Simplicity 030607-01 Manuel utilisateur

Not for

Reproduction

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 80009046 Revision -

Portable Generator

Operator’s Manual

This generator is certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-04

(motors and generators) and rated in accordance with PGMA (Portable Generator Manufacturers’ Association)

standard PGMA G200 (Standard for Testing and Validating Performance of Portable Generators).

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® generator. We are pleased that you’ve placed your confidence

in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs &

Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator products

and how to avoid them. This generator is designed and intended only for supplying electrical power for operating compatible

electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is important that you read

and understand these instructions thoroughly before attempting to start or operate this equipment. Save these original

instructions for future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages. There

are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Generator

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

BRIGGS & STRATTON POWER PRODUCTS is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Not for

Reproduction

3

Safe Operation Checklist

Safe operation of the portable generator requires the completion of the following tasks:

Carbon Monoxide (CO) Alarm

Carbon monoxide (CO) alarm(s) in working order.

Smoke Alarm

Smoke alarm(s) in working order.

Generator Location

Generator placed in a Carbon Monoxide (CO) safe zone. See Generator Location to reduce the Risk of Carbon Monoxide

Poisoning.

Generator placed in a fire safe zone. See Generator Location to reduce the Risk of Fire.

Generator located on flat and level surface.

Oil and Fuel

Engine has proper oil level. See Verify Engine Oil Level.

Fuel tank filled at or below baffle. See Add Fuel.

Inspect fuel lines, tank, cap and fittings each time before using generator. DO NOT use if fuel leak or damage is found.

Electrical

When connecting to a buildings electrical system install listed transfer equipment. See Connecting to a Building’s

Electrical System.

Electrical cords are rated for intended loads. See Cord Sets and Receptacles.

Electrical cords do not run through doorways, windows, holes in ceilings, walls or floors.

Inspect electrical cords thoroughly before each use. DO NOT use if damaged.

All labeled electrical cord safeties are understood and being followed.

Operation

Start engine. See Starting the Engine.

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Table of Contents

Safe Operation Checklist...........................3

Operator Safety .................................5

Safety Labels ................................................5

Equipment Description.........................................7

Important Safety Information....................................7

Assembly .................................... 10

Unpack Generator ...........................................10

Install Wheel Kit.............................................10

Verify Engine Oil Level ........................................10

Add Fuel...................................................11

System Ground .............................................11

Connecting to a Building’s Electrical System.......................11

Portable Generator Location ...................................12

Features and Controls............................ 15

Cord Sets and Receptacles ....................................16

Operation .................................... 17

Starting the Engine...........................................17

Connecting Electrical Loads....................................18

Stopping the Engine..........................................18

Low Oil Shutdown ...........................................18

Cold Weather Operation.......................................18

Don’t Overload Generator......................................20

Maintenance .................................. 21

Maintenance Schedule ........................................21

Generator Maintenance .......................................21

Fuel Valve Maintenance .......................................21

Engine Maintenance..........................................22

Storage....................................................25

Troubleshooting................................ 26

Schematic .................................................27

Warranties ................................... 28

Emissions Control System Warranty .............................28

Generator Owner Warranty ....................................30

Specifications ................................. 32

Product Specifications ........................................32

Common Service Parts .......................................32

Not for

Reproduction

5

Operator Safety

Safety Labels

The generator safety labels shown below and on the next page are placed on your portable generator to draw attention to

potential safety hazards.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Not for

Reproduction

7

Equipment Description

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generator is an engine-driven, revolving field, alternating

current (AC) generator equipped with a voltage regulator.

The voltage regulator is designed to automatically maintain

a constant output voltage level. It was designed to supply

electrical power for operating compatible electrical lighting,

appliances, tools and motor loads. The generator’s revolving

field is driven at about 3600 rpm by a single cylinder engine.

NOTICE

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices connected

to it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

Every effort has been made to ensure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the generator and this documentation at any time

without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency

and the California Air Resources Board.

Important Safety Information

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm. Wash hands after handling.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury.

WARNING Fuel and its vapors are extremely

flammable and explosive which could

cause burns, fire or explosion resulting

in death or serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn generator engine OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for cracks or

leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building, carport,

porch, mobile equipment, marine applications, or enclosure.

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT stop engine by moving choke control to “Choke”

position

( ).

