Modern Forms WS-80827 Vigo Mode d'emploi
- Taper
- Mode d'emploi
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements
locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDEs
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et
ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire Connector
Qty: 3pcs+1 Extra
7EAC112201
A
Screw
Qty: 2pcs+1 Extra
7MPF0405C1
5/32”-32”X3/16
Polished Nickel
D
Mounting Screw
Qty: 1 Extra
7MPF0412S1
5/32”-32X1/2
Polished Nickel
C
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0415C2
#8-32x9/16
SS
Washer
Qty: 2pcs+1 Extra
7MPH0804A1
Wood Screw
Qty: 2pcs+1 Extra
7MPF2204J2
Ø4x7/8
Nickel Plating
Washer
Qty: 2pcs+1 Extra
7MPH0804A1
B E F G
G0
INSTALLATION INSTRUCTION
808 – LED Wall Sconce
WS-80827/ WS-80838/WS-80827F/ WS-80838F
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (C) from the mounting back plate.
4. Secure the mounting back plate to the junction box using junction box screws (B). The side of the mounting back plate marked “GND” must
face out.
5. Insert the glass into the lamp body vertically and carefully, and secure them with screws (D)and washer (E).
CONNECTING THE WIRES (Fig. 2)
6. Connect the xture’s wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 3)
7. Secure the xture to the mounting back plate using the mounting screw (C).
INSTALLATION INSTRUCTION
808 – LED Wall Sconce
WS-80827/ WS-80838/WS-80827F/ WS-80838F
G0
Fig.1 Mount on Switch Box
Mounting Backplate
#7MBC501003
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Lamp Body
Mounting Screw Wood
Screw
Mounting
Backplate
Plastic
Anchor Wire Connector
Junction Box
Ground Wire
Junction
Box Screw
Screw
Washer
Mitered Glass
(WS-80827:RPL-GLA-80827)
(WS-80838:RPL-GLA-80838)
C
F
GA
B
D
E
41
4″
13
8″
13
4″
235
8″
311
2″
WS-80827:195
8″
WS-80838:
WS80827:153
4″
WS80838:
WS-80827
WS-80827
WS-80838
WS-80838
19 5/8”
4 1/4”
15 3/4”
1 3/4” 1 3/8”
31 1/2”
23 5/8”
-
1
-
2
Modern Forms WS-80827 Vigo Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-42832 Mulholland Mode d'emploi
-
-
-
-
-
-
-
-
-
