

This directive contains the regulations governing the collection and recycling of de-

commissioned appliances throughout the European Union.

The symbol of the rubbish bin with a line through it on the appliance or its packaging

indicates that the product must be disposed of separately from other waste at the end

of its life cycle. The user is thus obliged to consign scrapped appliances to the special

electronic and electrotechnical waste disposal centres, or return them to the dealer

on purchase of a similar new appliance, on a one-to-one basis.

Consignment to the appropriate facility for environmentally responsible recycling,

treatment and disposal helps to prevent any negative effects on the environment and

health, and encourages the reuse and/or recycling of the appliance’s component ma-

terials.

Illegal dumping of the appliance by the user will be subject to prosecution under the

relevant law.

EN

2

READ THE INSTRUCTIONS

Attention!

You are advised to read all the instructions in this manual carefully; it will inform you

about the right conditions for the proper, safe use of your washer-dryer

It is very important to keep this instruction manual with the appliance for future ref-

erence.

In the event of sale or transfer, ensure that the manual always accompanies the

appliance, to provide the necessary information about its use.

1. PRECAUTIONS FOR SAFETY AND USE

Attention!

These precautions are detailed for reasons of safety.

This section must be read carefully before installation and use.

Disposing of packaging

 Never leave packaging residues unattended in the home. Separate waste

packaging materials by type and consign them to the nearest recycling cen-

tre.

 Packaging materials (plastic bags, polystyrene, etc.) must not be left within

reach of children.

Disposing of old appliances

 Once no longer in use, appliances must be rendered unusable: perma-

nently disarm the lock on the door (this will prevent children risking

their lives by locking themselves inside during play) and cut the power

supply lead after removing the plug from the socket.

The appliance must be delivered to a recycling facility.

Environmental protection

 Use the whole of the maximum recommended capacity. Never exceed the

maximum permitted load.

 Do not use the prewash function for lightly or normally soiled items.

 Follow the manufacturer's recommendations on detergent usage.

 Use the highest spin speed permitted for the fabric type. Fast spins reduce

the drying time and thus energy consumption.

 Programs that work with lower temperatures are the most efficient in terms of

energy consumption. We therefore recommend that you to make a note of

the information on the labels on the items to be washed and provided by the

manufacturer. This will mean that the temperatures and detergent doses will

be optimized to avoid excessive energy consumption

 It is recommended to follow the instructions provided in the manual, and those

provided by the manufacturers of the detergents, softeners and additives (sol-

vents, degreasers, stain remover additives…) for their correct use and dos-

age. Failure to comply with the recommendations provided may damage the

appliance.

EN

3

 WARNING: the higher the spin speed, the higher will be the noise and the

lower the remaining moisture content. The lower the amount of residual

moisture at the end of the wash, the lower the energy consumption will be

during drying.

 Information on household detergents, additives and cleaning agents can be

found on the following website www.cleanright.eu .

Safety instructions

 This appliance is intended for domestic use and similar applications such as

staff kitchen area in shops, offices and other working environments, farm

houses, and for the use by clients in hotels, motels, bed and breakfast type

environments, and other residential facilities and is compliant with Directives

2014/35/EU and 2014/30/EU currently in force.

 Read all the instructions in this manual carefully before installation and use.

 Check that the drum assembly has been released before use (see instruc-

tions). Failure to release the drum assembly may cause damage to the

washer-dryer and the surrounding furniture or appliances during the spin cy-

cle.

 This Instruction Manual is an integral part of the appliance: it must always be

kept intact with the appliance. Installation must be carried out by qualified

staff in compliance with the relevant regulations. The appliance is built to pro-

vide the following functions: washing and drying of clothes or fabrics stated

to be suitable for machine washing by the producer on the relevant label. All

other uses are to be considered improper. The manufacturer declines all

liability for uses other than those stated above.

 The nameplate with the technical data, serial number and mark is in a visible

position in the part in view after the door has been opened. The nameplate

must never be removed.

 The electrical and plumbing works required to install the appliance

must only be carried out by skilled staff.

