Whirlpool UVL6036JSS Mode d'emploi

Marque: Whirlpool

Modèle: UVL6036JSS

Catégorie: Hottes

Taper: Mode d'emploi

36" (91.4 CM) AND 48" (121.9 CM) HOOD LINER

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

CAISSE DE HOTTE

36" (91,4 CM) ET 48" (121,9 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web à

www.whirlpool.ca

Table of Contents/Table des matières............................................................................. 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3ZIC/W11374537A

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS ................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS..................................................7

Prepare Location..........................................................................7

Install Hood Liner Internal Blower Motor .....................................8

Install Hood Liner In-Line

(External Type) Blower Motor.....................................................10

Make Electrical Connections for In-Line

Blower Motor System ................................................................11

Make Electrical

Power Supply

Connection to Hood Liner..........................................................12

Complete Installation and Check Operation..............................13

RANGE HOOD USE......................................................................14

Range Hood Controls ................................................................14

RANGE HOOD CARE...................................................................15

Cleaning......................................................................................15

WIRING DIAGRAM .......................................................................16

ASSISTANCE OR SERVICE.........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories................................................................................17

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................19

EXIGENCES D'INSTALLATION ...................................................21

Outils et pièces...........................................................................21

Exigences d'emplacement.........................................................21

Exigences concernant l’évacuation ...........................................22

Spécifications électriques ..........................................................23

INSTRUCTIONS D’INSTALLATION.............................................24

Préparation de l'emplacement...................................................24

Installation du moteur du ventilateur interne

de la caisse de la hotte ..............................................................25

Installation du moteur du ventilateur

en ligne (externe) de la caisse de la hotte...............................

...27

Réalisation des connexions électriques

du système du moteur du ventilateur en ligne...........................28

Réalisation des connexions de l’alimentation

électrique à la caisse de la hotte................................................30

Achever l'installation et vérifier le fonctionnement ....................30

UTILISATION DE LA HOTTE .......................................................31

Commandes de la hotte de cuisinière .......................................31

ENTRETIEN DE LA HOTTE..........................................................32

Nettoyage ...................................................................................32

SCHÉMA DE CÂBLAGE...............................................................33

ASSISTANCE OU SERVICE......................................................

...34

Au Canada..................................................................................34

Accessoires ................................................................................34

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Level

Drill

1¼" (3 cm) drill bit

¹⁄8 " (3 mm) drill bit

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Parts needed

Home power supply cable

1 - ½" (1.3 cm) UL listed or CSA approved strain relief

3 UL listed wire connectors

1 wall or roof cap

Metal vent system

Blower motor system - internal or external (see “Blower

Motor System” in the “Accessories” section).

Parts supplied

Remove parts from packages. Check that all parts are included.

3 metal grease lters

Hood liner with LED lamps installed.

1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct

transition with damper.

4 - 5 x 45 mm mounting screws

4 - 4.2 x 8 mm screws

T-20 TORX

®†

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualied technician install the hood liner. It is the

installer's responsibility to comply with installation clearances

specied on the model/serial rating plate. The model/serial rating

plate is located behind the left lter on the rear wall of the hood

liner.

The hood liner location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening

dimensions that are shown must be used. Given

dimensions provide minimum clearance.

The hood liner must be surrounded by a custom built enclosure

with hood support capable of supporting 75 lb (34 kg).

Grounded electrical outlet is required. See “Electrical

Requirements” section.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured H

ome Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Cabinet Dimensions

IMPORTANT:

Minimum distance “X”: 24" (61 cm) from electric cooking

surfaces.

Minimum distance “X”: 30" (76.2 cm) from gas cooking

surfaces.

Suggested maximum distance “X”: 36" (91.4 cm).

†®TORX is a registered trademark of Saturn Fasteners, Inc.

“X“ bottom

of canopy to

cooking surface

36" (91.4 cm) for 36" models

48" (121.9 cm) for 48" models

Hood support must be

capable of supporting

75 lb (34 kg)

22" (55.9 cm)

Hood liner depth

Product Dimensions

Venting Requirements

■ Vent system must terminate to the outdoors.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

Typical Internal Blower Motor System Venting Installations

A 10" (25.4 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 10" (25.4 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through the wall, a 90° elbow is needed.

