Snom M58 Guide d'installation
- Catégorie
- Téléphones
- Taper
- Guide d'installation
Ce manuel convient également à
M58
SIP DECT Deskset
Quick Installation Guide
2
Important Safety Information
This symbol is to alert you to important operating or servicing
instructions that may appear on the product or in this user’s manual.
Always follow basic safety precautions when using this product to
reduce the risk of injury, fire, or electric shock.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1. This product should be installed by a qualified technician.
2. This product should only be connected to the host equipment and never
directly to the network such as Public Switch Telephone Network (PSTN) or
Plain Old Telephone Services (POTS).
3. Read and understand all instructions.
4. Follow all warnings and instructions marked on the product.
5. Unplug this product from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
6. Do not use this product near water such as near a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
7. Do not place this product on an unstable table, shelf, stand or other
unstable surfaces.
8. Slots and openings in the back or bottom of the handset are provided for
ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug.
This product should never be placed near or over a radiator or heat register.
This product should not be placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supplied at the premises, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not install this product
where the cord may be walked on.
11. Never push objects of any kind into this product through the slots in the
handset because they may touch dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the product.
3
12. To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing parts of the
handset other than specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer servicing to an
authorized service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized
technician to restore the product to normal operation.
E. If the product has been dropped and the telephone base and/or
handset has been damaged.
F. If the product exhibits a distinct change in performance.
15. Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the vicinity of the leak.
Under certain circumstances, a spark may be created when the adapter is
plugged into the power outlet, or when the handset is replaced in its cradle.
This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put
a charged handset into the cradle, if the phone is located in an environment
containing concentrations of flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in such an environment could create
a fire or explosion. Such environments might include: medical use of oxygen
without adequate ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear when it is in normal
talk mode.
18. The power adapters are intended to be correctly oriented in a vertical or
floor mount position. The prongs are not designed to hold the plug in place if
it is plugged into a ceiling, under-the-table or cabinet outlet.
4
19. Use only the power cord indicated in this manual.
20. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
21. CAUTION: Keep small metallic objects such as pins and staples away from
the handset receiver.
22. WARNING: The product included (ITE) in this manual is to be connected only
to PoE networks without routing to the outside plant.
SAVE THESE INSTRUCTIONS
Power requirements
Power adapter: VT05EUS05100
Input: 100~240V AC 50/60Hz 0.15A
Output: 5.0 V DC @ 1A
For cUL compliance only
Mesures de sécurité importantes
Ce symbole vous alertera d’informations importantes ou
d’instructions d’entretien pouvant apparaître dans ce guide
d’utilisation. Respectez toujours les mesures de sécurité et de
sécurité de base lorsque vous utilisez ce produit, afin de réduire les
risques de blessures, d’incendie, ou d’électrocution.
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou
d’électrocution, suivez toujours ces mesures préventives de base lorsque vous
utilisez votre téléphone
1. Cet appareil doit être installé par un technicien qualifié.
2. Cet appareil doit être branché à un équipement hôte et jamais branché à un
réseau, tel qu’un réseau PSTN publique ou un réseau téléphonique standard
(POTS).
3. Lisez et comprenez bien toutes les instructions.
4. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
5. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et
légèrement humecté.
6. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo,
5
d’un évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-
sol humide ou sous la douche.
7. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.
L’appareil pourrait tomber et être sérieusement endommagé.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées
à l’arrière ou en dessous. Afin d’empêcher la surchauffe, ces ouvertures
ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis
ou autre surface similaires. Ne placez pas cet appareil à proximité d’un
élément de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas
dans une unité murale ou un cabinet fermé qui ne possède pas d’aération
adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur
les étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre
maison, consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans
un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne
d’alimentation ni le cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet
appareil, car ils pourraient toucher à des points de tension dangereux ou
court-circuiter des pièces, ce qui constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service qualifié s’il doit être réparé. En
enlevant le couvercle, vous vous exposez à des tensions dangereuses ou
autres dangers similaires. Un remontage inadéquat peut être à l’origine
d’une électrocution lors d’une utilisation ultérieure de l’appareil.
