Simplicity 076109 Manuel utilisateur

1

Operator’s Manual

Liquid-Cooled

Generator System

Standby Generator Systems

This generator is certied in accordance with

UL (Underwriters Laboratories) 2200 (stationary

engine generator assemblies) and CSA (Canadian

Standards Association) standard C22.2 No. 100-04

(motors and generators).

80005276 Rev. C

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® generator. We’re pleased that you’ve placed your confidence in

the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby generators and

how to avoid them. Because we do not necessarily know all the applications this equipment could be used for, it is important

that you read and understand these instructions thoroughly before attempting to start or operate this equipment. This product

is only for use as an optional generator system which provides an alternate source of electric power and to serve loads such

as heating, refrigeration systems, and communication systems that, when stopped during any power outage, could cause

discomfort or inconvenience.

Save these original instructions for future reference.

This generator requires professional installation before use. Refer to the separate installation manual for full information.

Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages. There

are thousands of Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Technical Service by phone at 800-732-2989, or click on Find a Dealer at BRIGGSandSTRATTON.COM, which provides a list of

authorized dealers.

Generator and engine model and serial numbers should be recorded in the installation manual.

Briggs & Stratton Power Products Group, LLC

P.O. Box 702

Milwaukee, WI 53201-0702

may be reproduced or transmitted in any form without the express

written permission of Briggs & Stratton Power Products Group, LLC.

3

Table of Contents

Important Safety Instructions........................4

Installation ....................................7

For the Standby Owner: ........................................7

For the Installing Dealer/Contractor: ..............................7

Owner Orientation ............................................7

Fuel Factors .................................................8

Generator Location............................................8

Delivery Inspection............................................9

Controls ..................................... 10

Access Ports ...............................................11

System Control Panel.........................................13

General Set Up Screen........................................15

Control Panel Prompts........................................16

Operation .................................... 17

Important Owner’s Considerations...............................17

Engine Oil..................................................17

Battery ....................................................17

15 Amp Fuse ...............................................17

Automatic Operation Sequence .................................17

Setting Exercise Timer ........................................18

Maintenance .................................. 18

Servicing the System .........................................18

Service Code Detection System .................................18

Generator Maintenance .......................... 20

Engine Maintenance..........................................21

Changing Engine Oil and Oil Filter ...............................21

Engine Drive Belt ............................................22

Engine Air Cleaner ...........................................22

Generator Electrical System Maintenance .........................23

Battery ....................................................23

Fuel System Inspection and Maintenance .........................24

Exhaust System Maintenance and Inspection ......................24

When Calling for Assistance ...................................25

Storage....................................................25

Maintenance Chart ...........................................26

Troubleshooting................................ 27

Generator Specifications.......................... 28

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the generator system unsafe.

Fire

Toxic Fumes

Explosive Pressure

Rotating Fan Blade

Lift Hazard

Read Manual

Rotating Belt/Pulley

Chemical BurnAuto Start

Hot SurfaceRotating Parts

Electrical Shock

Explosion

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will

not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open garage

doors or other openings that can allow exhaust gas

to enter inside or be drawn into a potentially occupied

building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

WARNING Storage batteries give off explosive hydrogen

gas during recharging.Slightest

spark will ignite hydrogen and

cause explosion, resulting in death

or serious injury. Battery electrolyte fluid contains acid and is

extremely caustic.Contact with battery contents could cause

severe chemical burns.A battery presents a risk of electrical

shock and high short circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

Save These Instructions

5

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

inelectrocution.

Failure to isolate generator from utility power

could result in death or serious injury to electric utility

workers due to backfeed of electrical energy.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or feet

are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk of a

shock hazard.

• DO NOT allow unqualified persons or children to operate

or service generator.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical power and

contact the local authorities. Avoid direct contact with

the victim.

• Despite the safe design of the generator, operating this

equipment imprudently, neglecting its maintenance or

being careless could cause possible injury or death.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• Before performing any maintenance on the generator,

disconnect the battery cable indicated by a NEGATIVE,

NEG or (-) first. When finished, reconnect that cable last.

