Samsung DV405ETPAWR Manuel utilisateur

Gas and Electric Dryer

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory

parts,

please register your product at or

contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV405*

DV395*

DV393*

DV398*

This manual is made with 100% recycled paper.

DV405ETPAWR_03021F-08_EN_130820.indd 1DV405ETPAWR_03021F-08_EN_130820.indd 1 2013-08-20  3:13:532013-08-20  3:13:53

2_ Features

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra

large 7.4 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for

a wrinkle-free result.

2. Smart Care (DV405* Only)

Samsung’s Smart Care, an automatic error-monitoring system, detects and diagnoses

problems at an early stage and provides quick and easy solutions.

3. Steam cycle

This cycle sprays a small amount of water into the dryer drum after several minutes of

tumbling with heat. It reduces bad odors from clothing that are difficult to remove when

washing with water, and also reduces wrinkles.

4. Sanitize Cycle

This cycle sanitizes garments by infusing high temperature heat deep into the fabric during

the drying cycle and eliminating 99.9% of certain bacteria. Use this cycle for clothing,

bedding, towels, or other items needing sanitization.

5. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 13 automatic drying cycles, including normal,

heavy duty and towels, or let the Fuzzy Logic Control measure the degree of dampness and

automatically set the drying time. Precision drying has never been easier than with Samsung.

6. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in

less time... just 42 minutes! Giving you time for more important things in life.

7. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.01 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most efficient way.

8. Easy Reversible Door

Our dryers will fit just about anywhere. The direction of our easy reversible door can be

changed easily and quickly.

9. Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It

also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent

10. Stacking (MODEL NO: SK-5A)

Samsung’s Washers and Dryers can be stacked to maximize usable space.

The Dryer legs need to be removed to stack the Washer and Dryer. You can purchase an

optional stacking kit from your Samsung retailer.

11. 4-way Vent (Electric model only, MODEL NO : DV-1A)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

An optional 4-way Vent kit is available for purchase from your Samsung retailer.

DV405ETPAWR_03021F-08_EN_130820.indd Sec9:2DV405ETPAWR_03021F-08_EN_130820.indd Sec9:2 2013-08-20  3:13:572013-08-20  3:13:57

Safety information _3

SAVE THESE INSTRUCTIONS

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

WARNING

Hazards or unsafe practices that may result in severe personal injury or

death.

Follow the information in this manual to minimize the risk of fire or explosion or

to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near this or

any other appliance.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

• To reduce the risk of severe injury or death, follow all installation instructions.

WARNING - Risk of Fire

DV405ETPAWR_03021F-08_EN_130820.indd Sec1:3DV405ETPAWR_03021F-08_EN_130820.indd Sec1:3 2013-08-20  3:13:572013-08-20  3:13:57

4_ Safety information

SAVE THESE INSTRUCTIONS

safety instructions

IMPORTANT SAFTY INSTRUCTION

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off

vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance, such as

vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing

wax or chemicals, such as mops and cleaning cloths. Flammable substances may cause the

fabric to catch fire by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any other

appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is necessary

when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the drying

compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with controls.

10. Do not repair or replace any part of the appliance or attempt any servicing unless specifically

recommended in the user-maintenance instructions or in published userrepair instructions that

you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by qualified service

personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils

may contribute to a chemical reaction that could cause a load to catch fire.

17. This appliance must be grounded. See “Electrical requirements” and “Grounding” in installing your

dryer section.

State of California Proposition 65 Warnings:

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to

publish a list of substances known to the State of California to cause cancer, birth defects, or other

reproductive harm, and requires businesses to warn of potential exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth defects, or

other reproductive harm. This appliance can cause low-level exposure to some of the substances

listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including benzene,

formaldehyde, carbon monoxide, and soot; as a result of possible incomplete combustion of natural

gas or LP fuels. Exposure to these substances can be minimized further by properly venting the dryer

to the outdoors.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec1:4DV405ETPAWR_03021F-08_EN_130820.indd Sec1:4 2013-08-20  3:13:572013-08-20  3:13:57

Safety information _5

SAVE THESE INSTRUCTIONS

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

Read all instructions before using the appliance.

To reduce the risk of fire or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifically

recommended in the user-repair instructions and you understand and have the skills to

carry those out.

Do not use fabric softeners or products to eliminate static unless recommended for dryer

use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and

dirt.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec1:5DV405ETPAWR_03021F-08_EN_130820.indd Sec1:5 2013-08-20  3:13:582013-08-20  3:13:58

6_ Safety information

SAVE THESE INSTRUCTIONS

safety instructions

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See

installation instructions for grounding this appliance.

Do not sit on top of the dryer.

Because of continuing product improvements, Samsung reserves the right to change

specifications without notice. For complete details, see the Installation Instructions

packed with your product before selecting cabinetry, making cutouts, or beginning

installation.

Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie.

coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

Gas leaks may occur in your system, resulting in a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or

cooking oil. Even after being washed, these items may contain significant amounts of these

oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec1:6DV405ETPAWR_03021F-08_EN_130820.indd Sec1:6 2013-08-20  3:13:582013-08-20  3:13:58

Installing your dryer _7

contents

INSTALLING YOUR DRYER

8

8 installation requirements

8 The dryer exterior

9 Ducting requirements

10 Important to installer

10 Location considerations

11 Alcove or closet installation

13 Exhausting

14 Gas requirements

15 Electrical requirements

15 Grounding

16 Electrical connections

17 Replacement parts and accessories

17 Tools Needed For Installation

18 Installation - General procedure

20 Final installation checklist

21 Dryer Exhaust Tips

22 Door Reversal

23 Connecting the inlet hose

OPERATING INSTRUCTIONS, TIPS

24

24 Overview of the control panel

26 Child lock

27 Drum Light

27 Delay Start

27 My cycle

28 Vent Sensor

29 Smart Care

30 Rack Dry

31 Clean the lint filter

31 Load the dryer properly

31 Getting started

CARE AND CLEANING

32

32 Control Panel

32 Tumbler

32 Stainless Steel Tumbler

32 Dryer Exterior

32 Dryer Exhaust System

SPECIAL LAUNDRY TIPS

33

33 Special laundry tips

TROUBLESHOOTING

34

34 Check these points if your dryer…

35 Information codes

APPENDIX

36

36 Fabric care chart

37 Protecting the environment

37 Declaration of conformity

37 Specifications

38 Cycle chart

DV405ETPAWR_03021F-08_EN_130820.indd Sec3:7DV405ETPAWR_03021F-08_EN_130820.indd Sec3:7 2013-08-20  3:13:582013-08-20  3:13:58

8_ installing your dryer

installing your dryer

INSTALLATION REQUIREMENTS

Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup,

adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are

responsible.

Make sure you have everything necessary for proper installation.

1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

2. A POWER CORD for electric dryers (except Canada).

3. GAS LINES (if you have a gas dryer) must meet national and local codes.

4. EXHAUST SYSTEM – must be rigid metal or flexible stiff-walled metal exhaust ducting.

See the exhaust requirements on pages 8-10.

THE DRYER EXTERIOR

INCLUDED ACCESORIES

“Y”-connector Short inlet hose Rubber Washer Long inlet hose

Adjustable legs

Control panel

Door

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:8DV405ETPAWR_03021F-08_EN_130820.indd Sec5:8 2013-08-20  3:13:582013-08-20  3:13:58

installing your dryer _9

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

• Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

• Only a rigid or flexible metal duct should be used for exhausting.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF

A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY.

THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.

• Do not use plastic flexible duct. Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend

drying times, and affect dryer operation.

• Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10.16 cm) 2.5” (6.35 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 24.4 m (80 ft.) 12.4 m (41 ft.) 22.6 m (74 ft.) 10.1 m (33 ft.)

1 20.7 m (68 ft.) 11.2 m (37 ft.) 18.9 m (62 ft.) 8.8 m (29 ft.)

2 17.4 m (57 ft.) 10.1 m (33 ft.) 15.5 m (51 ft.) 7.6 m (25 ft.)

3 14.3 m (47 ft.) 9.0 m (29 ft.) 12.5 m (41 ft.) 6.5 m (21 ft.)

* Do not use non-metallic flexible duct.

01 installing your dryer

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:9DV405ETPAWR_03021F-08_EN_130820.indd Sec5:9 2013-08-20  3:13:582013-08-20  3:13:58

10_ installing your dryer

installing your dryer

If the new dryer is installed into an existing exhaust system you must make

sure:

• The exhaust system meets all local, state, and national codes.

• That a flexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD

SUFFOCATING.

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the dryer, and enough

space behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the

bottom or the right or the left, use the accessory exhaust kit. Instructions are included with the kit. It’s

important to make sure the room has enough fresh air. The dryer must be located where there is no air-flow

obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO

WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS,

GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE

LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:10DV405ETPAWR_03021F-08_EN_130820.indd Sec5:10 2013-08-20  3:13:582013-08-20  3:13:58

installing your dryer _11

ALCOVE OR CLOSET INSTALLATION

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm

Rear – 5 in / 127 mm

Top – 17 in / 432 mm

Closet Front – 2 in / 51 mm

If the washer and dryer are installed together, the closet front must have at least a 72 in²

(465 cm²) unobstructed air opening.

A. Recessed area

B. Side view - closet or confined area

01 installing your dryer

B

2 in.

(5 cm)

31.9 in.

(81.1 cm)

5 in.

(12.7cm)

17 in.

(43.2 cm)

A

1 in.

(2.5 cm)

27 in.

(68.6 cm)

1 in.

(2.5 cm)

1 in.

(2.5 cm)

27 in.

(68.6 cm)

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:11DV405ETPAWR_03021F-08_EN_130820.indd Sec5:11 2013-08-20  3:13:582013-08-20  3:13:58

12_ installing your dryer

installing your dryer

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal

Required Dimensions for Installation With Stacking Kit

341.1 in.

(86.5 cm)

5 in.

(12.7 cm)

51.7 in. (131.4 cm) to clear open door

27 in.

(68.6 cm)

39 in.

(99.1 cm)

53.6 in.

(136.2 cm)

31.9 in.

(81.1 cm)

3 in.

(7.6 cm)

Closet or Door

48 in.² *

(310 cm²)

3 in.

(7.6 cm)

24 in.² *

(155 cm²)

1 in.

(2.5 cm)

8 in.**

(20.3 cm)

5 in.

(12.7 cm)

6 in. *

(15.2 cm)

1 in.

(2.5 cm)

78 in.

(198.1 cm)

27 in.

(68.6 cm)

* Required spacing

** External exhaust elbow requires

additional space.

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:12DV405ETPAWR_03021F-08_EN_130820.indd Sec5:12 2013-08-20  3:13:592013-08-20  3:13:59

installing your dryer _13

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a

building.

Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room.

In the United States:

• All dryer must be exhausted to the outside.

• The required exhaust duct is 4 inches(10.2 cm ) in diameter.

• Use only those foil-type flexible ducts, if any, specifically indentified for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A, shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and

number of bends.

• The total length of flexible metal duct shall not exceed 2.4m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

In Canada:

• All dryer must be exhausted to the outside.

• The exhaust duct should be 4 inches(10.2 cm ) in diameter.

• Use only those foil-type flexible ducts, if any, specifically indentified for use with the appliance

by the manufacturer shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and

number of bends.

• The total length of flexible metal duct shall not exceed 2.4m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

Outside the U.S. and Canada:

• Refer to the local codes.

The dryer must be exhausted to the outside to reduce the risk of fire when installed in an

alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

01 installing your dryer

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:13DV405ETPAWR_03021F-08_EN_130820.indd Sec5:13 2013-08-20  3:13:592013-08-20  3:13:59

14_ installing your dryer

installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

Commonwealth of Massachusetts installation instructions

Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve

must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install

your dryer, the connector must have a maximum length of 3’ (36”).

- Gas leaks may occur in your system, creating a dangerous situation.

- Gas leaks may not be detected by smell alone.

- Gas suppliers recommend you purchase and install a UL-approved gas detector.

- Install and use in accordance with the manufacturer’s instructions.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:14DV405ETPAWR_03021F-08_EN_130820.indd Sec5:14 2013-08-20  3:13:592013-08-20  3:13:59

installing your dryer _15

ELECTRICAL REQUIREMENTS

The wiring diagram is located on the back of the dryer.

• Improperly connecting the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet,

have a proper outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT

WATER PIPES.

Electric models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold

separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the dryer.

01 installing your dryer

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:15DV405ETPAWR_03021F-08_EN_130820.indd Sec5:15 2013-08-20  3:13:592013-08-20  3:13:59

16_ installing your dryer

installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. The electric

service requirements can be found on the data label located behind the door. A 30-ampere fuse

or circuit breaker on both sides of the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

Risk of Electric Shock:

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be supported at the dryer cabinet by a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA

type 14-30R.)

Electric models – Canada Only

• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:16DV405ETPAWR_03021F-08_EN_130820.indd Sec5:16 2013-08-20  3:13:592013-08-20  3:13:59

installing your dryer _17

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your

dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

TOOLS NEEDED FOR INSTALLATION

Gather the required tools and parts before starting the installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts

Pliers Cutting knife Pipe wrench (gas only) Nut drivers

Level Phillips Screwdriver Duct tape Wrench

01 installing your dryer

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:17DV405ETPAWR_03021F-08_EN_130820.indd Sec5:17 2013-08-20  3:13:592013-08-20  3:13:59

18_ installing your dryer

installing your dryer

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page . When done, return to

Step 3 below.

3. Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

b. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

The pipe joint compound must be resistant to the action of any liquefied petroleum gas.

c. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm)

female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line fitting over the threads.

e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

f. Go to Step 6 on the next page

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:18DV405ETPAWR_03021F-08_EN_130820.indd Sec5:18 2013-08-20  3:14:002013-08-20  3:14:00

installing your dryer _19

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step

7) or 4 Wire system instructions (Step 8) below.

7. Three Wire system instructions:

A. External ground connector

B. Neutral grounding wire (green/yellow)

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. ¾” (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap

to the terminal block support to ground the dryer frame to the neutral conductor.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

8. Four Wire System instructions:

A. External ground connector

B. Green or bare copper wire of power cord

C. ¾” (1.9 cm) UL-listed strain relief

D. Center silver-colored terminal block screw

E. Neutral Grounding wire (green/yellow)

F. Neutral wire (white or center wire)

1. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the

power cord to the external ground connector screw. If

you want to connect B (Green or bare copper wire of

power cord) to the Neutral Post without assembling with A

(cabinet ground), call the service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

01 installing your dryer

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:19DV405ETPAWR_03021F-08_EN_130820.indd Sec5:19 2013-08-20  3:14:002013-08-20  3:14:00

20_ installing your dryer

installing your dryer

U.S. MODELS:

Risk of Electric Shock:

All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the

neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled

construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is

used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following

instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the

cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8”

(1cm) deep well socket.

9. Connect the Water Inlet Hose. For instructions, go to Connecting the Inlet Hose

on page

10. To ensure that the dryer provides optimal drying performance, it must be level. To

level the dryer, follow the lettered steps below:

a. Using a level, check if the dryer is level side to side and then front to back.

b. If the dryer is not level, adjust the leveling feet on the bottom of the dryer until

the washer is level side to side and back to front. Turning the feet clockwise

retracts the feet. Turning the feet clockwise loosens and extends them.

To set the dryer to the same height as the washer, fully retract the

leveling feet by turning them counterclockwise, then loosen the feet

by turning them clockwise. Once the dryer is the same height as the

washer, follow the directions above to level the dryer.

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than

necessary can cause the dryer to vibrate.

11. Make sure all gas connections (on gas models), exhaust, and electrical connections are complete. Plug in your dryer, and

then check its operation by using the checklist below.

12. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the

line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure the gas supply to your

dryer has been turned on. To confirm gas ignition, check the exhaust for heat.

FINAL INSTALLATION CHECKLIST

 The dryer is plugged into an electrical outlet and grounded properly.

 The exhaust ductwork is hooked up and the joints are taped.

 You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

 The dryer is level and is sitting firmly on the floor.

 For gas models: The gas is turned on and there are no gas leaks.

 Start your dryer to confirm that it runs, heats, and shuts off.

Level

Leveling feet

Retract fully Then loosen

WARNING

DV405ETPAWR_03021F-08_EN_130820.indd Sec5:20DV405ETPAWR_03021F-08_EN_130820.indd Sec5:20 2013-08-20  3:14:002013-08-20  3:14:00

La page charge ...

Samsung DV405ETPAWR Manuel utilisateur

Samsung DV405ETPAWR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents