VTech VS112-17 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
VS
112-2
112-27
112-3
112-37
112-4
112-47
Click on the in the manual
to watch the video tutorials.
User’s manual
Scan the QR code to go and
subscribe our tutorial channel
Congratulations
on purchasing your new VTech product. Before
using this telephone, please read Important safety
instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate your
new VTech telephone. Please review this manual
thoroughly to ensure proper installation and operation
of this innovative and feature rich VTech product.
For support, shopping, and everything new at
VTech, visit our website at www.vtechphones.com. In
Canada, please visit phones.vtechcanada.com.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identified
with this logo have
reduced noise and
interference when
used with most T-coil
equipped hearing aids
and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of
the Telecommunications
Industry Association.
Used under license.
The ENERGY STAR®
program (www.
energystar.gov)
recognizes and
encourages the use
of products that save
energy and help protect
our environment. We
are proud to mark
this product with the
ENERGY STAR® label
indicating it meets the
latest energy efficiency
guidelines.
Important safety instructions
When using your telephone equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on
the product.
3. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
4. CAUTION: Do not install the telephone base at a
height above 2 meters.
5. Do not use this product near water such as near a
bath tub, wash bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement or shower.
6. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
7. Avoid placing the telephone system in places
with extreme temperature, direct sunlight, or
other electrical devices. Protect your phone from
moisture, dust, corrosive liquids and fumes.
8. Slots and openings in the back or bottom of the
telephone base and handset are provided for
ventilation. To protect them from overheating,
these openings must not be blocked by placing
the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near
or over a radiator or heat register. This product
should not be placed in any area where proper
ventilation is not provided.
9. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home or office, consult your dealer
or local power company.
10. Do not allow anything to rest on the power cord.
Do not install this product where the cord may be
walked on.
11. Never push objects of any kind into this product
through the slots in the telephone base or handset
because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of
any kind on the product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the telephone base or handset other
than specified access doors may expose you
to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer
servicing to an authorized service facility under
the following conditions:
When the power supply cord or plug is
damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or
water.
If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operation instructions. Improper adjustment
of other controls may result in damage and
often requires extensive work by an authorized
technician to restore the product to normal
operation.
If the product has been dropped and the
telephone base and/or handset has been
damaged.
If the product exhibits a distinct change in
performance.
15. Avoid using a telephone (other than cordless)
during an electrical storm. There is a remote risk
of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the
vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is
plugged into the power outlet, or when the
handset is replaced in its cradle. This is a common
event associated with the closing of any electrical
circuit. The user should not plug the phone into
a power outlet, and should not put a charged
handset into the cradle, if the phone is located
in an environment containing concentrations of
flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in such an
environment could create a fire or explosion.
Such environments might include: medical use of
oxygen without adequate ventilation; industrial
gases (cleaning solvents; gasoline vapors; etc.); a
leak of natural gas; etc.
17. Only put the handset of your telephone next to
your ear when it is in normal talk mode.
18. The power adapter is intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
19. For pluggable equipment, the socket outlet shall
be installed near the equipment and shall be
easily accessible.
20. CAUTION: Use only the batteries
indicated in this manual. There may be a risk of
explosion if a wrong type of battery is used for
the handset. Use only the supplied rechargeable
batteries or replacement batteries (BT162342/
BT262342) for the handset. Do not dispose of
batteries in a fire. They may explode.
21. Use only the adapter included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Base unit power adapter: Output: 6V DC
600mA
Charge power adapter: Output: 6V DC
600mA
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use Only Supplied Battery. To
order a replacement, visit out website at www.
vtechphones.com or call 1 (800) 595-9511. In
Canada, go to phones.vtechcanada.com or call 1
(800) 267-7377.
Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
Exercise care in handling batteries in order not to
create a short circuit with conductive materials.
Charge the battery provided with this product
only in accordance with the instructions and
limitations specified in this manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital cordless
telephones):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless telephones and implanted cardiac
pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches
from the pacemaker.
• Should NOT place wireless telephones directly over
the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite
the pacemaker.
WTR’s evaluation did not identify any risk to bystanders
with pacemakers from other persons using wireless
telephones.
About cordless telephones
Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the
telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless
telephone conversations could be intercepted
by radio receiving equipment within range of
the cordless handset. For this reason, you should
not think of cordless telephone conversations as
being as private as those on corded telephones.