• After your system is installed, the generator may crank

and start without warning any time there is a power

failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING Hazardous Voltage - Contact with power

lines could cause electric shock or

burns, resulting in death or serious

injury. Lifting Hazard / Heavy Object -

Could result in serious injury.

• If lifting or hoisting equipment is used, DO NOT contact

any power lines.

• DO NOT lift or move generator without assistance.

• DO NOT lift unit by roof as damage to generator

will occur.

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could

cause burns, fire or explosion resulting

in death or serious injury.

• Install the fuel supply system according to NFPA 37 and

other applicable fuel-gas codes.

• Before placing the generator into service, the fuel system

lines must be properly purged and leak tested.

• After the generator is installed, you should inspect the fuel

system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or other

explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any oil

spills immediately. Ensure that no combustible materials

are left in the generator compartment. Keep the area near

the generator clean and free of debris.

WARNING Exhaust heat/gases could ignite

combustibles or structures resulting in

death or serious injury.

Contact with muffler area could cause

burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5m) from windows, doors, any wall opening,

shrubs or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a

minimum of 5 ft. (1.5 m) overhead clearance from any

structure, overhang, or trees.

• DO NOT place weatherproof enclosure under a deck or

other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect provided fuel

line to generator. DO NOT use with or substitute any other

flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator cooling

and maintenance clearances.

• Replacement parts must be the same and installed in the

same position as the original parts.

6 BRIGGSandSTRATTON.COM

WARNING Moving parts could crush and cut.

Starter and

other rotating parts could entangle

hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate generator without protective housings,

covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel

and disconnect Negative (NEG or -) battery cable.

WARNING Hot pressurized coolant could cause

serious injury.

• DO NOT open radiator cap when hot.

• Before servicing, allow coolant to cool.

CAUTION Installing the 15A fuse could cause the

engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed from the

control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has

been completed and inspected.

CAUTION Excessively high operating speeds could

result in minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at

governed speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could damage

it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation.

• The access panels/door must be installed whenever the

unit is running.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step.

Stepping on the unit could cause stress and break parts.

This may result in dangerous operating conditions from

leaking exhaust gases, fuel leakage, oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

-unit makes unusual noises.

7

Installation

We sincerely appreciate your patronage. For this reason, we

have made every effort to provide for a safe, streamlined

and cost-effective installation. Because each installation is

unique, it is impossible to know of and advise the trade of all

conceivable procedures and methods by which installation

might be achieved. Neither could we know of possible

hazards and/or the results of each method or procedure.

For these reasons, only current licensed electrical and

plumbing professionals should attempt standby generator

system installations. Installations must strictly comply with all

applicable codes, industry standards, laws and regulations.

Your standby generator is supplied with this “Operator’s

Manual” and a separate “Installation and Start-Up Manual.”

These are important documents and should be retained by

the owner after the installation has been completed.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

This product is only for use as an optional generator system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system as

defined by NFPA 70 (NEC).

• Emergency generator systems are intended to automatically

supply illumination, power, or both, to designated areas

and equipment in the event of failure of the normal supply.

Emergency systems may also provide power for such

functions as ventilation where essential to maintain life,

where current interruption of the normal supply would

produce serious life safety or health hazards.

• Legally Required standby generator systems are intended

to automatically supply power to selected loads in the

event of failure of the normal source which could create

hazards or hamper rescue or fire-fighting operations.

For the Standby Owner:

To help you make informed choices and communicate

effectively with your installation contractor(s), read and

understand Owner Orientation in this manual before

contracting or starting your generator installation.

To arrange for proper installation, contact the store at which

you purchased your generator, your dealer, a licensed

electrician or your utility power provider.

The generator warranty is VOID unless the system is

installed by licensed electrical and plumbing professionals.

The Emission Control System for this generator is warranted

for standards set by the U.S. Environmental Protection

Agency and by the California Air Resources Board (CARB).

For the Installing Dealer/Contractor:

For most applications, the installation manual contains all

the information required to properly install and start the

generator. This operator’s manual describes routine operation

and owner maintenanceprocedures.