 The appliance must be connected to earth in compliance with electrical sys-

tem safety regulations. The manufacturer declines all liability for direct

or indirect injury or damage deriving from a non-existent or defective

earth connection.

 In the event that the appliance is not connected by means of a plug, an om-

nipolar circuit-breaker device with contact gap of at least 3 mm must be pro-

vided.

 The plug to be connected to the power supply lead and the relative socket

must be of the same type and comply with the relevant regulations. Check

that the mains voltage and frequency are the same as the values marked on

the nameplate. The use of adapters or junctions is not recommended. Never

disconnect the plug by pulling on the power supply lead.

 The appliance is only disconnected from the electricity supply if the

plug has been removed from the socket or the electrical system master

switch has been turned off. The power plug must be accessible after

the appliance has been installed.

EN

4

 WARNING: The appliance must not be supplied through an external switch-

ing device, such as a timer, or connected to a circuit that is regularly switched

on and off by a utility.

 The appliance must be installed using new sets of hoses (supplied with the

appliance). Old hose sets should not be reused.

 Take care that the appliance is not standing on the power supply cable.

 The washer-dryer must never be used on vehicles, on board ships or planes,

or in environments with hazards, such as explosive or corrosive environ-

ments (powders, vapours and gases) or explosive and/or corrosive liquids,

 Do not install the washer-dryer in places with a risk of frost. Frozen pipes may

burst under the pressure.

 Make sure that the drain hose connected to the sink is securely fastened

and cannot move.

 If it is not fixed in place, the repulsive force of the water might thrust it away

from the sink, causing the risk of flooding.

 When connecting the hose to a sink also check that the water drains from

it quickly, as otherwise the sink may overflow.

 Do not overload the appliance.

 Never use detergents which contain solvents or chemicals for washing in the

washer-dryer. They might damage the appliance and form poisonous va-

pours. These fumes might also catch fire and explode.

 Garments soaked in petroleum products must not be washed in the washing

machine. Before washing, check that garments do not contain inflammable

devices (e.g. cigarette-lighters, matches, etc.)

 If volatile cleaning fluids are used, ensure that these substances have been

removed from the garments before they are placed in the appliance.

 Before loading garments for washing, check that the pockets are empty, but-

tons secure and zips fastened.

 Do not wash frayed or torn garments.

 During washing at high temperatures, the glass in the door will become very

hot.

 Check that all water has been drained from the appliance before open-

ing the door.

 If there is water inside, pump it out before opening the door. If in doubt, read

the instruction manual.

 The water in the appliance is not suitable for drinking!

 Swallowing washing machine detergents may injure the mouth and throat.

 Before removing the garments from the washer-dryer check that the drum

is at a standstill.

 Switch the appliance off after each use to avoid wasting electricity.

 Leave the door ajar between washes to keep the gasket in good condition.

 In the event of a malfunction never attempt to repair the appliance your-

self. Disconnect the appliance from the electricity supply and turn off the wa-

ter tap. Then contact a qualified engineer. Repairs must only be carried

out by qualified staff.

EN

5

 The appliance is intended for use by adults. Do not allow children to tam-

per with the washer-dryer's controls or play with it and do not keep children

in the vicinity while the programme is in progress.

 Young animals or small children might climb into the washer-dryer .

 Always check the inside of the drum before use and do not allow children

to play with the appliance.

 Keep children away from the appliance when the door or the detergent

drawer is open; the appliance might contain detergent residues which may

cause permanent injury to the eyes, mouth and throat, or even cause death

by suffocation.

 This washing machine / washer dryer, must be used by adults. Use of the

appliance by children aged from eight years and a person with reduced phys-

ical sensory or mental capabilities or lack of experience and knowledge is

only permitted under the supervision of a person responsible for their safety.

 The appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their safety.

