Danby DPA140HB1BDB-6 Le manuel du propriétaire

Taper
Le manuel du propriétaire
DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9
DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840
OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
MANUAL DEL PROPIETARIO
www.Danby.com
MODEL MODÈLE MODELO
DPA140HB1BDB-6
2019.10.31
PORTABLE AIR CONDITIONER
Owner’s Manual.............................1 - 14
CLIMATISEUR PORTABLE
Manuel du propriétaire.................15 - 28
AIRE ACONDICIONADO PORTÁTIL
Manual del propietario.................29 - 42
Welcome
Welcome to the Danby family. We are proud of our quality products and we believe in
dependable service. We suggest that you read this owner’s manual before plugging in your new
appliance as it contains important operation information, safety information, troubleshooting and
maintenance tips to ensure the reliability and longevity of your appliance.
Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance
call 1-800-263-2629.
Note the information below; you will need this information to obtain service under warranty.
You must provide the original purchase receipt to validate your warranty and receive service.
Model Number: _________________________________________________
Serial Number: _________________________________________________
Date of Purchase: _______________________________________________
Need Help?
Before you call for service, here are a few things you can do to help us serve you better.
Read this owner’s manual:
It contains instructions to help you use and maintain your appliance properly.
If you receive a damaged appliance:
Immediately contact the retailer or builder that sold you the appliance.
Save time and money:
Check the troubleshooting section at the end of this manual before calling. This section
will help you solve common problems that may occur.
1-800-26- Danby
(1-800-263-2629)
1
SAFETY REQUIREMENTS
This appliance is not intended for use by persons
(including children) whose physical, sensory or
mental capabilities may be different or reduced,
or who lack experience or knowledge, unless such
persons receive supervision or training to operate
the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
To avoid risk of electric shock, do not operate this
appliance in an area that is likely to accumulate
standing water. If this condition develops, disconnect
the power supply before stepping into the water.
Do not store or use combustible materials such as
gasoline or other fl ammable vapors or liquids in the
vicinity of this or any other appliance.
Do not insert fi ngers or other objects into grills or
openings in the appliance.
Do not cover or block the intake and exhaust
openings.
Do not operate the appliance without the fi lter
installed.
Do not operate the appliance near heat sources.
This appliance is intended for indoor, residential
applications only. Do not use this appliance
outdoors. Do not use this appliance for commercial
or industrial applications.
If the air conditioner is transported on its back or
side, it must be allowed to stand upright for 6 hours
before plugging in to avoid damage to internal
components.
Keep the appliance away from walls, furniture and
curtains with a clearance of at least 30 cm (12
inches) on all sides.
GROUNDING INSTRUCTIONS
This appliance must be grounded. Grounding
reduces the risk of electrical shock by providing an
escape wire for the electrical current.
This appliance has a cord that has a grounding
wire with a 3-prong plug. The power cord must be
plugged into an outlet that is properly grounded.
If the outlet is a 2-prong wall outlet, it must be
replaced with a properly grounded 3-prong wall
outlet. The serial rating plate indicates the voltage
and frequency the appliance is designed for.
WARNING - Improper use of the grounding
plug can result in a risk of electric shock.
Consult a qualifi ed electrician or service agent
if the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not connect the appliance to extension cords,
adapters or together with another appliance in the
same wall outlet.
Do not splice the power cord. Do not under any
circumstances cut or remove the third ground prong
from the power cord.
If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent or
similar qualifi ed person in order to avoid hazard.
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
2
INSTALLATION INSTRUCTIONS
3
ACCESSORIES
1. Air outlet adapter
2. Exhaust hose
3. Window slider adapter
4. 2 Bolts
5. Window slider A
6. Window slider B and C
7. Foam seal A (adhesive)
8. Foam seal B (adhesive)
9. Foam seal C (non-adhesive)
10. Security bracket and 2 screws
11. Drain hose
12. Power cord storage band
13. Remote control and batteries
REQUIRED TOOLS
1. Medium sized Phillips screwdriver
2. Tape measure or ruler
3. Knife or scissors
4. Saw (in the event that the window sliders need to
be cut to size)
ON/OFF
TEMP
S
H
C
O
U
R
T
T
T
I
O
M
N
ER
T
I
O
M
F
E
F
R
MOD E
FAN
LED
SLEEP
SWING
1
2
3
4
5
6
7
8
9
10
11
12
13
FM
ION
INSTALLATION INSTRUCTIONS
4
INSTALLING THE WINDOW KIT
The instructions below can be used for either a hung
window or a sliding window application.