If you need more information in this matter, please call at

800-732-2989 between 8:00 AM and 5:00 PM CT.

Owner Orientation

This section provides generator owners with the information

necessary to achieve the most satisfactory and cost effective

installation possible.

The illustrations are for typical circumstances and are meant

to familiarize you with the installation options available

with your generator. A thorough understanding of these

options will provide fundamental control over the cost of

your installation, as well as ensure your final satisfaction

and security.

Federal and local codes, appearance, noise levels, fuel types,

and distances are the factors that must be considered when

negotiating with an installation professional. Remember

that as the distance from the existing electrical service and

gaseous fuel supply increases, and the number of 90 degree

bends in the fuel supply increases, compensations in piping

and wiring materials must be made. This is necessary to

comply with local codes and overcome electrical voltage

drops and gaseous fuel pressure drops.

The factors mentioned above will have a direct affect on

the overall price of your generator installation.

In some areas you may need to acquire electrical permits for

installing the generator, building permits for installing gas lines,

and permits for noise allowances. Your installer should check your

local codes AND obtain the permits before installing the system.

8 BRIGGSandSTRATTON.COM

Fuel Factors

An important consideration affecting the entire installation

is the type of fuel used by your generator. The system was

factory tested and adjusted using either natural gas or liquid

propane (LP vapor). For proper engine function, factors

that are inherent to each of these fuels, your location and

the duration of possible utility interruptions are important

considerations in the following fuel guidelines:

• Use clean, dry fuel, free of moisture or any

particulate material. Using fuels outside the following

recommended values may cause performanceproblems.

• In engines set up to run on propane (LP), commercial

grade HD5 propane with a minimum fuel energy of 2500

BTUs/ft3 with maximum propylene content of 5% and

butane and heavier gas content of 2.5% and minimum

propane content of 90%.

Power Decrease at High Altitude or High Temperature

Air density is less at high altitudes, resulting in less available

engine power. Specifically, engine power will decrease 3% for

each 1,000 feet (300 meters) above sea level and 1% for each

10°F (5.6°C) above 77°F (25°C). Make sure you and your installer

consider these factors when determining total generator load.

WARNING

Propane and Natural Gas are extremely

flammable and explosive, which could

cause burns, fire or explosion resulting

in death or serious injury.

• The generator is equipped with an automatic safety gas

“fuel shut-off” valve.

• DO NOT operate the equipment if the “fuel shut-off” valve

is missing or inoperative.

Generator Location

The actual physical location of your generator has a direct

affect on:

1. The amount of plumbing required to fuel your generator.

2. The amount of wiring required to control and connect

your generator.

Specific location guidelines are discussed in the installation

manual. Acquaint yourself with that information and confer

with your installer. Be sure to ask how your site might

affect installation costs and compliance with local codes

andstandards.

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

• By law it is required in many states to have a Carbon

Monoxide (CO) detector in operating condition in

your home. Carbon monoxide detector(s) (A) MUST

be installed and maintained indoors according to the

manufacturer’s instructions/recommendations. A CO

monitor is an electronic device that detects hazardous

levels of CO. When there is a buildup of CO, the monitor

will alert the occupants by flashing visual indicator light

and alarm. Smoke alarms cannot detect CO gas.

A

9

WARNING Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will

not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open garage

doors or other openings that can allow exhaust gas

to enter inside or be drawn into a potentially occupied

building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

WARNING Exhaust heat/gases could ignite combustibles

or structures resulting in death or serious injury.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5 m) minimum clearance from any

structure, shrubs, trees, or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall opening,

shrubs or vegetation over 12 in. (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a

minimum of 5 ft. (1.5 m) overhead clearance from any

structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck or

other type of structure that may confine airflow.

• USE ONLY flexible fuel line provided. Connect provided

fuel line to generator. DO NOT use with or substitute any

other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• DO NOT place weatherproof enclosure in manner other

than shown in illustrations.

