CERTIFICATION: cULus WET
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet.
Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION
COLLECTION
APPLICATION MODEL NO.
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that
may occur. It must be understood that common sense, caution and care,
are factors that can’t be built into any product. These factors must be
supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
WHAT WE PROVIDE
•
Mounting Hardware
• Fixture Assembly
• Rubber gasket
• Back plate
• 2 X A19 E-26 LED
bulbs
WHAT YOU NEED
•
Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
recognized.
1
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
WALL FIXTURE
20389LEDDMGLP
NO.
20389LEDDMGLP
TRIDENT
CERTIFICATION: cULus WET
PREPARE THE FIXTURE AND INSERT THE BULBS
If there is an existing fixture remove it. Expose the supply
wires from the J-box and pass the wires through the
designated hole in the universal plate rubber, gasket and
fixture back plate. Mount the universal plate, rubber gasket
and back plate with the supplied screws. Unscrew the two
screws on the top and bottom of the fixture that are securing
the glass covers to the fixture.
Insert the bulbs into each socket.
DO NOT EXCEED THE MAXIMUM WATTAGE
AS STATED ON THE WARNING LABEL.
Replace the glass covers and secure with supplied screws.
MAKE WIRE CONNECTIONS
Connect the black supply wire to the black fixture wire.
Secure with the supplied wire nuts. Connect the white supply
wire to the white fixture wire. Secure with the supplied wire
nuts. Attach the green J-Box wire around green hexagonal
head screw or connect it to the green supply grounding
wire of the fixture. Secure all wires with electrical tape (not
supplied). Tuck all wires carefully into the J-box.
MOUNT THE FIXTURE
Place the fixture canopy over the fixture back plate such
that the fixture is flush against the wall. Insert the supplied
screws into the holes in the fixture canopy ensuring that they
fit into the indented area on the back plate.
*This fixture is wet location rated. In order to ensure that
moisture does not enter the outlet box and cause a short
circuit, clear caulking should be used to seal the space
between the fixture mounting bracket and the wall.
Ensure that a space is left at the bottom to allow the
escape of moisture. It is recommended that
Indoor/Outdoor Silicon Sealant be used for this
purpose**
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
2
Dimmable fixture - see attached list for compatible dimmer switches. VER: 17.10.1
2
3
4
1
NO. 20389LEDDMGLP
-
1
-
2
Access Lighting TRIDENT 20389LEDDMGLP Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Access Lighting 20351 Guide d'installation
-
Access Lighting 20292LEDDLP-SAT/FST Manuel utilisateur
-
-
-
-
Access 28030-1C-BS/AMB Mode d'emploi
-
-
-
-