1. Measure the window opening where the window
kit will be installed. Assemble as many sliders
as necessary to fi t the window. If the window
opening is less that the minimum length of a
single slider, use the slider that has the hole in it
and cut it to the correct length. Make sure not to
cut the end that has the hole as this is necessary
to attach the exhaust hose adapter. Cut the
adhesive foam seals to the correct length for the
window and attach them to the window sash
and frame.
2. Connect the window slider adapter to the
window slider by gently pressing it into the hole
in the slider until it clicks into place.
3. Attach the exhaust hose to the window slider
adapter by gently pressing it into the adapter
until it clicks into place.
4. Install the slider kit and hose assembly and close
the window to hold it in place.
5. Attach the air outlet adapter to the back of the
appliance by sliding it down into the channel
around the air outlet. Attach the hose to the air
outlet adapter on the back of the appliance by
gently pressing it into the adapter until it clicks
into place.
6. Cut the non-adhesive foam seal to match the
width of the window and insert it between the
glass and the window frame to prevent air and
insects from getting into the room.
7. Install the security bracket in the window frame
with the provided screws.
A
B
A
B
1
2
3
4
5
6
7
Note: Do not over extend or bend the hose as this
will impede air fl ow.
OPERATING INSTRUCTIONS
5
FEATURES
Front
1. Control panel
2. Louver
3. Handle (both sides)
4. Casters
Rear
1. Upper air fi lter and air intake
2. Continuous drain outlet
3. Lower air fi lter and air intake
4. Air outlet
5. Power cord storage band
6. Power cord
7. Overfl ow tray drain outlet
1
2
3
4
1
7
2
3
5
6
4
LOCATION
Place the air conditioner on a smooth, level fl oor
that is strong enough to support it and all included
accessories.
Make sure the appliance is level to minimize noise
and vibration.
The appliance must be installed near a grounded
receptacle and the overfl ow drain outlet on the rear
of the appliance must be accessible.
Do not cover air inlets or outlets or the remote
control receiver on the control panel.
The appliance requires 30 cm (12 inches) of
clearance on the front and sides.
The appliance requires at least 50 cm (20 inches) of
clearance on the back.
6
CONTROL PANEL
1. Swing and wireless connect button:
Press to start the auto swing feature. When auto
swing is activated, press again to stop the louver
at the desired angle.
Press and hold for three seconds to start using
the wireless connect feature.
2. Timer button: Press to start the automatic timer.
Light will indicate whether a timer is set.
3. Mode button: Press to select the desired mode.
Light will indicate current mode.
4. Up and down buttons:
Used to set the temperature and timer.
Press and hold both up and down buttons for
three seconds to change the temperature display
from °C to °F.
OPERATING INSTRUCTIONS
3sec3sec
1
2
3
4
5
6 7 8
5. LED display:
Shows the set temperature in °C or °F.
Shows the timer settings.
While on dry or fan mode, shows the room
temperature.
6. Fan and ionizer button:
Press to select fan speed; low, medium or high.
Light will indicate current speed.
Press and hold for three seconds to start the
ionizer.
7. Sleep button: Press to start the sleep feature.
8. Power button: Press to turn the appliance on or
off.
OPERATING INSTRUCTIONS
7
AUTOMATIC TIMER
To set the automatic off timer:
Ensure the appliance is turned on
Press the timer button and the indicator light will
illuminate
Press the up and down buttons to select the
desired amount of hours before the appliance
turns off
To set the automatic on timer:
Ensure the appliance is turned off
Press the timer button and the indicator light will
illuminate
Press the up and down buttons to select the
desired amount of hours before the appliance
turns on
Notes:
The timer button will increase the time in 0.5
hour increments up to 10 hours and then in 1
hour increments up to 24 hours
The display will revert back to showing the
previous temperature setting if the appliance
does not receive a signal within a 5 second
period during programming
Turning the appliance on or off at any time
or adjusting the timer setting to 0.0 hours will
cancel the timer settings
Using Timer On and Off Simultaneously
If there is a need for the appliance to turn on, run
for a set period of time and then turn off, the on
and off timers can be used at the same time by fi rst
setting one and then the other. Both indicator lights
will illuminate and the display will count down to
the appliance either turning off or on, whichever
function was set fi rst.
Note: The timer will not cycle the appliance on and
off indefi nitely. The on and off timers will function
one time and then the appliance will return to
regular functioning.
OPERATING MODES
• Cool Mode
Choose cool mode to set the cooling function. Use
the up and down buttons to choose the desired
temperature. When cool mode is selected, the fan
speed can be adjusted by pressing the fan button.
The temperature can be set within a range of 17 -
30°C (62 - 86°F).
The exhaust hose should be installed during cool
mode to ensure the best results.
• Dry Mode
Choose dry Mode to remove excess moisture
from the air during periods of high humidity. All
water pulled from the air will condense inside the
appliance and drain out the back.
The humidity and fan speed will be automatically set
and cannot be modifi ed in dry mode.
• Fan Mode
Choose fan mode to run the internal fan without
engaging the cooling function. Press the fan button
repeatedly to choose the fan speed.
• Auto Mode
Auto mode is a pre-set factory program that
automatically defi nes the mode and fan speed
based on the set temperature, the ambient
temperature and the ambient humidity.
• Heat Mode
Choose heat mode to set the heating function. Use
the up and down arrows to choose the desired
temperature. Press the fan button to adjust the fan
speed.
The temperature can be set within a range of 17 -
30°C (62 - 86°F).
OPERATING INSTRUCTIONS
8
FOLLOW ME FUNCTION
There is a temperature sensor built into the remote
control that will continuously collect the current
room temperature. Keep the remote control with
you and the appliance will automatically adjust the
set temperature based on the current temperature
where you are located to reach the most
comfortable condition and temperature.
Press the follow me button to activate the follow
me function. The remote will display the current
temperature at its location. The remote will send
a signal to the air conditioner every 3 minutes, so
long as you remain within range of the appliance.
The follow me light on the control panel of the
appliance will illuminate for 5 seconds every three
minutes to indicate that it has received a signal
from the remote. If the appliance does not receive a
signal from the remote during any 7 minute interval,
it will beep to indicate that the follow me mode has
ended.
The maximum distance for the follow me feature is
8 meters (26 feet). This feature is available in cool
and auto modes.
SLEEP FUNCTION
The sleep function can be used to conserve energy
during sleeping hours.
When selected, the set temperature will increase
by 1°C/2°F every half hour for one full hour. The
appliance will hold the new set temperature for
6 hours before automatically returning to normal
operation.
The sleep function can be canceled at any time by
pressing the sleep button.
IONIZER FEATURE
The ionizer feature is a form of air purifi cation that
negatively charges the air. Dust particles, pollen and
other particles in the air cannot pass through the
lter when they are negatively charged. This ensures
that the maximum amount of dust and dirt are
removed from the air. Additionally, the ionizer helps
to remove unwanted odors from the air.
WIRELESS CONNECTION
This appliance can be controlled with a wireless
application on your wireless device.
Visit https://www.danby.com/support/#apps
to download the application and learn about its
operation.
OPERATING INSTRUCTIONS
9
REMOTE CONTROL
1. Power button: Press to turn the appliance on or
off.
2. Mode button: Press to select the desired mode.
3. Fan button: Press to select fan speed.
4. Ionizer button: Press to activate the ionizer.
5. Sleep button: Press to start the sleep feature.
6. Swing button: Press to start the auto swing
feature. When auto swing is activated, press
again to stop the louver at the desired angle.
7. Follow me button: Press to activate the follow
me feature.
8. LED button: Press to turn the LED display on or
off.
9. Timer off button: Press to set the automatic off
timer.
10. Timer on button: Press to set the automatic on
timer.
11. Shor tcut button: Press to set and activate the
short cut function.
12. Up and down buttons:
Used to set the temperature.
Press and hold both up and down buttons for 3
seconds to change the temperature display from
°C to °F.
13. LED display:
Shows the set temperature in °C or °F or the
auto-timer settings.
While on dry or fan mode, shows the room
temperature.
1
2
3
4
5 6
7 8
9
10
11
12
13
Shortcut function (only available on remote):
Used to save a favourite setting.
Set the appliance to the temperature and fan
speed that you would like to set as a favourite.
Press and hold the shortcut button for 2 seconds.
Press the shortcut button at any point in future to
return to the favourite setting.
If no favourite is set, pressing the shortcut button
will cause the appliance to run in auto mode at
29°C (79°F), with fan speed set to auto.
OPERATING INSTRUCTIONS
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
1. Reorient or relocate the receiving antenna
2. Increase the separation between the equipment
and receiver
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected
4. Consult the dealer or an experienced radio/TV
technician for help
Changes or modifi cations not approved by the
party responsible for FCC compliance could void
the user’s authority to operate the equipment. This
appliance complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference
received, including interference that may cause
undesired operation.
This device complies with Canadian CAN ICES-3
(B) / NMB-3 (B)
REPLACING THE REMOTE BATTERIES
This air conditioner comes with two AAA batteries.
Place the batteries in the remote control before use.
1. Slide the back cover from the remote downward
to expose the battery compartment.
2. Insert the batteries, ensure to match the (+) and
(-) symbols on the ends of the batteries with the
symbols inside the battery compartment.
3. Slide the battery cover back into place.
Notes:
The air conditioner will not respond if curtains,
doors or other materials block the signal from
the remote control to the unit.
Prevent any liquid from contact with the remote
control. Do not expose the remote control to
direct sunlight or heat.
If the infrared signal receiver on the indoor unit
is exposed to direct sunlight, the air conditioner
may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
Do not mix old and new batteries or batteries of
different types.
Do not leave the batteries in the remote control
if it is not going to be used for more than 2
months.
IMPORTANT
Do not dispose of batteries as unsorted municipal
waste. Refer to local laws for proper disposal of
batteries.
10
WATER DRAINAGE
When the internal drain pan becomes full the
appliance will beep 8 times and the digital display
will show error code P1. The air conditioning or
dehumidifying action will stop but the fan may
continue to operate.
There are two methods to drain water from the
appliance.
1. Drain Plug
1. Turn the appliance off and unplug it from the
power source.
2. Carefully move the appliance to a location
where the water can be drained.
3. Remove the drain plug and allow the water to
completely drain.
4. Replace the bottom drain plug, pressing fi rmly to
ensure a tight fi t and no leaks.
5. The P1 error symbol will disappear and the
appliance will resume regular function once
power is restored.
2. Continuous Drain
During the Dry mode, you may wish to set up the
continuous drain option so that the appliance will
automatically drain collected water.
Remove the exhaust hose during Dry mode, it is
not necessary. Ensure that the appliance is turned
off and unplugged from the power source before
setting up the drain hose.
Remove the upper drain plug and attach the drain
hose that was provided with the appliance. Ensure
that there are no kinks or bends in the drain hose as
this can stop water from draining.
Place the open end of the drain hose over the
receptacle that the appliance will drain into; this
could be a basement fl oor drain, a sink or similar.
Remember that there is no drain pump in this
appliance, the continuous drain is activated by
gravity only. Ensure that the drain hose goes straight
down toward the fl oor from the drain connection.
If the hose is not positioned directly downwards,
water will not drain correctly.
11
1
2
OPERATING INSTRUCTIONS
CARE & MAINTENANCE
CLEANING
Unplug the appliance before cleaning or
servicing.
Clean the cabinet with a lukewarm damp cloth
and neutral detergent. Dry the cabinet with a
lint-free dry cloth.
Do not use gasoline, paint thinner or other
chemicals to clean the appliance.
Do not wash the appliance directly under a tap
or using a hose. It may cause electrical damage.
AIR FILTER
The air fi lter in this appliance should be cleaned
every two weeks to ensure ef cient performance.
