Simplicity 1696232-01 Manuel utilisateur

Catégorie
Moteur
Taper
Manuel utilisateur
Not for
Reproduction
Single Stage Snowthrower
Soplador de nieve de una etapa
Soufeuse à neige à simple
en
Operator’s Manual
Manuel de l'opérateur
fr
es
Manual del operador
1756267
Revision C
Copyright © 2014
Briggs & Stratton Power Products Group, LLC
Milwaukee, WI USA
All rights reserved.
Not for
Reproduction
2
Operator Safety
Table of Contents
Operator Safety ................................................................... 2
Features and Controls ......................................................... 8
Operation .............................................................................9
Maintenance ...................................................................... 14
Storage .............................................................................. 16
Troubleshooting ................................................................. 17
Emissions Warranty ........................................................... 19
Specications .................................................................... 20
NOTE: Please refer to the Customer Contact Guide and Setup
Instructions for additional information.
Safety Alert Symbol and Signal Words
The safety alert symbol is used to identify safety information
about hazards that can result in personal injury. A signal word
(DANGER, WARNING, or CAUTION) is used with the alert symbol
to indicate the likelihood and potential severity of injury. In
addition, a hazard symbol may be used to represent the type of
hazard.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE indicates an action that could result in damage to
the product.
Hazard Symbols and Meanings
Read the Operator’s Manual
Remove key before performing
maintenance
Carbon monoxide poisoning hazard
Fire hazard
Explosion hazard
Kickback hazard
Hot surface hazard
Wear safety glasses
Thrown objects hazard
Amputation hazard - rotating impeller
Amputation hazard - rotating impeller
Amputation hazard - rotating auger
Entanglement hazard - rotating parts
Electric shock hazard
Keep safe distance away
Keep children away
WARNING
Certain components in this product and its related accessories
contain chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm. Wash hands
after handling.
WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects,
or other reproductive harm.
Not for
Reproduction
3
en
Operator Safety
DANGER
Whenever cleaning, repairing, or inspecting the
snowthrower, make sure the engine is OFF, spark plug wire
is disconnected, and all moving parts have stopped.
Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times.
Never operate the snowthrower without proper guards, and
other safety devices in place and working.
Never leave the snowthrower unattended while engine is
running. Always disengage the auger and traction controls,
stop engine, and remove keys.
Keep all loose clothing away from the front of the
snowthrower and auger. Scarves, mittens, dangling
drawstrings, loose clothes, and pants can quickly become
caught in the rotating device and amputation will occur. Tie
up long hair and remove jewelry.
Run the machine a few minutes after discharging snow to
prevent freeze-up of the collector/impeller.
Disengage power to the collector/impeller when
snowthrower is transported or not in use.
Keep hands, feet, and clothing away from
rotating parts. Rotating parts can contact
or entangle hands, feet, hair, clothing, or
accessories.
Failure to observe these safety instructions
will result in traumatic amputation or severe
laceration.
WARNING
Always wear safety glasses or eye shields during
operation, and while performing an adjustment or repair.
Always be aware of the direction the snow is being
thrown. Nearby pedestrians, pets, or property may be
harmed by objects being thrown.
Be aware of your environment while operating the
snowthrower. Don’t run over items such as gravel,
doormats, newspapers, toys, and rocks hidden under
snow, as they can all be thrown from the chute or jam in
the auger.
Use extreme caution when operating on or crossing
gravel drives, walks, or roads.
Adjust the collector housing height to clear gravel or
crushed rock surface.
Never operate the snowthrower near glass enclosures,
automobiles, window wells, drop-offs, and the like without
proper adjustment of the discharge chute angle.
Familiarize yourself with the area in which you plan to
operate the snowthrower. Mark off boundaries of walkways
and driveways.
Objects can be picked up by auger and thrown
from chute. Never discharge snow toward
bystanders or allow anyone in front of the
snowthrower. Failure to observe these safety
instructions will result in death or serious injury.
WARNING
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snowthrowers.
This snowthrower is capable of amputating hands and feet,
and throwing objects. Read and observe all the safety
instructions in this manual. Failure to do so could result in
death or serious injury.
WARNING
Save these original instructions for future reference.
Be thoroughly familiar with the controls and the proper use
of the snowthrower.
Make sure you are properly trained before operating the
snowthrower.
Know how to stop the unit and disengage the controls
quickly.
Never allow anyone to operate the snowthrower without
proper instruction.
Always follow the instructions in the operator’s manual, if
the snowthrower will be stored for an extende d period.
Maintain or replace safety and instruction labels as
necessary.
Never attempt to make major repairs on the snowthrower
unless you have been properly trained. Improper servicing
of the snowthrower can result in hazardous operation,
equipment damage, and voiding of the product warranty.
Read, understand, and follow all the
instructions on the snowthrower and in the
operator’s manual before operating this unit.
Failure to observe the safet y instructions in this
manual could result in death or serious injury.
Discharge chute contains rotating impeller
to throw snow. Never clear or unclog the
discharge chute with your hands. Fingers can
quickly become caught in the impeller. Always
use a clean-out tool.
Failure to observe these safety instructions
will result in traumatic amputation or severe
laceration.
DANGER
Not for
Reproduction
4
Operator Safety
WARNING
Keep children out of the area during operation. Children are
often attracted to the equipment. Be mindful of all persons
present.
Be alert and turn unit off if children enter the area.
Never allow children to operate the unit.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision. Children
may be present.
Tragic accidents can occur if the operator is
not alert to the presence of children. Children
are often attracted to the unit and the operating
activity. Never assume the children will remain
where you last saw them.
Engines give off carbon monoxide, an
odorless, colorless, poison gas. Breathing
carbon monoxide can cause nausea, fainting,
or death.
WARNING
Start and run engine outdoors.
Do not run the engine in an enclosed area, even if doors or
windows are open.
Keep fuel away from sparks, open flames, pilot lights, heat,
and other ignition sources.
Check fuel lines, cap, and fittings frequently for cracks or
leaks. Replace if necessary.
Use an approved fuel container.
If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
Ensure that spark plug, muffler, fuel cap, and air cleaner (if
equipped) are in place and secured.
Do not crank the engine with the spark plug removed.
If fuel is spilled, do not attempt to start the engine, but move
the snowthrower away from the area of the spill, and avoid
creating any source of ignition, until the fuel vapors have
dissipated.
Do not over-prime the engine. Follow the engine starting
instructions in this manual.
If the engine floods, set choke (if equipped) to OPEN/RUN
position, move throttle (if equipped) to FAST position and
crank until engine starts.
When Operating Equipment
Do not tip the snowthrower at an angle which causes the
fuel to spill.
Do not choke the carburetor to stop the engine.
Never run the engine with the air cleaner assembly (if
equipped) or the air filter (if equipped) removed.
When Changing Oil
If you drain the oil from the top oil fill tube, the fuel tank
must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
Transport with fuel tank EMPTY, or with fuel shut-off valve
OFF.
When Storing Gasoline or Equipment With Fuel in Tank
Store away from furnaces, stoves, water heaters, or other
appliances that have pilot light or other ignition source
because they can ignite fuel vapors.
WARNING
When Adding Fuel
Turn off engine and let cool at least 2 minutes before
removing the fuel cap and adding fuel.
Fill fuel tank outdoors or in a well ventilated area.
Do not overfill the fuel tank. To allow for the expansion of
gasoline, do not fill above the bottom of the fuel tank neck.
Fuel and its vapors are extremely flammable
and explosive. Always handle fuel with
extreme care.
Failure to observe these safety instructions can
cause a fire or explosion which will result in
severe burns or death.
Not for
Reproduction
5
Operator Safety
WARNING
Disengage all clutches and shift into neutral before starting
the engine.
Let the engine adjust to outdoor temperatures before
starting to clear snow.
Use a grounded three-wire plug for all snowthrowers
equipped with electric drive motors or electric starting
motors.
WARNING
If there is natural or LP gas leakage in area, do not start
engine.
Do not use pressurized starting fluids because vapors are
flammable.
WARNING
Never touch a hot engine or muffler. Allow muffler, engine
cylinder, and fins to cool before touching.
Remove debris from muffler area and cylinder area.
Install and maintain in working order a spark arrester before
using equipment on forest-covered, grass-covered, or
brush-covered unimproved land.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws. Contact the original equipment manufacturer,
retailer, or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
Running the engine produces heat. Engine
parts, especially muffler, become extremely
hot.
Failure to observe these safety instructions
could result in severe thermal burns on contact.
Safe operation of the snowthrower requires
the proper care and maintenance of the
engine.
WARNING
When performing any maintenance or repairs on the
snowthrower, shut OFF the engine, disconnect spark plug
wire, and keep the wire away from the plug to prevent
someone from accidently starting the engine.
Check shear bolts and other hardware at frequent intervals
for proper tightness.
Keep nuts and bolts tight and keep snowthrower in good
condition.
Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they are
not functioning properly.
Components are subject to wear, damage, and deterioration.
Frequently check components and replace with
recommended parts, when necessary.
Check control operation frequently. Adjust and service as
required.
Use only factory authorized replacement parts, or like, parts
when making repairs.
Always comply with factory specifications on all settings and
adjustments.
Use only factory authorized, or like, attachments and
accessories such as wheel weights, counterweights, or cabs.
Never attempt to make any adjustments while the engine
is running (except when specifically recommended by the
factory).
This snowthrower must be properly
maintained to ensure safe operation and
performance. Failure to observe the safety
instructions in this manual could result in
death or serious injury.
en
Not for
Reproduction
6
WARNING
This snowthrower is only as safe as the opera-
tor. If it is misused, or not properly maintained,
it can be dangerous. Remember you are re-
sponsible for your safety and those around you.
Keep the area of operation clear of all persons, particularly
small children and pets.
Thoroughly inspect the area where the snowthrower will be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
Do not operate the snowthrower without wearing adequate
winter clothing.
Wear footwear that will improve footing on slippery surfaces.
Use caution to avoid slipping or falling especially when
operating the snowthrower in reverse.
Never operate the snowthrower without good visibility or
light. Always be sure of your footing, and keep a firm hold on
the handles.
Do not clear snow across the face of slopes. Use extreme
caution when changing direction on slopes. Do not attempt
to clear steep slopes.
Do not overload the machine capacity by attempting to clear
snow too quickly.
Never operate the snowthrower at high transport speeds on
slippery surfaces. Look behind the snowthrower and use
care when operating in reverse.
Do not use the snowthrower on surfaces above ground level
such as roofs of residences, garages, porches, or other such
structures or buildings.
Operators should evaluate their ability to operate the
snowthrower safely enough to protect themselves and
others from injury.
The snowthrower is intended to remove snow only. Do not
use the snowthrower for any other purpose.
Do not carry passengers.
After striking a foreign object, shut OFF the engine,
disconnect the cord on electric motors, thoroughly inspect
the snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
If the snowthrower vibrates abnormally, shut OFF the
engine. Vibration is generally a warning of trouble. See an
authorized dealer if necessary for repairs.
For models equipped with electric starting motors,
disconnect the power cord after the engine starts.
Operator Safety
WARNING
Rapid retraction of the starter cord (kickback)
will pull your hand and arm toward the engine
faster than you can let go.
Broken bones, fractures, bruises, or sprains
could result.
When Starting the Engine
Pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
WARNING
Damaged or ungrounded power cords could
cause electric shock.
Electric shock could cause severe burns or
death.
When Using the Electric Starter
The power cord must be properly grounded at all times.
Use only a three-conductor power cord properly grounded
to the power source.
If the extension cord is damaged, it must be replaced a
qualied person to avoid a hazard.
Not for
Reproduction
7
en
Operator Safety
Safety Decals
Before operating the snowthrower, read and understand the
installed safety decals. The cautions and warnings are provided
to help you avoid personal injury or damage to your snowthrower.
If any safety decals become damaged or illegible, order
replacements from your local authorized service dealer.
A Part No. 1737865 Chute Danger Decal
B Part No. 1739966 Auger Danger Decal
C Part No. 279655 Engine Warning Decal
Thrown Ob-
jects Hazard
• Never direct
discharge chute
towards persons or
property.
Danger objets
projetés
• Ne jamais diriger la
chute en direction
des personnes ou
biens matériels.
Read the operator’s
manual for operat-
ing and safety
instructions.
Lire les consignes de
sécurité et
d’utilisation dans le
manuel d’utilisation.
Shut o engine and
remove key before
performing
maintenance or
repair work.
Arrêter le moteur et
retirer la clé avant
d’eectuer tout
entretien ou toute
réparation.
Amputation
Hazard
Contact with auger
will cause serious
injury.
• Keep hands, feet
and clothing away.
• Keep bystanders
away.
Risque
d’amputation
• Tout contact avec la
tariére provoquera
de graves blessures.
• Tenir vos pieds, vos
mains et vêtements
á distance.
• Tenir les specta-
teurs á distance.
A
B
C
Not for
Reproduction
8
Features and Controls
Snowthrower and Engine Controls
A Auger Control / Auger
B
Chute Control - Handle Mount (if equipped)
Chute Control - Chute Mount (if equipped)
C
Deector Control - Trigger or Wing Knob
D
— Starter Button
E
Starter Receptacle
F
Starting Instructions Decal (if equipped)
G
Starting Instructions Decal (if equipped)
H
Headlight (if equipped)
I
Choke Control
J Fuel Tank and Cap
K Oil Fill/Dipstick
L
Primer Button
M ON/OFF or Push/Pull Key
N Starter Cord Handle
O Oil Drain Plug
E
D
L
J
I
K
M
O
C
1739977
H
G
F
B
A
N
B
C
A
Control Symbols and Meanings
On / O switch
Choke closed; choke open
Push primer 2 times
Plug in extension cord
Press button to start
Engage auger control
Rotate chute control
Not for
Reproduction
9
Operation
Oil Recommendations
NOTICE: The engine was shipped from the factory without oil.
Before you start the engine, ensure that you add oil according to
the instructions in this manual. If you start the engine without oil, it
will be damaged beyond repair and will not be covered under the
warranty.
Use a high quality detergent oil classified for Service SG, SH,
SJ, SL, or higher. Synthetic 5W30 motor oil is acceptable for all
temperatures. DO NOT mix oil with gasoline. See chart below for
oil recommendations.
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-
sumption. Check oil level more frequently.
Add Oil / Check Oil Level
1. Ensure the snowthrower is level.
2. Clean the oil dipstick area of any debris.
3. See Specifications for the oil capacity.
4. Remove the oil dipstick (A, Figure 1) and wipe it with a clean
cloth.
5. Add oil slowly into the engine oil fill (B).
6. Wait one minute and then insert the oil dipstick and turn it
clockwise to tighten.
7. Remove the oil dipstick and check the oil level.
8. If necessary, add oil until the level reaches the full mark (C) on
the oil dipstick. Do not overfill.
9. Insert and tighten the oil dipstick securely.
B
A
C
D
Figure 1
en
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane / 87 AKI (91 RON). For high altitude
use, see below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE: Do not use unapproved gasolines, such as E15 and
E85. Do not mix oil in gasoline or modify the engine to run on
alternate fuels. Use of unapproved fuels will cause damage to
engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel. See Storage. All fuel is not the same. If
starting or performance problems occur, change fuel providers
or change brands. This engine is certified to operate on gasoline.
The emissions control system for this engine is EM (Engine
Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane
/ 85 AKI (89 RON) gasoline is acceptable. For carbureted
engines, high altitude adjustment is required to remain emissions
compliant. Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions. Contact a Briggs & Stratton Authorized Service Dealer
for high altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet (762
meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude
adjustment is necessary.
Not for
Reproduction
10
Operation
Start the Engine
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap
(D, Figure 1).
2. Fill the fuel tank with fuel. To allow for expansion of the fuel, do
not fill above the bottom of the fuel tank neck.
3. Install the fuel cap.
Add Fuel
WARNING
When Adding Fuel
Turn off engine and let cool at least 2 minutes before
removing the fuel cap and adding fuel.
Fill fuel tank outdoors or in a well ventilated area.
Do not overfill the fuel tank. To allow for the expansion of
gasoline, do not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat,
and other ignition sources.
If fuel spills, wait until it evaporates before starting engine.
Fuel and its vapors are extremely flammable
and explosive. Always handle fuel with
extreme care.
Failure to observe these safety instructions can
cause a fire or explosion which will result in
severe burns or death.
WARNING
When Starting Engine
Ensure that spark plug, muffler, fuel cap, and air cleaner (if
equipped) are in place and secured.
Do not crank the engine with the spark plug removed.
If fuel is spilled, do not attempt to start the engine, but move
the snowthrower away from the area of the spill, and avoid
creating any source of ignition, until the fuel vapors have
dissipated.
Do not over-prime the engine. Follow the engine starting
instructions in this manual.
If the engine floods, set choke (if equipped) to OPEN/RUN
position, move throttle (if equipped) to FAST position and
crank until engine starts.
Fuel and its vapors are extremely flammable
and explosive. Always handle fuel with
extreme care.
Failure to observe these safety instructions can
cause a fire or explosion which will result in
severe burns or death.
WARNING
Rapid retraction of the starter cord (kickback)
will pull your hand and arm toward the engine
faster than you can let go.
Broken bones, fractures, bruises, or sprains
could result.
When Starting the Engine
Pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
WARNING
Damaged or ungrounded power cords could
cause electric shock.
Electric shock could cause severe burns or
death.
When Using the Electric Starter
The power cord must be properly grounded at all times.
Use only a three-conductor power cord properly grounded
to the power source.
If the extension cord is damaged, it must be replaced a
qualied person to avoid a hazard.
NOTE: The electric starter is designed for a three-conductor
power cord only and operates on standard household current. If a
properly grounded electrical source is not available, DO NOT use
the electric starter. Contact a licensed electrician for installation of
a properly grounded system.
1. Check the oil level. See Add Oil / Check Oil Level.
2. Ensure the auger control is disengaged.
3. Insert the ON/OFF key (A, Figure 2) and turn to the ON
position or insert the Push/Pull key, if equipped.
Engines give off carbon monoxide, an
odorless, colorless, poison gas. Breathing
carbon monoxide can cause nausea, fainting,
or death.
WARNING
Start and run engine outdoors.
Do not run the engine in an enclosed area, even if doors or
windows are open.
Not for
Reproduction
11
Operation
4. Turn the choke control (B) to the closed position.
NOTE: Do not close the choke control to start a warm engine.
5. Press the primer button (C) two times.
NOTE: Do not press the primer button to start a warm engine.
6. Rewind start: Firmly hold the starter cord (D). Pull the starter
cord slowly until resistance is felt, then pull rapidly.
7. Electric start: First connect the power cord (not supplied)
(E, Figure 3) to the starter receptacle (F) and then into a wall
receptacle. If an additional power cord is required, ensure it is
a three-conductor cord.
8. Electric start: Press the starter button (G). After the engine
starts, disconnect the power cord from the wall receptacle first
and then from the starter receptacle.
NOTICE: To extend the life of the starter, use short starting
cycles (five seconds maximum). Wait one minute between
starting cycles.
9. As the engine warms up, move the choke control (B, Figure 2)
to the open position.
NOTE: If the engine does not start after three attempts, see
Troubleshooting.
Figure 2
B
C
A
D
E
G
F
Figure 3
WARNING
Do not choke the carburetor to stop the engine.
Gasoline and vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
1. Turn the ON/OFF key (A, Figure 2) to the OFF position or
remove the Push/Pull key, if equipped.
2. Keep the key in a safe place out of the reach of children. The
engine cannot be started without the key.
Stop the Engine
en
Not for
Reproduction
12
Operation
A
B
C
Figure 4
Operate the Snowthrower
WARNING
Keep children out of the area during operation. Children are
often attracted to the equipment. Be mindful of all persons
present.
Be alert and turn unit off if children enter the area.
Tragic accidents can occur if the operator is
not alert to the presence of children. Children
are often attracted to the unit and the operating
activity. Never assume the children will remain
where you last saw them.
WARNING
Always be aware of the direction the snow if being thrown.
Adjust the collector housing height to clear gravel or
crushed rock surface.
Ice, gravel, or other unintended objects can be
picked up by the auger and thrown from the
chute with force.
Objects thrown from the chute could cause
death, serious injury, or property damage.
DANGER
Read and observe all the safety instructions in this
manual. Failure to do so will result in death or serious
injury.
Never clear or unclog the discharge chute with your hands.
Fingers can quickly become caught and traumatic amputa-
tion or severe laceration will result.
Always use a clean-out tool to clear or unclog the dis-
charge chute.
This snowthrower is capable of amputating
hands and feet, and throwing objects. Hand
contact with the rotating auger inside the
discharge chute is the most common cause of
injury associated with snowthrowers.
1. Start the engine and allow it to warm up several minutes. See
Start the Engine.
2. Adjust the direction of the chute and the angle of the deflector
to the desired positions. See Discharge Chute and
Deflector.
3. Pull the auger control (C, Figure 4, Figure 5) against the
handle to engage the auger.
4. When clearing snow is completed, release the auger control.
5. Allow the engine to run for one minute, then stop the engine.
See Stop the Engine.
Not for
Reproduction
13
en
Discharge Chute and Deector
Chute Rotation - Handle Mount (if equipped)
1. Squeeze and hold the button on the chute control handle (A,
Figure 4).
2. Push the handle forward or pull it rearward to rotate the chute.
3. Release the button to lock the chute in the desired position.
NOTICE: Do not use excessive force when trying to operate
the control.
Chute Rotation - Chute Mount (if equipped)
1. Grasp the chute control handle at the base of the chute (A,
Figure 5).
2. Turn the handle left or right to rotate the chute. A tension plate
holds the chute in the desired position.
NOTICE: Do not use the chute control handle to lift the
snowthrower.
Deflector Adjustment
1. Squeeze and hold the button on the deflector control handle
(B, Figure 4), or loosen the wing knob (B, Figure 5).
2. Move the control handle up or down to adjust the snow
discharge height and distance.
3. Release the button to lock the deflector in the desired
position, or tighten the wing knob.
Operation
A
B
C
Figure 5
DANGER
Read and observe all the safety instructions in this
manual. Failure to do so will result in death or serious
injury.
Never clear or unclog the discharge chute with your hands.
Fingers can quickly become caught and traumatic amputa-
tion or severe laceration will result.
Always use a clean-out tool to clear or unclog the dis-
charge chute.
This snowthrower is capable of amputating
hands and feet, and throwing objects. Hand
contact with the rotating auger inside the
discharge chute is the most common cause of
injury associated with snowthrowers.
Snowthrower Safety Test
1. Start the snowthrower and engage the auger control (C,
Figure 4, Figure 5) for several seconds.
2. Release the auger control.
3. The auger must stop within 5 seconds after the auger control
is released. If it does not:
a. Adjust the control cable.
b. If the auger still does not stop within 5 seconds, see an
Authorized Dealer.
Clearing a Clogged Discharge Chute
1. STOP THE ENGINE!
2. Ensure that the impeller blades have stopped rotating.
3. Use a clean-out tool to remove snow from the discharge
chute. Never clear a clogged discharge chute with your
hands!
DANGER
Discharge chute contains rotating impeller
to throw snow. Never clear or unclog the
discharge chute with your hands. Fingers can
quickly become caught in the impeller. Always
use a clean-out tool.
Failure to observe these safety instructions
will result in traumatic amputation or severe
laceration.
Not for
Reproduction
14
Maintenance Schedule
Maintenance
A
B
Figure 6
Figure 7
Add Oil
1. Ensure the snowthrower is level.
2. Clean the oil dipstick area of any debris.
3. See Specifications for the oil capacity.
4. Remove the oil dipstick (A, Figure 1) and wipe it with a clean
cloth.
5. Add oil slowly into the engine oil fill (B).
6. Wait one minute and then insert the oil dipstick and turn it
clockwise to tighten.
7. Remove the oil dipstick and check the oil level.
8. If necessary, add oil until the level reaches the full mark (C) on
the oil dipstick. Do not overfill.
9. Insert and tighten the oil dipstick securely.
2. Remove the oil drain plug (B, Figure 7) and tilt the
snowthrower slightly to drain the oil into an appropriate
container.
3. After the oil has drained, install and tighten the oil drain plug.
Emissions Control Service
Maintenance, replacement, or repair of the emissions control
devices and systems may be performed by any non-road engine
repair establishment or individual. However, to obtain “no charge”
emissions control service, the work must be performed by a
factory authorized dealer.
Change Oil
Used oil is a hazardous waste product and must be disposed of
properly. Do not discard with household waste. Check with your
local authorities, service center, or dealer for safe disposal or
recycling facilities.
Remove Oil
1. With engine off but still warm, remove the key and then
disconnect the sparkplug wire (A, Figure 6) and secure it
away from the sparkplug.
NOTE: To access the sparkplug wire, you must remove the
snow hood from the engine. See Access the Sparkplug.
First 5 Hours
Change oil
Before Each Use
Check engine oil level
Perform the snowthrower safety test
Check scraper bar and rubber auger for wear
After Each Use
Remove accumulated snow and slush to prevent freezing of the
controls, wheels, discharge chute, and auger
Every 25 Hours or Annually
Check snowthrower for loose hardware
Check auger control cable adjustment
Every 50 Hours or Annually
Change engine oil
Check condition of muer and muer guard
Annually
Replace sparkplug
Check valve clearance *
* Not required unless problems are noted with engine
performance. See an authorized service dealer for this item.
Not for
Reproduction
15
Maintenance
4. Lower the cable cover into place.
5. Repeat the inspection procedure above. If the auger does not
rotate or does not stop as described, contact an authorized
service dealer to have the snowthrower inspected.
Access the Sparkplug
To access the sparkplug, the snow hood must be removed as
follows:
1. Turn the ON/OFF key (A, Figure 9) to the OFF position or
remove the Push/Pull key, if equipped.
2. Grasp the choke control knob (B) and pull up to remove it.
3. Remove the mounting screws or knobs (C) on the snow
hood.
4. Lift the snow hood (D) off the base and tilt it forward. Do not
disconnect the primer hose (E) or the keyswitch wire (F).
5. Disconnect the sparkplug wire, then remove the sparkplug (G)
to clean or replace it. See Specifications.
6. After installing the sparkplug, connect the sparkplug wire.
7. Ensure that the primer hose and keyswitch wire are properly
connected, then fit the snow hood into the base and secure
with the mounting screws or knobs.
8. Align the slots in the choke control knob with the tabs on
the choke shaft and push down to install. If the knob is not
properly installed, the choke control will not operate.
A
B
C
Control Cable Adjustment
WARNING
The auger must stop within 5 seconds after the auger control is
released. If it does not, adjust the control cable. See Adjust-
ment below or contact an authorized service dealer to adjust
the control cable.
Inspection
The auger should rotate only when the auger control is engaged
and must stop within 5 seconds when the auger control is
released. If the auger does not rotate or does not stop as
described, adjust the control cable or contact an authorized
service dealer to adjust the control cable.
If the drive belt has broken, contact an authorized service dealer
to replace the belt and adjust the control cable.
Adjustment
1. Stop the engine and remove the key. See Stop the Engine.
2. Lift the cable cover (A, Figure 8) to expose the adjustment
loops (B) and the cable end fitting (C).
3. Remove the end fitting from the adjustment loop and reinstall
as follows:
If the auger rotates while the auger control is not
engaged, lengthen the control cable by installing
the end fitting in the next lowest loop (decrease belt
tension).
If the auger does not rotate when the auger control is
engaged, shorten the control cable by installing the end
fitting in the next highest loop (increase belt tension).
NOTE: Some slack must remain in the cable when the auger
control is not engaged.
Figure 8
A
C
E
B
D
F
G
Figure 9
en
Not for
Reproduction
16
Maintenance
Figure 10
Auger and Scraper Bar Maintenance
Before each use, check wear limit on rubber auger and gap
between scraper bar support and ground (A, Figure 10).
• If wear limit on the rubber auger is reached, the two
rubber flights need replacing. See authorized dealer.
• If scraper bar support makes contact with the ground,
the scraper bar needs replacing. See authorized dealer.
Not for
Reproduction
17
Storage
en
WARNING
Fuel and its vapors are extremely ammable and
explossive. Always handle fuel with extreme care.
Failure to observe these safety instructions can cause
a re or explosion which will result in severe burns or
death.
When Storing Gasoline or Equipment With Fuel in
Tank
Store away from furnaces, stoves, water heaters, or
other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
Storage
Engine Oil
While the engine is still warm, change the engine oil. See
Maintenance.
Before Placing in Storage
1. Thoroughly clean the snowthrower.
2. Remove the sparkplug. Clean and re-gap, if necessary,
or replace the sparkplug.
3. Make sure all nuts, bolts, and screws are securely
fastened.
4. Inspect moving parts for wear or damage. Replace
parts as necessary.
5. Lubricate the controls and moving parts.
6. Spray unpainted metal surfaces with a rust preventative.
7. Fold down the upper handle, if desired.
8. For indoor storage, cover the snowthrower and store it
in a dry area away from furnaces, stoves, water heaters,
or other appliances that have pilot lights or other ignition
sources.
9. For outdoor storage, raise the snowthrower off the
ground and cover it with a heavy tarpaulin.
After Removing from Storage
1. Raise the upper handle and tighten the handle knobs
securely.
2. Remove the oil dipstick and check the oil level. If
necessary, add oil until the level reaches the FULL mark
on the oil dipstick. Do not overfill.
3. Fill the fuel tank with fresh fuel.
4. Ensure that all guards, shields, and covers are in place
and that all fasteners are tight.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system
or on essential carburetor parts. To keep fuel fresh, use
Briggs & Stratton® Advanced Formula Fuel Treatment
& Stabilizer, available wherever Briggs & Stratton genuine
service parts are sold.
There is no need to drain gasoline from the engine if a fuel
stabilizer is added according to instructions. Run the engine
for 2 minutes to circulate the stabilizer throughout the fuel
system before storage. If gasoline in the engine has not
been treated with a fuel stabilizer, it must be drained into an
approved container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage container is
recommended to maintain freshness.
Not for
Reproduction
18
Troubleshooting
Problem Cause Solution
Auger does not stop when
auger control is released
Control cable requires
adjustment
Adjust the control cable. If the cable adjustment does not solve the
problem, see an authorized dealer.
Auger does not turn when
auger control is engaged
Control cable requires
adjustment
Adjust the control cable. If the cable adjustment does not solve the
problem, see an authorized dealer.
Chute rotation or deector
adjustment does not work
Fasteners are too tight;
handle mount control
damaged
Contact an authorized service dealer.
Chute or deflector is frozen Clear snow or ice from chute and deflector parts; place snowthrower in a
heated area until snow or ice melts.
Engine does not start Key is off or not inserted Turn key to the ON position or insert Push/Pull key.
Primer not pressed Press primer button twice before pulling starter rope.
Out of fuel Fill fuel tank with fresh fuel.
Choke open - cold engine Turn choke to closed position before pulling starter rope.
Engine flooded Turn choke to open position; pull starter rope several times until engine
starts.
No spark Connect sparkplug wire; replace sparkplug.
Water in fuel or old fuel Drain fuel tank; fill fuel tank with fresh fuel.
Cord not plugged in or circuit
breaker tripped (electric start
models)
Plug in cord or replace defective cord; reset circuit breaker.
Engine is hard to start or
runs poorly
Incorrect oil Change oil to lighter viscosity (such as 5W-30).
Sparkplug fouled, worn, or
gapped incorrectly
Clean and re-gap sparkplug; replace sparkplug. Contact an authorized
service dealer.
Choke control set incorrectly Open choke control gradually as engine warms up.
Excessive vibration Loose parts or damaged
parts
Stop snowthrower immediately. Contact an authorized service dealer.
Scraper bar does not
clean hard surface
Scraper bar worn Scraper bar needs replacing. Contact an authorized service dealer.
Snowthrower does not
discharge snow
Control cable requires
adjustment
Adjust the control cable. See Maintenance section or contact an
authorized service dealer to adjust the cable.
Drive belt worn or broken See authorized dealer to replace the belt.
Discharge chute clogged
with snow
STOP THE ENGINE! Ensure that the auger has stopped rotating. Use
a clean-out tool to remove snow from the discharge chute. Never clear
a clogged discharge chute with your hands! Refer to “Warnings” in
Operator Safety section.
Snowthrower does not
self-propel
Rubber auger is worn or
damaged
Rubber auger needs replacing. Contact an authorized service dealer.
Not for
Reproduction
19
Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control Warranty Statement
Your Warranty Rights And Obligations
For Briggs & Stratton Engine Models with “F” Trim Designation
(Model-Type-Trim Representation xxxxxx xxxx Fx)
January 2014
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased
to explain the emissions control system warranty on your Model Year 2014-2015 engine/
equipment. In California, new small off-road engines and large spark ignited engines less
than or equal to 1.0 liter must be designed, built, and equipped to meet the State’s stringent
anti-smog standards. B&S must warrant the emissions control system on your engine/
equipment for the periods of time listed below provided there has been no abuse, neglect, or
improper maintenance of your engine/equipment.
Your exhaust emissions control system may include parts such as the carburetor or fuel
injection system, ignition system, and catalytic converter. Also included may be hoses, belts,
connectors, sensors, and other emissions-related assemblies. Your evaporative emission
control system may include parts such as: carburetors, fuel tanks, fuel lines, fuel caps, valves,
canisters, filters, vapor hoses, clamps, connectors, and other associated components. Where
a warrantable condition exists, B&S will repair your engine/equipment at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
Small off-road engines and large spark ignited engines less than or equal to 1.0 liter, and
any related emissions components of the equipment, are warranted for two years*. If any
emissions-related part on your B&S engine/equipment is defective, the part will be repaired
or replaced by B&S.
* Two years or for the time period listed in the respective engine or product warranty
statement, whichever is greater.
Owner’s Warranty Responsibilities:
As the engine/equipment owner, you are responsible for the performance of the required
maintenance listed in your Operator’s Manual. B&S recommends that you retain all
receipts covering maintenance on your engine/equipment, but B&S cannot deny warranty
solely for the lack of receipts or your failure to ensure the performance of all scheduled
maintenance.
As the engine/equipment owner, you should however be aware that B&S may deny you
warranty coverage if your engine/equipment or a part has failed due to abuse, neglect,
improper maintenance, or unapproved modifications.
You are responsible for presenting your engine/equipment to a B&S distribution center,
servicing dealer, or other equivalent entity, as applicable, as soon as a problem exists.
The warranty repairs should be completed in a reasonable amount of time, not to exceed
30 days. If you have any questions regarding your warranty rights and responsibilities, you
should contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty Coverage.
It is in addition to the B&S engine warranty for non-regulated engines found in the Operator’s
Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions control
systems parts) to the extent these parts were present on the B&S engine and/or B&S
supplied fuel system.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor and internal parts
Fuel pump
Fuel line, fuel line fittings, clamps
Fuel tank, cap and tether
Carbon canister
b. Air Induction System
Air cleaner
Intake manifold
Purge and vent line
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
2. Length of Coverage
For a period of two years from date of original purchase*, B&S warrants to the original
purchaser and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources Board;
that it is free from defects in material and workmanship that could cause the failure of a
warranted part; and that it is identical in all material respects to the engine described in
the manufacturer’s application for certification. The warranty period begins on the date the
engine is originally purchased.
* Two years or for the time period listed in the respective engine or product warranty
statement, whichever is greater.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required maintenance in
the Oper
ator’s Manual supplied, is warranted for the warranty period stated above. If
any such part fails during the period of warranty coverage, the part will be repaired or
replaced by B&S at no charge to the owner. Any such part repaired or replaced under the
warranty will be warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the Operator’s Manual
supplied, is warranted for the warranty period stated above. Any such part repaired or
replaced under warranty will be warranted for the remaining warranty period.
Any warranted part that is scheduled for replacement as required maintenance in the
Operator’s Manual supplied, is warranted for the period of time prior to the first scheduled
replacement point for that part. If the part fails prior to the first scheduled replacement,
the part will be repaired or replaced by B&S at no charge to the owner. Any such part
repaired or replaced under warranty will be warranted for the remainder of the period prior
to the first scheduled replacement point for the part.
Add-on or modified parts that are not exempted by the Air Resources Board may not
be used. The use of any non-exempted add-on or modified parts by the owner will be
grounds for disallowing a warranty claim. The manufacturer will not be liable to warrant
failures of warranted parts caused by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the failure of any
warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine warranty
policy. Warranty coverage does not apply to failures of emissions parts that are not original
equipment B&S parts or to parts that fail due to abuse, neglect, or impr
oper maintenance as
set forth in the B&S engine warranty policy. B&S is not liable for warranty coverage of failures
of emissions parts caused by the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information
On Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-road
Emissions Standard must display information regarding the Emissions Durability Period
and the Air Index. Briggs & Stratton makes this information available to the consumer on our
emissions labels. The engine emissions label will indicate certification information.
The Emissions Durability Period describes the number of hours of actual running time for
which the engine is certified to be emissions compliant, assuming proper maintenance in
accordance with the Operator’s Manual. The following categories are used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 50
hours of actual engine running time. Engines greater than 80 cc displacement are certified to
be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 125
hours of actual engine running time. Engines greater than 80 cc displacement are certified to
be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 300
hours of actual engine running time. Engines greater than 80 cc displacement are certified to
be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore,
the Emissions Durability Period of an engine with an intermediate rating would equate to
10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental Protection
Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of operating
hours for which the engine has been shown to meet Federal emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
en
Not for
Reproduction
20
Specifications
Engine Brand Briggs & Stratton
Engine Model Series Snow Series
Engine Type 4-Cycle
Starting System Recoil Start and Electric Start
Oil Capacity 20 oz (0,59 L)
Fuel Tank Capacity 3.0 qts (2,8 liters)
Sparkplug Gap .030 in (0,76 mm)
Sparkplug Torque 180 lb-in (20 Nm)
The spark ignition system on this snowthrower complies with Canadian standard ICES-002.
Power Ratings
The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers)
code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are derived
at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived at 3600
RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air
cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than
net engine power and is aected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide
array of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given piece of
power equipment. This dierence is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner,
exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of
higher rated power for this engine.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Simplicity 1696232-01 Manuel utilisateur

Catégorie
Moteur
Taper
Manuel utilisateur