Balluff BIS C-830-4-011-A RFID Reader Manuel utilisateur

Taper
Manuel utilisateur
www.balluff.com 1deutsch / english / français
BIS C-830-4-011-A
RFID-Reader
LF-Aufsteckmodul BF-IDC02 /
LF Plug-on Module BF-IDC02 /
Module Enfichable LF BF-IDC02
Dieses Produkt wurde unter Beachtung der in den Ländern
USA und Kanada geltenden Richtlinien entwickelt und
gefertigt. Die Konformität wurde nachgewiesen.
This product was developed and manufactured under
observance of the guidelines applicable in the USA and
Canada. The conformity has been proven.
Ce produit a été développé et fabriqué conformément aux
directives applicables aux États-Unis et au Canada. La
conformité a été prouvée.
USA:
FCC ID: 2AGZY-BFIDC02
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
this device may not cause harmful interference
this device must accept any interference received,
including interference that may cause undesired
operation of the device
Changes or modifications not expressly approved by the
party responsible for compliance voids the user's authority
to operate this equipment.
Note: This equipment has been tested and found to
comply with the limits for a ClassB digital device, pursuant
to part15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV techni-
cian for help.
Canada:
IC: 20739-BFIDC02
This device complies with Industry Canada license-exempt
RSS standard(s).
Operation is subject to the following two conditions:
this device may not cause interference
this device must accept any interference, including
interference that may cause undesired operation of the
device
This radio transmitter 20739-BFIDC02 has been approved
by Innovation, Science and Economic Development
Canada to operate with the antenna types listed below.
Antenna types not included in this list are strictly prohibited
for use with this device.
BIS C-323-05/S4
BIS C-325-05/S4
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence.
L’exploitation est autorisée aux deux conditions suivantes:
l’appareil ne doit pas produire de brouillage
l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement
Cet émetteur radio 20739-BFIDC02 a été approuvé par
Innovation, Science et Développement économique
Canada pour fonctionner avec les types d'antennes listés
ci-dessous. Les types d'antennes ne figurant pas dans
cette liste ne peuvent être utilisés.
BIS C-323-05/S4
BIS C-325-05/S4
FCC- und IC-Konformität /FCC and IC conformity / Conformidad FCC y IC
Draft (2023-07-07 / KV1)
2deutsch / english / français
BIS C-830-4-011-A
RFID-Reader
LF-Aufsteckmodul BF-IDC02 /
LF Plug-on Module BF-IDC02 /
Module Enfichable LF BF-IDC02
CE- und UKCA-Konformität /CE and UKCA
conformity / Conformidad CE y UKCA
Dieses Produkt wurde unter Beachtung der geltenden
europäischen Richtlinien entwickelt und gefertigt.
Die CE- und UKCA-Konformität wurde nachgewiesen.
This product was developed and manufactured in
accordance with all applicable European Directives.
CE and UKCA conformity has been verified.
Ce produit a été développé et fabriqué conformément aux
directives européennes applicables.
La conformité CE et UKCA a été prouvée.
Technische Daten / Technical data /
Caractéristiques techniques
Betriebsspannung
3,3VDC / 5VDCOperating voltage
Tension d'emploi
Stromaufnahme
bei 3,3VDC / 5VDC
≤10mA / ≤200mA
Current draw
at 3,3VDC / 5VDC
Consommation de courant
à3,3VDC / 5VDC
Arbeitsfrequenz
70kHz / 455kHzWorking frequency
Fréquence de travail
Modulation
ASK
Modulation
Modulation
Antennentyp Extern, induktiv
Antenna type External, inductive
Type d’antenne Externe, inductif
Das RFID-System ist ausschließlich für die Verwendung
folgender passiver BISC-Antennen vorgesehen / The RFID
system is designed exclusively for use with the following
passive BISC antennas / Le système RFID est
exclusivement prévu pour l’utilisation des antennes
passives BISC suivantes:
BIS C-323-05/S4
BIS C-325-05/S4
Änderungen vorbehalten. / Subject to modification. / Sous
réserve de modifications.
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Germany
www.balluff.com/go/contact
956828_AB ∙ DE/EN/FR ∙ G23; Subject to modification. Replaces E23.
Draft (2023-07-07 / KV1)
  • Page 1 1
  • Page 2 2

Balluff BIS C-830-4-011-A RFID Reader Manuel utilisateur

Taper
Manuel utilisateur