In households with animals, the air fi lters may need
to be cleaned more often and the external grills may
need to be wiped to prevent blocked air fl ow.
Do not operate this appliance without the air fi lter
installed.
LONG-TERM STORAGE
1. Drain all water from the appliance.
2. Run the appliance on Fan mode for half a day in
a warm room to dry the inside of the appliance
and prevent mold formation.
3. Turn off the appliance and unplug it, wrap the
cord and bundle it with tape.
4. Remove the batteries from the remote control.
5. Clean the air fi lters and reinstall them.
6. Store the appliance is a cool, dark place.
Prolonged exposure to direct sunlight or extreme
heat can shorten the lifespan of the appliance.
DISPOSAL
This appliance should not be treated as regular
household waste. Check for local regulatory
compliance regarding the approved and safe
disposal of this appliance.
ERROR CODES
E1 - room temperature sensor error
E2 - evaporator temperature sensor error
E3 - condenser temperature sensor error
E4 - display panel communication error
E7 - zero crossing malfunction
P1 - water tray is full - attach drain hose and drain
excess water
12
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
Appliance will not operate Plug is not fully inserted into the wall outlet
Blown fuse or circuit breaker
Insuffi cient cooling • Air lters are dirty
Blocked air fl ow
Appliance size is too small for application
Noise The ground is not level
• Air lters are dirty
Gurgling sounds are normal; this is the refrigerant moving inside
the appliance
Odors Formation of mold or mildew on internal wet surfaces
Place an algaecide tablet in base pan; push the tablet through
the grill on the back of the appliance
13
Danby Consumer Care: 1-800-263-2629 or consumerservice@danby.com
Hours of operation:
Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time
Friday 8:30 am - 4:00 pm Eastern Standard Time
Information in this manual is subject to change without notice.
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an authorized service
depot. Any appliance requiring service outside the limited boundaries of “In Home Service”, will be the consumer’s
responsibility to transport at their own expense to the original point of purchase or a service depot for repair. If the
appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center, it must
be delivered to the nearest authorized Danby Service Depot by the purchaser.
Transportation charges to and from the service location are not protected by this warranty and are the
responsibility of the purchaser.
During the first twenty four (24) months, any functional parts of this product found to be defective, will be repaired
or replaced, at warrantor’s option, at no charge to the original purchaser.
Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where
service must be performed by a qualified service technician. If service is performed on the unit by anyone other
than an authorized service depot, all obligations of Danby under this warranty shall be void.
First 24 months
To obtain service
Boundaries of
in-home service
LIMITED “IN HOME” WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used
under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby
Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made
or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any
warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly
excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,
howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the
purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by
the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (ie. extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor
application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).
Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present
the proof of purchase to our authorized service depot.
Warranty Service
In Home
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
1-800-263-2629
04/17
15
Bienvenue
Bienvenue à la famille Danby. Nous sommes fi ers de la qualité de nos produits et nous croyons
en le service fi able. Nous vous suggérons de lire ce manual d’utilisation avant de brancher
votre nouvel appareil car il contient des informations inportantes sur l’utilisation, la sécurité, le
dépannage et la maintenance, afi n d’assurer la fi abilité et la longévité de votre appareil.
Visitez www.Danby.com pour accéder aux outils d’autoservice, aux FAQ et bien plus encore. Pour
obtenir de l’aide supplémentaire, composez 1-800-263-2629.
Notez les informations ci-dessous; Vous aurez besoin de cette information pour obtenir un
service sous garantie.
Vous devez fournir le reçu d’achat original pour valider votre garantie et recevoir le service.
Numéro de modèle: _____________________________________________
Numéro de serie: _______________________________________________
Date d’achat: __________________________________________________
Besoin d’assistance?
Avant d’appeler pour service, voici quelques choses que vous pouvez faire pour nous
aider à mieux vous servir.
Lire ce manuel du propriétaire:
Il contient des instructions pour vous aider à utiliser et à maintenir votre appareil
correctement.
Si vous recevez un appareil endommagé:
Contactez immédiatement le revendeur ou l’entrepreneur qui vous a vendu l’appareil.
Gagnez du temps et de l’argent:
Avant d’appeler pour service, consultez la section de dépannage à la fi n de ce manuel.
Cette section vous aidera à résoudre les problèmes courants pouvant survenir.
1-800-26- Danby
(1-800-263-2629)
EXIGENCES DE SÉCURITÉ
Cet appareil n’est pas destiné à être utilisé par
des personnes (y compris des enfants) dont les
capacités physiques, sensorielles ou mentales
peuvent être différentes ou réduites, ou qui n’ont
pas d’expérience ou de connaissances, à moins
que ces personnes ne soient surveillées ou formées
pour faire fonctionner l’appareil par une personne
responsable de leur sécurité.
Les enfants devraient être surveillés pour s’assurer
qu’ils ne jouent pas avec l’appareil.
Pour éviter tout risque de choc électrique, ne pas
utiliser cet appareil dans une zone susceptible
d’accumuler de l’eau stagnante. Si cette condition
se développe, débranchez l’alimentation avant de
pénétrer dans l’eau.
Ne pas stocker ou utiliser des matériaux
combustibles tels que de l’essence ou d’autres
vapeurs ou liquides infl ammables à proximité de ce
ou d’un autre appareil.
Ne pas insérer de doigts ou d’autres objets dans
des grilles ou des ouvertures dans l’appareil.
Ne pas couvrir ou bloquer les ouvertures
d’admission et d’échappement.
N’utilisez pas l’appareil sans le fi ltre installé.
N’utilisez pas l’appareil à proximité de sources de
chaleur.
Cet appareil est destiné uniquement à des
applications résidentielles et intérieures. N’utilisez
pas cet appareil à l’extérieur. N’utilisez pas cet
appareil pour des applications commerciales ou
industrielles.
Si le climatiseur est transporté sur son dos
ou sur son côté, il doit être maintenu debout
pendant 6 heures avant de brancher pour éviter
d’endommager les composants internes.
Gardez l’appareil à l’écart des murs, des meubles
et des rideaux avec un jeu d’au moins 30 cm (12
pouces) sur tous les côtés.
INSTRUCTIONS DE MISE À LA TERRE
Cet appareil doit être mis à la terre. La mise à
la terre réduit le risque de choc électrique en
fournissant un câble d’échappement pour le courant
électrique.
Cet appareil possède un cordon doté d’un fi l de
mise à la terre avec une fi che à 3 broches. Le
cordon d’alimentation doit être branché sur une
prise correctement mise à la terre. Si la sortie
est une prise murale à 2 broches, elle doit être
remplacée par une prise murale à 3 broches
correctement mise à la terre. La plaque signalétique
en série indique la tension et la fréquence
auxquelles l’appareil est conçu.
AVERTISSEMENT - L’utilisation incorrecte de la
che de mise à la terre peut entraîner un risque
d’électrocution. Consultez un électricien qualifi é
ou un agent de service si les instructions de mise
à la terre ne sont pas complètement comprises ou
s’il existe un doute quant à savoir si l’appareil est
correctement mis à la terre.
Ne branchez pas l’appareil à des rallonges, des
adaptateurs ou à un autre appareil dans la même
prise murale.
Ne pas épisser le cordon d’alimentation. Ne coupez
ou retirez en aucun cas la troisième broche du
cordon d’alimentation.
Si le cordon d’alimentation est endommagé, il
doit être remplacé par le fabricant, son agent de
maintenance ou une personne qualifi ée similaire
afi n d’éviter tout risque.
Informations importantes de sécurité
LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ
GARDEZ CES INSTRUCTIONS!
