ZX10 NFC User Guide
R02
2021/10/25
2021/10/25
Select and click the “Getac Settings” APP
Select and click the “NFC reader” in “Getac Setting”
2021/10/25
Put the NFC tag on the NFC reader area of system backside surface.
NFC tag information show on the front side screen of “NFC Reader” .
2021/10/25
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
2021/10/25
IMPORTANT NOTE:
This NFC devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product. Any other installation or use will violate FCC Part 15 regulations.
Modifications not expressly approved by Getac could void your authority to
operate the equipment.
This module apply limit module approval, and just only install in end product
(Brand: Getac / Model: ZX10).
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power
if such function is available.
End Product Labeling:
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: QYLPN7150Z11”. The grantee‘s FCC ID can be used only when all
FCC compliance requirements are met.
2021/10/25
Manual Information to the End User:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
2021/10/25
Industry Canada Statement
Canada, Industry Canada (IC) Notices
Class B digital circuitry of this device complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Under Industry Canada regulations, the radio transmitter(s) in this device may only
operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
This module apply limit module approval, and just only install in end product
(Brand: Getac / Model: ZX10).
End Product Labeling:
The product can be kept as far as possible from the user body or set the device to
lower output power if such function is available.
The final end product must be labeled in a visible area with the following:
“Contains IC: 10301A-PN7150Z11”
2021/10/25
Manual Information to the End User:
The OEM integrator has to be aware not to provide information to the
end user regarding how to install or remove this RF module in the
user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information /
warning as show in this manual.
Radio Frequency (RF) Exposure Information
The radiated output power of this device is below the Industry Canada (IC) radio
frequency exposure limits. This device has been evaluated for and shown compliant
with the IC Radio Frequency (RF) Exposure limits. The device should be used in such a
manner such that the potential for human contact during normal operation is
minimized.
This device has been certified for use in Canada. Status of the listing in the Industry
Canada’s REL (Radio Equipment List) can be found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be found at the following
web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
2021/10/25
Canada, avis d'Industry Canada (IC)
La circuiterie numerique de Classe B de cet appareil est conforme a la norme
canadienne ICES-003.
Cet appareil est conforme aux normes d'exemption de licence RSS d'Industry
Canada.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne
doit pas causer d‘interference et (2) cet appareil doit accepter toute interference,
notamment les interferences qui peuvent affecter son fonctionnement.
Conformement aux reglementations d’Industry Canada, les emetteurs radio de cet
appareil ne peuvent fonctionner qu‘a l’aide d‘une antenne dont le type et le gain
maximal (ou minimal) pour ces emetteurs - transmetteurs sont approuves par
Industry Canada. Pour reduire le risque d’interference eventuelle pour les autres
utilisateurs, le type et le gain de l‘antenne doivent etre choisis de maniere a ce que
la puissance isotrope rayonnee equivalente (p.i.r.e.) minimale necessaire a une
bonne communication soit fournie.
Ce module applique l'approbation du module de limite et s'installe uniquement dans
le produit final (Marque : Getac / Modèle : ZX10).
Plaque signalétique du produit final
L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que
le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est
disponible. Le produit final doit être étiqueté dans un endroit visible avec
l'inscription suivante: "Contient des IC: 10301A-PN7150Z11".
2021/10/25
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF
dans le manuel de l'utilisateur du produit final qui intègre ce module. Le
manuel de l'utilisateur final doit inclure toutes les informations
réglementaires requises et avertissements comme indiqué dans ce manuel.
Informations sur l'exposition a la frequence radio (FR)
La puissance rayonnee de sortie de cet appareil est inferieure aux limites d‘exposition a
la frequence radio d’Industry Canada (IC). Cet appareil a ete evalue et juge conforme aux
limites d‘exposition a la frequence radio (FR) d’IC. Cet appareil devrait etre utilise de
maniere a ce que le risque de contact humain au cours d'un fonctionnement normal soit
reduit.
Cet appareil est homologue pour l'utilisation au Canada. Pour consulter l'entree
correspondant a l'appareil dans la liste d'equipement radio (REL - Radio Equipment List)
d'Industry Canada, rendez-vous sur:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Pour des informations canadiennes supplementaires sur l'exposition FR, rendez-vous sur :
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
2021/10/25
Antenna Information:
Label Sample
FCC ID: QYLPN7150Z11
IC: 10301A-PN7150Z11
PN7150
Antenna Antenna Net Gain (dBi) Frequency Range Antenna Type Connector Type
NFC antenna 0 13.56MHz Loop Antenna NA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
dans d''autres langues
- English: Getac ZX10 User guide
Autres documents
-
Asus I005D/I005DC ROG Phone 5 Mode d'emploi
-
Dell Chromebook 3110 11 Inch Laptop Mode d'emploi
-
Asus ZenFone AR Le manuel du propriétaire
-
SonicWALL TZ270W Mode d'emploi
-
Asus ZS661KS Mode d'emploi
-
Asus PCE-AC56 Guide de démarrage rapide
-
-
Turtle Beach Ear Force X32 Manuel utilisateur