SCOTT 2023 SOLACE eRIDE Manuel utilisateur

RANGE EXTENDER

MANUAL

HPR Range Extender V01 160 Wh

User Manual

EN

EN – 2

1 Safety

These instruction contains information that you must observe for

your personal safety and to prevent personal injury and damage

to property. They are highlighted by warning triangles and shown

below according to the degree of danger.

►Read the instructions completely before start-up and use. This will help

you to avoid hazards and errors.

►Keep the manual for future reference. This user manual is an integral part

of the product and must be handed over to third parties in case of resale.

NOTE

Also observe the additional documentation for the other components of the

HPR50 drive system as well as the documentation enclosed with the e-bike.

1.1 Hazard classiﬁcation

HAZARD

The signal word indicates a hazard with a high degree of risk which will

result in death or serious injury if not avoided.

WARNING

The signal word indicates a hazard with a medium level of risk which will

result in death or serious injury if not avoided.

CAUTION

The signal word indicates a hazard with a low level of risk which could result

in a minor or moderate injury if not avoided.

NOTE

A note in the sense of this instruction is important information about the

product or the respective part of the instruction to which special attention

is to be drawn.

EN – 3

1.2 Intended Use

The HPR Range Extender is intended exclusively for supplying power to the

HPR50 drive system and must not be used for any other purpose.

Any other use or use that goes beyond this is considered improper and will

result in the loss of the warranty. In case of non-intended use, TQ-Systems

GmbH assumes no liability for any damage that may occur and no warranty

for proper and functional operation of the product.

Intended use also includes observing these instructions and all the information

contained therein as well as the information on intended use in the supple-

mentary documents enclosed with the e-bike.

Faultless and safe operation of the product requires proper transport, storage,

installation and operation.

1.3 Safety instructions for the HPR Range Extender

—The installation of the HPR Range Extender may only be carried out by

authorised dealers. The persons must be qualiﬁed accordingly, e.g. by

training as a two-wheel mechatronics technician. They must be able to

recognise possible dangers during installation. Otherwise, there is a risk

that the Range Extender or other lithium-ion batteries on the e-bike will

be damaged or that the Range Extender comes off during the ride due to

incorrect mounting.

—Explosion and ﬁre hazard with damaged Range Extender housing

• If the Range Extender housing is damaged, make sure to have it

replaced by a TQ authorised bicycle dealer, even if the Range Extender

is still functional.

• Do not make any repair attempts under any circumstances.

—Explosion and ﬁre hazard when short-circuiting the Range Extender terminals

• Keep the Range Extender away from metallic objects as there is a risk

of short circuits. Do not allow nails, screws or other small, sharp and/

or metallic objects to come into contact with the Range Extender

(charging/discharging socket).

—Risk of explosion and ﬁre in case of high heat, ﬁre or contact with water

Protect the battery from ﬁre, high heat and also from extended direct

exposure to sunlight.

• Never immerse the battery in water.

—Danger of poisoning by gases from a smoking or burning Range Extender

in case of damaged Range Extender or improper use.

• Be careful not to breathe in the highly toxic gases from a smoking or

burning Range Extender.

EN – 4

• Ensure good ventilation and consult a doctor if you notice any unde-

sirable effects on the respiratory organs. The vapors may irritate the

respiratory organs.

—Liquid may leak from the battery if used improperly. Avoid any contact

with this liquid. Wash it off with water if you do come into contact with the

liquid. Also seek medical attention if the liquid has come into contact with

your eyes. Liquid leaking from the Range Extender can cause irritation or

burns.

—Never subject the Range Extender to mechanical shocks to prevent

damage to the Range Extender.

—Only adults are allowed to handle the Range Extender. Keep the battery

away from children.

Never open the Range Extender case or attempt to disassemble the Range

Extender.

—Never break or puncture the Range Extender.

—Only charge the Range Extender in well ventilated rooms.

—Only use the intended TQ charger to charge the Range Extender.

—Use only original HPR Range Extenders to supply power to the drive

system.

EN – 5

2 Technical data

Nominal voltage 50.4 V

Nominal capacity 2.8 Ah

Nominal energy 160 Wh

Discharge logic When operating the e-bike, the Range Extender

is discharged ﬁrst afterwards the battery.

Dimensions ∅ 76 mm, length 185 mm / ∅ 3”, length 7.3”

Protection class IP66

Charging temperature

Operating temperature

Storage temperature

0 °C bis 40 °C / 32 °F bis 104 °F

-10 °C bis 60 °C / 14 °F bis 140 °F

10 °C bis 20 °C / 50 °F bis 68 °F

Weight approx. 950 g / 2.1 lbs

(without frame fastening like FIDLOCK®)

Tab. 1: Technical data – HPR Range Extender

EN – 6

3 Operation

3.1 Installing the Range Extender on the e-bike

The design of the mounting system for the Range Extender on the e-bike

depends on the manufacturer. This section shows how to mount the Range

Extender on the down tube of the e-bike using the FIDLOCK® system.

Make sure especially in case of retroﬁt that

no components of the e-bike such as the

battery or wiring harness are damaged when

installing the Range Extender.

Pay special attention to the following points:

—The assembly of the HPR Range Extender

may only be carried out by authorised

dealers. The personnel must be appropriately qualiﬁed, e.g. through

training as a two-wheel mechatronics technician. They must be able to

recognise possible dangers during assembly. Otherwise, there is a risk

that the Range Extender or other lithium-ion batteries on the e-bike will be

damaged or that the Range Extender comes loose during the ride due to

insufﬁcient fastening.

—Selection of the correct screw heads and screw lengths.

—Selection of the positions recommended by the bicycle manufacturer for

the attachment.

3.1.1 Fitting the FIDLOCK® Bike Base to the e-bike

WARNING

Fire hazard due to damage to the battery inside the e-bike frame caused

by using screws that are too long.

►Only use the screws provided by the bicycle manufacturer or the

ISO 7380–1 M5 × 10 A2 button head screws included in the scope of

delivery to attach the FIDLOCK® Bike Base.

Using screws that are too long can damage the battery inside the e-bike

frame.

EN – 7

CAUTION

Risk of accident due to release of the Range Extender from the locking

mechanism

►Only use the screws provided by the bicycle manufacturer or the

ISO 7380–1 M5 × 10 A2 button head screws included in the scope of

delivery to attach the FIDLOCK® Bike Base.

Screws with a higher head mean that the FIDLOCK® Force Connector on the

Range Extender is not ﬁrmly connected to the FIDLOCK® Bike Base and will

come loose while riding.

►Fasten the FIDLOCK® Bike Base

(Pos. 1 in Fig. 1) with the two

button head screws (Pos. 2 in

Fig. 1) in the threads provided for

this purpose (Pos. 3 in Fig. 1, follow

the speciﬁcations of the bicycle

manufacturer) inside the e-bike

frame.

►Tighten the two button head bolts

with a torque of 2 Nm or to the

max. torque values speciﬁed by

the bicycle manufacturer.

NOTE

►Observe the inscription

engraved “upside>>” when

mounting on the FIDLOCK®

Bike Base (Pos. 1 in Fig. 2). The

upper edge of the FIDLOCK®

logo (Pos. 2 in Fig. 2) on the

FIDLOCK® Force Connector

must point in the direction of

the arrow from “upside >>”.

Fig. 1: Fasten the FIDLOCK® Bike Base

to the e-bike

1

23

4

Fig. 2: Orientation of FIDLOCK® Bike

Base and FIDLOCK® Force

Connector

1

2

EN – 8

3.1.2 Fasten FIDLOCK® Force Connector to Range Extender

WARNING

Fire hazard due to damage to the Range Extender by using screws that are

too long

►Only use the screws provided by the bicycle manufacturer or the

ISO 4762 M4 × 16 A2 cylinder screws included in the scope of delivery to

fasten the FIDLOCK® Force Connector.

Using screws that are too long can damage the battery in the Range

Extender.

►Fasten the FIDLOCK® Force

Connector (Pos. 1 in Fig. 3) in the

threads (Pos. 3 in Fig. 3) in the

Range Extender using the four

M4 × 16 cylinder screws supplied

(Pos. 2 in Fig. 3).

►Tighten the four cylinder screws

with a torque of 1.0 Nm.

3.1.3 Insert and lock the

Range Extender on the

FIDLOCK® Bike Base

►Place the Range Extender (Pos. 1 in

Fig. 4) with the fastened FIDLOCK®

Force Connector (Pos. 2 in Fig. 4)

diagonally onto the FIDLOCK®

Bike Base (Pos. 3 in Fig. 4). The pin

(Pos. 4 in Fig. 4) on the FIDLOCK®

Bike Base must slide into the

corresponding socket in the

FIDLOCK® Force Connector when

it is put on. The magnets support

the attachment and the Range

Extender should automatically lock

into place with an audible click.

Fig. 3: Fasten FIDLOCK® Force

Connector to Range Extender

1

2

3

Fig. 4: Insert Range Extender

1

2

3

4

EN – 9

3.1.4 Locking the Range Extender into the FIDLOCK® Bike

Base

Fig. 5: FIDLOCK® system unlocked

1

Fig. 6: FIDLOCK® system locked

1

The FIDLOCK® system is still unlocked after inserting the Range Extender. This

condition is indicated by the red ﬁeld (Pos. 1 in Fig. 5) on the locking tab.

►Push the locking tab in as far as it will go (see Pos. 1 in Fig. 6), to ﬁx the

Range Extender ﬁrmly in place.

CAUTION

Risk of accident due to unlocked Range Extender

►Always lock the Range Extender with the locking tab in the FIDLOCK®

system before go riding.

Otherwise there is a risk that the Range Extender will come loose while

riding, which can lead to a crash.

NOTE

►Check the FIDLOCK® Bike Base and the FIDLOCK® Force Connector for

dirt and damage before every ride.

For more information on the FIDLOCK® TWIST system and compatible acces-

sories, please visit http://www.ﬁdlock-bike.com/TQ.

EN – 10

3.1.5 Connect the connection cable to the Range Extender

►Connect the plug (Pos. 1 in Fig. 7)

of the connection cable to the

socket (Pos. 2 in Fig. 7) in the

Range Extender.

►Fasten the connector to the Range

Extender with the M3 × 8 socket

head screw (Pos. 3 in Fig. 7)

included in the scope of delivery

of the cable, with a torque of 1 Nm.

Never use a longer screw. Other-

wise there is a risk of damaging

the electronics in the Range

Extender.

NOTE

Connecting cables are available in various versions with different cable

lengths and connector orientations to meet the requirements of the respec-

tive installation situation.

►Enquire at the e-bike manufacturer about the connection cable you

need.

3.1.6 Connect the connection cable to the charging port of

the e-bike

►Unfold the cover (Pos. 1 in Fig. 8)

of the charging port (Pos. 2 in

Fig. 8) on the e-bike frame.

►Check that the terminals in the

charging port are free of dirt and

clean them if necessary.

►Align the connector (Pos. 3 in

Fig. 8) of the connection cable so

that the connector coding of the

plug and charging port match.

►Insert the plug into the charging

port and secure the plug with the

cover (Pos. 1 in Fig. 8).

Fig. 7: Fasten the connection cable to

the Range Extender

1

2

3

Fig. 8: Connect the connection cable

to the charging port

2

3

1

EN – 11

CAUTION

Risk of accident due to free hanging connection cable on the Range Ex-

tender

►Always connect the Range Extender to the charging port of the battery

in the bicycle frame when you have installed the Range Extender on the

bicycle.

Otherwise there is a risk that the free hanging connection cable on the

Range Extender will get caught in the pedals while riding and so leads to

crash.

3.2 Range Extender charging

WARNING

Fire or electric shock hazard due to damage to battery, Range Extender,

charger, cable and plug.

►Never charge the Range Extender if you notice any damage to the

battery, Range Extender, charger, cables or connectors.

►Only perform the charging process in a place where there are no ﬂam-

mable materials in surrounding.

►Never leave the charging process unattended.

NOTE

—The drive system detects whether the Range Extender is connected

to the charging port of the battery in the bicycle frame. In this case

the drive system is deactivated during the charging process for safety

reasons.

—The charging system detects whether the Range Extender is connected

to the charging port of the battery in the bicycle frame. In this case both

are charged, ﬁrst the battery and afterwards the Range Extender.

EN – 12

CAUTION

Risk of accident due to activated drive system during the charging pro-

cess

►Always connect the Range Extender to the charging port of the battery

in the bicycle frame when you have installed the Range Extender on the

bicycle.

This is the only way to ensure that the drive system is deactivated during

charging. Otherwise there is a risk that you can start the drive system during

charging and that the plugged-in charging cable will cause damage or leads

to a crash.

►Connect the charger to the power supply.

►Unfold the cover (Pos. 1 in Fig. 9)

on the charging port of the Range

Extender.

►Check that the terminals in the

charging port (Pos. 2 in Fig. 9)

are free of dirt and clean them if

necessary.

►Insert the charging plug (Pos. 3

in Fig. 9) of the charger into

the charging port of the Range

Extender.

►Pull the charger plug of the

charger out of the charging port of

the Range Extender when charging is complete.

►Close the cover on the charging port when charging is complete.

►Disconnect the charger from the power supply.

1

2

3

Fig. 9: Range Extender charging

EN – 13

3.3 Notes on Charging

NOTE

The temperature of the Range Extender must be within the permissible

charging temperature range (0 °C to 40 °C / 32 °F to 104 °F). Otherwise the

charging process will not start.

—The Range Extender can be charged directly on the e-bike or separately.

—The drive system is deactivated during charging when the Range Extender

is connected to the battery charging port in the bicycle frame.

—The charging status of the Range Extender can be read on the display and

on the 5 LEDs on the side of the Range Extender. Brieﬂy cover the light

sensor to the left of the LEDs with a ﬁnger to activate this display.

—New Range Extenders have a state of charge of 20% to 30% due to trans-

port regulations and must be recharged within less than 6 months after

manufacturing.

—The Range Extender should be recharged immediately after it has been

completely discharged (state of charge <5 %).

—1 charge cycle can consist of a full charge of the Range Extender capacity

(0% to 100%) or several partial charges that add up to 100% of the charge

capacity.

—The Range Extender capacity should be at least 60 % after 500 charging

cycles.

EN – 14

4 Transport

—The transport of lithium batteries is subject to country-speciﬁc laws and

regulations. Inform yourself about the respective regional regulations and

observe them during transport.

—For transport observe the special requirements for packaging and labeling

that apply in your country.

—Contact a TQ authorised bicycle dealer for information on transporting the

Range Extender and suitable transport packaging. For transport outside

the bicycle frame, we recommend a certiﬁed transport box.

5 Storage

—Store the Range Extender at room temperature (approx. 10 °C to 20 °C /

50 °F to 68 °F) and do not expose it to direct sunlight.

—Do not store the Range Extender near heat sources or other easily ﬂam-

mable materials.

—Store the Range Extender in dry rooms (humidity below 70 %) and protect

it from rain and moisture.

—Store the Range Extender only in rooms equipped with smoke detectors.

—Charge the Range Extender to approx. 30 % to 60 % before storage.

—Check the Range Extender every 6 months and recharge it to approx. 30 %

to 60 %.

—Fully charge the Range Extender before use.

—Do not store the Range Extender with the charger plugged in.

6 Cleaning

—Never immerse the Range Extender in water to clean it.

—Never clean the Range Extender with a water jet.

—Only clean the Range Extender with a soft, damp cloth.

—Please contact a TQ authorised bicycle dealer, if the Range Extender is no

longer functional.

EN – 15

7 Maintenance and Service

All service, repair or maintenance work performed by a TQ authorized bicycle

dealer. Your bicycle dealer can also help you with questions about bicycle use,

service, repair or maintenance.

8 Environmentally friendly disposal

The components of the drive system and the batteries must not be

disposed of in the residual waste garbage can.

—Dispose of metal and plastic components in accordance with

country-speciﬁc regulations.

—Dispose of electrical components in accordance with country-speciﬁc

regulations. In EU countries, for example, observe the national imple-

mentations of the Waste Electrical and Electronic Equipment Directive

2012/19/EU (WEEE).

—Dispose of batteries and rechargeable batteries in accordance with the

country-speciﬁc regulations. In EU countries, for example, observe the

national implementations of the Waste Battery Directive 2006/66/EC in

conjunction with Directives 2008/68/EC and (EU) 2020/1833.

—Observe addtitonally the regulations and laws of your country for disposal.

In addition you can return components of the drive system that are no longer

required to a bicycle dealer authorized by TQ.

We have checked the contents of this publication for conformity with the product

described. However, deviations cannot be ruled out so that we cannot accept any

liability for complete conformity and correctness.

The information in this publication is reviewed regularly and any necessary corrections

are included in subsequent editions.

All trademarks mentioned in this manual are the property of their respective owners.

TQ-Systems GmbH Art.-No.: HPR50-RE01-UM

Gut Delling l Mühlstraße 2 l 82229 Seefeld l Germany Rev0104 2022/08

Phone.: +49 8153 9308–308

ebike@tq-group.com l www.tq-ebike.com

NOTE

For more information and TQ product manuals in various language, please

visit www.tq-ebike.com/en/support/manuals or scan this QR-Code.

HPR Range Extender V01 160 Wh

Benutzerhandbuch

DE

DE – 2

1 Sicherheit

Diese Anleitung enthält Hinweise, die Sie zu Ihrer persönlichen

Sicherheit sowie zur Vermeidung von Personen- und Sachschäden

beachten müssen. Sie sind durch Warndreiecke hervorgehoben

und je nach Gefährdungsgrad im Folgenden dargestellt.

►Lesen Sie vor der Inbetriebnahme und Gebrauch die Anleitung vollständig

durch. Sie vermeiden dadurch Gefährdungen und Fehler.

►Bewahren Sie die Anleitung zum späteren Nachschlagen auf. Dieses Benut-

zerhandbuch ist integraler Bestandteil des Produkts und muss bei Weiter-

gabe oder Verkauf an Dritte mitgegeben werden.

HINWEIS

Beachten Sie auch die zusätzliche Dokumentation für die weiteren Kompo-

nenten des Antriebssystems sowie die Dokumentation, die Ihrem E-Bike

beiliegt.

1.1 Gefahrenklassiﬁzierung

GEFAHR

Das Signalwort bezeichnet eine Gefährdung mit einem hohen Risikograd,

die, wenn sie nicht vermieden wird, den Tod oder eine schwere Verletzung

zur Folge hat.

WARNUNG

Das Signalwort bezeichnet eine Gefährdung mit einem mittleren Risikograd,

die, wenn sie nicht vermieden wird, den Tod oder eine schwere Verletzung

zur Folge hat.

VORSICHT

Das Signalwort bezeichnet eine Gefährdung mit einem niedrigen Risikograd,

die, wenn sie nicht vermieden wird, eine geringfügige oder mäßige Verlet-

zung zur Folge haben könnte.

HINWEIS

Ein Hinweis im Sinne dieser Anleitung ist eine wichtige Information über

das Produkt oder den jeweiligen Teil der Anleitung, auf die besonders

aufmerksam gemacht werden soll.

DE – 3

1.2 Bestimmungsgemäßer Gebrauch

Der HPR Range Extender ist ausschließlich für die Stromversorgung des

Antriebssystems HPR50 vorgesehen und darf nicht für andere Zwecke

verwendet werden.

Eine andere oder darüber hinaus gehende Benutzung gilt als nicht bestim-

mungsgemäß und hat den Verlust der Gewährleistung zur Folge. Bei nicht

bestimmungsgemäßem Gebrauch übernimmt die TQ-Systems GmbH keine

Haftung für eventuell auftretende Schäden und keine Gewährleistung für

einwandfreies und funktionsgemäßes Arbeiten des Produkts.

Zum bestimmungsgemäßen Gebrauch gehört auch das Beachten dieser

Anleitung und aller darin enthaltenen Hinweise sowie der Informationen zum

bestimmungsgemäßen Gebrauch in den ergänzenden Dokumenten, die dem

E-Bike beiliegen.

Der einwandfreie und sichere Betrieb des Produkts setzt sachgemäßen Trans-

port, sachgemäße Lagerung, Montage und Inbetriebnahme voraus.

1.3 Sicherheitshinweise zum HPR Range Extender

—Die Montage des HPR Range Extender darf nur von autorisierten Händlern

durchgeführt werden. Das Personal muss entsprechend qualiﬁziert sein,

z.B. durch eine Ausbildung zum Zweiradmechatroniker. Es muss in der

Lage sein, mögliche Gefahren bei der Montage erkennen zu können. Ande-

renfalls besteht das Risiko, dass der Range Extender bzw. andere Lithium-

Ionen-Akkus am E-Bike beschädigt werden oder sich der Range Extender

aufgrund unzureichender Befestigung während der Fahrt löst.

—Explosions- und Brandgefahr bei beschädigtem Range-Extender-Gehäuse

• Lassen Sie den Range Extender bei beschädigtem Gehäuse unbedingt

von einem durch TQ autorisierten Fahrradhändler tauschen, auch wenn

der Range Extender noch funktionsfähig ist.

• Unternehmen Sie keinesfalls Reparaturversuche.

—Explosions- und Brandgefahr bei Kurzschließen der Range-Extender-Pole

• Halten Sie den Range Extender von metallischen Gegenständen fern,

da Kurzschlussgefahr besteht. Lassen Sie keine Nägel, Schrauben oder

andere kleine, scharfe und/oder metallische Gegenstände in Berüh-

rung mit dem Range Extender (Ladebuchse/Entladebuchse) kommen.

—Explosions- und Brandgefahr bei großer Hitze, Feuer oder Kontakt mit

Wasser

Vermeiden Sie die Einwirkung großer Hitze auf den Range Extender,

z. B. durch längere direkte Sonneneinstrahlung.

• Tauchen Sie den Range Extender niemals in Wasser.

La page charge ...

SCOTT 2023 SOLACE eRIDE Manuel utilisateur

SCOTT 2023 SOLACE eRIDE Manuel utilisateur

dans d''autres langues