• Ensure exhaust gas is kept away from any windows,

doors, ventilation intakes, soffit vents, crawl spaces,

open garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a potentially

occupied building or structure. Neighboring structures

may be exposed to the engine exhaust from your standby

generator and must be considered when installing your

standby generator.

• Wind and air currents should be taken into consideration

when positioning generator.

See the Installation Manual for full details on safe generator

location.

Delivery Inspection

Carefully inspect the generator for any damage that may have

occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss

or damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier and your

installer for claim procedures. Missing or damaged parts are

not warranted.

The standby generator system is supplied with:

• Fully-serviced coolant system

• Fully-serviced oil/lubricating system

• Synthetic oil (5W30)

• Flexible fuel line

• Installation and start-up manual

• Operator’s manual

• Spare access roof and door keys

• Spare 15 Amp ATO-type fuse

• Coolant

• Touch-up paint

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Reinforced concrete pad

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables, spreader bar

• Two 60” lengths of 2” Schedule 40 pipe (NOT conduit)

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

• Various special tools and equipment

10 BRIGGSandSTRATTON.COM

Controls

25 kW Generator

Read this operator’s manual and Important Safety Instructions before operating your generator.

Compare the illustrations of this model with your generator to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

Generator is pictured with access doors removed and internal

guard open for clarity.

A. Exhaust Port — High-performance muffler lowers

engine noise to comply with most codes.

B. Engine Label — Identifies engine model and type.

C. Oil Dip Stick — Used to check the engine oil level.

D. Roof Access Opening — Provides access to control

panel, oil filter, etc.

E. Circuit Breaker Enclosure — Equipped with removable

top to assist with conduit connection.

F. Control Panel — Used for various test, operation and

maintenance functions. See System Control Panel.

G. Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

H. Fuel Selection Switch — Select natural gas or liquid

propane (LP vapor) supply.

J. Oil Fill Cap — Remove to service the engine with

recommended oil.

K. Coolant Fill — Provides access for filling engine

coolant.

L. Coolant Recovery Bottle — Provides visual indicator of

engine coolant level.

M. Fuel Inlet — Fuel supply is connected here.

N. ID Label — Identifies unit by serial number.

P. Rear Access Panel Opening — Provides access to

various components of generator.

R. Oil Filter — Filters engine oil to prolong system life.

S. Front Access Panel Opening — Provides access to

various components of generator.

T. Battery Location — Battery located for convenient

access.

A

B

C

D E

F

G

T

S

R

L

K

J

N

M

P

H

11

Access Ports

The generator is equipped with an enclosure that has several

access panels, as shown.

The access panels and the components located behind them

are listed below:

A - Roof (Control Panel, internal guard)

B - Front Access Panel (oil drain and oil filter)

C - Internal Guard (air filter, oil dipstick, coolant bottle)

D - Rear Access Panel (fuel regulator, fuel selector, and

engine starter)

E - Control Panel Cover (field wiring and control wires)

Each generator is shipped with a set of identical keys. These

keys fit in the lock on the front and rear removable panels.

The roof must be unlocked in order for it to open.

To open roof:

1. Insert key into lock (F) of front panel. Gently push

down on roof above the lock to aid in turning the key.

Turn key one quarter turn clockwise.

2. Lift roof to the open position.

To close roof:

1. Carefully lower roof down onto the unit.

2. Once lowered, insert key and turn counterclockwise to

secure roof.

3. Remove key from unit.

D

A

E

B

C

F

12 BRIGGSandSTRATTON.COM

To open internal guard:

1. Ensure the roof is in the open position.

2. Remove the two bolts (G) that secure the internal guard

to the unit.

3. Lift up on panel and secure with tab on roof latch.

To secure internal guard:

1. Move holding tab on roof latch to release the panel,

then lower the panel into place.

2. Secure the panel with two bolts.

To remove front panel:

1. Remove the two bolts (H) that secure the panel to the unit.

2. Lift panel to remove from unit.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

To remove rear panel:

1. Insert key into lock (J) of rear panel. Turn key one

quarter turn counterclockwise to unlatch.