10¹⁄₈" (25.7 cm)

27⁵⁄₈" (70.1 cm)

29¹³⁄₁₆" (75.8 cm)

35⁷⁄₈" (91.1 cm) for 36" models

47⁷⁄₈" (121.6 cm) for 48" models

4¹³⁄₁₆" (12.2 cm)

12³⁄₈"

(31.4 cm)

11¹⁄₂"

(29.2 cm)

5¹⁄₁₆"

(12.8 cm)

22" (55.9 cm)

11" (27.9 cm)

18" (45.7 cm) for 36" models

24" (61.0 cm) for 48" models

Roof Venting Wall Venting

A. 10" (25.4 cm) round vent

B. Roof cap

A. 10" (25.4 cm) round vent

B. Wall cap

Typical In-line Blower Motor System Venting Installations

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

The maximum equivalent vent lengths are:

10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

The following example falls within the maximum recommended

vent length.

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

A. 10" (25.4 cm) round vent

B. Mount on top of ceiling joists.

C. Roof caps

D. Plywood (optional for some installations)

E. Mount on underside of roof rafters.

F. Mount from cross-members tied to trusses.

G. Duct horizontal; mount to cross-members

tied to trusses.

H. Wall cap

Vent Piece Equivalent Length

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■ Hood liner is to be installed 24" (61.0 cm) minimum for

electric cooking surfaces, 30" (76.2 cm) minimum for gas

cooking surfaces, to a suggested maximum of 36" (91.4 cm)

above the cooking surface.

■ Check that all installation parts have been removed from the

shipping carton.

1. Disconnect power.

2. Determine which venting method to use: roof or wall exhaust.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

4. Using 2 or more people, lift hood liner onto covered surface.

5. Remove the filters. See the “Range Hood Care” section.

Hood Liner Support Preparation

1. Mark the locations for the four ¹⁄₈" (3 mm) diameter holes on

the hood support as shown.

2. Using a ¹⁄₈" (3 mm) drill bit, drill the 4 holes.

3. Mark the cutout for the rectangular clearance hole for the

upper hood liner housing as shown.

4. Using a jigsaw or keyhole saw, cut out the rectangular

clearance hole for the upper hood liner housing.

Complete Preparation

1. Determine and make all necessary cuts in the wall or roof for

the vent system. Install the vent system before installing the

range hood. See the “Venting Requirements” section.

2. Determine the location where the power supply cable will be

run through the wall.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent

transition with damper to top of the range hood liner using

four 4.2 x 8 mm screws.

6. Remove terminal box cover and set aside.

7. Remove knockout from the top of the vent hood and install a

UL listed or CSA approved ¹⁄₂" (1.3 cm) strain relief.

8. Place the range hood near its mounting position and run the

power supply cable through the strain relief into terminal box

(enough to make connection).

9. Tighten the strain relief screws.

NOTE: Your range hood requires you to purchase either an

internal type or an in-line (external type) blower motor system.

For internal blower systems, there are blower motor mounting

parts in the blower motor installation packet that must be added

to the range hood prior to mounting the range hood to the wall.

See the “Install Range Hood Internal Blower Motor” section and

the instructions supplied with the blower motor.

A. Wall

B. Centerline

C. 6” (15.2 cm)

D. 10

¹⁄₈

” (25.7 cm)

E. 14

¹⁵⁄₁₆

” (38.0 cm)

F. 29

¹³⁄₁₆

" (75.8 cm)

¹⁄₈

(3 mm) hole

diameter

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Wall

B. Centerline

C. 4

¹⁄₂

” (11.4 cm)

D. 13” (33.0 cm)

E. 14” (35.5 cm)

F. 28” (71.1 cm)

G.Hood support

Install Range Hood Liner

The hood liner attaches to the hood support using four mounting

screws and washers.

NOTE: Hood support must be capable of supporting

75 lb (34 kg).

1. Using 2 or more people, lift the hood liner into place.

2. Install the hood liner using four 5 x 45 mm screws to the hood

support and tighten securely.

Install Hood Liner Internal Blower Motor

NOTE: Your hood liner requires you to purchase either an internal

type or an in-line (external type) blower motor system. See

“Blower Motor System” in the “Accessories” section.

The internal blower system can be mounted for top venting or

rear venting. For top venting, the mounting bracket and spring

clip that come with the blower system will mount to the top panel

of the hood liner. For rear venting, the mounting bracket and

spring clip that come with the blower system will mount to the

rear panel of the hood liner.

Prepare the Internal Blower System

IMPORTANT: Perform steps 1-4 before mounting the hood liner.

1. Remove grease filters from hood liner. See the “Range Hood

Care” section in the Use and Care Guide.

2. Install the motor support bracket using three 4.2 x 8 mm

screws. Screw bracket to the inside top or back (alternate

location on some models), toward the left side of the hood

liner.

3. Install motor spring clip using two 4.2 x 8 mm screws. Screw

spring clip to the inside top or back (alternate location on

some models) of the hood liner at the proper location for the

selected motor system. Slide the mounting tab of the spring

clip through the slot in the panel and secure with the screws.

Use the inside set of mounting holes for the single motor

system. Use the outside set of mounting holes for the dual

motor system.

4. Install the 6 mm nuts to the outside top or outside back

(alternate location on some models) of the hood liner at the

proper location for the selected motor system.

■ Two 6 mm nuts are required for the single motor system.

Clip nuts into the small square notches located at the left

and right end of the square vent opening.

■ Five 6 mm nuts are required for the dual motor system.

Clip nuts into the small square notches, one located in the

front of the square vent opening and the other four

located at the left and right ends of the square vent

opening.

5. Mount hood liner. See the “Install Range Hood Liner” section.

A. 4.2 x 8 mm screws (3) for motor support bracket

B. 4.2 x 8 mm screws (2) for motor spring clip

C. Motor support bracket

D. Motor spring clip (single motor assembly location)

E. Motor spring clip (dual motor assembly location)

A. Clip nut (6 mm) locations for dual motor assembly (quantity 5)

B. Clip nut (6 mm) locations for single motor assembly (quantity 2)

Install Hood Liner Internal Blower Motor

1. Install the hood liner blower motor assembly inside the hood

liner canopy with the wiring connection to the left for the

single motor system and to the front or top for the dual motor

system.

Single Blower Motor Assembly

Dual Blower Motor Assembly

2. Slide the left mounting plate flange under the motor mounting

bracket.

3. Run the power supply wires and connector from the range

hood through the hole in the right end of the motor mounting

plate.

4. Push the right end of the motor mounting plate up and snap it

into the spring tab.

NOTE: The spring tab should be outside the slot in the

mounting plate.

5. Align mounting holes in motor mounting plate with motor

mounting clip nuts and install 6 x 16 mm screws and

6.4 mm lock washers (quantity 2 for single motor; quantity 5

for dual motor).

A. Wiring connection

A. Motor mounting bracket

B. Mounting plate left flange

A. Motor mounting plate hole

B. Power supply wires and connector

A. Motor mounting plate

B. Spring clip

A. Screw with lock washer

B. Mounting hole in motor mounting plate

C. Clip nut (6 mm)

6. Attach power cord connector from the range hood to

connector on wiring box.

7. Go to the “Make Electrical Power Supply Connection to Hood

Liner” section.

Install Hood Liner In-Line (External Type)

Blower Motor

NOTE: Your hood liner requires you to purchase either an internal

type or an in-line (external type) blower motor system. See

“Blower Motor System” in the “Accessories” section.

Prepare for Mounting the In-Line Blower System

The in-line blower system must be fastened to a secure structure

of the roof, ceiling, wall, floor, or new or existing frame

construction. The 4 holes on either the inlet (bottom) side or the

outlet (top) side of the blower must be used to mount the in-line

blower system to the structure.

NOTE: The mounting hole locations must span the studs.

Additional stud framing may be required. Plywood may be used

to span open areas between ceiling joists or roof rafters to aid

installation. This structure must be strong enough to support the

weight of the in-line blower system (50 lb [22.6 kg] min).

Prepare the In-line Blower System

1. Using two or more people, move the in-line blower motor

system to the mounting location.

2. Remove the 10 screws from the front cover of the in-line

blower motor housing and set them aside.

3. Remove the front cover of the in-line blower motor housing

and set it aside.

NOTE: To make the blower motor housing easier to mount, the

blower motor assembly can be removed. If you do not want to

remove the blower motor assembly, proceed to “Install In-line

Blower System” in this section.

4. Disconnect the motor electrical plug from the blower motor

assembly.

5. Remove the screws that secure the blower motor assembly

to the in-line blower housing and set them aside.

6. Pull the spring clip to release the blower motor assembly.

Remove the blower motor assembly from the housing and

place it on a covered surface.

Install In-line Blower System

NOTE: The blower motor housing can be mounted using 4 holes

from either the inlet side or the outlet side of the blower.

1. Position the in-line blower motor housing in its mounting

location and mark the 4 mounting hole locations.

2. Drill 4 mounting pilot holes using a ³⁄₁₆" (5 mm) drill bit.

3. Attach the in-line blower motor housing to the mounting

location with four 6 x 80 mm mounting screws and washers.

4. If it is removed, reinstall the blower motor assembly and

secure it with the screws previously removed.

5. If it is removed, reattach the motor electrical plug to the

connector on the blower motor assembly.

A. Wiring box connector

B. Power supply connector

from range hood

WARNING

Excessive Weight Hazard

Use two or more people to move and install in-line

blower motor system.

Failure to do so can result in back or other injury.

A. Front cover

B. Blower mounting screws

C. Spring clip

D. Bottom housing mounting holes

E. Motor electrical plug

A. Mounting holes

Outlet Side

Inlet Side

Complete Preparation

1. Determine and make all necessary cuts for the vent system.

IMPORTANT: When cutting or drilling into the ceiling or wall,

do not damage electrical wiring or other hidden utilities.

2. Determine the location where the ¹⁄₂" (1.3 cm) wiring conduit

will be routed through the ceiling or wall between the in-line

blower and the hood liner.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4. Locate the electrical terminal boxes in the in-line blower

housing and hood liner. Remove the terminal box covers and

set the covers and screws aside.

5. Remove the electrical knockout from the in-line blower

housing and hood liner to prepare for the installation of the

UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit and

conduit connector.

6. With the hood liner mounted (see the “Install Hood Liner”

section), run the ¹⁄₂" (1.3 cm) wiring conduit between the in-

line blower motor housing and the hood liner. Pull enough

¹⁄₂" (1.3 cm) wiring conduit to allow for easy connection to the

terminal boxes in the in-line blower housing and hood liner.

7. Run the six 18 AWG wires through the ¹⁄₂" (1.3 cm) wiring

conduit and conduit connectors and into the terminal boxes

on the in-line blower housing and hood liner. Leave enough

wire length in each terminal box to make the wiring

connections.

8. Install the conduit connectors and conduit to the in-line

blower housing and hood liner electrical terminal boxes.

9. Connect the vent system to the hood liner and in-line blower

system and seal all joints with clamps.

Make Electrical Connections for In-Line

Blower Motor System

Electrical Connection Inside In-line Blower System

1. Disconnect power.

2. Connect the wires from the wiring conduit to the wires from

the motor electrical plug cable inside the in-line blower

housing terminal box.

3. Use UL listed wire connectors and connect the black wires

4. Use UL listed wire connectors and connect the white wires

(D) together.

5. Use UL listed wire connectors and connect the red wires (E)

together.

6. Use UL listed wire connectors and connect the blue wires (F)

together.

7. Use UL listed wire connectors and connect the gray wires (G)

together.

