W10373812A
W10373813A - SP
Designed to use only HE High Efciency
detergents.
Conçue pour l’utilisation d’un détergent haute
efcacité seulement.
BRAVOS
®
TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
Table of Contents
WASHER SAFETY .........................................................2
WHAT’S NEW UNDER THE LID? .................................3
CONTROL PANEL AND FEATURES ............................4
Dispensers .......................................................................6
CYCLE GUIDE ...............................................................7
USING YOUR WASHER ................................................9
Using Laundry Product Dispensers .............................10
Starting Your Washer ....................................................10
WASHER MAINTENANCE .............................................. 12
TROUBLESHOOTING ...................................................... 14
WARRANTY........................................................................ 20
ASSISTANCE OR SERVICE ...........................Back Cover
Table des Matières
SÉCURITÉ DE LA LAVEUSE ......................................21
QUOI DE NEUF SOUS LE COUVERCLE? ................22
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ..........................................23
Distributeurs ..................................................................25
GUIDE DES PROGRAMMES ......................................26
UTILISATION DE LA LAVEUSE ..................................30
Utilisation des distributeurs de produits de lessive ..31
Mise en marche de la laveuse .....................................32
ENTRETIEN DE LA LAVEUSE ........................................ 33
DÉPANNAGE ...................................................................... 35
GARANTIE .......................................................................... 43
ASSISTANCE OU SERVICE ..............Couverture arrière
LAVEUSE HAUTE
EFFICACITÉ À FAIBLE
CONSOMMATION D’EAU
AVEC CHARGEMENT
PAR LE DESSUS BRAVOS
®
GUIDE D’UTILISATION
ET D’ENTRETIEN
Para una version en espanol, visite www.maytag.com
2
WASHER SAFETY
3
When loading the washer, ll it evenly around the basket wall.
INTELLIFILL™
Water Level Control
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. This may take several minutes before water is
added. You will nd a step-by-step description in the “Cycle
Status Lights” section.
You will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
As the washer dampens and moves the load, the level of the
clothes will settle in the basket. This is normal, and does not
indicate that more clothes should be added.
IMPORTANT: You will not see a washer basket full of water
as with your past agitator-style washer.
WHAT’S NEW UNDER THE LID?
Choosing the Right Detergent
Use only High Efciency detergents. The package will be
marked “HE” or “High Efciency.” Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
Normal Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for clothes to soak.
Use only High Efciency (HE) detergent.
Concentrated Cleaning
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
Cleaning with Less Water
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size—no water level selector is needed.
Traditional agitator-style
washer
Washer with low-water
washplate wash system
Washplate
Auto Temperature Control
Auto Temperature Control (ATC) electronically senses and
maintains a uniform wash and rinse water temperature. ATC
regulates incoming hot and cold water. The ATC is automatically
turned on when a cycle is selected.
ATC is available with Hot/Cold, Warm/Warm, and Warm/Cold
settings. The water temperature in the Cold/Cold setting
depends on the water temperature at the water inlet faucets.
ATC ensures consistent cleaning.
Heated water consumes the largest amount of energy that
a washer uses.
4
CONTROL PANEL AND FEATURES
ESTIMATED TIME REMAINING DISPLAY
The Estimated Time Remaining display shows the time
required for the cycle to complete. Factors such as load size
and water pressure may affect the time shown in the display.
Tightly packed, unbalanced loads, or excessive suds may
cause the washer to adjust the cycle time, as well.
POWER/CANCEL BUTTON
Press to turn the washer ON or OFF.
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Cycle Guide” for detailed descriptions of cycles.
START/PAUSE BUTTON
Press to start the selected cycle. Be sure all desired
Modiers and Options have been selected. Press START/
PAUSE once to unlock the lid and add a garment. Press
START/PAUSE to complete the cycle from where it was
stopped. The lid must be closed for the washer to start.
CYCLE MODIFIERS
When you select a cycle, its default modiers will light up.
Not all cycles, options, and modiers are available on all
models.
WASH TEMP/RINSE TEMP
Select a water temperature based on the type of load
you are washing. Use the warmest wash water suitable
for fabrics. Follow garment label instructions.
Warm rinses leave the loads drier and more comfortable
to handle than cold rinses. However, warm rinses also
increase wrinkling. Cold rinses may help with wrinkling
and save energy.
NOTE: In wash water temperatures colder than 60°F
(15.6°C), detergents do not dissolve well. Soils may be
difcult to remove.
SPIN SPEED
This washer automatically selects the spin speed
based on the cycle selected. The preset speeds can
be changed. Not all spin speeds are available with
all cycles.
Faster spin speeds mean shorter dry times, but
may increase wrinkling in your load.
Slower spin speeds mean less wrinkling, but will
leave your load more damp.
1
1
2
3
3
4
SOIL LEVEL
Soil Level (wash time) is preset for each wash cycle. As
you press Soil Level, the cycle time (minutes) will increase
or decrease in the Estimated Time Remaining display and
a different wash time will appear.
For most loads, use the Soil Level that is preset with the
cycle you have chosen. For heavily soiled and sturdy
fabrics, press SOIL LEVEL to select more wash time,
if needed. For lightly soiled and delicate fabrics, press
SOIL LEVEL to select less wash time, if needed. Lower
Soil Level setting will help reduce tangling and wrinkling.
CYCLE OPTIONS
When you select a cycle, its default options will light up. Not
all cycles, options, and modiers are available on all models.
WATER SAVE SPRAY RINSE
Use this option to save water by using a spray rinse
instead of a deep water rinse. This option is the default
setting on some cycles, and selectable on other cycles.
When using fabric softener, always select the Fabric
Softener button, or select Extra Rinse; both of these
options will dispense fabric softener in a deep rinse.
FABRIC SOFTENER
This option must be selected if using fabric softener
during a cycle. It ensures that fabric softener is added
at the correct time in the rinse for even distribution.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
END SIGNAL
Use this option to adjust volume of the signal that sounds
at end of cycle. You may select Hi, Low, or Off (no
indicator lit). A louder signal is helpful in removing items
as soon as cycle is complete.
You may also add or remove options for each cycle. Not all
options can be used with all cycles, and some are preset to
work with certain cycles.
4
5
Not all features and cycles are available on all models.
2
6
5
6
7
8
5
LID LOCK INDICATOR
This light indicates that the lid is locked
and cannot be opened. If you need to open
the lid, press START/PAUSE. The lid will
unlock once the washer movement has
stopped. This may take several minutes
if the load was spinning at high speed.
Press START/PAUSE again to restart
the cycle.
CYCLE STATUS LIGHT INDICATORS
The Cycle Status Lights show the progress of a cycle.
At each stage of the process, you may notice sounds
or pauses that are different from traditional washers.
FILL
When the Start/Pause button is pressed, the washer will
rst perform a self-test on the lid lock mechanism. You
will hear a click, the basket will make a slight turn, and
the lid will unlock briey before locking again.
Once the lid has locked the second time, the washer
will use short, slow spins to estimate the load size.
These sensing spins may take 2 to 3 minutes before
water is added to the load and you may hear the hum of
these spins. If the Fill light is on, the washer is working
properly. You will hear the motor turn the basket in short
pulses to thoroughly wet the load. The washer will then
move the load briey, pause to allow water to soak in to
the load, and resume adding water. This process may
repeat until the correct amount of water has been added
for the load. You may also hear water owing through the
dispenser, adding detergent to the load.
NOTE: Avoid opening the lid during the Fill portion of
the cycle. The sensing process will start over when the
washer is restarted. The Fill light may also come on
during the Wash portion of the cycle. This is normal.
WASH
You will hear the motor and washplate moving the load.
Unlike traditional washers, the load is not covered with
water. Low-water cleaning means concentrated cleaning.
Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils. The
motor sounds may change at different stages in the cycle.
The wash time is determined by the selected Soil Level.
RINSE
You will hear sounds similar to the wash cycle as the washer
rinses and moves the load. You may hear the motor turning
on briey (short hum) to move the basket while lling. Fabric
softener will be added if the Fabric Softener option was
selected. Some cycles use spray rinsing.
SPIN
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle and spin speed.
DONE
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
ADD A GARMENT
You may place additional clothing in the wash when
the Add a Garment indicator light is glowing without sacric-
ing wash performance. Press START/Pause once. The Lid
Lock light will turn off. Open the washer lid, add garments
and close the lid. Press START/Pause to restart.
CLEAN WASHER REMINDER
The Clean Washer Reminder indicator lights after 45 wash
cycles without a clean washer cycle. See the “Cleaning your
washer” section to run the clean washer cycle, or you can
press REMINDER RESET button to manually reset clean
washer cycle counter.
7
8
6
DISPENSERS
High Efciency “HE” detergent dispenser
Add liquid or powdered HE detergent
to this dispenser for your main wash cycle.
A
B
C
Use only High Efciency (HE) detergent.
Liquid fabric softener dispenser
Pour measured liquid fabric softener into the
liquid fabric softener dispenser, if desired. It will
dispense automatically at the optimum time when
the Fabric Softener option is selected.
Use only liquid fabric softener in this dispenser.
A
C
B
Liquid chlorine bleach dispenser
This dispenser holds up to 3/4 cup (180 mL) liquid
chlorine bleach. The bleach will be automatically
diluted and dispensed at the optimum time during
the the wash cycle. This dispenser cannot dilute
powdered bleach.
NOTE: Fill dispenser only with liquid chlorine
bleach.
7
CYCLE GUIDE
Items to wash: Cycle:
Wash/Rinse
Temperature:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
Sturdy fabrics,
colorfast items
Heavy
Duty
Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Cottons,
linens,
and mixed
garment loads
Normal Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Max
Extract
Medium
No Spin
Heavy/Stains
Medium
Light
Use this cycle for heavily soiled
or sturdy cotton items. Cycle
combines high-speed wash action
and high-speed spin. A Water Save
Spray Rinse is a preset cycle setting
for this cycle.
Use this cycle for normally soiled
cottons and mixed fabric loads. This
cycle combines high-speed wash
action and medium-speed spin. A
Water Save Spray Rinse is a preset
cycle setting for this cycle.
When washing waterproof/water-
resistant items such as plastic-lined
mattress pads, shower curtains, tarps,
jackets, or sleeping bags, select the
lowest spin speed setting available for
the cycle and washer model
being used.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Heavily soiled
white fabrics
Whites
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
This cycle introduces liquid chlorine
bleach to the load at the proper
time for improved whitening of your
heavily soiled white fabrics. This cycle
combines high-speed wash action
and high-speed spin speed. For
maximum soil and stain removal,
liquid chlorine bleach can be used
in the liquid bleach dispenser or
color-safe bleach, or laundry boosters.
This cycle can also be used for sturdy
color fabrics, such as towels without
liquid chlorine bleach.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Large items such
as sleeping bags,
small comforters,
jackets
Bulky
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Use this cycle to wash large items
such as comforters, sleeping bags,
and blankets. This cycle starts with
a soak to thoroughly saturate your
large load. This is followed by
medium wash action and medium
spin speeds to maintain load balance.
Extra Rinse
Fabric Softener
Normally soiled
sheets
Sheets Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Use this cycle for sheets, pillowcases,
and light blankets or throws. The
wash action of this cycle is designed
to keep large items from tangling and
balling up.
IMPORTANT: For best performance,
drop items in loose heaps evenly
around the basket wall. Do not load
items directly on the impeller for
this cycle.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Heavily
soiled fabrics
Power
Wash
Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Use this cycle for overly soiled
garments and household items that
need additional cleaning effort. This
cycle combines high-speed wash
action, medium-speed spin, and
a deep rinse to ush excess dirt from
the load.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Settings and options shown in bold are default settings for that cycle.
For best fabric care, choose the cycle that best ts the load being washed.
Not all cycles and options are available on all models.
IMPORTANT: When washing waterproof/water-resistant items such as plastic lined mattress pads, shower curtains, tarps, jackets,
or sleeping bags, select the lowest spin speed setting available for the cycle and washer model being used.
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
8
CYCLE GUIDE
Items to wash:
Wash/Rinse
Temperature:
Spin
Speed:
Soil
Level:
Available
Options:
Cycle Details:
No clothes in
washer
Heavily soiled
fabrics
Clean
Washer
with
AFFRESH
Soak
Warm/Cold
Cold/Cold
Heavy/Stains
Medium
Light
Use the Clean Washer with AFFRESH™
cycle once a month to keep the inside
of your washer fresh and clean. This
cycle uses a higher water level. Use
with AFFRESH
®
washer cleaner tablet
or liquid chlorine bleach to thoroughly
clean the inside of your washer. This
cycle should not be interrupted. See
“Cleaning Your Washer.”
IMPORTANT: Do not place garments
or other items in the washer during the
Clean Washer with AFFRESH™ cycle.
Use this cycle with an empty wash tub.
This cycle is preset for a 31-minute
cycle and soak time can be adjusted
according to your needs by selecting
Soil Level. After the selected soak
period has ended, the washer will drain
but does not spin the load. At the end
of Soak, the washer will drain and wait
for a wash cycle to be selected, to
complete the cleaning process.
NOTE: Automatic bleach dispensing
is not part of the soak cycle.
Swimsuits,
items that
need rinsing
only
Rinse
& Spin
Warm/Warm
Warm/Cold
Cold/Cold
Max
Extract
Medium
Low
No Spin
Use this option to get a deep rinse
followed by a high-speed spin. The time
display will include an estimate of how
long it will take to ll and drain the washer.
When to use RINSE & SPIN:
For loads that need rinsing only.
For completing a cycle after the power
has been off. The washer will return to
pause mode if the power was interrupted
or unplugged while cycle was running.
Cycle:
Machine-wash
silks, hand-wash
fabrics and wool
Hand Wash
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Medium
Low
No Spin
Heavy/Stains
Medium
Light
This cycle combines low-speed wash
and low-speed spin action to clean
items labeled as “Machine Washable”
on the garment care label.
Extra Rinse
Water Save Spray
Rinse
Fabric
Softener
Settings and options shown in bold are default settings for that cycle.
For best fabric care, choose the cycle that best ts the load being washed.
Not all cycles and options are available on all models.
Wet load
of clothes
Drain
& Spin
Max
Extract
Medium
Low
Drain & Spin may help shorten drying
times for some heavy fabrics or
special-care items. Drain & Spin may
also be used for draining the washer after
canceling a cycle or completing a cycle
after a power failure.
Lightly soiled
garments
Rapid Wash Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Use this cycle to wash small, lightly
soiled loads that are needed in a hurry.
This short cycle combines high-speed
wash action and high-speed spin for
the optimal cleaning and shortened
dry times. A Water Save Spray Rinse
is a preset cycle setting for this cycle.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
IMPORTANT: When washing waterproof/water-resistant items such as plastic lined mattress pads, shower curtains, tarps, jackets,
or sleeping bags, select the lowest spin speed setting available for the cycle and washer model being used.
Towels and
terrycloth items
Colors/
Towels
Hot/Cold
Warm/Warm
Warm/Cold
Cold/Cold
Max
Extract
Medium
Low
No Spin
Heavy/Stains
Medium
Light
Use this cycle for lightly soiled,
colored clothing or towels. This cycle
is also a good choice for garments
with a wrinkle-free nish. This cycle
uses medium-speed wash action and
medium-speed spin.
Extra Rinse
Water Save
Spray Rinse
Fabric Softener
9
USING YOUR WASHER
Empty pockets. Loose change, buttons, or any small object
can pass under the impeller and become trapped, causing
unexpected sounds.
• Sort items by recommended cycle, water temperature,
and colorfastness.
Separate heavily soiled items from lightly soiled.
Separate delicate items from sturdy fabrics.
Do not dry garments if stains remain after washing; heat can
set stains into fabric.
Treat stains promptly.
Close zippers, fasten hooks, tie strings and sashes.
Remove non-washable trim and ornaments.
Mend rips and tears to avoid further damage to items
during washing.
Helpful Tips:
When washing water-proof or water-resistant items, load
evenly. See “Cycle Guide” for tips and more information on
using the Bulky cycle.
Use mesh bags to help avoid tangling when washing delicate
or small items.
Turn knits inside out to avoid pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up
lint from towels, rugs, and chenille fabrics.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
1. Sort and prepare your laundry
Load garments in loose heaps evenly
around basket wall. Try mixing different
sized items to reduce tangling.
IMPORTANT: Items need to move
freely for best cleaning and to reduce
wrinkling and tangling.
2. Load laundry into washer
10
Using Laundry Product Dispensers
5. Add fabric softener to dispenser
Pour a measured amount of liquid
fabric softener into dispenser; always
follow manufacturer’s directions for correct amount of
fabric softener based on your load size. Then select
Fabric Softener option.
IMPORTANT: Fabric Softener option must be selected
to ensure proper distribution at correct time in cycle.
Do not overll or dilute. Overlling dispenser will cause
fabric softener to immediately dispense into washer.
If Extra Rinse option is selected, fabric softener will be
dispensed in the last rinse.
NOTE: Do not use liquid fabric softener dispenser balls
in this washer. They will not dispense correctly.
Starting Your Washer
6. Press POWER/CANCEL to turn on
washer
Fabric softener dispenser
Add a measured amount of HE
detergent into detergent dispenser.
IMPORTANT: Use only High Efciency detergents. The package
will be marked “HE” or “High Efciency.” Low-water washing
creates excessive sudsing with a regular non-HE detergent.
Using regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
NOTE: If using an Oxi laundry boost product, add to the
detergent dispenser.
HELPFUL TIP: See “Washer Maintenance” for information on
recommended method of cleaning washer dispensers.
4. Add liquid chlorine bleach
to dispenser
3. Add HE detergent to dispenser
Detergent dispenser
Do not overll, dilute, or use more than 3/4 cup (180 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach.
Liquid chlorine
bleach dispenser
Make sure the dispenser drawer is closed completely, then
press POWER/CANCEL to turn on the washer.
11
7. Select cycle
Wash Temp
Hot
Some cold water is added to save
energy. This will be cooler than
your hot water heater setting.
Warm
Some cold water will be added, so
this may be cooler than what your
previous washer provided.
Cold
Warm water may be added to
assist in soil removal and to help
dissolve detergents.
Suggested Fabrics
Whites and pastels
Durable garments
Heavy soils
8. Select cycle modiers
Once you select a cycle, the default settings for that cycle will
be lit. Press the Modier buttons to change the Soil Level, Spin
Speed, and Wash/Rinse Temperature, if desired. Not all settings
are available with all cycles.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
Dark colors that
bleed or fade
Light soils
Bright colors
Moderate to light soils
Turn cycle knob to choose your wash
cycle. The indicator for Estimated
Time Remaining will light up with a
cycle time. For more information, see
“Control Panel”.
10. Press START/PAUSE to begin
wash cycle
9. Select cycle options
Select any other cycle options you may wish to add, if not
previously set. Some cycles will automatically add certain
options such as Extra Rinse. These may be turned off, if
desired.
NOTE: Not all options are available with all cycles.
Press the START/PAUSE button to start the wash cycle. Filling
is delayed for several minutes while load balance is sensed.
When the cycle has nished, the DONE indicator will light
and the end of cycle signal will sound (if set). Promptly remove
garments when cycle is done to prevent odor, reduce wrinkling,
and rusting of metal hooks, zippers, and snaps.
If lid is left open for more than 10 minutes the water will
pump out.
Delay in water ll
Filling is delayed for 2 to 3 minutes to check for load unbalance.
You will hear the hum of the spin prior to lling. This is normal
operation.
12
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid ooding due
to water pressure surge.
NON-USE AND VACATION CARE
CLEANING YOUR DISPENSERS
You may nd laundry product residue leftover in your
dispensers. To remove residue, wipe with a damp cloth and
towel dry.
WASHER MAINTENANCE
CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes.
To keep washer interior odor-free, follow this
recommended monthly cleaning procedure:
1. Make sure the washer is empty.
2. Using recommended AFFRESH
®
washer cleaner,
add one tablet to washer drum.
OR
If using liquid chlorine bleach, add 1 cup (250 mL) to
liquid chlorine bleach dispenser.
IMPORTANT: Do not add detergent to CLEAN
WASHER with AFFRESH
cycle. Do not use more than
recommended amount of bleach to avoid damaging
product over time.
3. Close washer lid.
4. Press POWER/CANCEL.
5. Select CLEAN WASHER with AFFRESH
cycle.
6. Press START/PAUSE. Water will pour into washer
for a moment and pause, lid will lock, then cycle
will continue.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press START/PAUSE twice and run a
RINSE AND SPIN cycle to ensure cleaner or bleach have
been rinsed from washer.
To clean exterior:
1. Use a soft, damp cloth or sponge to wipe up any spills.
2. Use all-purpose surface cleaner, if needed.
IMPORTANT: To avoid damaging the washer’s nish,
do not use abrasive products.
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
WATER INLET HOSES
13
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE AND SPIN cycle for about 30 seconds
to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage
or moving:
1. Refer to “Installation Instructions” to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through BULKY cycle to clean washer and
remove antifreeze, if used. Use only HE High Efciency
detergent. Use half the manufacturer’s recommended
amount for a medium-size load.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain from drain system.
4. Unplug power cord.
5. Place inlet hoses inside washer basket.
6. Drape power cord and drain hose over the console
and secure with masking tape.
7. Place foam packing ring from original shipping materials
back inside washer. If you do not have packing ring,
place heavy blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in
new location.
14
If you experience
Possible Causes
Solution
Feet may not be in contact with the
oor and locked.
Front and rear feet must be in rm contact with oor, and washer
must be level to operate properly. Jam nuts must be tight
against the bottom of the cabinet.
Check oor for exing or sagging. If ooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level the Washer” in the “Installation Instructions”.
Load could be unbalanced.
Load dry items in loose heaps evenly around basket wall.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Avoid washing single items. Balance a single item such as a
rug or jeans jacket with a few extra items. If the dial is ashing,
redistribute the load, close the lid, and press START/PAUSE.
Use Bulky Items cycle for oversized, non-absorbent items
such as comforters or poly-lled jackets. Other items are
not appropriate for Bulky Items cycle. See “Cycle Guide”.
Item or load not suitable for selected cycle. See “Cycle Guide”
and “Using Your Washer” in this “Use and Care Guide”.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump.
It may be necessary to call for service to remove items.
Washer not level.
Water may splash off basket if washer is not level.
Fill hoses not attached tightly.
Tighten ll-hose connection.
Make sure all four ll hose at washers are properly seated.
Drain hose connection
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Check household plumbing for leaks
or clogged sink or drain.
Water can backup out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe,
water pipes, and faucets.)
Fill hose washers
Noises -For normal operating sounds, go to www.maytag.com/help.
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
Objects caught in washer
drain system.
Clicking or metallic
noises
Gurgling or humming
It is normal to hear the pump making a continuous humming sound
with periodic gurgling or surging as nal amounts of water are
removed during the spin/drain cycles.
Washer may be
draining water.
Water Leaks
Check the following for
proper installation:
Do not place tape over drain opening.
An unbalanced load can cause basket to be out of alignment
and cause water to splash off tub. See “Using Your Washer”
for loading instructions.
Washer not loaded as
recommended.
TROUBLESHOOTING
Vibration, rocking, or
“walking”
Not enough water
in washer
Load not completely covered
in water.
This is normal operation for an HE low-water washer. The load will
not be completely underwater. The washer senses load sizes and
adds correct amount of water for optimal cleaning. See “What’s
New under the Lid.
IMPORTANT: Do not add more water to washer. The added water
lifts the load off the impeller, resulting in less cleaning.
Washer not performing as expected
Washer may not be level.
Vibration or Off-Balance
Vibration during spinning
or washer stopped with
all dial lights ashing
Humming
You may hear the hum of the sensing spins after you have started
the washer. This is normal. Sensing spins will take several minutes
before water is added to the washer.
The washer is sensing the
load size.
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
15
If you experience
Possible Causes
Solution
Normal washer operation.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
Washer may be stopped to reduce suds.
The washer senses the dry load with short spins that may take
2 to 3 minutes before water is added. You may hear the hum
of the spins. This is normal.
Washer won’t run or ll,
washer stops working
(cont.)
Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Check proper electrical supply.
Washer may be tightly packed.
Remove several items, rearrange load evenly in basket and add
detergent. Close lid and press START/PAUSE.
Do not add more than 1 or 2 additional items after cycle
has started.
Not using HE detergent or using too
much HE detergent.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and following
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN. Select your
cycle. Press START/PAUSE. Do not add more detergent.
Small items may have been caught in pump or between basket
and tub, which can slow draining.
Empty pockets and use garment bags
for small items.
Washer not draining/
spinning, loads are still
wet
Washer not performing as expected (cont.)
TROUBLESHOOTING
Do not add more water to the washer.
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Washer won’t run or ll,
washer stops working
Check for proper water supply.
Both hoses must be attached and have water owing to
inlet valve.
Both Hot and Cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water ow.
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
16
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4.5"
(114 mm).
Check drain hose for proper installation. Use drain hose
form and securely attach to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the oor. Remove any clogs from drain hose.
Not using HE detergent or using too
much HE detergent.
Suds from regular detergent or using too much detergent can
slow or stop draining or spinning. Use only HE detergent.
Always measure and follow detergent directions for your
load. To remove extra suds, Select RINSE & SPIN. Do not
add detergent.
Load is tangling
Washer not loaded as recommended.
Load garments in loose heaps evenly around the basket wall.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
If you experience
Possible causes
Solution
Incorrect or wrong
wash or rinse
temperatures
Check for proper water supply.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star
®
qualied washers use cooler wash and rinse water
temperatures than traditional top-load washers. This includes
cooler hot and warm washes.
Load not rinsed
Check for proper water supply.
Washer not performing as expected (cont.)
TROUBLESHOOTING
Energy-saving controlled
wash temperatures.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water owing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer maybe clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too
much HE detergent.
The suds from regular detergent can cause the washer
to operate incorrectly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
Washer may be tightly packed.
The washer is less efcient at rinsing when load is tightly
packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
Fabric softener option not selected.
When using fabric softener, be sure the Fabric Softener option
is selected.
Sand, pet hair, lint, etc.
on load after washing
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Add an Extra Rinse to the selected cycle.
Washer not draining/
spinning, loads are
still wet (cont.)
Washer may be tightly packed or
unbalanced.
Tightly packed loads may not allow the washer to spin correctly,
leaving the load wetter than normal. Evenly arrange the wet load
for balanced spinning. Select DRAIN & SPIN to remove excess
water. See “Using Your Washer” for loading recommendations.
Using cycles with a lower spin speed.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
17
If you experience
Possible Causes
Solution
TROUBLESHOOTING
Not using HE detergent or using too
much HE detergent.
Not using correct cycle for fabric type.
Not using dispensers.
Not washing like colors together.
The suds from regular detergent can prevent washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning.
If using Rapid Wash cycle (on some models), wash only a
few items.
Use Whites and Heavy Duty cycle for tough cleaning.
See the “Cycle Guide” to match your load with the best cycle.
Use dispensers to avoid chlorine bleach and fabric softener
staining.
Load dispensers before starting a cycle.
Avoid overlling.
Do not add products directly onto load.
Wash like colors together and remove promptly after the cycle
is complete to avoid dye transfer.
Washer not performing as expected (cont.)
Monthly maintenance not done as
recommended.
Not using HE detergent or using too
much HE detergent.
Run the Clean Washer cycle with AFFRESH™ monthly.
See “Cleaning Your Washer” in “Washer Maintenance”.
Unload washer as soon as cycle is complete.
Use only HE detergent. Be sure to measure correctly.
Always follow the detergent directions.
See “Cleaning your Washer” section.
Odors
Empty pockets, zip zippers, and snap or hook fasteners before
washing to avoid snags and tears.
Sharp items were in pockets during
wash cycle.
Strings and straps could have tangled.
Items may have been damaged before
washing.
Mend rips and broken threads in seams before washing.
Fabric damage can occur if the load is
tightly packed.
Load garments in loose heaps evenly around the basket wall.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer is started.
Tie all strings and straps before starting wash load.
Fabric Damage
Garment care instructions may not
have been followed.
Always read and follow garment manufacturer’s care label
instructions. See the “Cycle Guide” to match your load with
the best cycle.
Washer not loaded as recommended.
Washer senses load size and adds correct amount of water.
This is normal and necessary for clothes to move.
Do not add additional water to washer. Additional water lifts
the laundry off the impeller, resulting in less cleaning.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Add only 1 or 2 garments after washer has started.
Not cleaning or
removing stains
Wash load not completely
covered in water.
Added more water to washer.
Wash action and/or spin speed too
fast for load.
Select a cycle with a slower wash action and slower spin speed.
Note that items will be wetter than when using a higher speed spin.
Load is tangling (cont.)
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
18
Liquid chlorine bleach may have been
added incorrectly.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
If you experience
Possible Causes
Solution
Clogged dispensers or laundry
products dispensing too soon.
Do not overll dispenser. Overlling causes immediate dispensing.
Always select Fabric Softener option to assure proper dispensing.
Load dispensers before starting a cycle.
It is normal for small amounts of water to be remain in dispenser at
the end of the cycle.
Homes with low water pressure may result in residual powder in the
dispenser. To avoid, select a warmer wash temperature if possible,
depending on your load.
Use only liquid chlorine bleach in the Bleach dispenser.
Incorrect dispenser
operation
TROUBLESHOOTING
Washer not performing as expected (cont.)
Error Code Appears in Display
oL (overloaded)
appears in display
Load too large.
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Liquid chlorine bleach not
used in dispenser.
uL (unbalanced load)
appears in display
Load not balanced. The washer is
running a load-balance correction
routine.
Allow the machine to continue. If the dial is ashing and the
machine has stopped, redistribute the load, close the lid, and
press START/PAUSE.
HC (Hot and Cold
hoses reversed)
appears in display
Hot and cold inlet hoses have been
installed incorrectly.
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Sd (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer’s instructions. If the
dial is ashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
dL (Lid cannot lock)
appears in display
An item in the load may be keeping
the lid from locking.
Check for items directly under the lid.
lid (Lid opened)
appears in display
Washer lid left open.
Close the lid to clear the display. If the lid is left open for more
than 10 minutes, the cycle will reset and water in the washer
will drain.
LF (too long to ll)
appears in display
Washer taking too long to ll.
Drain extends more than
4.5" (114 mm) into standpipe.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See “Installation Instructions”.
Ld (too long to drain
water ) appears in
display
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm) into standpipe.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the oor. Remove any clogs from drain hose. See “Installation
Instructions”.
Fabric Damage (cont.)
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
19
Error Code Appears in Display (cont.)
dU (Lid cannot unlock)
appears in display
Objects on washer lid prevent it from
unlocking.
Remove objects, such as a basket of laundry, from the top of
the washer.
F## code (F-type
error code) appears
in display
System error code.
Press START/PAUSE once to clear the code. Then press
START/PAUSE again to restart washer. If code appears again,
call for service.
Fd (Factory Default)
Washer sets back to factory default.
To return all options and modiers to Factory Default, press
POWER/CANCEL, select Drain & Spin cycle, and then press
Extra Rinse, Fabric Softener, Extra Rinse, Fabric Softener within
5 seconds. When done correctly, the 7-segment displays show
“Fd” for 3 seconds and then unit returns to Standby Mode.
If you experience
Possible Causes
Solution
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
20
MAYTAG
®
LAUNDRY LIMITED WARRANTY
This Maytag Limited Warranty supersedes and replaces the limited warranty printed in the Use and Care Guide for products sold
within the United States of America and Canada.
FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR)
For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions attached
to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) will pay for factory
specied parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.
SECOND THROUGH TENTH YEAR LIMITED WARRANTY (DRIVE MOTOR AND WASH BASKET ONLY - LABOR NOT INCLUDED)
In the second through tenth years from the date of original purchase, when this major appliance is installed, operated, and maintained
according t
o instructions attached to or furnished with the product, Maytag will pay for the replacement of the wash basket drive motor and
stainless steel wash basket (side walls only) to correct non-cosmetic defects in materials or workmanship in these parts that prevent function
of the washer and that existed when this major appliance was purchased. This limited 10-year warranty on the wash basket drive motor and
stainless steel wash basket (side walls only) does not include labor.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service
must be provided by a Maytag designated service company. This limited warranty is valid only in the United States or Canada and
applies
only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of original
consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in
a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair
house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air lters or water lters. Consumable parts are excluded from warranty coverage.
4. Damage resulting from accident, alteration, misuse, abuse, re, ood, acts of God, improper ins
tallation, installation not in accordance
with electrical or plumbing codes, or use of products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the nish of your major appliance, unless such damage results
from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Maytag servicer is not available.
9. The removal and reinstallation of y
our major appliance if it is installed in an inaccessible location or is not installed in accordance with
Maytag’s published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be
easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not
allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This warranty
gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specic legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
If you think you need repair service, rst see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem
after checking “Troubleshooting,” additional help can be found by checking theAssistance or Service” section or by calling Maytag. In the
U.S.A., call
. In Canada, call 01/60.
1 / 1

dans d''autres langues