2. Open panel so that it clears the hinges.

3. Lift panel to remove from unit.

To secure rear panel:

1. Slide panel into place on unit.

2. Secure the panel with keyed lock (turn clockwise to

latch).

G

H

J

13

System Control Panel

Compare this control panel illustration with your generator to familiarize yourself with the location of these important controls:

A - Menu/Programming Navigation Buttons — See Menu

section for details

B - USB Port — Authorized Dealer Service Use Only

C - Generator Operation Control Buttons —

• “AUTO” Normal operating position. Press and hold

button to put unit into Automatic mode. If an utility

power outage is sensed, the system will start the

generator. When utility power is restored, auto lets the

engine stabilize internal temperatures, shuts off the

generator, and waits for the next utility outage.

• “OFF” Turns off running generator, prevents unit from

starting, and resets any detected service codes.

OFF must be pressed and held for more than 5

seconds in order to reset service codes.

• “MANUAL” Used to manually start the generator.

• “AUTO” LED — LED will light when unit is placed into

Auto mode. LED will blink if exercise cycle is not set or

set to OFF.

D - 15 Amp Fuse — Protects the standby generator DC

control circuits. If the fuse has ‘blown’ (melted open) or

was removed, the engine cannot crank or start. Replace

the fuse using only an identical ATO 15A fuse. One

spare fuse is supplied with the unit.

E - Cover — This protective cover must be opened to access

the fuse and the USB port.

F - Digital Display — Displays generator mode, menu

options, service codes, and service engine indicators.

MENU

ESC

AUTO OFF

MANUAL

A

B

C

F

E

D

14 BRIGGSandSTRATTON.COM

Menu

The following chart shows the icons for the buttons that control the system control panel.

The following chart describes key sequences for accessing different programming modes;

MENU

ENTER THE MENU (VIEW SETTINGS)

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT)

RETURN TO LAST MENU ITEM

RIGHT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

LEFT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

MANUAL MODE

USED TO MANUALLY START THE GENERATOR. PRESS AND HOLD BUTTON TO

START THE GENERATOR.

OFF

TURNS OFF RUNNING GENERATOR, PREVENTS UNIT FROM STARTING, AND

RESETS ANY DETECTED FAULTS.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO PLACE UNIT

INTO AUTOMATIC MODE. IF A UTILITY POWER OUTAGE IS SENSED, THE

SYSTEM WILL START THE GENERATOR. WHEN UTILITY POWER IS RE-

STORED, AUTO LETS THE ENGINE STABILIZE INTERNAL TEMPERATURES,

SHUTS OFF THE GENERATOR, AND WAITS FOR THE NEXT UTILITY POWER

OUTAGE.

GENERAL

SET-UP

PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT]

FOR THREE SECONDS TO ENTER THE PROGRAM MODE.

ADVANCED

SETTINGS

PRESS AND HOLD [ARROW LEFT, ARROW RIGHT AND

ESC] FOR THREE SECONDS TO ENTER THE ADVANCED

SETTINGS MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE SEC-

ONDS TO ENTER THE WIRELESS LINKING MODE.

15

General Set Up Screen

For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as outlined below.

NOTICE Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle was also set at

the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard Time. To update or change these

settings, follow the steps below.

SET DATE

If set to OFF, display will read:

EXERCISE CYCLE OFF

IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 30 SECONDS,

THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.

or

YEAR

FLASHING

MONTH

FLASHING

DAY##

FLASHING

SET TIME

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

or or or

or

or or or

or

or or or or

DAY OF WEEK

FLASHING

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

SET EXERCISE CYCLE

EVENT LOG

Display will scroll last service code event, date, time,

and temperature of when the event occurred.

or

16 BRIGGSandSTRATTON.COM

General System Parameters

To view general system parameters, press the MENU button.

The following will scroll across the digital display and then

move to the next item:

• Run time

• Date

• Time

• Exercise Cycle date and start time

The user can press the LEFT ARROW or RIGHT ARROW at

any time to move to the next item.

The user can press ESCAPE to go back to GENERATOR

READY.

If no user inputs are made for 10 seconds after all the items

have been displayed, the control board will reset to

GENERATOR READY.