WHEN TRANSPORTING, MOVING OR REPAIRING EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

WARNING Starter cord kickback (rapid retraction)

will pull hand and arm toward engine faster than

you can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING POISONOUS GAS HAZARD. Engine

exhaust contains carbon monoxide, a poisonous

gas that could kill you in minutes. You CANNOT

smell it, see it, or taste it. Even if you do not

smell exhaust fumes, you could still be exposed to carbon

monoxide gas.

• Operate this product ONLY outside far away from windows,

doors and vents to reduce the risk of carbon monoxide gas

from accumulating and potentially being drawn towards

occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up according to

the manufacturer’s instructions. Smoke alarms cannot detect

carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements,

crawlspaces, sheds, or other partially-enclosed spaces even

if using fans or opening doors and windows for ventilation.

Carbon monoxide can quickly build up in these spaces and can

linger for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine

exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

Not for

Reproduction

9

NOTICE

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices connected

to it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting electrical

loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

NOTICE

Improper treatment of generator could damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate generator without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION Excessively high operating speeds could

result in minor injury.

Excessively low operating speeds impose a heavy load.

• DO NOT tamper with governor spring, links or other parts

to increase engine speed. Generator supplies correct rated

frequency and voltage when running at governed speed.

• DO NOT modify generator in any way.

WARNING

Generator voltage could cause electrical

shock or burn resulting in death or serious

injury.

• Use listed transfer equipment, suitable for the intended use,

to prevent backfeed by isolating generator from electric utility

workers.

• When using generator for backup power, notify utility company.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5feet (1.5m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING Unintentional sparking could cause fire or

electric shock resulting in death or

serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

Assembly

Your generator requires some assembly and is ready for use

after it has been properly serviced with the recommended

fuel and oil level is verified.

If you have any problems with the assembly of your generator,

please call the generator helpline at (800) 743-4115. If calling

for assistance, please have the model, revision, and serial

number from the identification label available.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from

top to bottom.

4. Leave generator on carton to install wheel kit.

The generator is supplied with:

• Operator’s manual

• Wheel kit

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road use.

Install the wheel kit as follows:

1. Tip generator so that engine end is up.

2. Slide a washer (A) over axle stud (B).

3. Slide a wheel (C) over axle stud (B).

NOTICE Be sure to install wheel with raised hub inboard.

4. Slide axle stud (B) through mounting bracket.

5. Insert retaining pin (D) through hole on axle stud.

6. Repeat steps 2 thru 5 to secure second wheel.

7. Line up holes in support leg (E) with holes in generator

frame.

8. Attach support leg using four capscrews (F) and four

flange nuts (G). Tighten with 10 and 13mm wrenches.

9. Return generator to normal operating position (resting

on wheels and support leg).

Verify Engine Oil Level

The generator engine is shipped from the factory filled with

oil (API SJ or higher 10W-30). This allows for generator

operation in the widest range of temperature and climate

conditions. Before starting the engine, check oil level and

ensure that engine is serviced as described in Maintenance.

NOTICE Any attempt to crank or start the engine before

it has been properly filled with the recommended oil could

result in equipment failure.

• Refer to Maintenance for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTICE See Oil in the Maintenance section to review oil

recomendations. Verify provided oil in engine is the correct

viscosity for current ambient temperature.

D

A

B

C

G

E

F

Not for

Reproduction

11

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For high

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Use of unapproved fuels could damage generator

and voids warranty.

• DO NOT use unapproved gasoline such as E15 and E85.

• DO NOT mix oil in gasoline or modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems after

using fuel, switch to a different fuel provider or change brands.

This engine is certified to operate on gasoline. The emission

control system for this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank (B).

Be careful not to fill above the baffle (C). This allows

adequate space for fuel expansion as shown.

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption, and

increased emissions. See an authorized dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on the

AC output receptacles. The system ground is connected to the

AC neutral wire (the neutral is bonded to the generator frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must use a listed transfer switch installed by a

current licensed electrician. The connection must isolate the

generator power from the utility power and must comply

with all applicable laws and electrical codes.

FUEL

TANK

C

B

A

WARNING

Generator voltage could cause electrical

shock or burn resulting in death or serious

injury.

• Use listed transfer equipment, suitable for the intended use,

to prevent backfeed by isolating generator from electric utility

workers.

• When using generator for backup power, notify utility company.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Fuel and its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death or

serious injury.