A. Electrical terminal box

B. Electrical knockout

A. UL listed or CSA approved

¹⁄₂

" (1.3 cm) wiring conduit

B. UL listed wire connectors

C.Black wires

D. White wires

E. Red wires

F. B l u e w i r e s

G. Gray wires

H. Green (or yellow/green)

and green/yellow wires

I. Motor electrical plug cable

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

8. Connect the green (or yellow/green) ground wire to the

green/yellow ground wire (H) in the terminal box using UL

listed wire connectors.

9. Reinstall the in-line blower terminal box cover and screw.

10. Reinstall the front cover of the in-line blower housing and

secure it with 10 mounting screws.

Electrical Connection Inside Hood Liner Between In-line

Blower System and Hood Liner

1. With the hood liner mounted (see the “Install Hood Liner”

section), locate the wiring cable connector inside the hood

liner.

2. Connect the 6-wire connector assembly supplied with the

in-line blower motor system to the mating cable connector

from the hood liner.

3. Locate the terminal box inside the hood liner and install a

¹⁄₂" (1.3 cm) UL listed or CSA approved strain relief (see

“Complete Preparation” in the “Prepare Location” section).

4. Run the wire ends from the 6-wire connector assembly

through the ¹⁄₂" (1.3 cm) strain relief, leaving enough wire

length to make the wiring connections. Tighten the strain

relief screws.

5. Connect the wires from the 6-wire connector assembly to the

wires from the wiring conduit inside the hood liner terminal

box.

6. Connect the same color wires to each other (black to black,

white to white, etc.) using UL listed wire connectors.

NOTE: Connect the green (or green/yellow) ground wire from

the wiring conduit to the green (or bare) ground wire from the

home power supply using UL listed wire connectors (see the

“Make Electrical Power Supply Connection to Hood Liner”

section).

7. Go to the “Make Electrical Power Supply Connection to Hood

Liner” section.

Make Electrical Power Supply Connection

to Hood Liner

1. Disconnect power.

2. Locate terminal box inside of the hood liner.

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. UL listed or CSA approved

¹⁄₂

" (1.3 cm) wiring conduit

B. UL listed wire connectors

C. Black wires

D. White wires

E. Red wires

F. B l u e w i r e s

G. Gray wires

H. Green (or green/yellow)

wire

I. 6-wire connector assembly

A. Terminal box cover

B. Terminal box

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

3. Use UL listed wire connectors and connect black wires (B)

together.

4. Use UL listed wire connectors and connect white wires (A)

together.

NOTE: When using an In-line blower motor system, the green (or

green/yellow) ground wire in the conduit from the In-line blower

motor system is to be connected with the green (or bare) wire of

the home power supply cable and with the green/yellow wire (D)

in the terminal box.

5. Connect green (or bare) ground wire from

home power supply

to the green/yellow ground wire (D) in terminal box using UL

listed wire connectors.

6. Install terminal box cover.

7. Check that all light bulbs are secure in their sockets.

8. Reconnect power.

Complete Installation and Check

Operation

1. Install grease filters. See the “Range Hood Care” section.

2. Check operation of the range hood blower and lights. See the

“Range Hood Use” section.

3. If the range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power supply and check that the wiring is

correct.

NOTE: To get the most efficient use from your new hood liner,

read the “Range Hood Use” section.

A. White wires

B. Black wires

C. UL listed wire connectors

D. Green, bare or yellow/green wires

E. Home power supply

F. UL listed or CSA approved

¹⁄2

" (1.3 cm) strain relief

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. LED lights

B. LED light switch

C. Blower control switches

D. Grease filter handle

E. Grease filter

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The hood controls are located on the underside of the range

hood.

Range Hood Controls

Operating the light

1. Move the light switch to the “1” position to turn range hood

light to night light setting.

2. Move the light switch to the “2” position to turn range hood

light to full light setting.

3. Move the light switch to the “Off” position to turn range hood

light OFF.

Operating the fan

1. Move the fan switch to the “On” position to turn the fan ON.

The fan will begin operating at the speed set on the fan speed

switch.

2. Move the fan switch to the “Off” position to turn the fan OFF.

Auto On Fan

The range hood is equipped with a sensor to automatically turn

on the fan when excessive heat is detected in the control area.

When the fan switch is in the “Off” position, this sensor will turn

the fan to high speed when necessary. When the heat decreases,

the fan will turn off.

When the fan switch is in the “On” position, the heat sensor is not

active and the range hood functions normally.

Adjusting the fan

The fan has 3 speed controls. Move the fan speed switch to “1”

position for low speed, “2” position for medium speed, or “3”

position for high speed.

Thermal Protector

The range hood is equipped with a thermal protector to avoid

overheating conditions. If the range hood shuts off while in use,

move fan slider switch to Off to turn off the range hood. Wait

approximately 60 minutes, then move slider to On to restart the

range hood.

A. Light control

B. Blower control

C. Fan speed control

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

Liquid detergent soap and water, or all-purpose cleanser

Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filter:

1. Remove each filter by pulling the spring release handle and

then pulling down the filter.

2. Wash metal filters as needed in dishwasher or hot detergent

solution.

3. Reinstall the filter by making sure the spring release handles

are toward the front. Insert aluminum filter into upper track.

4. Push in spring release handle.

5. Push up on metal filter and release handle to latch into place.

6. Repeat steps 1-5 for the other filter.

Replacing a LED Lamp

Turn off the range hood and allow the LED lamp to cool. To

avoid damage or decreasing the life of the new lamp, do not

touch lamp with bare fingers. Replace lamp, using tissue or

wearing cotton gloves to handle lamp.

If new lamps do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Push up on the lens and turn it counterclockwise.

3. Remove the lamp and replace it with a 120-volt, 6.5-watt

maximum LED

lamp with a GU10 base. Turn it clockwise

to lock it into place.

4. Repeat steps 2-3 for the other lamp if needed.

5. Reconnect power.

A. Spring release handle

WIRING DIAGRAM

LED LED LED LED

SE112B

Junction box

Gnd

Y-G

Temperature

sensor

Closure

temperature:

167˚F±5.4˚F

(75+/-3˚C)

Opening

temperature:

≥

140˚F (60˚C)

Fan speed

On Off On Off

Off

Fan

Light

Speed 1

Speed 2

Speed 3

Y-G

25uF

Y/G

W W

Lamps

Optional kit with 1 motor

Motor Resistance (Ohms)

Switch operation with button "1-2-3"

Position

Connection

Action

Switch operation with button "ON-OFF"

Position

Connection

Action

Position

Connection

Action

Switch operation with button "Light"

Motor Characteristics

Blue-Red: 18

Blue-Gray: 14.3

Blue-White: 21.6 (min.)

Room Temp: 73.4˚F (23˚C)

Blue-Black: 9.8 (max)

2 4

Speed 1

Speed 2

Speed 3

Motor ON

Motor OFF

OFF

2 4

Power supply: 120 VAC

Frequency: 60 Hz

Power absorption: 420 W

Current: 3.7A

Lights Off

Low

Intensity

High

Intensity

ASSISTANCE OR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

In the U.S.A.

Call the Whirlpool Customer eXperience Center

toll free: 1-800-253-1301.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

■ Referrals to local dealers, repair parts distributors and service

companies. Whirlpool designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer eXperience Centre

Whirlpool Canada LP

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Stainless Steel Grease Filter - kit contains 1 filter

Order Part Number W10351855

Order quantity 3 for 36" (91.4 cm) model

Order quantity 4 for 48" (121.9 cm) model

Blower Motor Systems (1 system is required)

NOTE: Internal Blower Motor Systems: UXB0600DYS - 600 CFM

Internal Blower Motor System is for use in the 36" hood liner

above a cooktop with a maximum of 65,000 Btus.

Use UXB1200DYS - 1200 CFM Internal Blower Motor System

above cooktops rated higher than 65,000 Btus or with the 48"

hood liner.

600 CFM Internal Blower Motor System - Order Model Number

UXB0600DYS

1200 CFM Internal Blower Motor System - Order Model Number

UXB1200DYS

600 CFM In-Line Blower Motor System - Order Model Number

UXI0600DYS

1200 CFM In-Line Blower Motor System - Order Model Number

UXI1200DYS

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

■ Utiliser cet appareil uniquement dans les applications

envisagées par le fabricant. Pour toute question, contacter

le fabricant.

■ Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre l'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour empêcher tout rétablissement accidentel de

l'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une étiquette d'avertissement proéminente

interdisant le rétablissement de l'alimentation.

■ Tout travail d'installation ou câblage électrique doit être

réalisé par une personne qualifiée, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du bâtiment et de protection contre les

incendies.

■ Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommagé(e). Jeter le ventilateur ou le retourner

à un centre de service agréé pour examen et/ou réparation.

■ Une source d'air de débit suffisant est nécessaire pour le

fonctionnement correct de tout appareil à gaz (combustion

et évacuation des gaz à combustion par la cheminée), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de l'équipement de chauffage et

les prescriptions des normes de sécurité - comme celles

publiées par la National Fire Protection Association (NFPA)

et l'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorités réglementaires locales.

■ Lors d'opérations de découpage et de perçage dans un mur

ou un plafond, veiller à ne pas endommager les câblages

électriques ou canalisations qui peuvent s'y trouver.

■ Les ventilateurs d'évacuation doivent toujours décharger

l'air à l'extérieur.

MISE EN GARDE : Cet appareil est conçu uniquement

pour la ventilation générale. Ne pas l'utiliser pour l'extraction

de matières ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et évacuer adéquatement les gaz, veiller à acheminer l'air

aspiré par un conduit jusqu'à l'extérieur - ne pas décharger

l'air aspiré dans un espace vide du bâtiment comme une

cavité murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MÉTALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE :

■ Ne jamais laisser un élément de surface fonctionner à

puissance de chauffage maximale sans surveillance. Un

renversement/débordement de matière graisseuse pourrait

provoquer une inflammation et la génération de fumée.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

■ Veiller à toujours faire fonctionner le ventilateur de la hotte

lors de la cuisson avec une puissance de chauffage élevée

ou lors de la cuisson d'un mets à flamber (à savoir crêpes

Suzette, cerise jubilée, steak au poivre flambé).

■ Nettoyer fréquemment les ventilateurs d'extraction. Veiller à

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

■ Utiliser toujours un ustensile de taille appropriée. Utiliser

toujours un ustensile adapté à la taille de l'élément

chauffant.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRÈS LE DÉCLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :

■ Placer sur le récipient un couvercle bien ajusté, une tôle à

biscuits ou un plateau métallique POUR ÉTOUFFER LES

FLAMMES, puis éteindre le brûleur. VEILLER À ÉVITER

LES BRÛLURES. Si les flammes ne s'éteignent pas

immédiatement, ÉVACUER LA PIÈCE ET APPELER LES

POMPIERS.

■ NE JAMAIS PRENDRE EN MAIN UN RÉCIPIENT

ENFLAMMÉ - vous risquez de vous brûler.

■ NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brûlante.

■ Utiliser un extincteur SEULEMENT si :

– Il s'agit d'un extincteur de classe ABC, dont on connaît le

fonctionnement.

– Il s'agit d'un petit feu encore limité à l'endroit où il s'est

déclaré.

– Les pompiers ont été contactés.

– Il est possible de garder le dos orienté vers une sortie

pendant l'opération de lutte contre le feu.

Recommandations tirées des conseils de sécurité en cas

d'incendie de cuisine publiés par la NFPA.

■ AVERTISSEMENT : Pour réduire le risque d'incendie

ou de choc électrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de réglage de la vitesse à semi-

conducteurs.

La page est en cours de chargement...

Whirlpool UVL6036JSS Mode d'emploi

Marque: Whirlpool

Modèle: UVL6036JSS

Catégorie: Hottes

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool UVL6036JSS User guide

Documents connexes

Maytag 48" Manuel utilisateur

Whirlpool UVL6036JSS Mode d'emploi

Whirlpool UVL6036JSS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents