Modern Forms PD-88344 Bentley Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
PD-88344
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 5pcs+1 Extra
Mounting Screw
Qty: 1 Extra
AB
Plastic Anchor
Qty: 2 pcs+1 Extra
Wood Screw
Qty: 2 pcs+1 Extra
CD
Safety Cord Gripper
Qty: 1 pc
Set Screws
Qty: 2 pcs+1 Extra
EF
2
INSTALLATION INSTRUCTIONS
PD-88344
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
3. Remove the mounting plate screw (B) and mounting plate from the xture.
4. Choose the number of down rods suitable for your application.
5. Thread the safety cords and xture wire through the rods, swivel and canopy.
Connect the canopy, rods, swivel, and xture body. Making sure all are tightened.
swivel through the canopy and tighten the fastening nut.
6. Loosen the set screws(E) on the safety cable gripper(F), thread the safety cords
through the gripper (F), mounting plate, and out the other end of the
gripper (F) as shown(Fig.1), then tighten the two set screws(E) and adjust the safety
cords length so there is ample room to work with.
7. Secure mounting plate to the junction box using junction box screws, The side of the mounting plate marked “GND” must face out.
8. Connect the driver’s output wires to center cable, red to the center, and black to the bare, make sure that wire connectors (B) are secured.
Then tuck them inside the canopy. Connect the driver’s input wires to junction box wires as shown (Fig. 2). Make sure that all
wire connectors (A) are secure. If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the back plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
9. Secure the xture to the mounting back plate using the mounting screw (B).
10. This xture features electronic low voltage (ELV or TRIAC) or 0-10V dimming capabilities. See notes below for specic dimming
wires information.
11. To utilize ELV or TRIAC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
12. To utilize 0-10V dimming: use wire purple (dim+), gray or pink (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
12"
9"
1 3/8" 1 3/4"
4 3/8"
Purple - Dim+
Pink or Gray - Dim-
White - Neutral
Black - Hot
Red +
Black -
Red +
Black - Output
Input
Driver
Driver
Junction box
Wire Connector
Mounting plate
Junction Box Screw
Mounting Screw
Fastening Nut
Fixture
A
B
6x12"Rods
ROD-I12-PC130T-AB
)
2x6"Rods
(
ROD-I06-PC130T-AB
)
Safety
C
ord
Safety Cord Gripper
Set Screws
Driver
Canopy
Wood Screw
Plastic Anchor
C
D
E
F
swivel
-
1
-
2
Modern Forms PD-88344 Bentley Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-82044 Double Bubble Mode d'emploi
-
-
-
-
-
-
-
-
-