WHEN ADDING FUEL

• Turn generator engine OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for cracks or

leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Portable Generator Location

Before starting the portable generator there are two equally

important safety concerns regarding carbon monoxide (CO)

poisoning and fire that must be addressed.

NOTICE Satisfying the RISK OF CARBON MONOXIDE

POISONING location requirements may not satisfy the fire

location requirements. Satisfying the RISK OF FIRE location

requirements may not satisfy the CARBON MONOXIDE

POISONING location requirements.

Operation Location of Portable Generator to REDUCE

THE RISK OF CARBON MONOXIDE POISONING

All fossil fuel burning equipment, such as a portable

generator, contains carbon monoxide (CO) gas in the engine

exhaust, a poisonous gas that could kill you in minutes.

You CANNOT smell it, see it, or taste it. Even if you do not

smell exhaust fumes, you could still be exposed to carbon

monoxide gas. The following must be completed prior to

starting the portable generator engine:

• By law it is required in many states to have a Carbon

Monoxide (CO) alarm (A) in operating condition in

your home. Install/maintain battery-operated carbon

monoxide alarms or plug-in carbon monoxide alarms

with battery back-up according to the manufacturer’s

instructions. A CO alarm is an electronic device that

detects hazardous levels of CO. When there is a buildup

of CO, the alarm will alert the occupants by flashing

visual indicator light and alarm. Smoke alarms cannot

detect CO gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

• Your neighbor(s) home may be exposed to the engine

exhaust from your portable generator and must be

considered when deciding on a location for the safe

operation of your portable generator.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

A

Not for

Reproduction

13

EXAMPLE OF LOCATION TO REDUCE THE RISK OF CARBON MONOXIDE POISONING

DO NOT OPERATE IN ANY OF THE FOLLOWING LOCATIONS

Only use OUTSIDE and

FAR AWAY from windows,

doors and vents.

Direct exhaust AWAY

from windows, doors,

and vents.

KEEP

FAR AWAY

CO Alarm

in Living Areas

E

X

H

A

U

S

T

(

C

O

)

Generator too

close to home and

exhaust directed

towards windows,

doors and vents.

Garage

Attic

Living Area

Basement

Crawlspace

Entryway,

Porch,

Mud Room

E

X

H

A

U

S

T

(

C

O

)

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

EXAMPLE OF LOCATION TO REDUCE THE RISK OF FIRE

Operation Location of Portable Generator to REDUCE

THE RISK OF FIRE

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Portable generator must be at least 5feet (1.5m) from any

structure, overhang, trees, windows, doors, any wall opening,

shrubs, or vegetation over 12 inches (30.5 cm) in height.

• DO NOT place portable generator under a deck or other type of

structure that may confine airflow.

• Smoke alarm(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/recommendations.

Carbon monoxide alarms cannot detect smoke.

• DO NOT place portable generator in manner other than shown.

Direct exhaust AWAY from

windows, doors, and vents.

E

X

H

A

U

S

T

(

C

O

)

5 ft. (1.5 m) min.

Not for

Reproduction

15

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A - Engine Switch — Set this switch to on (I) before starting

engine. Set switch to off (O) to shut off engine.

B - Hour Meter — Displays and records how many hours

your generator has run (up to 9,999.9).

C - Main Breaker — The receptacles are provided with

a rocker switch main circuit breaker to protect the

generator against electrical overload.

D - 120/240 Volt AC, 30 Amp Locking Receptacle — May

be used to supply electrical power for the operation of

120and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical, lighting, appliance, tool and motor loads.

E - Circuit Breakers (AC) — The 120 Volt AC, 20A duplex

receptacles are provided with “push to reset” circuit

breakers to protect the generator against electrical

overload.

F - 120 Volt AC, 20 Amp, Duplex Receptacles — May

be used to supply electrical power for the operation of

120Volt AC, 20 Amp, single phase, 60 Hz electrical,

lighting, appliance, tool and motor loads.

G - Oil Fill Cap/Dipstick — Check and add engine oil here.

H - Oil Drain Plug — Drain engine oil here.

J - Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

K - Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

L - Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

M - Choke Lever — Used when starting a cold engine.

N - Recoil Starter — Used to start the engine manually.

P - Fuel Valve — Used to turn fuel supply on and off to

engine.

R - Fuel Tank — Capacity of 7.5 U.S. gallons (28.4 l).

Items Not Shown:

Engine Identification — Provides model, type and code

of engine. Please have these readily available if calling for

assistance.

Identification Label — Provides model, revision and serial

number of generator. Please have these readily available

when calling for assistance.

G

A

R

B

L

C

D

N

K

M

E

F

H

J

P

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded extension

cords with the generator’s receptacles. Inspect extension

cords before each use.

Check the ratings of all extension cords before you use

them. Check the operator’s manuals of devices for the

manufacturer’s recommendations.

A double pole rocker switch main circuit breaker is provided

to protect the locking receptacle. If this circuit breaker is

tripped, all receptacles are disconnected.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14-30 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater). You can use the same 4-wire cord if you plan to

run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 5000 watts of power (5.0kW) at

20.8 Amps for 240 Volts or two independent 120 Volt loads

at 20.8 Amps each. The outlet is protected by a two pole

rocker switch circuit breaker.

NOTICE

Receptacles may be marked with rating value

greater than generator output capacity.

• NEVER attempt to power a device requiring more amperage than

generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload Generator.

120 Volt AC, 20 Amp, Duplex Receptacles

The generator has three 120 Volt, 20 Amp duplex

receptacles. The receptacles are protected against overload

by push-to-reset circuit breakers.

Use each receptacle to operate 120Volt AC, single-phase,

60Hz electrical loads requiring up to 2,400watts (2.4kW) at

20Amps of current. Use cord sets that are rated for 125Volt

AC loads at 20Amps (or greater). Inspect cord sets before

each use.

WARNING Damaged or overloaded electrical cords

could overheat, arc, and burn resulting in death

or serious injury.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

• Inspect cord sets before each use.

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

4-Wire Cord Set

Not for

Reproduction

17

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is on a level surface.

NOTICE Failure to start and operate the unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn the fuel valve (A) to the “On” position.

3. Push choke lever (B) to “Choke” position ( ).

4. Set engine switch (C) to on (I) position.

5. Grasp recoil handle and pull slowly until slight

resistance is felt. Then pull rapidly one time only to

start engine.

• If engine starts, proceed to step 7.

• If engine fails to start, proceed to step 6.

6. Move choke lever to “Half” choke position, and pull

recoil handle twice.

• If engine fails to start, repeat steps 5 thru 7.

7. Slowly move choke lever to “Run” position (

). If

engine falters, move choke lever to “Half” choke

position until engine runs smoothly, and then to “Run”

position ( ).

NOTICE If engine floods, place choke lever in “Run”

position ( ) and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on a

level surface and check for proper oil level in crankcase. This

unit may be equipped with a low oil protection device. If so,

oil must be at proper level for engine to start.

A

C

WARNING Starter cord kickback (rapid retraction)

will pull hand and arm toward engine faster than

you can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5feet (1.5m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

B

Not for

Reproduction

18 BRIGGSandSTRATTON.COM

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few minutes

after starting.

2. Ensure main breaker is in “On” position.

3. Plug in and turn on the desired 120 and/or 240Volt

AC, single phase, 60Hz electrical loads.

NOTICE When plugging into the 120 Volt receptacles, plug

items to be powered in sequence as shown below.

NOTICE

• DO NOT connect 240Volt loads to 120Volt duplex

receptacles.

• DO NOT connect 3-phase loads to generator.

• DO NOT connect 50Hz loads to generator.

• DO NOT OVERLOAD THE GENERATOR. See Don’t

Overload Generator.

NOTICE

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices connected

to it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting electrical

loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned ON.

2. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

3. Push engine switch to OFF (O) position.

4. Move fuel valve to “Off” position.

Low Oil Shutdown

If the engine oil drops below a preset level, an oil switch will

stop the engine. Check oil level with dipstick.

If oil level is between ADD and FULL mark on dipstick:

1. DO NOT try to restart the engine.

2. Contact an Authorized Briggs & Stratton Service Dealer.

3. DO NOT operate engine until oil level is corrected.

If oil level is below ADD mark on dipstick:

1. Add oil to bring level to FULL mark.

2. Restart engine and if the engine stops again a low oil

condition may still exist. DO NOT try to restart the

engine.

3. Contact an Authorized Briggs & Stratton Service Dealer.

4. DO NOT operate engine until oil level is corrected.

Cold Weather Operation

Under certain weather conditions (temperatures below 40°F

[4°C] combined with high humidity), your generator may

experience icing of the carburetor and/or the crankcase

breather system. To reduce this problem, you need to

perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil.

