Samsung LN40B750 Manuel utilisateur

LCD TV

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please

register your product at

www.samsung.com/register

Model Serial No.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comuníquese con SAMSUNG WORLDWIDE

Si desea formular alguna pregunta o comentario en relación con los productos de Samsung, comuníquese con el centro de

atención al cliente de SAMSUNG.

Country Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service

à la Clientèle 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

BN68-02111B-00

[750-NA]BN68-02111B-Eng.indb 1 2009-03-30 �� 1:42:42

Important Warranty Information Regarding Television Format Viewing

See the warranty card for more information on warranty terms.

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen

format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to

ll the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images

on screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no

more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites

or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that

exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in

the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary

patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection

and use, as well as burned-in images, are not covered by your Samsung limited warranty.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties.

In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396,

5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080,

and under US Published Patent Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for

commercial use. The license does not cover any product unit other than this product unit and the license does not extend to

any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with

this product unit. The license only covers the use of this product unit to encode and/or decode audio les conforming to the

ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not

conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for

commercial use. The license does not cover any product unit other than this product unit and the license does not extend to

any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with

this product unit. The license only covers the use of this product unit to encode and/or decode audio les conforming to the

ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not

conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung

Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG

will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and

in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specied, and to the

Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this

Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the

Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in

normal use of the product.

Excluded, but not limited to, are any originally specied provisions for, in-home or on-site services, minimum or maximum

repair times, exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864)

In Canada : 1-800-SAMSUNG

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as screen burn. To avoid such image retention, reduce the degree of brightness and contrast of the

screen when displaying a still image.

Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the

left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or

a game console may cause a similar effect to the screen. Damages caused by the above effect are not

covered by the Warranty.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To

prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

❑

N

●

N

❑

●

[750-NA]BN68-02111B-Eng.indb 1 2009-03-30 �� 1:42:42

Setting up Your TV

List of Features .................................................................................. 2

Accessories ....................................................................................... 2

Viewing the Control Panel ................................................................. 3

Viewing the Remote Control .............................................................. 4

Installing Batteries in the Remote Control ......................................... 5

Viewing the menus ............................................................................ 5

Plug & Play Feature ........................................................................... 7

Connections

Connecting VHF and UHF Antennas ................................................. 8

Connecting Cable TV......................................................................... 9

Viewing the Connection Panel ......................................................... 10

CHANNEL

Channel Menu ................................................................................. 13

Managing Channels ......................................................................... 14

PICTURE

Conguring the Picture Menu .......................................................... 16

Viewing Picture-in-Picture................................................................ 20

Using Your TV as a Computer (PC) Display .................................... 21

Setting up the TV with your PC........................................................ 22

SOUND

Conguring the Sound Menu ........................................................... 23

SETUP

Conguring the Setup Menu ............................................................ 25

Setting the Time ............................................................................... 28

Network Connection ........................................................................ 30

Setting the Network ......................................................................... 33

INPUT / SUPPORT

Input Menu ....................................................................................... 36

Support Menu .................................................................................. 36

Media Play (USB & DLNA)

Connecting a USB Device ............................................................... 39

Media Play Function ........................................................................ 40

Sorting the Photo List ...................................................................... 42

Photo List Option Menu ................................................................... 43

Viewing a Photo or Slide Show........................................................ 44

Slide Show Option Menu ................................................................. 45

Sorting the Music List ...................................................................... 47

Music List Option Menu ................................................................... 48

Playing Music .................................................................................. 49

Music Play option Menu .................................................................. 50

Sorting the Movie List ...................................................................... 50

Movie List Option Menu ................................................................... 51

Playing a Movie File ........................................................................ 51

■

Movie Play Option Menu ................................................................. 54

Using the Setup Menu ..................................................................... 55

Media Play-DLNA

Setting the DLNA Network ............................................................... 56

Installing the DLNA Application ........................................................ 57

Using the DLNA Application ............................................................. 58

Using the DLNA Function ................................................................ 60

ANYNET

+

Connecting Anynet

+

Devices ........................................................... 61

Setting Up Anynet

+

..........................................................................

62

Switching between Anynet

+

Devices ............................................... 62

Recording ........................................................................................ 63

Listening through a Receiver (Home Theater)................................. 63

Troubleshooting for Anynet

+

............................................................