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

• GENERATOR READY - if the unit is in standby and

utility power is present.

• GENERATOR ON - if the unit is running and utility

power is not present.

• SERVICE CODE - if a system service code has been

detected.

AUTOMATIC MODE

GENERATOR READY OR SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

GENERATOR ON

(When Generator Running - Auto Mode)

(MENU)

RUN TIME

or

TIME

DATE

EXERCISE CYCLE

17

Automatic Operation Sequence

The generator’s control board constantly monitors utility

voltage. Should utility voltage drop below a preset level, the

control board will signal the engine to crank and start.

When utility voltage is restored above a preset voltage level,

the engine is signaled to shut down.

The actual system operation is not adjustable and is

sequenced by sensors and timers on the control board,

as follows:

Utility Voltage Dropout Sensor

• This sensor monitors utility source voltage.

• If utility source voltage drops below about 70 percent of

the nominal supply voltage, the sensor energizes a

6 second timer. The timer is used to ‘sense’ brown-outs.

• Once the timer has expired, the engine will crank

and start.

Utility Voltage Pickup Sensor

This sensor monitors utility power voltage. When utility

voltage is restored above 80 percent of the nominal source

voltage, a time delay starts timing and the engine will go to

engine cool-down.

Engine Cool-down Timer

When utility power is sensed and the load transfers to the

utility source, the engine will go into a cool down period as

described below:

• If the generator has run for MORE than 5 minutes, once

the utility transfer occurs, the engine will continue to

run for about 1 minute before shutting down.

• If the generator has run for LESS than 5 minutes, once

the utility transfer occurs, the engine will continue to

run until 5 minutes has elapsed before shutting down.

Operation

Important Owner’s Considerations

Engine Oil

The engine is shipped from the factory pre-run and filled

with synthetic oil (API SJ/CF 5W-30). This allows for system

operation in a wide range of temperature and climate

conditions. Before starting the engine, check oil level and

ensure that engine is serviced as described in Maintenance.

Battery

The installer must supply a rechargeable 12 volt DC starting

battery. See Battery in Final Installation Considerations in the

installation manual.

With the battery installed, all wiring to transfer switch and

generator completed, utility power supplied to the automatic

transfer switch, and the unit in AUTO mode, the battery

receives a trickle charge while the engine is not running. The

trickle charge cannot be used to recharge a battery that is

completely discharged.

15 Amp Fuse

The generator’s 15 Amp fuse is critical to correct system

operation. The 15 Amp fuse was removed at the factory.

Your installer will ensure the fuse is properly installed upon

completion of the installation.

NOTICE Any attempt to crank or start the engine before it

has been properly serviced with the recommended coolant

and oil will result in equipment failure.

• Refer to the Maintenance section for coolant and oil fill

information.

• Damage to equipment resulting from failure to follow this

instruction will void engine and generator warranty.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

CAUTION Installing the 15A fuse could cause the

engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed from the

control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has

been completed and inspected.

18 BRIGGSandSTRATTON.COM

Setting Exercise Timer

The generator is equipped with an exercise timer. During the

exercise period, the unit runs for approximately 20 minutes

and then shuts down. Electrical load transfer DOES NOT

occur during the exercise cycle (unless an utility power

outage occurs).

The generator will only enter the exercise cycle if the unit is

in the AUTO mode and this exact procedure is followed.

To set the exercise timer:

NOTICE The generator is set with a default code exercise

cycle setting of Tuesday at 2:00 P.M. Central Time. To

change the cycle setting, proceed to the following steps:

1. Choose the day and time you want your generator to

exercise.

2. Press and hold the left arrow and right arrow

simultaneously for 3 seconds to enter the General Set-

Up program mode. See General Set-Up flow chart in

Menu Section.

3. Verify and/or set the time and date on the unit.

4. Go to the SET EXERCISE prompt and hit the “OK”

button.

NOTICE Items will flash until they are selected.

SELECT DAY: Use the left or right arrow to toggle

through the days of the week, Once the day is selected,

hit the “OK” button.