4. Check oil level daily or after every eight (8) hours of

operation.

5. Maintain generator following Maintenance Schedule in

Maintenance section.

6. Shelter unit from elements.

WARNING Fuel and its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death or

serious injury.

• DO NOT stop engine by moving choke lever to “Choke” position

( ).

1

4

3

2

5

6

Not for

Reproduction

19

Creating a Temporary Cold Weather Shelter

1. For temporary shelter, the original shipping carton can

be used.

2. Cut off top carton flaps and one long side of carton to

expose muffler side of unit. If required, tape up other

sides of carton to fit over generator as shown.

NOTICE If required, remove wheel kit to fit carton over

generator as shown.

3. Cut appropriate slots to access receptacles of unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section Generator

Location. Keep exhaust gas from entering a confined

area through windows, doors, ventilation intakes or

other openings.

6. Start generator as described in the section Starting

the Engine, then place carton over generator. Keep at

least 5 ft. (1.5 m) clearance on all sides of generator

including overhead with shelter in place.

7. Remove shelter when temperatures are above 40°F

[4°C].

8. Turn engine OFF and let cool two (2) minutes before

refueling. Let any spilled fuel evaporate before starting

engine.

Building a Cold Weather Shelter

1. Using non combustible material with a fire rating of at

least one hour, build a shelter that will enclose three

sides and the top of the generator. Make sure muffler

side of generator is exposed.

NOTICE Contact your local building material supplier for

non combustible materials with a fire rating of at least one

hour.

NOTICE Be sure shelter can easily be repositioned for

change in wind direction.

2. DO NOT enclose generator any more than shown.

Shelter should hold enough heat created by the

generator to prevent icing problem.

NOTICE If a wheel kit is installed on the generator, enlarge

shelter accordingly.

3. Follow steps 3 through 8 as described previously in

Creating a Temporary Cold Weather Shelter.

Wind

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5feet (1.5m) of clearance on all sides of

generator including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

WARNING POISONOUS GAS HAZARD. Engine

exhaust contains carbon monoxide, a poisonous

gas that could kill you in minutes. You CANNOT

smell it, see it, or taste it. Even if you do not

smell exhaust fumes, you could still be exposed to carbon

monoxide gas.

• Operate this product ONLY outside far away from windows,

doors and vents to reduce the risk of carbon monoxide gas

from accumulating and potentially being drawn towards

occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up according to

the manufacturer’s instructions. Smoke alarms cannot detect

carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements,

crawlspaces, sheds, or other partially-enclosed spaces even

if using fans or opening doors and windows for ventilation.

Carbon monoxide can quickly build up in these spaces and can

linger for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine

exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

Not for

Reproduction

20 BRIGGSandSTRATTON.COM

Don’t Overload Generator

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is the

amount of power your generator must produce to keep

your items running. See Wattage Reference Guide.

3. Estimate how many surge (starting) watts you will need.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge (Starting) Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity, as

described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge (Starting)

Watts

Essentials

Light Bulb - 75 watt 75 -

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 Cu. Ft. 800 1600

Water Well Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 HP 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 -

Coffee Maker 1500 -

Electric Stove - Single Element 1500 -

Hot Plate 2500 -

Family Room

DVD/CD Player 100 -

VCR 100 -

Stereo Receiver 450 -

Color Television - 27” 500 -

Personal Computer w/17” monitor 800 -

Other

Security System 180 -

AM/FM Clock Radio 300 -

Garage Door Opener - 1/2 HP 480 520

Electric Water Heater - 40 Gallon 4000 -

DIY/Job Site

Quartz Halogen Work Light 1000 -

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 HP 1000 1000

Circular Saw - 7 1/4” 1500 1500

Miter Saw - 10” 1800 1800

Table Planer - 6” 1800 1800

Table Saw/Radial Arm Saw - 10” 2000 2000

Air Compressor - 1-1/2 HP 2500 2500

Tool or Appliance Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 —

Light (75 Watts) 75 —

3075 Total

Running Watts

1800 Highest

Additional Surge Watts

La page charge ...

Simplicity 030607-01 Manuel utilisateur

Simplicity 030607-01 Manuel utilisateur

dans d''autres langues

Documents connexes