64

Content Library

Using the Content Library ................................................................ 65

Using the TV Memory Contents....................................................... 66

Using the Content Management ...................................................... 67

Internet@TV

Getting Started with Internet@TV .................................................... 68

Editing Snippets in the Dock ............................................................ 71

Using the Prole Widget .................................................................. 71

Using the Yahoo!® Widget Gallery .................................................. 73

Using the Yahoo!® Weather Widget ................................................ 74

Using the Yahoo!® News Widget ..................................................... 74

Using the Yahoo!® Flickr Widget ..................................................... 75

Using the Yahoo!® Finance Widget ................................................. 76

Troubleshooting for internet@TV ..................................................... 76

Help Website ................................................................................... 76

Home Network Center

Home Network Center ..................................................................... 77

Setting Up the Home Network Center ............................................. 78

Using the Message Function ........................................................... 79

Using the Media Function ................................................................ 80

RECOMMENDATIONS

Troubleshooting ............................................................................... 81

Installing the Stand .......................................................................... 82

Disconnecting the Stand .................................................................. 82

Assembling the Cables .................................................................... 83

Wall Mount Kit Specications (VESA) ............................................. 83

Anti-Theft Kensington Lock ............................................................. 84

Securing the Installation Space ....................................................... 84

Securing the TV to a Wall or Cabinet .............................................. 85

Specications .................................................................................. 86

Dimensions ...................................................................................... 88

■

CONTENTS

English

License

TruSurround HD, SRS and symbol are trademarks of SRS Labs, Inc. TruSurround HD

technology is incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are

trademarks of Dolby Laboratories.

DivX® Certified to play DivX® video, including premium content.

Symbol

N O T

Press Note One-Touch Button TOOL Button

❑

English - 1

[750-NA]BN68-02111B-Eng.indb 1 2009-03-30 �� 1:42:42

English - 2

SETTING UP YOUR TV

To use your TV, you rst have to set it up to suit your environment.

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and specifications may be changed without notice in order to enhance product performance.

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

Automatic timer to turn the TV on and off.

A special sleep timer.

Excellent Digital Interface & Networking : With a built-in HD digital tuner, nonsubscription HD broadcasts can be viewed with

no Cable Box/Satellite receiver (Set-Top Box) needed.

HDMI/DVI connection of your PC to this TV.

Excellent Picture Quality

SRS TruSurround HD provides a virtual surround system.

Media Play: Allows you to play music files, pictures, and movies saved on a USB or DLNA device.

Internet@TV: You can use various internet services and view useful information and entertaining content.

Home Network Center: Allows you to configure a mobile message server or a DLNA media render.

Accessories

Remote Control (BN59-00851A)

& Batteries (AAA x 2)

Program CD

(BN59-00726D)

Cover-Bottom

(LN40B750: BN63-05385A)

(LN46B750: BN63-05254A)

(LN52B750: BN63-05314A)

Warranty Card /

Safety Guide

Stand Screw (X4)

(6002-001294)

Power Cord

(3903-000144)

TV-Holder & Screw (X1)

(BN96-10788A)

(Depending on the model)

Cleaning Cloth

(BN63-01798B)

Holder-Wire Cable

(BN61-05596A)

(Depending on the model)

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

The items color and shape may vary depending on the model.

N

¦

●

¦

N

(M4xL16)

[750-NA]BN68-02111B-Eng.indb 2 2009-03-30 �� 1:42:44

English - 3

Viewing the Control Panel

The product color and shape may vary depending on the model.

The front panel buttons can be activated by touching them with your finger.

1

P

(POWER): Press to turn the TV on and off.

2 POWER INDICATOR: Blinks and turns off when the power is on and lights up in stand-by mode.

3

z

: Press to change channels. In the on-screen menu, use the

z

buttons as you would use the ▼ and ▲

buttons on the remote control.

4

y

: Press to increase or decrease the volume. In the on-screen menu, use the

y

buttons as you would use the

◄ and ► buttons on the remote control.

5 MENU: Press to see an on-screen menu of your TV’s features.

6 SOURCE

E

: Toggles between all the available input sources. In the on-screen menu, use this button as you use the

ENTER

E

button on the remote control.

7 REMOTE CONTROL SENSOR: Aim the remote control towards this spot on the TV.

8 SPEAKERS

¦

N

8

6 5 4 37 21

[750-NA]BN68-02111B-Eng.indb 3 2009-03-30 �� 1:42:44

English - 4

Viewing the Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

The product color and shape may vary depending on the model.

1

POWER : Turns the TV on and

off.

2

TV : Selects the TV mode

directly.

3

NUMERIC BUTTONS : Press to

change the channel.

4

_

: Press to select additional

channels (digital) being

broadcast by the same station.

For example, to select channel

‘54-3’, press ‘54’, then press ‘

_

’

and ‘3’.

5

CH LIST : Used to display

Channel Lists on the screen.

6

TOOLS : Use to quickly select

frequently used functions.

7

INTERNET@ : Press to use

various internet services to

view useful information and

entertaining content.

8

COLOR BUTTONS : Use these

buttons in the Channel list,

Internet@TV, Media Play menu,

etc.

9

SOURCE: Press to display

and select the available video

sources.

0

y

: Press to increase or

decrease the volume.

!

CONTENT: This function enables

you to view the Content Library.

@

MEDIA.P: Allows you to play

music files, pictures, and movies.

#

INFO: Press to display

information on the TV screen.

$

Use these buttons in the Media

Play and Anynet

+

modes. (

∏

:

This remote can be used to

control recording on Samsung

recorders with the Anynet

+

feature)

%

ON/OFF

@

: Pressing the

ON/OFF

@

light button toggles

between on and off. When the

remote control is on, and a button

is pressed on the remote control,

the remote control buttons will

be lit for a moment. (Using the

remote control with the ON/OFF

@

light button set to On will

reduce the battery usage time.)

^

PRE-CH : Enables you to return

to the previous channel you were

watching.

&

MENU : Displays the main on-

screen menu.

*

FAV.CH : Press to switch to your

favorite channels.

(

RETURN : Returns to the

previous menu

)

 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

E

: Use to

select on-screen menu items and

change menu values.

a

EXIT : Press to exit the menu.

b

z

: Press to change

channels.

c

MUTE

M

: Press to temporarily

cut off the sound.

d

P.SIZE: Picture size selection.

e

MTS: Press to choose stereo,

mono or Separate Audio Program

(SAP broadcast).

f

CC: Controls the caption

decoder.

¦

N

1

3

4

5

6

7

8

0

@

#

$

9

!

2

%

^

*

(

a

b

c

d

f

e

)

&

[750-NA]BN68-02111B-Eng.indb 4 2009-03-30 �� 1:42:44

English - 5

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the

figure.

2.

Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the

diagram inside the compartment.

3.

Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t

be using the remote control for a long time. (Assuming typical TV

usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

Is the TV power on?

Are the plus and minus ends of the batteries reversed?

Are the batteries drained?

Is there a power outage or is the power cord unplugged?

Is there a special fluorescent light or neon sign nearby?

Viewing the menus

Before using the TV, follow the steps below to learn how to navigate the menu in order to select and adjust different functions.

Operation the OSD (On Screen Display)

The access step may differ depending on the selected menu.

1.

Press the MENU button.

2.

The main menu appears on the screen. The menu’s left side has icons : Picture, Sound,

Channel, Setup, Input, Application, Support.

3. Press the ▲ or ▼ button to select one of the icons.

¦

N



¦

❑

MENU Button

Display the main on-screen menu.

ENTER

E

/ DIRECTION Button

Move the cursor and select an item. Select

the currently selected item. Confirm the

setting.

RETURN Button

Return to the previous menu.

EXIT

Exit the on-screen menu.

Mode :Standard ▶

Backlight :7

Contrast :95

Brightness :45

Sharpness :50

Color :50

Tint(G/R) :G50/R50

AdvancedSettings

Picture

[750-NA]BN68-02111B-Eng.indb 5 2009-03-30 �� 1:42:45

English - 6

4. Then press the ENTER

E

button to access the icon’s sub-menu.

5.

Press the ▲ or ▼ button to select the icon’s submenu.

6.

Press the ◄ or ► button to decrease or increase the value of a particular item. The

adjustment OSD may differ depending on the selected menu.

7.

Press the ENTER

E

button to complete the configuration. Press the EXIT button to exit.

Mode :Standard

Backlight :7 ▶

Contrast :95

Brightness :45

Sharpness :50

Color :50

Tint(G/R) :G50/R50

AdvancedSettings

PictureOptions

Picture

7

U

Move

L

Adjust

E

Enter

R

Return

▲

Backlight

▼

Help icon

[750-NA]BN68-02111B-Eng.indb 6 2009-03-30 �� 1:42:45

English - 7

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

1.

Press the POWER

P

button on the remote control.

You can also use the POWER

P

button on the TV.

The message Select Language of the OSD. is displayed.

2.

Press the ENTER

E

button. Press the ▲ or ▼ button to select the language, then press

the ENTER

E

button. The message Select ‘Home Use’ when installing this TV in

your home. is displayed.

3.

Press the ◄ or ► button to select Store Demo or Home Use, then press the ENTER

E

button. The message Select the Antenna source to memorize. is displayed.

We recommend setting the TV to Home Use mode for the best picture in your home

environment.

Store Demo mode is only intended for use in retail environments.

If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the volume

button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

4.

Press the ▲ or ▼ button to memorize the channels of the selected connection. Press the ENTERE button to select Start.

Air: Air antenna signal. / Cable: Cable antenna signal. / Auto: Air and Cable antenna signals.

In Cable mode, you can select the correct signal source among STD, HRC, and IRC by pressing the ▲, ▼, ◄ or ►

button, then press the ENTER

E

button. If you have Digital cable, select the cable system signal source for both Analog

and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.

5.

Press the ENTER

E

button to select Start. The TV will begin memorizing all of the available channels.

To stop the search before it has finished, press the ENTER

E

button with Stop selected.

After all the available channels are stored, it starts to remove scrambled channels. The Auto program menu then

reappears. Press the ENTER

E

button when channel memorization is complete. The message Set the Clock Mode. is

displayed.

6.

Press the ENTER

E

button. Press the ▲ or ▼ button to select Auto, then Press the ENTER

E

button. The message Set to

daylight saving time. is displayed. If you select Manual, Set current date and time. is displayed.

7.

Press the ▲ or ▼ button to select Off, On or Auto, then press the ENTER

E

button.

8.

Press the ▲ or ▼ button to highlight the time zone for your local area. Press the ENTER

E

button. If you have received a

digital signal, the time will be set automatically. If not, refer to the ‘Setting the Time’ instructions to set the clock.

(see pages 28~29)

9.

The description for the connection method providing the best HD screen quality is displayed. Check the description and press

the ENTER

E

button.

10.

Press the ◄ or ► button to select See Product Guide or Watch TV. Press the ENTER

E

button.

See Product Guide: You are moved to the Product Guide where you can view the introduction to the main functions of

your new HDTV.

Watch TV: You can watch the memorized channels.

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,

then press the ENTER

E

button.

2.

Press the ENTER

E

button again to select Plug & Play.

The Plug & Play feature is only available in the TV mode.

¦

N



N

Plug&Play  ▶

Language :English

Time

GameMode :Off

BDWise :On

NetworkType :Cable

NetworkSetup

V-Chip

Setup

SelectLanguageoftheOSD.

Language :English  ▶

E

Enter

Plug&Play

[750-NA]BN68-02111B-Eng.indb 7 2009-03-30 �� 1:42:45

English - 8

CONNECTIONS

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see ‘Antennas with 300

Ω Flat Twin Leads’ below.

If your antenna has one lead that looks like the diagram to the right, see ‘Antennas with 75 Ω

Round Leads’.

If you have two antennas, see ‘Separate VHF and UHF Antennas’.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or ‘rabbit ears’) that has 300Ω twin

at leads, follow the directions below.

1.

Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2.

Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine

the two antenna signals before connecting the antennas to the TV. This procedure requires an

optional combiner-adaptor (available at most electronics shops).

1.

Connect both antenna leads to the combiner.

2.

Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

¦

ANT IN

UHF

VHF

ANT IN

UHF

VHF

[750-NA]BN68-02111B-Eng.indb 8 2009-03-30 �� 1:42:46

English - 9

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled ‘ANT OUT’, ‘VHF OUT’ or simply, ‘OUT’.

2.

Connect the other end of this cable to the ANT IN terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

This terminal might be labeled ‘ANT IN’, ‘VHF IN’ or simply, ‘IN’.

2.

Connect this cable to a two-way splitter.

3.

Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

4.

Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5.

Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6.

Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

After you have made this connection, set the A/B switch to the ‘A’ position for normal viewing. Set the A/B switch to the ‘B’

position to view scrambled channels. (When you set the A/B switch to ‘B’, you will need to tune your TV to the cable box’s

output channel, which is usually channel 3 or 4.)

¦

N

ANT IN

ANT IN ANT OUT

ANT IN

Splitter

Cable Box

Incoming cable

TV Rear

ANT IN

RF (A/B) Switch

[750-NA]BN68-02111B-Eng.indb 9 2009-03-30 �� 1:42:46

English - 10

Viewing the Connection Panel

The product color and shape may vary depending on the model.

Rear Panel

1 POWER INPUT

Connects the supplied power cord.

The location of the POWER INPUT may be different depending on its model.

2 HDMI IN 1(DVI), 2, 3 / DVI AUDIO IN [R-AUDIO-L]

Connects to the HDMI jack of a device with an HDMI output.

No sound connection is needed for an HDMI to HDMI connection.

What is HDMI?

HDMI(High-Definition Multimedia Interface), is an interface that enables the transmission of digital audio and video

signals using a single cable.

The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth

Digital Copy Protection) coding feature installed.

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI

cable and there is no sound, connect the HDMI cable to the HDMI IN 1(DVI) jack and the audio cables to the DVI AUDIO

IN [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-ray player /

Cable Box / Satellite receiver (Set-Top Box) to confirm the HDMI version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying flicker or no screen display.

Use the HDMI IN 1(DVI) jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter

(DVI to HDMI) for video connection and the DVI AUDIO IN [R-AUDIO-L] jacks for audio. When using an HDMI / DVI cable

connection, you must use the HDMI IN 1(DVI) jack.

3 ANT IN

Connects to an antenna or cable TV system.

¦

N



N

1

3

2

Cable Television

Network

or

[750-NA]BN68-02111B-Eng.indb 10 2009-03-30 �� 1:42:46

English - 11

4 KENSINGTON LOCK

The Kensington Lock (optional) is a device used to physically fix the system when used in a public place. If you want to use a

locking device, contact the dealer where you purchased the TV.

The location of the Kensington Lock may be different depending on its model.

5 COMPONENT IN 1, 2 / AV IN 1

Connects Component video / audio.

The COMPONENT IN 1 jack is also used as the AV IN 1 jack.

Connect the video cable to the COMPONENT IN 1 [Y/VIDEO] jack and the audio cable to the COMPONENT IN 1 [R-

AUDIO-L] jacks.

If you have a ‘mono’ (non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks

of the TV. Alternatively, connect the cable to the ‘R’ jack. If your VCR is stereo, you must connect two cables.

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not match the color of the video cable

(Yellow).

6 PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

If your PC supports an HDMI connection, you can connect this to the HDMI IN 1(DVI), 2, 3 or 4 terminal.

If your PC supports a DVI connection, you can connect this to the HDMI IN 1(DVI) / DVI AUDIO IN [R-AUDIO-L] terminal.

7 DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component such as a Home theater receiver.

When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack: Decrease the volume of the TV

and adjust the volume level with the system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

When the Home Theater receiver is set to On, you can hear sound output from the TV’s Optical jack. When the TV is

displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a

digital component such as a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) and is connected to the

TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio,

connect the digital audio out jack on DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) directly to an

Amplifier or Home Theater, not the TV.

N

5

6

7

R

G

Y

BWR

WR

4

or

[750-NA]BN68-02111B-Eng.indb 11 2009-03-30 �� 1:42:47

English - 12

8 EX-LINK

Connector for service only.

9 AUDIO OUT

Connects to the audio input jacks on your Amplifier/Home theater.

When an audio amplifier is connected to the AUDIO OUT [R-AUDIO-L] jacks: Decrease the volume of the TV and adjust

the volume level with the Amplifier’s volume control.

0 LAN

Connect a LAN cable to this port to connect to the Network.

Side Panel

For devices frequently connected/disconnected from your TV, it is convenient to use the jacks on the side of your TV (e.g.

Camcorder).

1 USB1(HDD) / USB2

Connector for software upgrades and Media Play, etc. You can connect to Samsung’s network wirelessly using the ‘Samsung

Wireless LAN Adapter’ (Sold separately).

For USB HDD, use the USB1(HDD) port.

2 HDMI IN 4

Connect to the HDMI jack of a device with HDMI output.

3 AV IN 2 [VIDEO] / [R-AUDIO-L]

Video and audio inputs for external devices, such as a camcorder or VCR.

N

8

0

9

YWR

Y

W

R

1

2

3

[750-NA]BN68-02111B-Eng.indb 12 2009-03-30 �� 1:42:47

English - 13

CHANNEL

You can congure various settings for your TV channels with features such as Auto Program, Favorite Channels, and Signal

Strength.

Channel Menu

Antenna→Air/Cable

Before your television can begin memorizing the available channels, you must specify the type

of signal source that is connected to the TV (i.e. an Air or a Cable system).

Press the TOOLS button to display the Tools menu. You can also set the Antenna by

selecting Tools→SwitchtoCable (or Switch to Air).

