Good Earth Lighting SE1037-TBZ-00LF0 Mode d'emploi

Marque: Good Earth Lighting

Modèle: SE1037-TBZ-00LF0

Taper: Mode d'emploi

- 1 - - 3 -

- 2 - - 4 -

WARNING: Please read this entire manual before installation.

Verify the following contents:

AVERTISSEMENT : Veuillez lire ce mode d'emploi du début à la fin avant

de commencer l'installation. Vérifiez le contenu suivant :

ADVERTENCIA: Por favor, lea este manual completo antes de realizar la

instalación. Verifique el siguiente contenido:

Model/Modèle/Modelo #:

SE1037-TBZ-00LF0-E

SWITCH CONTROLLED LED SECURITY LIGHT (Page 1)

ÉCLAIRAGE DE SÉCURITÉ À DEL COMMANDÉ

PAR INTERRUPTEUR

(Page 4)

LUZ LED DE SEGURIDAD CONTROLADA

POR INTERRUPTOR

(Página 8)

To Begin/Pour commencer/Para comenzar

Required/Nécessaire/Se necesita

Safety glasses

Lunettes de sécurité

Gafas de seguridad

Flathead screwdriver

Tournevis à tête plate

Destornillador de cabeza plana

Phillips screwdriver

Tournevis cruciforme

Destornillador Phillips

Installation time: 45 minutes

Temps d’installation : 45 minutes

Tiempo de instalación: 45 minutos

Drill bits 1/16 in.

Forets de 1/16 po

Brocas para taladro de 1/16 pulg

Electrical tape

Ruban isolant

Cinta aislante

Drill

Perceuse

Taladro

Pliers

Pinces

Pinzas

Wire cutters

Coupe-fil

Pinzas cortacables

Wire strippers

Pinces à dénuder

Pinzas pelacables

Silicone

Silicona

GND

FRONT

Hardware kit (Actual hardware may differ from illustration).

Trousse de quincaillerie (La quincaillerie incluse peut être différente de l’illustration.)

Kit de aditamentos (Los aditamentos reales pueden diferir de los que se muestran en la ilustración.)

Wall plate

Plaque murale

Pared plana

LED head

Tête du LED

Cabezal del LED

Diffuser

Diffuseur

Difusor

English

Warnings and Cautions

WARNING

• Shut off power at the circuit breaker or fuse panel before removing the

old fixture or installing the new one.

• LEDs can be damaged by electrostatic discharge (ESD) shock. Before

installation, discharge yourself by touching a grounded bare metal

surface to remove this hazard. To avoid damage, do not remove the

clear lens over the LED module.

CAUTION

• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If dimmer

controls are present, remove them and replace them with regular

electrical switches. If a three-way dimmer is present, replace it with a

regular three-way switch. If unfamiliar with electrical installations, it is

recommended a qualified electrician do the installation.

• This device complies with Part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

IMPORTANT: This light fixture uses light emitting diodes (LEDs) to provide

light. LEDs do not have a filament to burn out like a traditional light bulb.

LEDs gradually emit less light over their lifetime, but will typically last 50,000

hours in a residential environment.

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner

and soft cloth. When cleaning the fixture, make sure the power is turned off.

Do not spray cleaner directly onto any part of the fixture or LEDs.

Care and Maintenance

Minor problems often can be fixed without the help of an electrician. Before doing any work

on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

noituloS esuaC melborP

Fixture doesn’t light. Power is off. Check if power supply is on.

Bad connection. Check cords and/or wiring.

Bad switch. Test or replace switch.

Fuse blows or circuit breaker Discontinue use. Call customer service.

trips when light is turned on.

Troubleshooting Guide

Disconnect power to the electrical box and remove the old fixture. If more than two

wire leads are present, keep track of which wires were connected together.

Installation For Round Surface Mount Electrical Boxes

Pull the supply wires out of the electrical box. Using the

machine screws that fit the electrical box, secure the

mounting strap to the electrical box, making sure that

the side marked “FRONT” is facing out (Fig. 1).

Fig. 1

Remove the protective paper barrier from the adhesive

face of the foam gasket. Trace the supply wires through

the openings in the gasket and adhere the gasket to the

mounting strap and outer edge of the round surface

mount electrical box (Fig. 2).

Position the wall plate over the mounting strap so the

center hole of the wall plate aligns with the center hole

in the mounting strap. While holding the wall plate in

place, put the long machine screw through the center

hole of the wall plate and mounting strap. Tighten the

screw properly to secure the wall plate onto the

electrical box (Fig. 5). NOTE: Make sure the gasket

properly seals the gap between the wall plate and the electrical box to prevent water

seepage into the electrical box.

Fig. 2

GND

FRONT

GND

FRONT

Fig. 5

This fixture can be eave mounted (Fig. 6).

If the light head is loose and will not hold its position

tighten the screws located on the backside of the light

head that surround the pivot joint (Fig. 4). NOTE: Tighten

the screws before securing the fixture to the electrical

box.

Fig. 4

Important Safety Instructions

WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS:

1. Do NOT touch LEDs.

2. Do NOT remove the protective clear LED lens.

3. Do NOT look directly at lighted LEDs for any length of time.

4. Do NOT touch, operate, or install fixture while in contact with water.

5. For electrical requirements, see back of the fixture. Minimum 90° supply

conductors.

6. Do not leave bare wires exposed outside the wall canopy enclosure.

7. Suitable for installation onto round surface mount electrical boxes or

recessed electrical boxes rated for wet locations. Fixture can be wall or

eave mounted. NOT suitable for ground mount installations.

8. Do NOT mount below 5 ft.

SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE FIXTURE TO

REFER TO THEM AT A LATER TIME.

Fig. 4

Disconnect power to the electrical box and remove the old fixture. If more than two

wire leads are present, keep track of which wires were connected together.

Pull the supply wires out of the electrical box. Using the

machine screws that fit the electrical box, secure the

mounting strap to the electrical box, making sure that

the side marked “FRONT” is facing out (Fig. 1).

Fig. 1

Position the wall plate over the mounting strap so

the center hole of the wall plate aligns with the center

hole in the mounting strap. While holding the wall plate

place the long machine screw through the center

hole of the wall plate and mounting strap. Tighten

the screw properly to secure the wall plate onto the

mounting surface (Fig. 4).

Restore power to the electrical box at the circuit

breaker or fuse panel. Make sure the wall switch that

controls the electrical box for your security light is

returned to the “ON” position and check that your light

is functioning properly. If the light is functioning

properly, use silicone adhesive caulking (not included)

to caulk the gap between the wall plate and the

mounting surface to prevent water seepage into the electrical enclosure (Fig. 6).

Fit the silicone cap into the mounting screw

opening to prevent water seepage into the

housing (Fig. 7).

Fig. 7

Fig. 6

Installation For Recessed Electrical Boxes

This fixture can be eave mounted (Fig. 5).

Fig. 6

Fig. 5

If the light head is loose and will not hold its position

tighten the screws located on the backside of the light

head that surround the pivot joint (Fig. 3). NOTE: Tighten

the screws before securing the fixture to the electrical

3box.

Fig. 3

Restore power to the electrical box at the circuit

breaker or fuse panel. Make sure the wall switch that

controls the electrical box for your security light is

returned to the “ON”position and check that your light is

functioning properly. If the light is functioning properly,

fit the silicone cap into the mounting screw opening to

prevent water seepage into the housing (Fig. 7).

Fig. 7

Keep this guide handy for

ordering replacement parts.

Hardware Kit

ZH-SE1037F00-TBZ

In the event you are missing a part or have questions regarding installation

please visit our website at www.goodearthlighting.com/support or

call the Customer Care Center 1-800-291-8838,

8:30 a.m.-5 p.m., CST, Monday-Friday.

Need Help?

Replacement Parts List

6 YEAR LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of (6) years from the date of original purchase by the consumer.

The fixture is not warrantied for use in a commercial or retail application. The warranty is

limited to use in a residential environment. We will repair or replace (at our option) the

unit in the original color, and style if available, or in a similar color and style if the original

item has been discontinued, without charge. Defective units must be properly packed and

returned to the manufacturer with a letter of explanation and your original purchase

receipt showing date of purchase. Call 1-800-291-8838 to obtain a Return Authorization

Number and an address where to ship your defective product. Note: C.O.D. shipments will

NOT be accepted. The liability of the manufacturer is in any case limited to replacement

of the defective light fixture product. The manufacturer will not be liable for any other

loss, damage, labor costs or injury which is caused by the product. This limitation upon

the liability of the manufacturer includes any loss, damage, or injury which is (I) to person

or property or otherwise; (II) incidental or consequential in nature; (III) based upon

theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV)

directly, or indirectly related to the sale, use, or repair of the product. This warranty gives

you specific rights, and you may also have other rights which vary from state to state.

Printed in ChinaEcolight® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056

Warranty

For safety and proper installation, the fixture must be

properly grounded. If unfamiliar with the methods of

properly grounding the fixture, consult with a qualified

electrician. A green copper ground wire is

pre-attached to the fixture. If the electrical box is made

of plastic and/or has a green or bare copper grounding

wire inside, the fixture grounding wire and the

electrical box ground wire should be connected together using the wire nut. If the

electrical box is made of metal and already grounded, secure the bare end of the

fixture ground wire to the mounting strap marked “GND” using the green grounding

screw. Push-in connectors are pre-installed onto the fixture’s wire leads to allow for

easy connection. Insert the black lead from the electrical box into the black wire

push-in connector

(Fig. 3)

. Repeat with the white leads. Push the excess wires back

into the electrical box.

For safety and proper installation, the fixture must be

properly grounded. If unfamiliar with the methods of

properly grounding the fixture, consult with a qualified

electrician. A green copper ground wire is

pre-attached to the fixture. If the electrical box is made

of plastic and/or has a green or bare copper grounding

wire inside, the fixture grounding wire and the

electrical box ground wire should be connected together using the wire nut. If the

electrical box is made of metal and already grounded, secure the bare end of the

fixture ground wire to the mounting strap marked “GND” using the green grounding

screw. Push-in connectors are pre-installed onto the fixture’s wire leads to allow for

easy connection. Insert the black lead from the electrical box into the black wire

push-in connector

(Fig. 2)

. Repeat with the white leads. Push the excess wires back

into the electrical box.

Fig. 2

Fig. 3