SELECT HOUR: Use the left or right arrow to toggle

through between 1 and 12. Choose the hour of day you

want the generator to exercise then hit the “OK” button.

SELECT MINUTE: Use the left of right arrow to toggle

between :00 and :59. Choose the minute of the day you

want the generator to exercise then hit the “OK” button.

SELECT AM/PM: Use the left of right arrow to toggle

between AM and PM. Once chosen, hit the “OK” button.

NOTICE During the weekly exercise cycle, the generator will

run for 20 minutes, but it will not supply power to the home.

During the exercise cycle, the optional in-home monitor will

continue blinking the GENERATOR READY green LED.

If you want to change the day and time the unit exercises,

simply perform the procedure again.

To turn off the generator exercise cycle, go to the OFF

selection within the day of the week menu and press OK. The

display will then scroll: EXERCISE CYCLE OFF.

Maintenance

Servicing the System

Before performing any generator maintenance, always

perform the following steps:

1. Set generator’s circuit breaker to its OFF position.

2. Press and hold the control board OFF button.

3. Remove 15 Amp fuse from control board.

4. Utility voltage is present at generator control board.

Disconnect power before servicing control board by

removing the fuses from the transfer switch.

5. After all servicing has been completed, replace fuses in

transfer switch, replace 15 Amp fuse in control board,

set circuit breaker ON and press and hold control board

AUTO button.

Service Code Detection System

The generator may have to run for long periods of time with

no operator present. For that reason, the system is equipped

with sensors that automatically shut down the generator in

the event of potentially damaging conditions, such as low oil

pressure, high temperature, over speed, and other conditions.

The generator’s control board shows service code

descriptions scrolling across the digital display. The service

code descriptions are listed below:

• Low Battery Voltage

• Low Oil Pressure

• Under Voltage

• Over Voltage

• Engine Does Not Start

• Low Frequency

• Engine Overspeed

• High Coolant Temperature

• Transfer Switch Service code

• Battery Charge Circuit

• Service Engine

19

Reset Service Code Detection System

The operator must reset the service code detection system

each time it activates. To do so, press the control board

OFF button for 5 seconds. Once the display turns off, leave

it off for at least 30 seconds. Remedy the service condition,

then return the standby generator to service by pressing and

holding the control board AUTO button and installing the 15

Amp fuse (if removed).

Low Battery Voltage

This service code is indicated by Low Battery Voltage

scrolling across the digital display. This condition occurs if

the battery voltage drops below the preset value. Causes for

this problem may be a service code battery or battery charge

circuit. See Battery Charge Circuit.

Remove the 15 Amp fuse and disconnect the battery from

the generator. Test the battery voltage. If voltage meets

specifications, take the battery to a local battery store for

analysis. Or contact your local service center for assistance.

Reinstall the battery (replace if necessary - see Battery in

Final Installation Considerations in the installation manual).

Then reset the service code detection system, as described

earlier.

Low Oil Pressure

This service code is indicated by Low Oil Pressure scrolling

across the digital display. The unit is equipped with an oil

pressure sensor that is monitored by the engine ECU. Should

oil pressure drop below the 50 psi range, the engine will shut

down.

To remedy the low oil pressure condition, add the

recommended oil to the FULL mark on the dipstick.

If the low oil pressure condition still exists, the engine will

start, then shut down again. The service code will appear. In

this case, contact an authorized dealer.

Under Voltage

This service code is indicated by Under Voltage scrolling

across the digital display. This condition is caused by a

restriction in the fuel flow, the electronic governing system

not functioning properly, a broken or disconnected sensing

lead, a failed alternator winding, the control board circuit

breaker is open, or the generator is overloaded.

To remedy the problem, contact your installer or an

authorized dealer.

Over Voltage

This service code is indicated by Over Voltage scrolling

across the digital display. This feature protects devices

connected to the transfer switch by shutting the generator

down if the generator output voltage happens to increase

above the preset limit.

This condition is most likely caused by a failed voltage

regulator, alternator excitation circuit or a load imbalance. To

remedy the problem, contact your installer or an

authorized dealer.

Engine Does Not Start

This service code is indicated by Engine Does Not Start

scrolling across the digital display. This feature prevents the

generator from damaging itself if it continually attempts to

start in spite of another problem, such as no fuel supply.

Each time the system is directed to start, the unit will

crank for 10 seconds, pause for 10 seconds, and repeat.

If the system does not begin producing electricity after

approximately 2 minutes, the unit will stop cranking.

The most likely cause of this problem is no fuel supply or

incorrect fuel selector setting. See Fuel Selection Switch in

the installation manual. Check the internal and external fuel

shut off valves to ensure they are fully open. Other causes

could be failed spark plug(s), a loose electronic governor

connection, a failed engine ignition, or the engine air filter

is clogged. You may need to contact your installer for

assistance if you can’t remedy these problems.

Low Frequency

This service code is indicated by Low Frequency scrolling

across the digital display. This feature protects devices

connected to the transfer switch by shutting the generator

down if the engine runs slower than 55 Hz for three

seconds. To resolve the problem, contact your installer or an

authorized dealer.

Engine Overspeed

This service code is indicated by Engine Overspeed scrolling

across the digital display. To resolve the problem, contact

your installer or an authorized dealer.

Service Engine

The engine is equipped with on-board diagnostics that

monitor the operation of emission related components. If

an emission related problem has been detected, the system

control panel will display Service Engine. If Service Engine

displays while the generator is running, a diagnostic trouble

code may be set or a problem may exist in the system which

has caused the engine emissions to go outside the standards

certified by the Environmental Protection Agency. It is the

responsibility of the operator to contact an authorized service

technician to repair this condition.

20 BRIGGSandSTRATTON.COM

High Coolant Temperature

This service code is indicated by High Coolant Temperature

scrolling across the digital display. The unit is equipped with

a coolant temperature sensor that is monitored by the engine

ECU. If the engine temperature increases past a determined

temperature, the service code is detected and the engine shuts

down.

Common causes for this condition include running the unit

with an access doors removed, obstructed air inlet or exhaust

port, or debris in the engine compartment or running unit

with roof open.

To resolve the problem, let the engine cool down and remove

any accumulated debris and obstructions. Ensure that the

access doors are installed and the roof is closed whenever

the unit is running. If problem persists, contact your installer

or authorized dealer.

Transfer Switch Service code

This service code is indicated by Transfer Switch Service

code scrolling across the digital display (if transfer switch is

equipped with service codedetection).

The most likely cause of this service code is a blown fuse

in the transfer switch. To remedy the problem, contact your

installer or an authorized dealer.

Battery Charge Circuit

This service code is indicated by Battery Charge Circuit

scrolling across the digital display. The most likely cause is

an electrical problem with the control panel. To remedy the

problem, contact your installer or an authorized dealer.

Generator Maintenance

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

generator as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart.

Generator maintenance consists of keeping the unit

clean. Operate the unit in an environment where it will

not be exposed to excessive dust, dirt, moisture or any

corrosive vapors. Cooling air louvers on the enclosure

must not become clogged with snow, leaves, or any other

foreign material. To prevent generator damage caused by

overheating, keep the enclosure cooling inlets and outlets

clean and unobstructed at all times.

Check the cleanliness of the unit frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible

on its exterior/interior surface. Inspect the air inlet and outlet

openings inside and outside the enclosure to ensure air flow

is not blocked.

DO NOT use direct spray from a garden hose to clean

generator. Water can enter the engine and generator and

cause problems.

NOTICE Improper treatment of generator could damage it

and shorten its life.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

Clean the generator as follows:

1. Press and hold the control board OFF button.

2. Remove 15 Amp fuse from control board.

3. Clean generator as desired.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft, bristle brush to loosen caked on dirt, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and openings on

the generator. These openings must be kept clean and

unobstructed.

4. Reinstall 15 Amp fuse in control board.

5. Press and hold the control board AUTO button.

La page charge ...

Simplicity 076109 Manuel utilisateur

Ce manuel convient également à

Simplicity 076109 Manuel utilisateur

dans d''autres langues

Documents connexes