Electrical power: The telephone base of this
cordless telephone must be connected to a
working electrical outlet. The electrical outlet
should not be controlled by a wall switch. Calls
cannot be made from the cordless handset if the
telephone base is unplugged, switched off or if
the electrical power is interrupted.
Potential TV interference: Some cordless
telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize
or prevent such interference, do not place
the telephone base of the cordless telephone
near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone
farther away from the TV or VCR often reduces or
eliminates the interference.
Rechargeable batteries: Exercise care in handling
batteries in order not to create a short circuit with
conducting material such as rings, bracelets and
keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between
the battery and the battery charger.
Nickel-metal hydride rechargeable batteries:
Dispose of these batteries in a safe manner. Do not
burn or puncture the battery. Like other batteries
of this type, if burned or punctured, they could
release caustic material which could cause injury.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance. The
ECO mode activities automatically whenever the
handset is synchronized with the telephone base.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez
votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde
inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale
avant de le nettoyer. N’utilisez pas de nettoyeurs
liquides ni en aérosol. N’utilisez qu’un chiffon
doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique
à une hauteur supérieure à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près
d’un bain, d’un lavabo, d’un évier de cuisine, d’un
bac de lavage ou d’une piscine, ou dans un sous-
sol humide ou sous la douche.
6. Ne déposez pas ce téléphone sur un chariot,
support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans
les endroits soumis à une température extrême,
à la lumière directe du soleil ou à proximité
immédiate d’autres appareils électriques ou
électroniques. Protégez votre téléphone contre
les sources d’humidité, la poussière, les vapeurs
et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et
d’ouvertures d’aération situées à l’arrière ou
en dessous. Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être obstruées en
plaçant l’appareil sur un lit, divan, tapis ou autre
surface similaires. Ne placez pas cet appareil
proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas dans
une unité murale ou un cabinet fermé qui ne
possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage de
votre maison, consultez votre marchand ou votre
fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation.
Installez cet appareil dans un endroit sécuritaire,
là où personne ne pourra trébucher sur la
ligne d’alimentation ni le cordon téléphonique
modulaire.
11. N’insérez jamais d’objets à travers les fentes et
ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou
court-circuiter des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution. N’échappez
pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne
démontez pas l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il doit être réparé.
En enlevant le couvercle, vous vous exposez à
des tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut être à
l’origine d’une électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez l’appareil
avant de procéder au nettoyage. Utilisez un
chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les
rallonges.
14. Débranchez cet appareil de la prise de courant et
communiquez avec le département de service à
la clientèle de VTech dans les cas suivants:
Lorsque le cordon d’alimentation est
endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé une source
d’humidité telle que la pluie ou l’eau.
Si le produit ne fonctionne pas normalement
en respectant les instructions de
fonctionnement. Réglez uniquement les
commandes indiquées dans le les instructions
de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer
un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé
afin de rétablir le fonctionnement normal de
l’appareil.
Si le produit a été échappé et que le socle et/
ou le combiné a été endommagé.
Si le produit affiche une nette diminution de
sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans
fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une
fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être
provoquée lorsque l’adaptateur est branché à une
prise de courant, ou lorsque le combiné est déposé
sur le socle. Ceci est un événement commun
associé à la fermeture d’un circuit électrique.
L’utilisateur ne devrait pas brancher le téléphone
à une prise de courant, et ne devrait pas déposer
le combiné chargé sur le socle, si le téléphone se
trouve à proximité d’un endroit comportant des
concentrations de gaz inflammables, moins que
la ventilation soit adéquate. Une flammèche dans
un tel endroit pourrait provoquer un incendie ou
une explosion. De tels environnements peuvent
comprendre: des endroits où l’on utilise de
l’oxygène médical sans ventilation adéquate; des
gaz industriels (dissolvants de nettoyage, des
vapeurs d’essence, etc.); une fuite de gaz naturel,
etc.
17. Ne placez que le combiné de votre téléphone près
de votre oreille lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés
en position verticale ou montés au sol. Les broches
ne sont pas conçues pour maintenir l’adaptateur
en place si celui-ci est barnché dans une prise au
plafond ou sous une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE
COURANT, le socle de prise de courant doit
etre installe a proximite du materiel et doit etre
aisement accessible.
MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de
piles pour le téléphone. N’utilisez que les piles
rechargeable inclus ou les piles de rechange
(BT162342/BT262342). N’incinérez pas les piles.
Celles-ci risqueraient d’exploser.
21. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Socle : 6 V CC @ 600 mA
Chargeur : 6 V CC @ 600 mA
CONSERVEZ CES INSTRUCTIONS
Pile
N’utilisez que la pile incluse ou l’équivalent. Pour
commander une pile de recharge, visitez notre
site Web au www.vtechphones.com ou composez
le 800-595-9511. Au Canada, visitez le phones.
vtechcanada.com ou composez le 800-267-7377.
Ne jetez pas la pile au feu. Vérifiez les instructions
spécifiques de mise aux rebus auprès des autorités
locales.
N’ouvrez pas et ne mutilez pas la pile. Lélectrolyte
qui s’en échapperait est corrosif et pourrait causer
des brûlures ou des blessures aux yeux ou à la
peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles
afin d’éviter les courts-circuits provoqués par des
matériaux conducteurs.
Rechargez la pile incluse avec cet appareil, selon
les instructions et limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique uniquement
aux téléphones numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante, a mené
une évaluation pluridisciplinaire des interférences
entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs
cardiaques
Ils doivent tenir le téléphone sans fil à une distance
d’au moins six pouces du stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un
téléphone sans fil à proximité de ceux-ci.
À propos des téléphones sans fil
Alimentation électrique: Les mêmes
caractéristiques qui constituent des avantages
pour les téléphones sans fil affichent également
des restrictions. Les appels téléphoniques sont
transmis entre le combiné sans fil et le socle par le
biais d’ondes radio ; il y a donc la possibilité que
vos conversations téléphoniques sans fil soient
interceptées par des équipements de réception
radio se trouvant dans la portée du combiné sans
fil. Pour cette raison, vous ne devez pas percevoir
les communications téléphoniques sans fil comme
étant aussi confidentielles.
Alimentation électrique: Le socle de ce téléphone
sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être
contrôlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si
le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téléviseurs:
Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interférences aux
téléviseurs et aux magnétoscopes. Pour réduire
ou prévenir de telles interférences, ne placez
pas le socle du téléphone sans fil près ou sur un
téléviseur ou magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner le téléphone
sans fil du téléviseur ou du magnétoscope afin de
réduire possiblement les interférences.
Piles rechargeables: Manipulez les piles avec soin
afin de ne pas les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le conducteur peut
surchauffer et causer des blessures. Respectez la
polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure
métallique de nickel: Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez
pas et ne les percez pas. Tel que les autres piles
de ce type, elles pourraient dégager une matière
toxique qui peut causer des blessures corporelles
si elles sont brûlées ou percées.
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery
indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful lives,
when taken out of service within the United States and
Canada.
The RBRC® program provides a convenient alternative
to placing used nickel-metal hydride batteries into
the trash or municipal waste, which may be illegal in
your area.
VTech’s participation in RBRC® makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery
recycling and disposal bans/restrictions in your area.
VTech’s involvement in this program is part of its
commitment to protecting our environment and
conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered
trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to
comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product.
This product has been tested and found to comply
with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base shall
be installed and used such that parts of the user’s body
other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC
rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this
equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service
provider upon request.
The plug and jack used to connect this equipment
to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with
this product. It is designed to be connected to a
compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to
a single line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to
determine how many devices you may connect to
your telephone line and still have them ring when
you are called. The REN for this product is encoded
as the 6th and 7th characters following the US: in the
product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be
five (5.0) or less. For more information, please contact
your telephone service provider.
This equipment may not be used with Party Lines. If
you have specially wired alarm dialing equipment
connected to your telephone line, ensure the
connection of this equipment does not disable your
alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it must be
unplugged from the modular jack until the problem
has been corrected. Replacement to this telephone
equipment can only be made by the manufacturer or
its authorized agents. For replacement procedures,
follow the instructions outlined under the “Limited
warranty”.
If this equipment is causing harm to the telephone
network, the telephone service provider may
temporarily discontinue your telephone service. The
telephone service provider is required to notify you
before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You
will be given the opportunity to correct the problem
and the telephone service provider is required to
inform you of your right to file a complaint with the
FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or
procedures that could affect the proper functioning
of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless
handset, it is hearing aid compatible.
If this product has memory dialing locations, you may
choose to store emergency telephone numbers (e.g.,
police, fire, medical) in these locations. If you do store
or test emergency numbers, please:
Remain on the line and briefly explain the reason for
the call before hanging up.