16
INSTRUCTIONS D’INSTALLATION
17
ACCESSOIRES
1. Adaptateur de sortie d’air
2. Tuyau d’échappement
3. Adaptateur de glissière de fenêtre
4. 2 boulons
5. Curseur de fenêtre A
6. Curseur de fenêtre B et C
7. Joint en mousse A (adhésif)
8. Joint en mousse B (adhésif)
9. Joint en mousse C (non adhésif)
10. Support de sécurité et 2 vis
11. Tuyau de drainage
12. Bande de stockage du cordon d’alimentation
13. Télécommande et batteries
OUTILS REQUIS
1. Tournevis Phillips de taille moyenne
2. Ruban à mesurer ou règle
3. Couteau ou ciseaux
4. Scie (dans le cas où les curseurs de fenêtre
doivent être coupés en taille)
ON/OFF
TEMP
S
H
C
O
U
R
T
T
T
I
O
M
N
ER
T
I
O
M
F
E
F
R
MOD E
FAN
LED
SLEEP
SWING
1
2
3
4
5
6
7
8
9
10
11
12
13
FM
ION
INSTRUCTIONS D’INSTALLATION
18
Remarque: Ne pas trop étendre ni plier le tuyau,
car cela entravera le fl ux d’air.
INSTALLER LE KIT DE FENÊTRE
Les instructions ci-dessous peuvent être utilisées pour
une fenêtre suspendue ou pour une application de
fenêtre coulissante.
1. Mesurer l’ouverture de la fenêtre où le kit de
fenêtre sera installé. Assemblez autant de
curseurs que nécessaire pour s’adapter à la
fenêtre. Si l’ouverture de la fenêtre est inférieure
à la longueur minimale d’un curseur, utilisez
le curseur comportant le trou et coupez-le à la
longueur appropriée. Veillez à ne pas couper
l’extrémité comportant le trou car cela est
nécessaire pour fi xer l’adaptateur de tuyau
d’échappement. Coupez les joints de mousse
adhésifs à la longueur appropriée pour la
fenêtre et fi xez-les à l’ouvrant et au cadre de la
fenêtre.
2. Connectez l’adaptateur de curseur de fenêtre
au curseur de fenêtre en appuyant doucement
dessus dans le trou du curseur jusqu’à ce qu’il
s’enclenche.
3. Fixez le tuyau d’échappement à l’adaptateur
de glissière de fenêtre en appuyant doucement
dessus jusqu’à ce que vous entendiez un déclic.
4. Installez le kit coulisseau et le tuyau, puis fermez
la fenêtre pour la maintenir en place.
5. Fixez l’adaptateur de sortie d’air à l’arrière
de l’appareil en le faisant glisser dans le
canal autour de la sortie d’air. Fixez le tuyau
à l’adaptateur de sortie d’air à l’arrière de
l’appareil en appuyant doucement dessus dans
l’adaptateur jusqu’à ce qu’il s’enclenche.
6. Coupez le joint en mousse non adhésif en
fonction de la largeur de la fenêtre et insérez-
le entre le verre et le cadre de la fenêtre pour
empêcher l’air et les insectes de pénétrer dans la
pièce.
7. Installez le support de sécurité dans le cadre de
la fenêtre avec les vis fournies.
A
B
A
B
1
2
3
4
5
6
7
19
CARACTÉRISTIQUES
Avant
1. Panneau de contrôle
2. Persienne
3. Poignée (des deux côtés)
4. Roulettes
Arrière
1. Filtre à air supérieur et prise d’air
2. Sortie de vidange continue
3. Filtre à air inférieur et prise d’air
4. Sortie d’air
5. Bande de stockage du cordon d’alimentation
6. Cordon d’alimentation
7. Sortie de vidange du bac à débordement
EMPLACEMENT
Placez le climatiseur sur un plancher lisse et plat
qui est assez solide pour le supporter et tous les
accessoires inclus.
Assurez-vous que l’appareil est à niveau pour
minimiser les bruits et les vibrations.
L’appareil doit être installé près d’une prise de
mise à la terre et la sortie de vidange à l’arrière de
l’appareil doit être accessible.
Ne pas couvrir les entrées d’air ou les prises de
courant ou le récepteur de la télécommande sur le
panneau de commande.
L’appareil nécessite un dégagement de 30 cm (12
pouces) sur le devant et sur les côtés.
L’appareil nécessite au moins 50 cm (20 pouces) de
dégagement sur le dos.
1
2
3
4
INSTRUCTIONS D’UTILISATION
1
7
2
3
5
6
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Danby DPA140HB1BDB-6 Le manuel du propriétaire

Taper
Le manuel du propriétaire