13. Ne surchargez pas les prises de courant ni les rallonges électriques, car
ceci peut constituer un risque d’incendie ou d’électrocution.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de Snom dans les cas suivants:
A. Lorsque le cordon d’alimentation est endommagé ou écorché.
B. Si du liquide a été échappé dans l’appareil.
C.
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou
l’eau.
D. Si l’appareil ne fonctionne pas normalement en suivant les directives
du guide. N’ajustez que les commandes couvertes dans le guide
d’utilisation, car un mauvais réglage de celles-ci peut être à l’origine
6
de dommages, ce qui nécessiterait des réparations considérables pour
remettre l’appareil à son état de fonctionnement normal.
E. Si l’appareil a été échappé ou son boîtier, endommagé.
F. Si le produit affiche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de
celle-ci. Sous certaines circonstances, une inteincelle pourrait survenir
lorsque l’adaptateur est branché à une prise de courant, ou lorsque le
combiné est déposé sur le combiné. Ceci est un événement commun
associé avec la fermeture d’un circuit électrique. L’utilisateur ne devrait
pas brancher le téléphone dans une prise de courant, et ne devrait pas
déposer le combiné chargé sur le socle, si le téléphone se trouve dans un
environnement ou la concentration de gaz inflammables, sans ventilation
adéquate. Une étincelle dans ces endroits pourrait provoquer un incendie ou
une explosion. Ces environnements pourraient être l’utilisation médicale de
l’oxygène sans ventilation adéquate; le gaz industriel (dissolvants, vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
17. Placez uniquement le combiné de votre appareil près de votre oreille
lorsqu’il est en mode de conversation normal.
18. Les adaptateurs sont conçus pour être orientés en position verticale ou en
position horizontale sur le plancher.
19. N’utilisez que cordon d’alimentation et les piles indiquées dans ce guide
d’utilisation.
20. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de
courant doit être installée près du produit, afin d’assurer une accessibilité
sécuritaire à la prise de courant.
21. MISE EN GARDE : Éloignez les petits objets métalliques tels que les broches
de l’écouteur du combiné.
22. AVERTISSEMENT : Le produit inclus (ITE) dans ce guide doit être connecté
uniquement aux réseaux PoE sans être acheminé vers l’installation
extérieure.
CONSERVEZ CES INSTRUCTIONS
Alimentation électrique
Adaptateur électrique : VT05EUS05100
Entrée : 100~240V AC 50/60Hz 0.15A
Sortie : 5.0 V DC @ 1A
7
Compliance
FCC part 15
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
the user’s expense.
Privacy of communications may not be ensured when using this phone.
Warning: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Part 68
Consumer Information:
a. This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the back or bottom of this equipment is a label
that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the
telephone company.
b. An applicable certification jacks Universal Service Order Codes (USOC) for
the equipment is provided (i.e., RJ45C) in the packaging with each piece of
approved terminal equipment.
c. A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant LAN cable (RJ45) and modular
plug is provided with this product. An RJ45 jack should normally be used for
Caution: To maintain the compliance with the FCC’s/ISEDC’s RF exposure
guideline, place the base unit at least 20 cm from nearby persons.
8
Compliance
connecting to the SIP equipment through the LAN cable. See installation
instructions for details.
d. If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is
necessary.
e. The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If this happens the telephone company will provide advance notice in order
for you to make necessary modifications to maintain uninterrupted service.
f. Should you experience trouble with this equipment, please contact
Snom Technology GmbH
1 (339) 227-6160 (select option 2)
for repair or warranty information. If the equipment is causing harm to
the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
g. Please follow instructions for repairing if any (e.g. battery replacement
section); otherwise do not alternate or repair any parts of device except
specified.
h. Connection to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or corporation
commission for information.
i. NOTICE: If you have specially wired alarm equipment connected to the
telephone line, ensure the installation of this product does not disable your
alarm equipment.
If you have questions about what will disable alarm equipment, consult your
telephone company or a qualified installer.
j. This equipment is hearing aid compatible.
NOTICE: According to telephone company reports, AC electrical surges, typically
resulting from lightning strikes, are very destructive to telephone equipment
connected to AC power sources. To minimize damage from these types of
surges, a surge arrestor is recommended.
9
Compliance
Industry Canada
This Class A digital apparatus complies with Canadian requirements:
CAN ICES-3 (A)/NMB-3(A). Cet appareil numérique de la classe A est conforme
à la norme CAN ICES-3 (A)/NMB-3(A) du Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
This product meets the applicable Innovation, Science and Economic
Development Canada technical specifications.