Perform such activities in off-peak hours, such as early
morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation.
Privacy of communications may not be ensured when
using this telephone.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this
terminal equipment is 1.0. The REN is an indication
of the maximum number of devices allowed to be
connected to a telephone interface. The termination
on an interface may consist of any combination of
devices subject only to the requirement that the sum
of the RENs of all the devices does not exceed five.
This product meets the applicable Innovation, Science
and Economic Development Canada technical
specifications.
Install | Set up 14
What’s in the box 14
Connect the telephone base 15
Connect the charger 15
Install the battery 15
Charge the battery 16
Check the battery level 16
Check for dial tone 17
Before use 17
Set up through voice guide - Date
and time (before use) 17
Set up through voice guide - Smart
call blocker (before use) 18
Set up through voice guide -
Answering system (before use) 18
Install 19
Mount the telephone base 19
Overview 20
Telephone base 20
Handset 21
Display 23
Handset lights 23
Operating range 24
Operate 25
Make, answer or end a cell call 25
Make a cell call 25
Predial a cell call 25
Answer a cell call 25
End a cell call 25
Make, answer, or end a home call
25
Make a home call 25
Predial a home call 25
Answer a home call 26
End a home call 26
Using a Bluetooth headset to
answer a home call 26
Answer or end a home call using a
Bluetooth headset 26
View dialing options 26
Option while on a call 27
Join a call 27
Join a call in progress 27
Intercom 27
Initiate an intercom call 27
Answer an intercom call 27
End an intercom call 28
Transfer a call via intercom 28
Sound 29
Use speakerphone 29
Mute the microphone 29
Temporary ringer silencing 29
Find handset 29
Page/ find handset 29
Use phone menu 30
Contents
Phonebook | Phonebook entry 30
Add a phonebook entry 30
Review the phonebook entries
31
Dial a phonebook entry 31
Delete a phonebook entry 31
Delete all phonebook entries 32
Edit a phonebook entry 32
Alphabetical search 32
Redial list 33
Review and dial a redial list entry 33
Delete a redial list entry 33
Call waiting 34
Call waiting on the cell line 34
Call waiting on the home line 34
Predial via home call and cell call 35
Chain dialing 35
Caller ID 36
Save a caller ID log entry to the
phonebook 36
Save a caller ID log entry to call
block list 37
Review the caller ID log 37
Dial a caller ID log entry 38
Delete caller ID log entries 38
Caller ID memory match 38
Missed call indicator 38
Bluetooth 39
Add a Bluetooth cell phone 39
Add a Bluetooth headset 40
Review the Bluetooth device list 40
Download/Transfer your cell phone
phonebook entries via Bluetooth
40
Connect / disconnect an active
Bluetooth device 41
Auto Bluetooth connection 42
Answering system 42
Difference between the built-in
answering system and voicemail
service 42
Use your built-in answering system
43
Turn on or off the answering system
44
Playback messages 44
Delete all messages 45
Answering system remote access 45
Call intercept while using answering
system 46
Recording memo 46
Turn on or off the call screening 47
Screen a call with answering system
47
Announcement 48
Record a new outgoing
announcement 48
Record your name for all screening
announcements 48
Play your announcement 48
Delete your annoucement 48
Play your current announcement
of screening with or without caller
name 49
Screening announcements 49
Reset all your screening
announcements 50
Voicemail (via Tlephone service
provider) 50
Turn off the new voicemail
indicators 50
Activate and use cell phone’s
voice app via handset/
telephone base 51
Smart call blocker 53
Turn on or off Smart call blocker
53
Allowed calls 54
Blocked calls 54
Screen unknown home calls 55
Screen robocalls 57
Screened call options 58
Block calls | Call block list 59
Add a call block entry 59
Edit a call block list entry 60
Review call block list 60
Block unknown calls 61
Unblock a telephone number
61
Configure | Settings 61
Smart call blocker settings 61
Set profile 61
Set Smart call blocker through voice
guide 62
Star name entry/ list 63
Add a star name entry 63
Delete a star name entry 64
Delete all star name entries 64
Edit a star name entry 64
Save a caller ID log entry to star
name list 65
Review star name list 65
Allow entry/ list 65
Add an allow entry 65
Delete an allow entry 66
Delete all allow entries 66
Save a caller ID log entry to allow
list 66
Edit an allow entry 67
Review allow list 67
Block entry/ list 68
Add a block entry 68
Edit a block entry 68
Contents
Delete all block list entries 69
Save a caller ID log entry to block
list 69
Review block list 70
Answering system settings 70
Set your built-in answering system
70
Set answering system through voice
guide 71
Set remote access code 71
Turn on or off the message alert
tone 72
Area code settings 72
Set home area code 72
Dial modes 73
Temporary tone dialing 73
Set dial mode 73
Ringer 73
Set ringer tone 73
Adjust and turn off the ringer
volume 74
Set date and time 74
Set languages 75
Set LCD language 75
Sound settings 75
Set number of rings 75
Set QUIET mode 76
Set listening volume 76
Set key tone 76
Voicemail settings 77
Set speed dial voicemail number 77
Add and register handset 77
General product care 78
Taking care of your telephone 78
Avoid rough treatment 78
Avoid water 78
Electrical storms 78
Cleaning your telephone 78
Technical specifications 79
DECT 6.0 digital technology 79
Telephone operating range 79
Redefining long range coverage
and clarity 79
Simulated full-duplex handset
and base speakerphones 80
Frequently asked questions 80
14
Install | Set up
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in case it is
necessary to ship your telephone for
warranty service.
You can add new handsets (VS112-17/
VS112-27/VS112-37/VS112-47) to your
telephone system. All accessories are
sold separately. Your telephone base
supports a maximum of five devices
NOTE
To purchase replacement batteries or
power adapters, visit our website at
www.vtechphones.com or call 1 (800)
595-9511. In Canada, go to phones.
vtechcanada.com or dial 1 (800) 267-
7377.
Quick
start
guide
Introducing
Smart call
blocker
1 set for
VS112/
VS112-17
2 sets for
VS112-2/
VS112-27
3 sets for
VS112-3/
VS112-37
4 sets for
VS112-4/
VS112-47
1 set for
VS112-2/
VS112-27
2 sets for
VS112-3/
VS112-37
3 sets for
VS112-4/
VS112-47
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1951
15
Connect the telephone base
TIPS
If you want to mount the base, make
sure telephone line pass through the
mounting bracket before connecting
to the DSL filter.
If you subscribe to digital subscriber
line (DSL) high-speed Internet
service through your telephone line,
make sure you connect a DSL filter
(not included) to the telephone wall
jack.
Connect the charger
Install the battery
1. Plug the battery connector securely
into the socket inside the handset
battery compartiment.
Make sure the battery label THIS
SIDE UP is facing up, as indicated.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1951
THIS SIDE UP
12 hrs
16
2. Align the cover flat against the battery
compartment, then slide it upwards
until it clicks into place.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1951
Charge the battery
The following table summarizes th
battery indicators and actions to take.
Battery
indicators
Battery
status
Action
The screen
is blank, or
shows Put in
charger and
flashes.
The battery
has no
charge or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(at least 30
minutes).
The screen
shows Low
battery and
flashes.
The battery
has enough
charge to be
used for a
short time.
Charge
without
interruption
(at least 30
minutes).
The screen
shows
HANDSET X.
The battery is
charged.
To keep
the battery
charged,
place it in
the handset
charger
when not in
use.
When it is fully charged, you can expect
the following performance:
Operation Operating time *
Talk time (cordless
handset)
10 hours
Talk time
(cordless handset
speakerphone)
4.5 hours
Standby 5 days
* Operating times vary depending on
your actual use and the age of the battery.
Check the battery level
After you have installed the battery,
check the battery level on the handset
screen.
If the screen is blank, or flashes,
then the battery needs to be
charged. Go to Charge the battery
section before you do any setting or
operation.
If the battery icon is , , or , then
go to Set the date and time and Set
the answering system and Smart call
blocker through voice guide section.
17
Check for dial tone
Press . If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone
Make sure the installation
procedures are properly done.
The handset may take a second or
two to find the telephone base and
produce a dial tone. This is normal.
Wait an extra second before dialing.
If the previous suggestions do not
work, disconnect the telephone
line cord from your telephone and
connect the telephone line cord to
another telephone.
If there is no dial tone on that other
telephone either, your telephone
line cord may be defective. Install a
new telephone line cord.
If changing the telephone line
cord does not help, the wall jack
(or the wiring to this wall jack) may
be defective. Try using a different
wall jack in your home to connect
your VS112, VS112-2, VS112-3, VS112-
4, VS112-17, VS112-27, VS112-37,
VS112-47 telephone, or contact your
telephone service provider (charges
may apply).
Before use
Set up through voice guide - Date and
time (before use)
After you install your telephone or
power returns following a power outage
and battery depletion, the handset will
prompt you to set the date and time,
and to configure the Smart call blocker
and answering system through voice
guide.
NOTE
Make sure you set the date and
time including the year correctly;
otherwise the answering system
does not announce the correct
day of the week for your recorded
messages time stamp.
1. Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then, press SELECT.
2. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press p/q to choose AM or PM.
3. Press SELECT to save.
After setting the date and time, the
handset will prompt if you want to set
Smart call blocker (before use).
TIP
To skip setting the date and time,
press on the handset.
18
Set up through voice guide - Smart call
blocker (before use)
After the date and time setting is done
or skipped, the handset will prompt if
you want to set Smart call blocker. Press
MENU/SELECT to start the Smart call
blocker setup via voice guide.
This feature is an easy and alternative way
for you to do the basic setup of Smart call
blocker. You can follow the voice guide
to set your telephone system to allow or
to screen all incoming home calls, or to
screen home calls that do not display a
phone number.
You hear a voice prompt “Hello! This
voice guide will assist you with the basic
setup of Smart call blocker...
Set up your Smart call blocker feature by
inputting the designated numbers, as
instructed in the voice guide.
Press 1 if you want to screen home
calls with telephone numbers that are
not saved in your directory, allow list
or star name list; or
Press 2 if you do not want to screen
calls, and want to allow all incoming
calls to get through.
NOTES
The screening feature of Smart call
blocker is applicable to home calls
only. All incoming cell calls will get
through and ring. If you want to block
a cell call, add the number to the block
list. See Block List.
You can press on the telephone
base to quit the voice guide at any
time.
Set up through voice guide - Answering
system (before use)
After the Smart call blocker setting is done
or skipped, the handset will then prompt
if you want to set up the answering
system. Press MENU/SELECT to start the
answering system setup via voice guide.
To skip the set up, press .
You can record your own announcement,
set the number of rings, and set the
message alert tone.
1. Press MENU/SELECT on the handset
(for VS112) in idle mode.
2. Press p/q to highlight Answering
sys, then press MENU/SELECT.
3. Press p/q to highlight Voice guide,
then press MENU/SELECT. You hear
a voice prompt, “This voice guide will
assist you with the basic setup of your
answering system.
4. Set up your answering system by
inputting designated numbers, as
instructed in the voice guide.
You can press on the telephone
base to quit the voice guide at any
time.
19
Install
Mount the telephone base
Your telephone base is ready for tabletop
use. If you want to mount your telephone
on a wall, use the provided wall-mount
bracket to attach to a standard dual-stud
telephone wall-mounting plate.
If you do not have this wall-mounting
plate, you can purchase one from many
hardware or consumer electronics
retailers. You may need a professional to
install the wall-mounting plate.
1.
2.
3.
4.
20
Overview
Telephone base
1LCD light
indicator
ANS ON/OFF
On when the built-in
answering system is
on.
IN USE
On when the phone
is in use, or when the
answering system is
answering a call.
On when a handset is
being registered.
Flashes when there is
an incoming call.
Flashes when
handsets are being
deregistered.
Flashes when another
telephone on the
same line is in use.
/
On when a device is
successfully paired
and connected.
2
X/DELETE
Press to delete the
message currently
playing.
When the phone is
not in use, press twice
to delete all previously
reviewed messages.
While reviewing the
redial list, phonebook,
caller ID log, allow list,
block list, or star name
list, press to delete
an individual entry.
While entering names
or numbers, press
to delete a digit or a
character.
While predialing,
press to delete a digits.
/REPEAT
Press to repeat a
message or press
twice to play the
previous message.
/SKIP
During message
playback, press to skip
to the next message.
/PLAY/STOP
Press to play messages.
Press to stop message
playback.
3 ANS
ON/OFF
Press to turn on the
answering system and
press again to turn off.
The light is on when on
the answering system is
on.
4
Press to turn on the
Bluetooth feature and
search or add new
devices.
5- VOL +
Press to adjust the
listening volume during
a call.
When the phone is not
in use, press to adjust the
telephone base ringer
volume for all lines.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

VTech VS112-17 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues