Horizon Hobby HBZ5305 Manuel utilisateur

HBZ5305
Horizon Hobby
Marque
Horizon Hobby
Modèle
HBZ5305
Taper
Manuel utilisateur
1.HBZ5305Receiver/ESC:Duet
1.1.1.Introduction
Horizon Hobby would like to announce a low-cost flight controller module
which contains a 2.4GHz RF receiver, a gyroscope, motor output electronics,
servos, and the control chips. The highly integrated module makes the
possibilities of LVC telemetry. The module is specifically developed for all
non-spektrum airplanes.
1.2.2.Features
1.2.1. Support 2.4GHz Zigbee network
1.2.2. 2.4Ghz supports 16 channels
1.2.3. Support on UART output.
1.2.4. Support three pwm outputs.
1.2.5. Support two main motors outputs.
1.2.6. Stabilization control with 6-axis gyro
1.3.3.GeneralSpecificaiton
1.3.1.ModelName
1.3.1.1.HBZ5305 Receiver/ESC: Duet
1.3.2.ProductDescription
1.3.2.1.HBZ5303 is a low-cost mian control modlue used in a wireless remote control
fixed-wing model plane, which contains a 2.4GHz RF receiver module for flight control, a
gyroscope, motor, servos, and the control chips. Its center frequency is 2405~2475MHz.
1.3.3.Dimension:
1.3.3.1.LxWxH: 34.5x27.5x8.9mm
HBZ5305Receiver/ESC:Duet
1.3.4.2.4GHzInterface
1.3.4.1.SPI
1.3.5.Operatingtemperature
1.3.5.1.-10°C to 55°C
1.3.6.Storagetemperature
1.3.6.1.-30°C to 85°C
1.3.7.VDD
1.3.7.1.DC:3.0V-4.2V
1.3.8.SW
1.3.8.1.V01
1.3.9.HW
1.3.9.1.V0
1.4.4.2.4GHzRFSpecification
1.4.1. RF Output Power
1.4.2. Power Spectral Density
1.4.3. Occupied Channel Bandwidth
1.4.4. Transmitter Unwanted Emissions in the Out-of-band Domain
1.4.5. Transmitter Unwanted Emissions in the Spurious Domain
1.4.6. Receiver Spurious Emissions
1.4.7. Receiver Blocking
1.5.5.PinAssignment
1.5.1.PinOutline
1.5.1.1.
1.5.2.PinDefinition
1.5.2.1.1 2 3 Servo port
1.5.2.2.4 5 Motor port
1.5.2.3.6 OTA upgrade port
1.5.2.4.7 LED port
1.5.2.5.8 9 Onboard Servo
1.5.2.6.10 Power cable
1.5.2.7.11 Antenna
1.5.2.8.12 13 Onboard servo cable
1.6.6.Dimensions
1.6.1.PhysicalOutline Unit:mm
1.6.1.1.
1.6.1.2.
1.7.7.FuntionalBlockDiagram
1.8.8.RecommendedReflowProfile
1.9.MPEWarning
1.9.1.FCC
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the part responsible for
compliance could void the user's authority to operate this equipment.
This module has been tested and found to comply with Part 15C requirements for Modular
Approval.
The module is tested for standalone mobile RF exposure use condition.
(1) The antenna must be installed such that 20 cm is maintained between the antenna and
users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. .
The module is a limited modular, tested in a specific host (Model: HBZ05300; Brand:
HobbyZone). If other hosts are used, the OEM integrator will be responsible for re-
evaluating the end product.
The following antennas have been certified for use with this module.
Only antennas of the same type with equal or lower gain may also be used with this
module.
Other types of antennas and/or higher gain antennas may require the additional
authorization for operation. Antenna Specification list below:
--Antenna Type: Monopole Antenna
--Frequency Bands (MHz): 2405 ~ 2475
--Antenna Gain (dBi): 2.11
When the module is installed in the host device, the FCC ID label must be visible through a
window on the final device or it must be visible when an access panel, door or cover is
easily re-moved. If not, a second label must be placed on the outside of the final device
that contains the following text: Contains FCC ID: BRWHBZ5303 . The FCC ID can be
used only when all FCC compliance requirements are met.
This transmitter is tested in a standalone mobile RF exposure condition in the specific
host. And any co-located or simultaneous transmission with other transmitter(s) may
require a Class II permissive change re-evaluation or a new grant.
This module transmitter is only authorized for the specific rule parts listed on the grant.
And the host product manufacturer/OEM is responsible for compliance to any other FCC
rules that apply to the host not covered by the modular transmitter grant of certification.
The modular doesn t comply with the requirements of Part 15 Subpart B. The host must
comply with the requirements of Part 15 Subpart B.
1.9.2.ISED
This device complies with Industry Canada license-exempt RSSs. Operation is subject to
the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d Industrie Canada applicables aux appareils
radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes:
1. l appareil ne doit pas produire de brouillage;
2. l utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d en compromettre le fonctionnement.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Cet équipement est conforme aux limites d exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
The transmitter module may not be co-located with any other transmitter or antenna. The
OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
1) Operation shall be limited to indoor use only; and
2) This device is limited to under control an indoor access point or an indoor
The module is tested for standalone mobile RF exposure use condition.
(1) The antenna must be installed such that 20 cm is maintained between the antenna and
users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
In the event that these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the ISED authorization is no longer
considered valid and the IC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate ISED authorization.
The module is a limited modular, tested in a specific host (Model: HBZ05300; Brand:
HobbyZone). If other hosts are used, the OEM integrator will be responsible for re-
evaluating the end product.
Le module est testé pour les conditions d'utilisation de l'exposition aux radiofréquences
des téléphones mobiles autonomes.
(1) L'antenne doit être installée de manière à ce que 20 cm soient maintenus entre
l'antenne et les utilisateurs,
(2) Le module d'émission ne peut pas être installé en même temps qu'un autre émetteur
ou qu'une autre antenne.
Si ces conditions ne peuvent pas être remplies (par exemple, certaines configurations
d'ordinateurs portables ou la co-implantation avec un autre émetteur), l'autorisation ISED
n'est plus considérée comme valide et l'IC ID ne peut pas être utilisé sur le produit final.
Dans ce cas, l'intégrateur OEM devra réévaluer le produit final (y compris l'émetteur) et
obtenir une autorisation ISED distincte.
Le module est un module limité, testé dans un hôte spécifique (modèle : HBZ05300 ;
marque : HobbyZone). Si d'autres hôtes sont utilisés, l'intégrateur OEM sera responsable
de la réévaluation du produit final.
1.10.9.PackageInformaion:30pcsinonetray
1.10.1.
1.10.2.
1.10.3.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Horizon Hobby HBZ5305 Manuel utilisateur

HBZ5305
Horizon Hobby
Marque
Horizon Hobby
Modèle
HBZ5305
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents