Yamaha RS-80 Le manuel du propriétaire

Catégorie
Destinataire
Taper
Le manuel du propriétaire

Ce manuel convient également à

e
e
w
q
w
t
y
w
w
A
B
C
D
E
F
G
H
H
H
H
H
I
I
J
J
K
K
r
Electronic Drum Rack System
RS-80
Assembly Instructions
RS-80 Rack Stand Parts RS-80
+
Pad grouping : Set up example
* Before assembling the rack stand, make sure all of the parts shown below
are included.
Left Side Assembly (x1)
A
B
Right Side Arm (x1)
Right Side As-
sembly (x1)
C
H
Hex Rod Cylinder (x6)
N
Assembly Instructions
(this sheet)
Module Holder Clamp (x1)
G
M
Tuning Key (x1)
F
Module Holder (x1)
(4 screws included)
L
Cable Band (x10)
K
Cymbal Holder (x2)
J
Drum Pad Clamp (Long) (x3)
Center Pipe Assembly (x1)
D
I
Drum Pad Clamp (Short) (x2)
E
Center Bar (x1)
r KP80
Kick Pad
t HH80
Hi-hat Control Pedal
q DTX
Drum Trigger Module
w TP80S/TP80
Drum Pad
e PCY80S/PCY80
Cymbal Pad
Pad and Drum Trigger Grouping (option)
Thank you for purchasing the Yamaha Electronic Drum Rack System RS-80.
Before using, thoroughly read this assembly manual, and use this product safely and correctly.
* Specifications are subject to change without notice.
y Foot Pedal
* FP-820 etc.
5
Attach the Drum Pad Clamps
5-1 Insert the Hex Rod Cylinders
H
into the Drum Pad Clamps
IJ
, and tighten the fixing bolts.
5-2 Attach the Drum Pad Clamps (Short)
I
to the snare drum
and floor tom positions.
The Drum Pad Clams (Long)
J
should be attached to the hi-
hat and tom tom positions.
5-3 Insert the Hex Rod Cylinders
H
in the pads, adjust the posi-
tion of the pad and tighten the fixing bolts.
1
Insert the Right Side Assembly
C
pipe into the Right Side Arm
B
,
and tighten the fixing bolts.
RS-80 Assembly
* A screw driver (+ or -) is necessary to complete the assembly.
2
Insert the Left Side Assembly
A
pipe and the Right Side Assembly
C
pipe into the Center Bar
E
, and tighten the fixing bolts.
Make sure that the Left and Right Side Assemblies are not reversed.
Over-tightening of the fixing bolts may result in damage.
Take care when tightening fixing bolts and screws.
3
Above the Center Bar
E
, attach the Center Pipe
D
, and tighten
the fixing bolts.
Tighten
Tighten
Tighten
Tighten
Center Bar
E
Step 3
Step 2
Step 1
Left Side Assembly
A
Right Side Arm
B
Attach the Center Pipe
D
Right Side Assembly
C
4
Attach the Module Holder
4-1 Insert the Hex Rod Cylinder
H
into the Module Holder Clamp
G
, and tighten the fixing bolts.
4-2 Attach the Module Holder Clamp
G
to the Left Side Assembly
A
pipe.
4-3 Attach the DTX to the Module Holder
F
. With a screwdriver,
use the screws included with the Module Holder to attach the
holder to the bottom of the DTX.
4-4 Attach the Module Holder
F
(with the DTX attached)
to the Module Holder Clamp
G
.
Hex Rod Cylinder
H
Attach the Module Holder
G
Tighten
DTX
Module Holder
F
Left Side Assembly
A
Step 4-3
Step 4-2
Step 4-1
Step 4-4
After the above assembly is complete, set the Kick Pad, Hi-Hat Con-
trol Pedal, etc. into position and connect the necessary cables. To
keep cable out of the way while playing, use the supplied Cable Bands
to hold the cables to the rack systems’s pipes.
Drum Pad
Clamp(short)
I
Drum Pad Clamp
(Long)
J
Step 5-1
Drum Pad Clamp
(Long)
J
Hex Rod Cylinder
H
Cymbal Holder
K
Tighten
Cymbal Holder
K
Step 6-1
Drum Pad
Clamp(short)
I
Step 5-2
Step 6-2
Step 5-3
Cymbal Pad
6
Attach the Cymbal Holders
6-1 Insert the Cymbal Holders
K
into the Cymbal Holder Clamps
that are attach to the left and right sides of the Center Pipe
D
, and tighten all fixing bolts.
6-2 Attach the Cymbal Pad to the Cymbal Holders
K
,
adjust the position and tighten the fixing bolts. (Refer to the
Cymbal Pad’s Owner’s Manual for instructions on attaching
the cymbal pad to the cymbal holder.)
1 / 1

Yamaha RS-80 Le manuel du propriétaire

Catégorie
Destinataire
Taper
Le manuel du propriétaire
Ce manuel convient également à