WAC Lighting WS-63412 Mode d'emploi

Taper
Mode d'emploi
1
INSTALLATION INSTRUCTIONS
634 - LED Wall Sconce
WS-63412
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, nappuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus
pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
A
B
Wire Connector
Qty: 3PCS+1 Extra
Canopy screw
Qty: 1 Extra
Hardware
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the mounting plate.
4. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000K),
which can be adjusted to your preference with the switch mounted in the canopy. (Fig.3).
Note: the switch comes with removable protective cover, Remove the cover prior
to making adjustment, Reinstall the cover after adjustment is made.
5. Secure the ceiling plate to the junction box using the screws provided with the
junction box.
Note: (i)using any other non-original-manufacturer provided junction box screw may
result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES(Fig. 2, Fig. 3)
8. Connect the driver input wires to junction box as shown in Fig .2. Making sure that
all wire connectors (A) are secured. If your outlet box has a green or bare copper
ground wire, connect the xture’s ground wire to it. Otherwise, connect the
xture’s ground wire directly to the back plate using the GND screwprovided.
After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
12. Secure the canopy to the ceiling plate use the canopy screw (C).
2
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
INSTALLATION INSTRUCTIONS
634 - LED Wall Sconce
WS-63412
1 3/4"
1 3/8"
Ø4 5/8”
Mounting Plate Dimensions
Fig.3 Driver Wires
White - Neutral
Black - Hot
Input
Output
Driver
Canopy
Brown C
Black W
Brown C
Blue W
Black -
Black -
Red +
Red +
FIG. 1
Wire Connector
A
B
Mounting Plate
Mounting Screw
Junction Box Screw
Junction Box
Fixture
Driver
4CCT Switch
4CCT Switch Cap
Ground Wire
Fig. 2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Live)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
  • Page 1 1
  • Page 2 2

WAC Lighting WS-63412 Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues