Asus RP-AX56 Manuel utilisateur

Marque: Asus

Modèle: RP-AX56

Taper: Manuel utilisateur

Placing your RP-AX56

Plug your RP-AX56 into a power outlet near

your router/AP.

Check the LEDs and see the LED explanations.

METHOD 1Download the ASUS

Extender App

METHOD 2Connect via WPS

Press the WPS button on your router/

A P.

Press the WPS button on your

RP-AX56 for more than two (2)

seconds until the LED starts to

blink blue.

RP-AX56

Dual-Band Wireless Repeater

Quick

Start Guide

Hardware Explanations

Button Explanations

RESET BUTTON

Reset the system to its factory default settings.

WPS BUTTON

Launch the WPS Wizard.

LAN PORT

Connect your PC to the LAN port with a network cable.

BEFORE SETUP

SETUP METHODS

WE SUGGEST…

Set up RP-AX56 as a repeater

Plug RP-AX56 into a power outlet.

The LED will start breathing white for 3 seconds while booting

up.

LAN port

LED

WPS button

reset button

LED Explanations

Repeater Mode

Status LED Behavior

Booting up Blinking White

Booting up complete (haven’t

connected to Router) Solid Blue

Reset (use a pin to press the

reset button for 5 seconds) Blinking Yellow

Rescue mode Solid Purple

Starting WPS Blinking Blue

Connected to the router with

Good Signal Solid White

Conneccted to the router with

Weak Signal Solid Yellow

No Signal Solid Red

AP mode (with wired

connection) Solid White

AP mode (without wired

connection) Solid Red

AiMesh Mode

Status LED Behavior

Booting up Blinking White

Booting up complete (not

connected to AiMesh Router) Solid Blue

Reset (use a pin to press the

reset button for 5 seconds) Blinking Yellow

Rescue mode Solid Purple

Connecting to the AiMesh Router Blinking Blue

Connected to the AiMesh Router

with Good Signal Solid White

Connected to the AiMesh Router

with Weak Signal Solid Yellow

No Signal Solid Red

Ethernet backhaul Solid White

Wait for the LED to ﬂash and turn solid blue,

indicating that your RP-AX56 is ready to connect

to your existing router/AP.

around

2 meters

If you would like to connect RP-AX56 to other WiFi networks excluding AiMesh-supported routers, please download the

ASUS Extender App.

1 2

If your AiMesh router cannot find RP-AX56 nearby or

synchronization fails, please check followings and try again.

Download AiMesh - supported ﬁreware at:

https://www.asus.com/AiMesh/.

ii.

Launch a web GUI. You will be redirected to the

ASUS Setup Wizard. If not, navigate to http://router.

asus.com.

iii.

Go to Administration > Firmware Upgrade. Click

Choose File, and upload the AiMesh-supported

ﬁrmware.

iv. After the ﬁrmware is uploaded, please go to the

Network Map page to check and make sure that the

AiMesh icon shows up.

v. Use a pin to press the reset button on your RP-AX56

for at least 5 seconds. Release the reset button when

the power LED is ﬂashing slowly.

優優優優

A: Yes. AiMesh system supports both wireless

and wired connection between an AiMesh router

and node to maximize throughput and stability.

AiMesh analyzes the wireless signal strength

for each frequency band available, and then

determines automatically whether a wireless or

wired connection is best to serve as the inter-router

connection backbone.

To know more about ASUS AiMesh, please go to https://www.asus.com/AiMesh/.

RELOCATION

FAQ

TROUBLE SHOOTING

THE BEST PERFORMANCE

FREQUENTLY ASKED QUESTIONS

Plug RP-AX56 into a power outlet near your

router/AP. Ensure that it is within 3 meters from

the AiMesh router.

Your AiMesh router is upgraded to AiMesh-

supported ﬁrmware.

Locate the AiMesh router and RP-AX56 at best place.

NOTES: • To minimize interference, keep the routers away from devices like cordless phones, Bluetooth devices and

microwave ovens.

• We recommend that you place the routers in an open or spacious location.

Could I setup wired connection between AiMesh routers and nodes (Ethernet

backhaul)?

1 Follow the setup steps to establish a connection

between the AiMesh router and RP-AX56 via WiFi ﬁrst.

2 Place the RP-AX56 in an ideal location for the best

coverage. Run an Ethernet cable from the LAN port of

the AiMesh router to the Ethernet backhaul port of RP-

AX56.

3 AiMesh system will auto-select the best

path for data transmission, whether wired

or wireless.

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest

standards for protecting our environment. We believe in providing solutions for you to

be able to responsibly recycle our products, batteries, other components, as well as the

packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed

recycling information in dierent regions.

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of

Chemicals) regulatory framework, we published the chemical substances in our products at

ASUS REACH website at http://csr.asus.com/english/REACH.htm

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital de-

vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

WARNING! Any changes or modications not expressly approved by the

party responsible for compliance could void the user’s authority to operate

the equipment.

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating in conjunction with any

other antenna or transmitter.

IMPORTANT NOTE:

Radiation Exposure Statement: This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. End users must follow the specic

operating instructions for satisfying RF exposure compliance. To maintain compliance with

FCC exposure compliance requirement, please follow operation instruction as documented

in this manual.

WARNING! This equipment must be installed and operated in accordance

with provided instructions and the antenna(s) used for this transmitter must

be installed to provide a separation distance of at least 20 cm from all persons

and must not be co-located or operating in conjunction with any other

antenna or transmitter.

Compliance Statement of Innovation, Science and Economic

Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for

harmful interference to co-channel mobile satellite systems.

CAN ICES-3(B)/NMB-3(B)

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below the Innovation, Science

and Economic Development Canada radio frequency exposure limits. The ASUS Wireless

Device should be used in such a manner such that the potential for human contact during

normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 20 cm

between the radiator any part of your body.

This device has been certied for use in Canada. Status of the listing in the Innovation,

Science and Economic Development Canada’s REL (Radio Equipment List) can be found at

the following web address: http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure also can be found at the following web:

https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Déclaration de conformité de Innovation, Sciences et Développement

économique Canada (ISED)

Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

La bande 5150 – 5250 MHz est réservée uniquement pour une utilisation à l’intérieur an de

réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant

les mêmes canaux.

CAN ICES-3(B)/NMB-3(B)

Informations concernant l’exposition aux fréquences radio (RF)

La puissance de sortie émise par cet appareil sans l est inférieure à la limite d'exposition

aux fréquences radio d'Innovation, Sciences et Développement économique du Canada

(ISED). Utilisez l'appareil sans l de façon à minimiser les contacts humains lors d'un

fonctionnement normal.

Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la

source de rayonnement et votre corps.

L'utilisation de cet appareil est autorisée au Canada. Pour consulter l'entrée correspondant

à l'appareil dans la liste d'équipement radio (REL - Radio Equipment List) d'Innovation,

Sciences et Développement économique du Canada, rendez-vous sur :

http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Pour des informations supplémentaires concernant l'exposition aux fréquences radio au

Canada, rendez-vous sur : https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

For product available in the US/Canada market, only channel 1~11 can be operated. Selec-

tion of other channels is not possible.

Pour les produits disponibles aux États-Unis et au Canada, seuls les canaux 1 à 11 peuvent

être utilisés. La sélection d’autres canaux n’est pas possible.

Safety Notices

• Use this product in environments with ambient temperatures between 0°C(32°F) and

40°C(104°F).

• Refer to the rating label on the bottom of your product and ensure your power adapter

complies with this rating.

• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has

been damaged.

• DO NOT place or drop objects on top and do not shove any foreign objects into the

product.

• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during

electrical storms.

• DO NOT cover the vents on the product to prevent the system from getting overheated.

• DO NOT use damaged power cords, accessories, or other peripherals.

• If the Adapter is broken, do not try to x it by yourself. Contact a qualied service techni-

cian or your retailer.

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

LAN to LAN (Ethernet backhaul) port

METHOD Download the ASUS Router App

If you already have an AiMesh router and you are going to create an AiMesh system, please download and install ASUS

Router App for RP-AX56 setup. Please select RP-AX56 as the AiMesh Node.

SETUP METHODS Set up RP-AX56 as an AiMesh Node

Q2 How to set up the Access Point(AP) mode on an ASUS Repeater?

1 Launch a web browser and enter http://repeater.asus.

com.

2 If you are logging into the Web GUI for the ﬁrst time,

you will be automatically directed to the Quick Internet

Setup (QIS) page. Click Advanced Settings.

3 Click Choose operation mode, then click

Access Point(AP) mode.

4 Click Automatic IP, then click to set up

the SSIDs separately.

5 For the ﬁrst time, you’ll need to set up

the username and password for your RP-

AX56. When typing is done, click Next.

Access Point(AP) mode setting is ﬁnished.

Asus RP-AX56 Manuel utilisateur

Marque: Asus

Modèle: RP-AX56

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Asus RP-AX56 User manual

Asus RP-AX56 Manuel utilisateur

Asus RP-AX56 Manuel utilisateur

dans d''autres langues

Documents connexes