Auto Program

Air: Air antenna signal. / Cable: Cable antenna signal. / Auto: Air and Cable antenna

signals

When selecting the Cable TV system: Selects the cable system. STD, HRC and IRC identify various types of cable TV

systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point

the signal source has been selected.

After all the available channels are stored, it starts to remove scrambled channels (Removing scrambled channel). The Auto

program menu then reappears.

If you want to stop Auto Programming, press the ENTER

E

button. The Stop Auto Program? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTER

E

button.

Clear Scrambled Channel (digital channels only)

This function is used to lter out scrambled channels after Auto Program is completed. This process may take up to 20~30

minutes.

To stop searching scrambled channels: Press the ENTER

E

button to select Stop. Press the ◄ button to select Yes, then

press the ENTER

E

button.

This function is only available in Cable mode.

Channel List

For detailed procedures on using the Channel List, refer to the ‘Managing Channels’ instructions. (see pages 14~15)

You can select these options by simply pressing the CH LIST button on the remote control.

Fine Tune (analog channels only)

Use ne tuning to manually adjust a particular channel for optimal reception.

If you do not store the fine-tuned channel in memory, adjustments are not saved.

‘*’ will appear next to the name of fine-tuned channels.

To reset the fine tuning setting, press the ▼ button to select Reset, then press the ENTER

E

button.

¦

❑

T

❑

■

N

❑

N

❑

O

❑

N

Antenna :Air ▶

AutoProgram

ClearScrambledChannel

ChannelList

FineTune

Channel

[750-NA]BN68-02111B-Eng.indb 13 2009-03-30 �� 1:42:48

English - 14

Managing Channels

Using this menu, you can add / delete or set favorite channels and use the program guide for

digital broadcasts.

All Channels

Shows all currently available channels.

Added Channels

Shows all added channels.

Favorite

Shows all favorite channels.

To select the favorite channels you have set up, press the FAV.CH button on the remote control.

Programmed

Shows all current reserved programs.

Select a channel in the All Channels, Added Channels or Favorite screen by pressing the ▲ / ▼ buttons, and pressing the

ENTER

E

button. Then you can watch the selected channel.

Using the color buttons with the Channel List

Red (Antenna): Switches to Air or Cable.

Green (Zoom): Enlarges or shrinks a channel number.

Yellow (Select): Selects multiple channel lists. You can perform the add/delete or add to Favorite/delete from Favorite

function for multiple channels at the same time. Select the required channels and press the yellow button to set all the

selected channels at the same time. The

c

mark appears to the left of the selected channels.

TOOLS (Tools): Displays the Add (or Delete), Add to Favorite (or Delete from Favorite), Timer Viewing, Channel

Name Edit, Select All (or Deselect All) and Auto Program menus (The Options menus may differ depending on the

situation.)

Channel Status Display Icons

c

: A channel selected by pressing the yellow button.

(

: A program currently being broadcast.

*

: A channel set as a Favorite.

)

: A reserved program.

Channel List Option Menu (in All Channels / Added Channels / Favorite)

Press the TOOLS button to use the option menu.

Option menu items may differ depending on the channel status.

Add / Delete

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on the All Channels menu.

A gray-colored channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel from the Added Channels or Favorite menu in the same

manner.

¦

■

O

■

N



N

■

N

AllChannels

2  Air

4  Air

4-2

*

TV#8

8  Air

13  Air

13-1

*

TV#3 Alice’sAdventuresinWonderland

Air Antenna Zoom Select

T

Tools

Delete

AddtoFavorite

TimerViewing

ChannelNameEd

SelectAll

AutoProgram

AddedChannels

2  Air

4  Air

4-2

*

TV#8

8  Air

13  Air

13-1

*

TV#3 Alice’sAdventuresinWonderland

Air Antenna Zoom Select

T

Tools

[750-NA]BN68-02111B-Eng.indb 14 2009-03-30 �� 1:42:48

English - 15

Add to Favorite / Delete from Favorite

You can set channels you watch frequently as Favorite.

Press the TOOLS button to display the Tools menu. You can also set the add to (or delete from) Favorites by selecting Tools

→AddtoFavorite (or Delete from Favorite).

The ‘

*

’ symbol will be displayed and the channel will be set as a favorite.

All favorite channels will be shown on Favorite menu.

Timer Viewing

If you reserve a program you want to watch, the channel is automatically switched to the reserved channel in the Channel List;

even when you are watching another channel. To reserve a program, set the current time first.

Only memorized channels can be reserved.

You can set the channel, day, month, year, hour and minute directly by pressing the number buttons on the remote control.

Reserving a program will be shown in the Programmed menu.

Digital Program Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Program Guide for the channel appears. You can reserve

a program according to the procedures described above.

Channel Name Edit (analog channels only)

Channels can labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Select All / Deselect All

Select All: You can select all the channels in the channel list.

Deselect All: You can deselect all the selected channels.

You can only select Deselect All when there is a selected channel.

Auto Program

For detailed procedures on using the Auto Program, refer to the ‘Channel Menu’ instructions. (see page 13)

Channel List Option Menu (in Programmed)

You can view, modify or delete a reservation.

Press the TOOLS button to use the option menu.

Change Info

Select to change a viewing reservation.

Cancel Schedules

Select to cancel a viewing reservation.

Information

Select to view a viewing reservation.

(You can also change the reservation information.)

Select All

Select all reserved programs.

■

T

N

■

N

■

N

■

●

N

■

N

■

Programmed

1/1/2009

1:595TV1

)



2:592TV3

)

TheEqualizer

3:592TV3

)

McMillan&Wife

4:592TV3

)

M.Spillane’smike

Air Antenna Zoom Select

T

Tools

E

Information

ChangeInfo

CancelSchedules

Information

SelectAll



[750-NA]BN68-02111B-Eng.indb 15 2009-03-30 �� 1:42:48

English - 16

PICTURE

You can congure various picture options such as the picture mode, aspect ratio, and color to suit your personal preferences.

Configuring the Picture Menu

Mode

You can select the type of picture which best corresponds to your viewing requirements.

Press the TOOLS button to display the Tools menu. You can also set the picture mode by

selecting Tools→PictureMode.

Dynamic

Selects the picture for increased definition in a bright room.

Standard

Selects the picture for the optimum display in a normal environment.

Natural

Selects the picture for an optimum and eye-comfortable display.

Natural is not available in PC mode.

Movie

Selects the picture for viewing movies in a dark room.

Backlight / Contrast / Brightness / Sharpness / Color / Tint(G/R)

Your television has several setting options that allow you to control the picture quality.

Backlight: Adjusts the brightness of LCD back light.

Contrast: Adjusts the contrast level of the picture.

Brightness: Adjusts the brightness level of the picture

Sharpness: Adjusts the edge definition of the picture.

Color: Adjusts color saturation of the picture.

Tint(G/R): Adjusts the color tint of the picture.

When you make changes to Backlight, Contrast, Brightness, Sharpness, Color or Tint(G/R) the OSD will be adjusted

accordingly.

In PC mode, you can only make changes to Backlight, Contrast and Brightness.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

The energy consumed during use can be signicantly reduced if the brightness level of the picture is lowered, which will

reduce the overall running cost.

Advanced Settings

Samsung’s new TVs allow you to make even more precise picture settings than previous

models.

Advanced Settings is available in Standard or Movie mode.

In PC mode, you can only make changes to Dynamic Contrast, Gamma and White

Balance from among the Advanced Settings items.

BlackTone→Off/Dark/Darker/Darkest

You can select the black level on the screen to adjust the screen depth.

¦

❑

T

■

N

■

❑

●

N

❑

N

■

Mode :Standard ▶

Backlight :7

Contrast :95

Brightness :45

Sharpness :50

Color :50

Tint(G/R) :G50/R50

AdvancedSettings

Picture

7

U

Move

L

Adjust

E

Enter

R

Return

▲

Backlight

▼

BlackTone :Off  ▶

DynamicContrast :Medium

Gamma :0

ColorSpace :Native

WhiteBalance

FleshTone :0

EdgeEnhancement :On

U

Move

E

Enter

R

Return

AdvancedSettings

[750-NA]BN68-02111B-Eng.indb 16 2009-03-30 �� 1:42:48

English - 17

DynamicContrast→Off/Low/Medium/High

You can adjust the screen contrast so that the optimal contrast is provided.

Gamma

You can adjust the primary color (red, green, blue) intensity.

Color Space

Color space is a color matrix composed of red, green and blue colors. Select your favorite color space to experience the most

natural color.

Auto: Auto color space automatically adjusts to the most natural color tone based on program sources.

Native: Native color space offers deep and rich color tone.

Custom: Adjusts the color range to suit your preference.

Changing the adjustment value will refresh the adjusted screen.

Settings can be adjusted and stored for each external device you have connected to an input of the TV. For example, if

you have a DVD player connected to HDMI 1 and it is currently selected, settings and adjustments will be saved for the

DVD player.

Color: Red, Green, Blue, Yellow, Cyan or Magenta

Color is available when Color Space is set to Custom.

In Color, you can adjust the RGB values for the selected color.

To reset the adjusted RGB value, select Reset.

Red: Adjusts the red saturation level of the selected color.

Green: Adjusts the green saturation level of the selected color.

Blue: Adjusts the blue saturation level of the selected color.

Reset: Resets the color space to the default values.

White Balance

You can adjust the color temperature for more natural picture colors.

R-Offset: Adjusts the red color darkness.

G-Offset: Adjusts the green color darkness.

B-Offset: Adjusts the blue color darkness.

R-Gain: Adjusts the red color brightness.

G-Gain: Adjusts the green color brightness.

B-Gain: Adjusts the blue color brightness.

Reset: The previously adjusted white balance will be reset to the factory defaults.

Flesh Tone

You can emphasize the pink ‘flesh tone’ in the picture.

Changing the adjustment value will refresh the adjusted screen.

EdgeEnhancement→Off/On

You can emphasize object boundaries in the picture.

xvYCC→Off/On

Setting the xvYCC mode to on increases detail and color space when watching movies from an external device (ie. DVD player)

connected to the HDMI or Component IN jacks.

xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.

■

●

N



N



■

●

■

N

■

N

[750-NA]BN68-02111B-Eng.indb 17 2009-03-30 �� 1:42:48

English - 18

Picture Options

In PC mode, you can only make changes to the Color Tone and Size from among the

items in Picture Options.

ColorTone→Cool/Normal/Warm1/Warm2/Warm3

Warm1, Warm2 or Warm3 is only activated when the picture mode is Movie.

Settings can be adjusted and stored for each external device you have connected to an

input of the TV.

Size

Occasionally, you may want to change the size of the image on your screen. Your TV comes

with several screen size options, each designed to work best with specific types of video input. Your cable box/satellite receiver

may have its own set of screen sizes as well. In general, though, you should view the TV in 16:9 mode as much as possible.

Alternately, you can press the P.SIZE button on the remote control repeatedly to change the picture size.

16:9 : Sets the picture to 16:9 wide mode.

Zoom1: Magnifies the size of the picture on the screen.

Zoom2: Magnifies the size of the picture more than Zoom1.

Wide Fit: Enlarges the aspect ratio of the picture to fit the entire screen.

4:3 : Sets the picture to 4:3 normal mode.

Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p), Component

(1080i/1080p) or DTV (1080i) signals are input.

16:9 Zoom1 Zoom2

Wide Fit 4:3 Screen Fit

When Double (

Œ

,

À

) mode has been set in PIP, the Picture Size cannot be set.

Temporary image retention may occur when viewing a static image on the set for more than two hours.

After selecting Zoom1, Zoom2 or Wide Fit: Press the ► button to Select Position, then press the ENTER

E

button. Press

the ▲ or ▼ button to move the picture up and down. Then press the ENTER

E

button. Press the ► button to Select Size,

then press the ENTER

E

button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then

press the ENTER

E

button.

After selecting Screen Fit in HDMI (1080i/1080p) or Component (1080i/1080p) mode, you made need to center the picture:

Press the ◄ or ► button to select Position, then press the ENTER

E

button. Press the ▲, ▼, ◄ or ► button to move the

picture.

Reset: Press the ◄ or ► button to select Reset, then press the ENTER

E

button. You can initialize the setting.

HD (High Definition): 16:9 - 1080i/1080p (1920x1080), 720p (1280x720)

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Input Source Picture Size

ATV, AV, Component (480i, 480p) 16:9, Zoom1, Zoom2, 4:3

DTV(1080i), Component (1080i, 1080p),

HDMI (720p, 1080i, 1080p)

16:9, 4:3, Wide Fit, Screen Fit

PC 16:9, 4:3

❑

N

■

N

■

O

●

N



N

ColorTone :Normal  ▶

Size :16:9

DigitalNR :Auto

HDMIBlackLevel :Normal

FilmMode :Off

BlueOnlyMode :Off

AutoMotionPlus240Hz :Standard

U

Move

E

Enter

R

Return

PictureOptions

16:9

Zoom2

U

MoveZoom1

U

Move

Screen Fit4:3

Wide Fit

U

Move

[750-NA]BN68-02111B-Eng.indb 18 2009-03-30 �� 1:42:49

La page charge ...

Samsung LN40B750 Manuel utilisateur

Ce manuel convient également à

Samsung LN40B750 Manuel utilisateur

dans d''autres langues

Documents connexes