10
Parts Checklist
Your telephone package contains the following items. Save your sales receipt
and original packaging in the event warranty service is necessary.
About this Guide
This quick installation guide provides a reference for the external features of the
M58 SIP DECT Deskset and installation instructions.
The M18 SIP DECT Deskset is for use with the M500 Multi-cell SIP DECT Base
Station. Please refer to the M58 SIP DECT Deskset User Manual for complete
operation instructions.
For customer service or product information, visit our website at
www.snomamericas.com .
Power adapter
Deskset base
Deskset stand
Handset and handset cord
Quick start guide
M58
Quick
Installation
Guide
11
Quick Reference Guide
10
6
9
13
11
20
11
12
14
15
16
17
18
19
8
7
2
3
4
5
21
11 Color screen
12 Alphanumeric keypad
13 Message waiting indicator
14 Next page key
15 Cancel key
16 Message key
17 Directory key
18 Redial key
19 Call History key
20 Headset key
21 Speaker key
1 Function keys
2 Soft keys
3 Navigation keys and
center button
4 Setting key
5 OK key
6 Transfer key
7 Intercom key
8 Hold key
9 Mute key
10 Volume key
12
Deskset Installation
This section assumes that your network infrastructure is established and that your
IP PBX phone service has been ordered and configured for your location.
Deskset installation involves both the backup battery and the deskset. The deskset
is powered using the supplied power adapter. The deskset can be placed on a flat
surface.
Avoid placing the deskset too close to:
• Communication devices such as television sets, DVD players, or other cordless
telephones
• Excessive heat sources
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting
• Excessive dust sources such as a workshop or garage
• Excessive moisture
• Extremely low temperature
• Mechanical vibration or shock such as on top of a washing machine or work
bench
13
Attaching the footstand
1
2 3
14
Connecting the phone
(1, 2)
IMPORTANT INFORMATION
1. Use only the power adapter supplied with this product. To order a replacement
power adapter, visit our website at www.snomamericas.com .
2. The power adapter is intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.
15
Registering the deskset to the base station
The deskset must be registered to the base station in order to make and receive
calls.
There are three methods of registration:
• Auto registration
• Manual registation (triggered via Web UI).
• Manual registation (triggered via LINK button on base).
Registering the deskset - Auto registration
1. Make sure the base station is connected to power and the network.
2. Press the Setting key OR the User Settings function key.
The User Settings screen appears.
3. Press or to scroll down to Registration and press OK.
The Registration screen appears.
4. With This device selected, press OK.
The “This device” screen appears.
5. Press or to scroll down to Auto Registration and press OK.
The deskset displays:
Trying to auto-register...
Keep the deskset within base’s range.
If registration is successful:
The deskset beeps and displays “Deskset X Registered” .
If registration fails:
The deskset displays “Registration failed”. Press OK.
The deskset displays “Consult the phone administrator to provision the
device IPEI to the base.” Press IPEI to display the phone’s IPEI and serial
number. Give these numbers to your phone administrator.
16
Registering the deskset - Manual registration (triggered via Web UI)
1. Make sure the base station is connected to power and the network.
2. Press the Setting key OR the User Settings function key.
The User Settings screen appears.
3. Press or to scroll down to Registration and press OK.
The Registration screen appears.
4. With This device selected, press OK.
The “This device” screen appears.
5. Press or to scroll down to The base Web UI and press OK.
The deskset displays:
Login to the base’s WebUI using a browser,
Click Status, then Registration
Then, press the # key at the deskset.
Keep the deskset within base’ range
6. Open the phone’s Web UI in a web browser.
7. On the Web UI, click Status and then click Registration.
8. Press the # key on the deskset to begin registration.
The deskset displays “Registering... Please Wait.”
9. If you are promted to enter a PIN, enter the PIN and then press OK.
The default PIN is 0000.
If registration is successful:
The deskset beeps and displays “Deskset X Registered” .
If registration fails:
The deskset displays “Registration failed”. Press OK.
• If the deskset displays “Device not registered to base station.”,
press Reg. Place the deskset in the charger again for a few seconds,
remove it and try the registration steps again.
• If the deskset displays “Out of range. Searching for base...”, move the
deskset closer to the base, and try the registration steps again.
• If the deskset displays the idle screen, it means the deskset was
already registered to another base. To register the deskset to a different
base, try the registration steps again.
17
Registering the deskset - Manual registration (triggered via LINK button on base)
1. Make sure the base station is connected to power and the network.
2. Press the Setting key OR the User Settings function key.
The User Settings screen appears.
3. Press or to scroll down to Registration and press OK.
The Registration screen appears.
4. With This device selected, press OK.
The “This device” screen appears.
5. With The base LINK key selected, press OK.
The handet displays:
Press and hold the LINK key
at base for 4 seconds
Then, press the # key at the deskset.
6. Press and hold the LINK button on the base station for four seconds.
The (power) and (SIP) LEDs flash green.
7. Press the # key on the deskset to begin registration.
The deskset briefly displays “Press the WPS button on your Hub .
The deskset displays “Registering... Please Wait.”
8. If you are promted to enter a PIN, enter the PIN and then press OK.
The default PIN is 0000.
If registration is successful:
The deskset beeps and displays “Deskset X Registered” .
If registration fails:
The deskset displays “Registration failed”. Press OK.
• If the deskset displays “Device not registered to base station.”,
press Reg. Place the deskset in the charger again for a few seconds,
remove it and try the registration steps again.
• If the deskset displays “Out of range. Searching for base...”, move the
deskset closer to the base, and try the registration steps again.
• If the deskset displays the idle screen, it means the deskset was
already registered to another base. To register the deskset to a different
base, try the registration steps again.
18
Deregistering the deskset
Before using the deskset with a different base station, you must deregister the
deskset from the base station to which it is currently registered.
To deregister the deskset:
1. Press the Setting key OR the User Settings function key.
The User Settings screen appears.
2. Press or to scroll down to Registration and press OK.
The Registration screen appears.
3. Press or to scroll down to Deregistration and press OK.
The “Dereg. HS” screen appears, showing the list of registered handsets.
Your handset is indicated by ÛÛ.
4. Press or to select the handset you want to deregister, and press SELECT.
5. Enter the PIN and press OK to begin deregistration. The default PIN is 0000.
The message “Handset is deregistered” appears and the phone beeps.
Screen icons
The following screen icons indicate your phone’s current status:
Icon Status
Indicates signal strength, from one bar (weak) to
four bars (strong). Flashes when out of range.
The ringer is off.
Headset—audio is coming through a headset after
the HEADSET key was pressed.
Speakerphone—the speakerphone is active.
Microphone is muted.
Call Forward is on.
Do Not Disturb is on.
Silent mode is on.
19
Maintenance
Taking care of your telephone
• Your base station and cordless deskset contain sophisticated electronic parts,
so you must treat them with care.
• Avoid rough treatment.
• Place the handset down gently.
• Save the original packing materials to protect your products if you ever need
to ship them.
Avoid water
• You can damage your cordless telephone if it gets wet. Do not use the handset
in the rain, or handle it with wet hands. Do not install the base station and
deskset near a sink, bathtub or shower.
Electrical storms
• Electrical storms can sometimes cause power surges harmful to electronic
equipment. For your own safety, take caution when using electric appliances
during storms.
Cleaning your telephone
• Your products have a durable plastic casing that should retain its luster for
many years. Clean it only with a soft cloth slightly dampened with water or a
mild soap.
• Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you
are wet or standing in water. If the telephone base should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD FROM THE WALL, then pull
the unit out by the unplugged cord.
Technical Specifications
RF frequency band 1921.536–1928.448 MHz
Channels 5
Operating temperature 32–104 °F (0–40 °C)
Power requirements
Power adapter: VT05EUS05100
Input: 100~240V AC 50/60Hz 0.15A
Output: 5.0 V DC @ 1A
Connectors Two RJ9-4P4C (handset, headset)
Bluetooth range Up to 10m
VTECH COMMUNICATIONS, INC.
Tigard, Oregon 97223, USA.
Copyright © 2022 Snom Technology GmbH. All Rights Reserved.
v20220525 Version 2, 05/22
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Snom M58 Guide d'installation
- Catégorie
- Téléphones
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
- English: Snom M58 Installation guide