 That the tumble dryer is not to be used if industrial chemicals have been used

for cleaning

 That lint must not be allowed to accumulate around the tumble dryer

 Do not dry unwashed items in the tumble dryer

 Items that have been soiled with substances such as cooking oil, acetone,

petrol, kerosene, spot removers, turpentine, waxes and wax removers should

be washed in hot water with an extra amount of detergent before being dried

in the tumble dryer

 Items such as foam rubber (latex foam), shower caps, waterproof textiles,

rubber backed articles and clothes or pillows fitted with foam rubber pads

should not be dried in the tumble dryer

 Fabric softeners, or similar products, should be used as specified by the fab-

ric softener instructions.

 The final part of a tumble dryer cycle occurs without heat (cool down cycle)

to ensure that the items are left at a temperature that ensures that the items

will not be changed

 Never stop a tumble drier before the end of the drying cycle unless all items

are quickly removed and spread out so that the heat is dissipated

 Do not store flammable fluids near the appliance.

Lengthy periods out of use.

 If the appliance is not to be used for a lengthy period it should be discon-

nected from the electricity and water supplies and the door should be left ajar

to prevent unpleasant smells from building up inside.

Important!

This appliance is easy to use.

However, for the best results it is important to read this manual carefully and

follow all the instructions before putting it into operation.

The manual provides the correct instructions for installation, use and mainte-

nance, as well as giving useful advice.

EN

6

For Great Britain only

Warning: this appliance must be earthed.

Fuse replacement

If the mains lead of this appliance is fit-

ted with a BS 1363A 13amp fused plug,

to change a fuse in this type of plug use

an A.S.T.A. approved fuse to BS 1362

type and proceed as follows:

1. Remove the fuse cover (A) and

fuse (B)

2. Fit replacement 13A fuse into

fuse cover

3. Refit both into plug

Important:

The fuse cover must be refitted when

changing a fuse and if the fuse cover is

lost the plug must not be used until a

correct replacement is fitted.

Correct replacement are identified by

the colour insert or the colour em-

bossed in words on the base of the

plug.

Replacement fuse covers are available

from your local electrical store.

If the appliance is provided with a plugless supply cord:

 It is necessary to install in the fixed wiring an all-pole disconnection device

having a gap between contacts of at least 3,5mm. After installation the

disconnection device has to be easy to reach.

 The connection to the mains must be carried out by a qualified technician

in accordance to the scheme shown below and the regulations in force

L = brown

N = blue

= yellow-green

 In the event of damage to the supply cord, it has to be replaced by the

manufacturer or an authorized technical service center in order to avoid

any risk.

The manufacturer declines all responsibility for injury or damage caused

by failure to comply with the above regulations or deriving from tampering with

even just one part of the appliance and the use of non-original spare parts.

EN

7

2. INSTALLATION INSTRUCTIONS

Important!

The appliance must be installed by a qualified engineer in compliance with

the relevant regulations.

The washer-dryer is heavy. Take care when lifting it.

2.1 UNPACKING

The unit on flexible mounts is fixed in place for transport using the screws (A)

on the rear of the washer-dryer, with the relative plastic spacers (B). Once the

screws have been removed, the power supply lead can be used.

1. Undo all the screws with a 10 mm spanner

2. Remove all the screws (A) from the rear

3. Remove all the plastic spacers (B)

WARNING: It is absolutely necessary to fit all (nr.5)

the supplied plastic plugs (C) in order to avoid

splashes or water penetrating the machine or to

avoid contact with live parts.

Warning!

 Do not turn the appliance upside-down or place it on its sides.

 All the transport retainer fittings should be kept in a safe place; they must be

fitted again if the appliance has to be moved around in the future.

A+B

A

B

C

EN

8

2.2 POSITIONING AND LEVELLING

1. Place the appli-

ance in the chosen

position.

2. Level the appli-

ance carefully in all

directions with the

aid of a spirit level,

adjusting the height

of the feet if neces-

sary. Once done, fix

the feet in place with the locknuts provided.

3. On appliances with adjustable rear feet, note that the rear of the appliance

rests on skids and not on the feet. Before inserting the appliance into its place

between the kitchen units, check that the rear feet are screwed fully in to pre-

vent damage as the appliance is shifted into position.

Once the appliance is in position in the kitchen, the height of the rear feet has

to be increased so that the appliance no longer stands on the skids. After

adjusting the rear feet, level the appliance and fix the front feet at the height

required.

The water intake and drain hoses can be fitted pointing to the left or right for

effective installation.

EN

9

Warning!

 This operation must be carried out with care to prevent the washer-

dryer from vibrating, moving or generating excessive noise during use.

 If the appliance is installed on a carpeted floor, take care to ensure

that the openings in the bottom of the washer-dryer are not obstructed.

 Also check that during operation the washer-dryer is not resting against

walls, kitchen units, etc.

 The appliance must not be installed behind a door with lock, a sliding door, or

a door with hinge on the opposite side.

2.3 CONNECTING TO THE WATER SUPPLY

1. Check that the water supply pressure is in the follow-

ing range: 0,05-0,9MPa. With higher pressures, use a

pressure reducer.

2. Connect the cold water supply hose (blue screw

collar) to the cold water tap with ¾ gas threaded con-

nector, taking care to tighten firmly to prevent leaks.

The water supply hose must not be kinked or crushed

and must not be changed or cut. Threaded connections

must only be tightened by hand.

3. When appliances are supplied with hot water, the intake water temperature

must not exceed 60°C and the hose with red screw collar must be connected

to the hot water supply tap.

Warning!

 If the connection is made to new pipelines, or lines which have been out

of use for a long time, allow a considerable amount of water to flow out be-

fore connecting the intake hose. This prevents any sand or other dirt from

fouling the filters installed in the appliance to protect the water intake valves.

 The new intake hose supplied with the appliance must be used, and the old

water supply hose must not be used.

Supplementary note regarding the water connection for the German mar-

ket.

Before connecting the product to the water supply, make sure that the water

system has been fitted with a safety device to protect drinking water against

contamination due to backflow (according to DIN EN 1717). The water valves

and/or taps are fitted with these safety devices if the water system of the house

has been properly implemented.

EN

1

0

2.4 CONNECTING TO THE DRAIN

1. Insert the end of the drain hose into a drain pipe having inside diameter of

at least 4 cm, at least 50 to 90 cm above floor level, or connect it securely

(using the plastic fitting on the elbow in the hose) to a sink or bathtub.

2. In all cases, check that the end of the drain hose is securely fixed to prevent

the repulsive force of the water from pushing it out of place.

Warning!

 Avoid kinks or restrictions to ensure effective drainage.

 Any drain hose extensions must be no more than 1 metre long, must be of

the same diameter and must be free from restrictions of all kinds.

 The end of the drain hose must never be submerged in water.

EN

11

2.5 ELECTRICAL CONNECTION

Before connecting the plug to the power socket ensure that:

1. The electrical system voltage is the same as that stated on the nameplate

on the front of the appliance, in the zone visible when the door is open.

The rated power supply and the fuses required are specified on the name-

plate.

2. The meter, safety breakers, power supply line and power socket are rated

to withstand the maximum load required, stated on the nameplate.

3. The power supply socket and the plug fitted to the appliance are compat-

ible without the use of reductions, multiple sockets, adapters and exten-

sion leads which might cause overheating or scorching.

If the power supply socket is not compatible with the plug supplied, re-

place the socket with one of the appropriate type.

Warning

 The power plug must be accessible after the appliance has been installed.

 It is absolutely essential to connect the appliance to earth. Connect

the plug to a socket with an earth connection in good working order.

The manufacturer declines all liability for direct or indirect injury or dam-

age deriving from a non-existent or defective earth connection. Correct

electrical connection guarantees conditions of maximum safety.

 This appliance is compliant with the requirements of EEC directive 89/336

of 3.5.89 (including the amendment directive 92/31/EEC) concerning the

elimination of radio-frequency disturbance.

 If the power supply lead is damaged, it must only be replaced with an orig-

inal spare, available from the After-Sales Service.

 Do not connection/disconnect the power supply plug from the socket

with wet hands

 Only disconnect the power supply plug from the socket by taking

hold of the plug itself, never by pulling on the lead.

EN

1

2

3. DESCRIPTION OF CONTROLS

3.1 CONTROL PANEL

All the appliance's control and monitoring devices are placed together on the front panel.

Programme Selector

For switching the washer-dryer

on and off and selecting pro-

grammes. Can be turned in ei-

ther direction. Does not turn

while programmes are in pro-

gress.

Start/Pause button:

For starting and stopping

working cycles.

Display: shows the settings (spin speed, cycle status, flexi time, maximum recommended weight,

drying levels, child lock, clean programme). The settings can be modified using the buttons under-

neath.

Buttons (from left to right):

Washing Temperature selection

Spin speed selection

Option selection

Confirm option

Time to end

Drying

EN

13

4. USING THE APPLIANCE FOR WASHING

4.1 PREPARING THE ITEMS FOR WASHING

1. Subdivide the items for washing by fabric type and colour fastness.

2. Wash white and coloured items separately. New coloured items should be washed separately the first time.

Normally, items carry labels with washing instructions. The following is a short description of the symbols used

on these labels.

WASHING BLEACHING

Machine wash at max. 90°C

Bleaching allowed

Do not bleach

Machine wash at max. 60°C

IRONING

Machine wash at max. 40°C

Hot iron

Warm iron

Cool iron

Do not iron

Machine wash at max. 30°C

DRY CLEANING

Machine wash, delicate cycle

at max. 60°C

Any solvent

Any solvent ex-

cept trichloroe-

thylene

Petroleum sol-

vent and R113

Do not dry clean

Machine wash, delicate cycle

at max. 40°C

Machine wash, delicate cycle

at max. 30°C

DRYING

Hand wash

High tem-

perature

Less than 60°C

Do not tumble dry

Do not wash

Warning!

 Do not wash unhemmed or torn items as they may fray.

 Unrelated items in the wash may damage the garments or parts of the washer-dryer. So: empty pockets and

turn them inside-out, and remove wheels from curtains or wrap them in a mesh bag.

 Wash very small items (belts, handkerchiefs, socks, padded bras, etc.) in a white canvas bag. Fasten press-

studs and zips and sew on loose buttons.

 The use of modern detergents and the correct washing temperature is generally sufficient to remove stains

from fabrics. However, some difficult stains such as grass, fruit, egg, blood, rust, ballpoint pen, etc. should be

dealt with before washing. Depending on the type of fabric, there are a large number of commercial stain

removers on the market. In all cases, stains should be cleaned or diluted at once, since the older they

are, the harder they are to remove.

 Failure to comply with washing guidance symbols may result in damage to the items washed.

Wool – Only wool marked as pure new wool, with the mark, or labelled "shrink-proof, machine-washable" can

be washed in a washing machine on the specific programme; other types of wool should be hand-washed or dry-

cleaned.

4.2 OPENING THE DOOR

The appliance is fitted with a safety device which prevents the door from being opened while the programme is in

progress.

1. Check that all the water has been drained from the tank and the drum is at a standstill.

Warning!

 If the washing programme is interrupted, it will be from 3 to 15 minutes before the door can be opened,

depending on the temperature reached inside the appliance.

Warning!

The water may still be boiling hot if the wash was at high temperature.

Do not open the door if there is still water in the drum!

4.3 LOADS OF WASHING

As far as possible, to save electricity, it is more economical to wash complete loads of the various types of

fabric. Shake out the laundry before loading, and alternate large and small items. It is best to weight the load the

first few times, after which you will be able to rely on your experience.

EN

14

4.4 LOADING THE ITEMS FOR WASHING

1. Open the door and load the laundry, distributing it evenly over the drum, with items opened out and not

bundled together; if possible, large and small items should be well mixed.

2. The washing machine covered by this manual can be loaded with up to 7kg of laundry for each wash. If

this weight is exceeded, the washing results will be poor and the appliance may malfunction.

3. To save energy it is more economical to wash full loads of the various types of fabric, following the

guidance on quantities provided in the "Programmes Table" supplied in this manual.

4. Close the door by pressing against the frame until you hear it click shut. Take care not to trap items of

laundry between the door and the rubber gasket.

Warning!

 If the door is not properly closed, a safety device prevents the washer-dryer from starting.

 Do not exceed the maximum load: overloading adversely affects washing results.

4.5 ADDING DETERGENT AND ADDITIVE

The internal tray comprises three compartments, marked with the symbols

prewash detergent

main wash detergent

for fabric conditioner, starch, additives, etc. (e.g. treatment products). The additives are added to

the washing tank automatically during the final rinse.

The main wash detergent compartment has a tang allowing the use of liquid detergent. To insert it, pull it towards

the front and then lower it.

Following the recommendations in the "Programmes Table"

supplied with this manual, place the detergent and any addi-

tives in the drawer before the start of the programme.

Never fill with liquids above the maximum level marked; otherwise

the trays will empty too quickly.

Before pouring dense additives into the container, dilute with a little

water to ensure they do not clog the outlet.

Use only low-foam detergents suitable for use in a washer-dryer.

The amount of detergent must be decided in relation of the hard-

ness of the water, the type and quantity of items loaded, and their

degree of dirt.

This will provide the desired effect with optimal detergent consumption.

On detergent packs the recommended dose is indicated for 4 levels of water hardness and for loads of 4-5 kg of

laundry with average dirt levels.

Request information about the water's hardness from your water supply company.

Water hardness

Level of hardness French degrees fH German degrees dH

Soft Up to 15° Up to 8°

Medium 15° - 25° 8° - 14°

Hard 25° - 40° 14° - 22°

Very hard More than 40° More than 22°

EN

1

5

4.6 POWDER DETERGENT DOSES

Laundry with normal dirt

1. Choose a programme without prewash.

2. Pour the total amount of detergent shown on the pack into the main wash compartment of the detergent

drawer.

Very dirty laundry

1. Choose a programme with prewash.

2. Place ¼ of the recommended amount of detergent in the prewash compartment of the detergent drawer and

¾ of the detergent in the wash compartment.

Warning!

 If no recommended doses are provided, for delicate items in synthetic fibre use from ½ to 2/3 of the recom-

mended dose for washing tough cotton fabrics.

 Only neutral detergents recommended for wool should be used on the wool programme.

 Use the doses recommended by the detergent producer.

4.7 LIQUID DETERGENT DOSES

1. Pour the dose required into the measuring cap supplied with the bottle of liquid detergent and place it in the

drum, or use the main wash compartment of the detergent drawer, fitting the insert provided.

2. The scale on the red insert is intended as an aid when deciding the dose of liquid detergent.

Warning!

 Liquid detergents can be used, at the doses recommended by the producer, only for the main wash, i.e. in

all programmes without prewash.

4.8 DESCALERS

Descalers can be added to the prewash and main wash compartments as recommended by their producers.

Place the detergent in the compartments first, followed by the descaler.

4.9 PROGRAMMES AND FUNCTIONS

For advice on selecting programmes in relation to the type of fabric, refer to the "Programmes Table", sup-

plied with this manual.

EN

1

6

4.10 SWITCHING ON THE APPLIANCE AND SELECTING THE WASHING PROGRAMME

To switch on the appliance and select the programme, proceed as follows:

1. Turn the programmes knob in either direction. This switches on the washer-dryer.

2. Select the washing programme. The time left to the end of the programme and the maximum recommended

weight for the selected programme alternate on the display. The symbols on the display light up to identify the

information shown.

3. The default spin speed and temperatures values are shown. The initial settings can be modified using the

button underneath the sequence of spin speeds and temperatures.

4. If spin speed is set, there will be no spin cycle and the appliance will stop with the tank full. If this

value is set the appliance does not perform the final spin and the washing programme ends with water in the

tank.

Time to end

Max recommended wei

g

h

t

Spin Speed selection

Washing Temperature selection

EN

1

7

4.11 SELECTING AND CONFIRMING OPTIONS

1. The Option Selection button can be used to select the following options in sequence (from the top down):

Prewash: adds a stage before the main wash, lasting about 20 minutes at a temperature of 35°C. Suitable

for loads of particularly dirty items.

Intensive: the max. temperature is changed to 60°C and the washing stage is extended to increase the

effectiveness of the enzymes in the detergents. Suitable for delicate but dirty items.

Easy iron: produces items which are less creased and easy to iron.

Water plus: Increases the amount of water used for washing and rinses.

In alternative Extra rinse: this option adds a rinse to the selected washing programme.

Flexi Time: reduces the duration of the cycle. The symbol is completely illuminated with the initial duration

of the selected programme. Once the option has been selected the cycle duration can be further reduced

to an intermediate setting and a minimum setting and then returned to the initial duration by repeated

pressing of the Set button

In alternative Rapid: reduces the duration of the washing cycle. Suitable for small amounts of laundry with

only light dirt.

Buzzer: sets whether or not the buzzer will sound at the end of the cycle. The appliance comes with the

buzzer function "on".

2. To confirm the selected option, simply press the Confirm options button and the LED of the option remains

on.

3. To delete an option selection, simply return to the option with the Selection button and press the Confirm

options button. To annul all the options previously selected in a single operation, simply hold down the

Confirm options button for 4 seconds.

4. The Buzzer option retains its "on" or "off" status for subsequent cycles. It is only automatically switched to

"off" if the Night Wash programme is chosen.

O

p

tion selection Confirm option

Options

Start Pause

EN

1

8

4.12 TIME TO END

1. The Time to End key can be pressed repeatedly to select the time after which the washing programme will

end. The time to end of cycle function calculates the initial duration of the washing/drying cycle, the settings

made (temperature, spin speed and options) which may shorten or lengthen the cycle's initial duration, and

the delay time the user wishes to add before the cycle starts.

2. After the time to end has been set, the symbol on the display remains on.

3. To annul the Time to End function, keep pressing the key repeatedly until the display shows 0.

4. The Start Pause symbol flashes on and off until the cycle starts. After the cycle starts, the symbol remains

constantly lit.

4.13 STARTING THE WASHING PROGRAMME

1. To start the washing programme after making your personal settings, press the Start Pause button.

2. Once the cycle has started, the display shows the time remaining before the end of the cycle and the Start

Pause symbol on the display is constantly on.

3. During performance of the washing/drying programme, the symbols which identify the various phases light

up:

Time to end button

Time to end symbol

Start Pause

Start pause symbol

Cycle phase symbols: Prewash, wash, rinses, final spin and dry.

EN

19

4.14 INTERRUPTING OR CHANGING THE WASHING PROGRAMME

The washing programme in progress can be interrupted at any moment:

1. press the “Start/Pause” button for about 3 seconds: the display shows the word PAUS (for 1 second)

alternating with the time remaining until the end of the cycle (for 1 second). The Start/Pause light flashes

on and off.

Programmes can also be interrupted by turning the programme/temperature setting knob while the cycle

is in progress.

2. To change the washing programme, simply turn the programme knob to select the new programme; there

is no need to set the appliance in pause status. The new cycle will be carried out completely, beginning

from the start. If the tank had already been filled with water during the previous cycle, the water intake

phase will be omitted from the new programme.

3. To restart the cycle, press the Start-Pause button again.

4.15 PROGRAMME END

Washing/drying programmes are completed automatically. The word END appears on the display and the "Time

remaining" light goes out.

1. Switch the appliance off by turning the programmes knob to OFF

2. Unload the laundry from the drum.

3. Leave the door ajar to allow the interior of the washer-dryer to dry out.

4. Turn off the water intake tap.

If during the initial spin speed setting stage, the "no spin" mode with stop with tank full (spin speed set as 0)

was selected, at the end of the washing programme the word STOP appears on the display, alternating with ----

(spin speed of 0) and the spin light is on.

To proceed with the pump-out and spin, press the spin selection button twice. The appliance restarts the cycle with

the pump-out and spin. To select the spin speed required, press the button until the chosen speed is displayed. To

pump out the water from the tank without performing the spin, press the spin selection button until the display

indicates speed of 0: the pump-out will be run without spin.

La page charge ...

Smeg LSIA147 Manuel utilisateur

Smeg LSIA147 Manuel utilisateur

dans d''autres langues

Autres documents