PST16 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the PST16 does not exceed
200 lbs (90.7 kg). Use with products heavier than the
maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
DIMENSIONS
2.00
50.8
.34
8.6
18.38
466.7
19.50
17.00
431.8
.69
17.5
2.06
C/L OF TOP
MOUNTING
BUTTONS
52.4
16.00
406.4
1.75
44.5
FLAG EXTENDERS FOR
LARGER SCREENS
1.32
33.4
MEASUREMENTS: [MILLIMETERS]
INCHES
Installation Instructions PST16
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PST16 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32"
1/2"
3/8"
A (1)
[PST16]
C (2)
10-24 x 1/2"
D (2)
10-24
E (4)
5/16 x 2-1/2"
F (4)
5/16"
B (2)
[Flag extender]
Installation Instructions PST16
5
ASSEMBLY AND INSTALLATION
NOTE: The PST16 may be mounted to a wood 2" x 4" stud
wall, 16" on center. The PST16 has a lateral shift of 1"
after attachment to stud wall.
IMPORTANT ! : If the installation of this product requires
OSHPD seismic approval, refer to the OSHPD pre-
approval documents and drawings before beginning
installation. OSHPD documents and drawings are
available at www.chiefmfg.com, and located on the PST16
product information page.
Mount Assembly (Optional)
1. Insert flag extender (B) slot into top of right latching flag.
2. Attach using one 10-24 x 1/2" Phillips undercut machine
screw (C) and one 10-24 nylon locknut (D). (See Figure 1)
3. Repeat with left latching flag. (See Figure 1)
Figure 1
Mount Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s
responsibility to make sure the structure to which this
component is attached can support five times the combined
weight of all equipment. Reinforce the structure as required
before installing the component.
1. Identify a suitable wall location for the PST16 taking into
consideration the display size.
2. Using a stud finder, locate and mark the two studs to which
the PST16 will be installed.
3. Use a nail as a temporary mount and hang the PST16 on
the wall using the triangular hole in the center of the PST16.
(See Figure 2)
4. Level the PST16 and mark the four mounting holes. (See
Figure 2)
5. Remove the PST16 from the wall.
Figure 2
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
6. Using a 7/32" drill bit, drill four 2-1/2" deep pilot holes,
ensuring they are centered on the studs. (See Figure 3)
7. Fasten PST16 to wall using four 5/16 x 2-1/2" lag bolts (E)
and four 5/16" flat washers (F). (See Figure 3)
2
(C) x 1
(D)
(B)
1
Flag extender slot
4
3
x 4
PST16 Installation Instructions
6
Figure 3
Display Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT install display in a
manner other than that specified by the manufacturer. Certain
displays may require the use of an interface bracket for
proper installation of the display. If an interface bracket is not
installed or there are any questions regarding which interface
bracket should be used, immediately contact a Chief
Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
1. Install Listed interface bracket (not included) following the
installation instructions provided with the interface bracket.
2. Move two latching flags on PST16 to the OPEN position.
(See Figure 4)
Figure 4
3. Align mounting buttons on display with teardrop mounting
holes in mount. (See Figure 5)
4. Move display forward until recessed area of mounting
buttons is positioned over lower area of teardrop mounting
holes. (See Figure 5)
5. Lower display until recessed area of mounting buttons is
seated in lower area of teardrop mounting holes.
(See Figure 5)
Figure 5
6. Move two latching flags on PST16 to the CLOSED position.
(See Figure 6)
7
6
(E) x 4
(F) x 4
x 4
[7/32" x 2-1/2"]
2
OPEN
Latching flag
Display
3
4
5
Installation Instructions PST16
7
Figure 6
7. OPTIONAL: Lock the latching flags with a padlock or bolt, if
required. (See Figure 7)
Figure 7
8. Route wires and cables to display.
6
CLOSED
Latching flag
Place lock or
bolt here to lock
latching flag
7
PST16 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8805-002006 Rev02
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
08/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Chief PST16 User manual
Documents connexes
-
Chief MTSAVB Guide d'installation
-
Chief PACCS1 Guide d'installation
-
-
-
-
-
Chief PDC2306 Guide d'installation
-
Chief Manufacturing PCS2051 Manuel utilisateur
-
-