HeatStar HEATSTAR HS4000 NG Le manuel du propriétaire

Marque: HeatStar

Modèle: HEATSTAR HS4000 NG

Catégorie: Chauffe-eau

Taper: Le manuel du propriétaire

Ce manuel convient également à

OPERATING INSTRUCTIONS AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read

and follow all instructions. Place instructions in

a safe place for future reference. Do not allow

anyone who has not read these instructions to

assemble, light, adjust or operate the heater.

MODEL

HS4000 NG/LP

08/11 50401

ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001

DIRECT FIRED HEATER

HEATSTAR

BY ENERCO

If the information in this manual is not followed exactly, afire or explosion

may result causing property damage, personal injury or loss of life.

WARNING:

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

— Service must be performed by a qualified service agency.

This is a vented portable heater. It uses air (oxygen) from the area in which it is used. Adequate

combustion air and ventilation must be provided. Refer to page 5.

NATURAL GAS/LPG FIRED

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

WARNING :

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.

KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MA -

TERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE

AWAY FROM THE HEATER AS RECOMMENDED BY TH E

INSTRUCTIONS NEVER USE THE HEATER IN SPAC ES

WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE

COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,

SOLVENTS, PAINT THINNER, DUST PARTICLES OR UN-

KNOWN CHEMICALS.

WARNING :

COMBUSTION BY-PRODUCTS PRODUCED WHEN US -

ING THIS PRODUCT CONTAIN CARB ON MONOXIDE,

A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER AND BIRTH D EFECTS (OR OTHER

REPRODUCTIVE HARM).

GENERAL HAZARD WARNING :

FAILURE TO COMPLY WITH THE PRECAUTIONS AND

INSTRUCTIONS PROVIDED WITH THIS H EATER, CAN

RESULT IN DEATH, S ERIOUS BODILY INJURY AND

PROPERTY LOSS OR DAMAG E FROM HAZARDS OF FIRE,

EXPLOSION, BURN, ASPHYXIATI ON, CARBON MONOX-

IDE POISONING, AND/ OR ELECTRICAL SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW

THE INSTRUCTIONS SHOULD USE OR SERVICE THIS

HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION

SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.

CONTACT THE MANUFACTURER.

WARNING :

NOT FOR HOME OR RECREATIONAL VEHICLE USE

WARNING :

YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,

SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU

OPERATE THIS HEATER.

The State of California requires the following warning:

CONTENTS

WARNINGS .................................................................................. 2-3

SPECIFICATIONS ........................................................................... 4

OPERATION ................................................................................. 5

SAFETY DEVICES .......................................................................... 4

MAINTENANCE ............................................................................ 5

VENTILATION ............................................................................... 5

TROUBLESHOOTING .................................................................... 6

WIRING DIAGRAMS ..................................................................... 7

PARTS LIST .............................................................................11-16

WARNING :

READ THE INSTRUCTIONS GIVEN IN THIS

MANUAL BEFORE USING THE APPLIANCE .

•DO NOT USE GASOLINE, NAPHTHA OR VOLATILE

FUELS.

• THE ELECTRICAL SYSTEM TO WHICH THE APPLIANCE

IS CONNECTED MUST C OMPLY WITH A LL SAFETY

REGULATIONS IN FORCE. A R ESIDUAL CURRENT

CIRCUIT BREAKER MUST B E PROVIDED ON THE MAIN

DISTRIBUTION BOARD.

• UNPLUG THE HEATER BEFORE ATTEMPTING ANY

SERVICE OR MAINT ENANCE.

• ALWAYS CHECK THE POWER SUPPLY CABLE BEFORE

USE. IT MUST N OT BE BENT, CRUSH ED, OR ANYWAY

DAMAGED.

• THE POWER SUPPLY CABLE MUST BE REPLACED ONLY

BY QUA LIFIED PERSONNEL.

• ONLY USE AN ORIGINAL H07RN-F POWER CABLE

WITH WAT ERPROOF PLUG.

• DO NOT TOUCH THE EXHAUST GAS OUTLET. DANGER

OF BURNS!

IMPORTANT

Before using the heater, read and understand all instructions and

follow them carefully. The manufacturer is not responsible for

damages to goods or persons due to improper use of units.

3Operating Instructions and Owner’s ManualENERCO GROUP, INC. |Indirect Fired Portable Heater

The heater is designed and approved for use as a construction heater in accordance with Standard

ANSI Z83,7 CGA 2.14.

CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT

APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in specific

applications.Your local authority can advise you about these.

This heater can be washed, provided that:

A. The heater is disconnected from the electrical supply.

B. All access panels are securely closed.

C. Water spray nozzle shall not discharge within 6 feet of the heater.

D. The heater is not reconnected to electrical supply until thoroughly dried.

Improper cleaning of the heater can cause severe personal injury or property damage due to water

and/or cleaning solutions:

A. In electrical components, connections and wires causing electrical shocks or component

failure.

B. On gas control components causing corrosion which can result in gas leaks and fire or

explosion from the leak.The hose assembly must be protected from the traffic, building

materials and contact with hot surfaces both during use andwhile in storage.

Proper gas supply must be provided to the inlet of the appliance.

Refer to rating plate for proper gas supply pressure.

Gas pressure in excess of maximum inlet pressure specified at the appliance inlet can cause fire or

explosions, leading to serious injury, death, building damage or loss of livestock.

Likewise, gas pressure below the minimum inlet pressure specified at the appliance inlet may cause

improper combustion,leading to asphyxation, carbon monoxide poisoning and therefore serious

injury or death to humans and livestock.

Position heater properly before use.

For either indoor or outdoor use adequate ventilation must be provided.

Minimum clearance from combustible materials and propane containers: 10 ft.

Do not operate heater with panels removed.

Not for use with ductwork.

To avoid injury from moving parts, disconnect all electrical power to equipment before opening

doors or removing panels.

RETAIN THIS INSTRUCTION FOR FUTURE REFERENCE. .

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE INJURY OR DEATH.

READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

WARNING :

TECHNICAL SPECIFICATIONS GE/N 250C GE/N 400C

Natural gas

Supply pressure [in WC] min 7" w.c.

max 10" w.c. min 7" w.c.

max 10" w.c.

Selector valve position

Normal

altitude 0 -

2,000 ft above

sea level

(U.S.A. and

Canada)

Heat input [BTU/h] 254.684403.753

Manifold pressure [in WC] 4,33 4,40

Fuel consumption [CFH] 241,52 381,35

Altitude 2,000

- 4,500 ft

above sea

level (Canada

only)

Heat input [BTU/h] 229.216363.378

Manifold pressure [in WC] 4,11 4,18

Fuel consumption [CFH] 217,37 343,21

L.P.G.

Supply pressure [in WC] min 8" w.c.

max 13" w.c. min 8" w.c.

max 13" w.c.

Selector valve position

Normal

altitude 0 -

2,000 ft above

sea level

(U.S.A. and

Canada)

Heat input [BTU/h] 241.413394.134

Manifold pressure [in WC] 4,28 4,50

Fuel consumption [CFH] 88,98 145,12

Altitude 2,000

- 4,500 ft

above sea

level (Canada

only)

Heat input [BTU/h] 217.272354.721

Manifold pressure [in WC] 4,06 4,27

Fuel consumption [CFH] 80,08 130,61

Air flow [cfm] 2.766 4.120

Power supply

Phase 1 1

Voltage [V] 120120

Frequency [Hz] 60 60

Electric consumption [W] 500900

[A] 5,0 8,5

Ring nozzle [in] N. 16 holes x 0,079" N. 16 holes x 0,102"

Gas inlet connection thread 3/4" NPT 3/4" NPT

Air distribution

duct

Max Static pressure [in] 0,60 0,56

Max length [ft] 50 50

Noise level at 1 m [dBA] 77 74

Heater Dimensions, L x W x H [in] 40,6 x 24,6 x 21,7 56,,1 x 29,5 x 25,7

Weight [lb] 101192

Packaging Dimensions, L x W x H [in] 42,3 x 21,9 x 29,45 57,7 x 24,4 x 32,6

Weight [lb] 134225

4Operating Instructions and Owner’s ManualENERCO GROUP, INC. |Indirect Fired Portable Heater

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

CONTROL PANEL - TABLEAU DE COMMANDE

Fig. 1

1COMBUSTION CHAMBER

2BURNER

3DIFFUSION RING

4FLAME GUARD SHIELD

5COOLING FAN

6IONIZATION ELECTRODE

7IGNITION ELECTRODE

8CONTROL FLAME ELECTRONIC RESET

9HEATING SWITCH

10 ROOM THERMOSTAT PLUG

11 POWER CONTROL LAMP

12 POWER CORD

13 VENTILATION MODE SWITCH

14 PHASE / NEUTRAL LINE TEST PUSH BUTTON

MANIFOLD ASSEMBLY

GE/N 250 GE/N 400

Fig. 2

aGAS SELECTOR VALVE

bMANIFOLD PRESSURE PORT (MANIFOLD)

cMANIFOLD PRESSURE REGULATOR

dMAIN GAS VALVE

eINLET PRESSURE PORT

fSHUT OFF / FIRING VALVE

4 1 6 3 2 7 5

6Operating Instructions and Owner’s ManualENERCO GROUP, INC. |Indirect Fired Portable Heater

DESCRIPTION

The hot air generator is designed for heating medium and large

ventilated premises, for which a fixed or mobile heating system is

required.

Heater is to be run on heating with natural gas or L.P.G. according

to gas supply pressures that must be in conformity with the national

laws.

Gases to be used are indicated in Tab. I together with the supply

pressures, the regulation of the gas valves group (burner pressure)

and gas flow.

Heater is supplied after a complete functional test and it’s therefore

prearranged for one of the working gas indicated in Tab. I: an

adhesive label applied on the gas selector valve (a) indicates the

selected gas.

To change the type of gas, follow the detailed instructions

indicated in section “CHANGING TYPE OF GAS”.

The heater is of the direct combustion type. The air is heated by

the energy developed during combustion and then conveyed to the

environment to be heated together with the combustion products,

thus making available 100% of the thermal power produced. The

environment must be suitably ventilated in order to ensure adequate

air circu-lation.

In the event of serious malfunction various safety devices

(electronic flame control unit, overheating thermostat, air pressure

switch) trigger turning off the heater .

The electronic flame control unit monitors if the flame is irregular or

goes out, the safety thermostat triggers when the temperature in the

combustion chamber exceeds the safety limit value, the air pressure

switch will cut in if the airflow is insufficient.

In each of the said cases the unit stops according to the procedure

described in “OPERATING INSTRUCTIONS”.

In each of the said cases the lamp (8) will light up and the heater

will stop working. The heater can be restarted only by pressing the

reset button (8). Nonetheless, the cause that triggered the safety

device should always be carefullyanalyzed and resolved before

restarting the generator (cfr. “FAULTS, CAUSES AND REMEDIES”).

GENERAL ADVICES

Installation, setting and use of the heater must be effected in

accordance with the applicable regulations and laws relating to

machine use.

Check with yourlocal fire safety authority if you have

questions about applications

Here are a few guidelines which shall be followed:

•The instructions in this manual are carefully followed;

•Minimum clearances from combustible material must be:

1 m (3 feet) from side and rear (air inlet) of heater

0.7 m(2 feet) from ceiling

3 m (10 feet) on air outlet of heater.

•Heater shall not be directed toward any propane-gas container

within 6 m (20 feet) and minimum clearances from gas cylinder

must be 3 m (10 feet)

•Don’t install the heater in places where there may be a risk of fire

or explosion

•All fire prevention regulations must be adhered to.

•For air distribution use only original ductworks type M1 Spiraflex

from distributor and respect max length as declared in Tab. I

•The room or building which is being heated must be sufficiently

ventilated so that the heater has enough air to function properly;

•The air suction and/or supply pipes are not blocked in any way,

there are not sheets or covers resting on the machine or walls

and bulky objects near the heater;

•The generator is placed near a power switchboard having

specifications in conformity with those declared;

•The unit is placed in a fixed position;

•The generator is regularly monitored during operation and

checked before being started up;

•Don’t let animals or children near the heater.

•Make sure heater is inspected before each use, and at least

annually by a qualified service person.

•After use make sure the disconnecting switch is off.

When using any type of heater it is obligatory:

•not to exceed the maximum level of heat output of the furnace

(“TECHNICAL SPECIFICATION TABLE”);

•to make sure that there is adeguate air circulation and air supply

to the heater and that nothing is obstructing the aspiration and

expulsion of air; movement of air may be obstructed in various

ways including placing covers or other objects on the heater or

positioning the heater too near a wall or other large object. If the

airflow is not adequate, the combustion chamber will overheat

and the overheat thermostat will turn the burner off

(“OBSERVED FAULTS, CAUSES AND REMEDIES”).

INSTALLATION INSTRUCTION

All the operations described in this paragraph must

be performed by professional and skilled personnel

only

The installation shall be in accordance with National Fuel Gas

Code ANSI Z223.1/NFPA 54 and with CAN1-B149.1 Installation

code.

An approved manual gas valve shall be provided by the installer.

In case of installation in greenhouses, mechanical

ventilation shall be interlocked to the heater operation

or permanent openings shall be fixed for ventilation

air.

ELECTRICAL CONNECTIONS

The power line of the generator must feature an

earthlead and a residual current circuit breaker.

The supply cable must be connected to a switchboard

with sectioning switch.

Every heater is supplied along with the safety and control devices

which are indispensable to the correct functioning of the unit being

already electrically connected.

When installed, the appliance must be electrically

grounded in accordance with local codes, or in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70, and/or the CSA C22.1, Canadian

Electrical Code, if an external electrical source is

utilized.

The following operations must now be carried out:

•Plug in the power cord having read the rating plate that specify

electric supply characteristics.

•Connect accessories such as the room thermostat or clock to the

unit’s control panel with the thermostat receptacle.

Having completed all these operations check carefully that all

electrical connections correspond to the wiring diagram. When the

heater is first turned on you must check that the fan does not use

more current than the maximum permitted limit.

GAS LINE CONNECTIONS

The connection to the gas feed pipe, whose sizes must correspond

to the kind of system to be made, must be carried out by placing the

“gas ramp” as indicated in Fig. 3: the gas pipe, the interception tap

and the anti-vibration joint are not supplied with the heater and they

must be arranged by the person in charge of installation.

WARNING :

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

1 Main gas pipe 3 Antivibrating coupling

2 Manual shut-off valve 4 Gas valves group

Fig. 3

In case of connection of heater to natural gas, the installation shall

conform with local codes or, in the absence of local codes, with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 and the Natural Gas

and Propane Installation Code, CSAB149.1.

In case of connection to a propane supply cylinder:

(a) the installation must conform with local codes or, in the

absence of local codes, with the Standard for the Storage and

Handling of Liquified Petroleum Gases, ANSI/NFPA 58 and the

Natural Gas and Propane Installation Code, CSA B149.1.

(b) to determine size and capacity of the cylinder(s) and for any

specific requirements consult your LP gas supplier. In any case

propane tank should not be lower than 100 lb (90 liters)

vapour withdrawal from the operating cylinder;

(d) the gas shall be turned off at the propane supply cylinder when

the heater is not in use;

(e) when the heater is to be stored indoors, the connection

between the propane supply cylinder and the heater must be

disconnected and the cylinders removed from the heater and

stored in accordance with Standard for the Storage and

Handling of Liquified Petroleum Gases, ANSI/NFPA 58 and

CSA B149.1, Natural Gas andPropane Installation Code.

The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system

by closing its individual manual shut-off valve during any pressure

testing of the gas supply piping system at test pressures equal or

less than 1/2 psi (3.5 kPa).

A minimum 1/8” NPT plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of the gas

supply connection to the appliance.

STARTUP

The heater is supplied after a complete functional test and it’s

therefore prearranged for one of the gas (natural or L.P.G.) indicated

in Tab. I: an adhesive label applied on the manual gas selector valve

(Fig. 4) indicates the working gas (usually it’s natural gas). Should it

necessary to change the kind of gas (from natural gas to L.P.G or

viceversa) follow the detailed instructions indicated in section

“CHANGING TYPE OF GAS”.

Only when the heater has been prearranged according to the

proper working gas it will be possible to carry out the following

operations:

• Leak away some gas from the feed pipe;

• Check that the pipe is gas proof;

• Open the gas stopcock and start the hot air generator;

For installation in the U.S.A. at elevation above 2,000 feet (610 m),

the appliance shall be derated 4 per cent for each 1,000 feet (305 m)

of elevation above sea level.

For installation in Canada at elevation above 2,000 feet to 4,500

feet above sea level, the heater is deratedy reducing the input for the

appropriate fuel in accordance with the rating plate manifold

pressure.

THE CONVERSION SHALL BE CARRIED OUT BY A

MANUFACTURER’S AUTHORIZED REPRESENTATIVE,

IN ACCORDANCE WITH THE REQUIREMENTS OF THE

MANUGFACTURER, PROVINCIAL OR TERRITORIAL

AUTHORITIES HAVING JURISDICTION AND IN

ACCORDANCE WITH THE REQUIREMENTS OF THE

CAN/CGA-B149.1 OR CAN/CGAB149.2 INSTALLATION

CODES.

A conversion label shall be applied adiacent to the Rating Label:

THIS APPLIANCE HAS BEEN CONVERTED FOR USE

AT AN ALTITUDE OF ___________ FEET (ABOVE 2000 FEET)

Orifice size: ______________________________________

Manifold pressure: ______________________________________

Input rate: ______________________________________

Date of conversion: ______________________________________

Type of fuel: ______________________________________

Converted by: ______________________________________

For installation in Canada at elevation above 4,500 feetabove sea

level, consult Provincial or Territorial Authorities having jurisdiction.

CHANGING TYPE OF GAS

This operation may be carried out several times during the working

life of the machine and not only at initial start-up. Therefore, first of all

check the adhesive label attached to the manual gas selector valve

(a) in Fig. (2) to establish the original category of the gas and then

consult Tab. I to identify the supply pressure, the working pressure,

the use conditions of manual valve.

To change kind of gas it is necessary (Fig. 2):

• to remove the sticker on the manual gas selector valve stating

the gas used at that time,

• to remove the screw under the sticker and turn the manual

handle on the correct side according to the condition described in

Tab.I and by following instruction:

Fig. 4

• After having moved the handle into the opposite position, put

again the fixing screw and a new sticker on it, stating the gas

which has to be used (a number of different stickers are supplied

with the machine)

Burner pressure shall not be adjusted: the heater is

ready to run on the new gas

Should it necessary to check the burner pressure:

• connect a manometer to the pressure port (b) ,

• carry out the pressure reading on the manometer and turn the

pressure regulator (c) if necessary to obtain the correct burner

pressure value indicated in Tab. I

OPERATING INSTRUCTIONS

Any time the power cord of the heaters is connected to

a receptacle check the polarity of power supply:

•check switch (9) and (13) are on “0”

•connect plug to receptacle

•push button (14): if it lights up, then reverse polatiry

If the correspondance of phase / neutral polarity is not

correct, the unit may stop in the reset mode.

HEATING MODE

WARNING :

Turning ON

• Make sure switch (9) is on “0”;

• Power the heater by means of the sectioning switch on the

switchboard;

• If the unit is operated manually (without any thermostat or any

other control device) turn the switch (9) to position “1”. The

burner starts up, the combustion chamber heats up and then the

fan starts;

• If the unit operates automatically (being connected to any

thermostat or any other control device) turn the switch (9) to

position “1” and set the room thermostat at the desired level: the

heater will now start and stop automatically.

• If after these operations, the generator does not work, refer to the

“FAULTS, CAUSES AND REMEDIES” paragraph and find the

cause.

Setting Post Ventilation Mode

By the switch (13) on control panel, select the post-ventilation

mode, that is the time the fan goes on blowing air when unit is

switched off:

• when switch (134) is on pos. “0” then postventilation lasts for 30

sec.

• when switch (13) is on pos. “1” then postventilation is continuous.

Turning OFF

In manual operation turn switch (9) to “0” or turn thermostat control

knob off.

After switching off the machine, a post ventilation function works

according to the previous setting.

Finally, close the gas supply stopcock, close the shut-

off valve (f) and turn off the sectioning switch (Fig. 1-

2).

VENTILATION MODE

To obtain the ventilation function only, make sure switch (9) is on

position “0” and then simply turn the switch (14) to position “1”. To

stop it, turn the switch “4” to position “O”.

Whichever be the reason, the unit try to restart once.

If the cause of malfunction remain, the unit definitevely

stop and lamp (8) will light up

The heater can be restarted only by pressing the reset button (8).

Nonetheless, the cause that triggered the safety device should

always be carefully analyzed and resolved before restarting the

generator (cfr.“FAULTS, CAUSES AND REMEDIES”).

TRANSPORT AND HANDLING

Before moving the unit:

• Stop the machine as indicated in the “STOP”

paragraph;

• Disengage the power supply by removing the plug

from the power socket;

• Fully unscrew the fitting connecting the gas hose

pipe to the heater;

• Wait for the heater to cool down.

The hot air generators with wheels must be wheeled.

MAINTENANCE

To regulate operation of the unit, the fans, combustion chamber

and the burner must be at least annually inspected and periodically

cleaned by a qualified service person.

Before performing any maintenance operation:

•Stop the machine as indicated in the “STOP”

paragraph;

•Disengage the power supply by removing the plug

from the power socket;

•Close the gas supply stopcock and shut-off valve (f);

•Wait for the heater to cool down.

During cleaning any foreign bodies must be removed from the fan

suction grille.

To access the burner, remove the flame guard panel (4) by

removing the four screws and clean carefully inside the combustion

chamber and the whole burner head: any debris shall be taken away.

Do not direct jets of compressed air towards the air

pressure points near the main fan: the air pressure

switch could be permanently damaged.

Cleaning of the burner shall be regularly performed by qualified

service person. To access the burner, remove the flame guard panel

of combustuion chamber (front side) and clean carefully inside the

combustion chamber and the whole burner head and electrodes.

After cleaning, the flame guard panel of combustion

chamber (4) must be put back in place and secured

with the relative screws before operate the heater.

Operating the heater without the flame guard panel of combustuion

chamber (4) can cause the flame to work with risk to the health of

exposed persons (because of formation of carbon monoxide, CO)

and constituting a danger for the environment.

WARNING :

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

TROUBLESHOOTING GUIDE

FAULTS CAUSES REMEDIES

• The generator fails to start

• No power supply

• Check power specifications

• Check power connections

• Check fuse integrity

• Main switch in wrong position • Select correct position

• Faulty operation of room thermostat

• Check thermostat position

• Check thermostat operation

• Safety device (control unit, safety

thermostat, etc.) not reset after a repair • Press button (1) on the control panel

• The duct gives too much back pressure

and airpressure switch PA1 blocks the

heater

• Reduce back pressure by straightening

the duct or by reducing duct length

• The generator stops and the indicator

light (1) comes on

• Gas pressure switch trips due to

interruption of gas flow (gas pressure

switch electric contact does not close

during operation)

• Make sure the gas supply hose has been

bled

• Check gas supply pressure

• Micro-switch PAM intervention for fan

malfuction

• Make sure the suction and feed grilles

are not blocked

• Make sure the fan is turning properly

• Check the electric motor and capacitor

and, if these are faulty, replace

• The flame sensor is not operating

correctly • Remove the flame sensor and clean

• The safety thermostat trips due to

overheating of the combustion chamber

(the thermostat electrical contact does not

close during operation)

• Makes sure the suction and feed grilles

are not blocked

• Make sure the environment is well

ventilated

• Make sure the warm air can exit freely

• Make sure the flow and pressure of the

gas are not too high

• Control unit trips due to irregular

operation of burner• Contact After-Sales Service

• Faulty gas pressure switch• Check the pressure switch and, if

necessary, replace

• Faulty micro-switch PAM• Check the micro-switch and, if

necessary, replace

• Faulty electronic control unit • Check the unit and, if necessary, replace

• Faulty thermostat • Check the thermostat and, if necessary,

replace

• Fan noise or vibrations

• Foreign bodies on fan blades• Remove foreign bodies

• Little air circulation • Eliminate and obstacles to proper air flow

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

10 Operating Instructions and Owner’s ManualENERCO GROUP, INC. |Indirect Fired Portable Heater

WIRING DIAGRAM

AP CONTROL BOX

FU FUSE

EL IONIZATION ELECTRODE

FUA FUSE

LI POVERHEAT THEMOSTAT

PA PRESSURE SWITCH 20 Pa

TA ROOM THERMOSTAT PLUG

IT TRANSFORMER H.T.

CO CAPACITOR

RV HEATING SWITCH

RE MOTOR RELAY

ST CONTROL LAMP

EV GAS TRAIN

MV COOLING MOTOR

RV1 VENTILATION MODE SWITCH

RE1 POST-VENTILATION RELAY

PL 10/07

05 06

19 21

72 73

62 63 64

HS4000NG/LP

25 26 27 26

32 34

45 37

05 47 46

26 31

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

PL 10/07

81 81

HS4000NG/LP

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

NO. HS# BM2 # DESCRIPTION NO. HS# BM2 # DESCRIPTION

01 50345 G06139-9005 Outlet cone 46 50470 C30376 Cable protection ø36mm

02 50346 M10203/1/B Screw TE M6x10 47 50260 E50750 Safety thermostat plastic profile

03 50347 G03114 Flame guard shield 48 50370 G03159-9010 Base

04 50348 G03147 Combustion chamber 49 50077 P50127 Control box cover

05 50349 E50745 Safety thermostat TY95H 50 50371 G00286

Electrical components drawer complete

06 50515 M20413 Clip holder sensing bulb 51 50372 P50132 Electrical components drawer

07 50351 G03150-9010 Upper body 52 50093 E20508 Fuse holder

08 50352 G03152-9010 Cover inspection 53 50092 E10313 Fuse (6x30) 20A

09 50353 G03154-9010 Lower body 54 50373 E11153 Relay finder 65.31.8.110AC

10 50411 C30372 Protection cable ø35 55 50374 E20319 Terminal board

11 50354 G03126 Combustion chamber deflectors 56 50375 E20305 Terminal board

12 50356 GA.0100206 Electrode ionisation probe 57 50329 E10931 Transformer H.T. BRAHMA

13 50545 I40332 Silicone pipe ø5x9 58 50330 E40229

Control box BRAHMA TGRD 81 120V

14 50507 I39106 Anti vibration joint 59 50097 E11125 Relay finder 65.31AC

15 50500 I20326 Connection 3/4"FF 60 50376 G06073 Plate for electrical components

16 50463 G06239-9010 Motor flange 61 50325 E20418 Stop button protection

17 50469 C30374 Drain plug 62 50337 E10110-1-P Switch 0-1

18 50454 E10704-110 Motor 450 W w/ capacitor 80µF 63 50570 E20640 Thermostat plug 3P+T

19 50455 E11249 Capacitor 80µF 64 50011 E20665 Drain plug

20 50166 T10261 Fan ø500 23° 65 50009 E30443

Electrical wire w/plug and cable fastener

21 50050 P30129 Inlet grill 66 50008 E11030 Lamp 120VAC

22 50357 G06330-9005 Valve support plate 70 50081 I20325 Connection 1/8"

23 50506 I39102 Seal 3/4" 71 50079 I31130 Connection straight ø6 1/8"

24 50505 I31205-1 Connection 3/4"MM 72 50511 M10323/1 Screw TCEI M4x20

25 50500 I20326 Connection 3/4"FF 73 50378 GA.0010208 Burner plate

26 50504 I31204 Connection 3/4"MM 74 50379 GA.0100204

Diffusion ring G20/G25-16 holes ø2.6

27 50358 T30330-2 Gas selector valve 75 50380 E20679 Terminal board

31 50359 T30333 Manual gas test firing valve 76 50381 G03129 Burner support

32 50360 E20943 Cable fastener PG9 77 50134 E10215 Ignition electrode

33 50361 E20932 Nut for PG9 78 50417 G02078 H.T. cable connect 90°

34 50334 T30111 Valve solenoid main 79 50382 G03168-9005 Lifting frame

35 50362 G06332-9005 Valve support 80 50383 G03169-9005 Lifting frame

36 50516 M20907 Valve support 81 50384 G03170-9005 Body support

37 50363 G03157-9010 Support for pressure plate 82 50385 G03171-9005 Wheel axle ø25

38 50364 E50443 Pressure switch 330Pa 83 40533 M20111 Washer ø26 x ø44 x 4mm

39 50365 I30414 Oil filter 84 50386 C10556 Wheel ø 260-ø 26mm

40 50337 E50441 Pressure switch 200Pa 85 40534 M20505 Wheel locking pin

41 50366 I40336 Silicone pipe ø4x1.5 86 50387 G03172-9005 Support

42 40501 I40501 Silicone pipe ø4x8 87 50388 G03173-9005 Rignt frame

43 50367 I20669 Connector straight T ø4 88 50389 G03174-9005 Left frame

44 50368 E20952 Cable fasterner PG11 89 50390 G03175-9005 Handle

45 50369 E20955 Nut for PG11 90 40505 C10203 Handle

HS4000DF NG/LP HD Heater Parts List BM2

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

OPERATING INSTRUCTIONS AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read

and follow all instructions. Place instructions in

a safe place for future reference. Do not allow

anyone who has not read these instructions to

assemble, light, adjust or operate the heater.

MODEL

4000IDG

HEATSTAR

BY ENERCO

ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001

Mr. Heater is a registered trademark of Enerco Group, Inc.

WARNING :

USE ONLY MANUFACTUR ER’S REPLACEMENT PARTS. US E OF ANY OTHER PARTS

COULD CAUSE INJURY OR DEATH. R EPLACEMENT PARTS AR E ONLY AVAI LABLE

DIRECT FROM THE FACTORY AND MUST B E INSTALLED BY A QUA LIFIED SERVICE

AGENCY.

PARTS O RDERING INFORMATI ON:

PURC HASING : Accessories may be purchased at any Mr. Heater/HeatStar local dealer

or direct from the factory

FOR INFORM ATI ON REGARDING SER VICE

Please call Toll-Free 800-251-0001 • www.enerco-mrheater.com

Our ofce hours are 8:30 AM – 5:00 PM, EST, Monday through Friday.

Email to: techservice@enerco-mrheater.com

Please include the model number, date of purchase, and description of problem in all

communication.

LIMITED WARRANT Y

The company warrants this product to be free from imperfections in material or workmanship,

under normal and proper use in accordance with instructions of The Company, for a period

of one year from the date of delivery to the buyer. The Company, at its option, will repair or

replace products returned by the buyer to the factory, transportation prepaid within said one

year period and found by the Company to have imperfections in material or workmanship.

If a part is damaged or missing, call our Technical Support Department at 800-251-0001.

Address any Warranty Claims to the Service Department, Enerco Group, Inc., 4560 W. 160TH

ST., Cleveland, Ohio 44135. Include your name, address and telephone number and include

details concerning the claim. Also, supply us with the purchase date and the name and address

of the dealer from whom you purchased our product.

The foregoing is the full extent of the responsibility of the Company. There are no other

warranties, express or implied. Specically there is no warranty of tness for a particular

purpose and there is no warranty of merchantability. In no event shall the Company be liable for

delay caused by imperfections, for consequential damages, or for any charges of the expense

of any nature incurred without its written consent. The cost of repair or replacement shall be

the exclusive remedy for any breach of warranty. There is no warranty against infringement of

the like and no implied warranty arising from course of dealing or usage of trade. This warranty

will not apply to any product which has been repaired or altered outside of the factory in any

respect which in our judgment aects its condition or operation.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you. This Warranty gives you specic legal

rights, and you may have other rights which vary from state to state.

Enerco Group, Inc. reserves the right to make changes at any time, without notice or obligation,

in colors, specications, accessories, materials and models.

ENERCO GROUP, INC. |Indirect Fired Portable Heater Operating Instructions and Owner’s Manual

ANSI Z83,7 CGA 2.14.

LISEZ SOIGNEUSEMENT LES INSTRUCTIONS :

Lisez et observez toutes les instructions. Conservez

les instructions pour vous y référer ultérieurement.

Interdisez à quiconque n’ayant pas lu les présentes

instructions d’assembler, d’allumer, de régler ou de

faire fonctionner cet appareil de chauage.

GUIDE D’UTILISATION ET INSTRUCTIONS DE FONCTIONNEMENT

HEATSTAR

BY ENERCO

HS4000DG

MODÈLE

ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 É.-U. • 800-251-0001

Mr. Heater et HeatStar sont des marques de commerce déposées de Enerco Group, Inc.

AVERTISSEMENT:

N’UTILISEZ QUE LES PIÈCES DE REMPLACEMENT DU FABRICANT. IL EST POSSIBLE

DE SE PROCURER CES PIÈCES DIRECTEMENT DE L’USINE OU PAR L’ ENTREMISE DES

DÉTAILLANTS LOCAUX MR. H EATER/HEATSTAR.

INFORMATIONS SUR LA COMMANDE DE PIÈCES :

ACHAT : On peut se procurer les accessoires par l’entremise de tous les détaillants

locaux Mr. Heater/HeatStar ou directement du fabricant

POUR OBTENIR DES INFORMATIONS SUR LE SERVICE

Appelez sans frais au 800-251-0001 • www.enerco-mrheater.com

Nos heures d’ouverture sont de 8 h 30 à 17 h HNE, du lundi au vendredi.

Adressez vos courriels à : techservice@mrheater.com

Veuillez indiquer le numéro du modèle, la date d’achat et la description du problème

dans toutes vos communications avec nous.

GARANTIE LIMITÉE

L’entreprise garantit ce produit contre tout défaut de matériel ou de main-d’œuvre, dans des

conditions d’utilisation normale et adéquate, conformément aux instructions de l’entreprise,

pour une période d’un an à compter de la date de livraison à l’acheteur. L’entreprise réparera ou

remplacera, à sa discrétion, les produits retournés port payé par l’acheteur au fabricant dans la

période d’un an et jugés par l’entreprise comme présentant des défauts de matériel ou de main-

d’œuvre.

Si une pièce est endommagée ou manquante, téléphonez à notre service de soutien technique

au 800-251-0001.

Adressez toute réclamation relative à la garantie à Service Department, Enerco Group, Inc., 4560

W. 160TH ST., Cleveland, Ohio 44135 États-Unis. Indiquez vos nom, adresse et numéro de téléphone

ainsi que les détails de la réclamation. Indiquez-nous également la date d’achat et le nom et l’adresse

du détaillant de qui vous avez acheté le produit.

Ce qui est énoncé ci-dessus constitue la responsabilité totale de l’entreprise. Il n’existe aucune autre

garantie, expresse ou tacite. Plus précisément, il n’y a aucune garantie concernant l’adéquation à une

utilisation particulière ni aucune garantie concernant la qualité marchande. En aucun cas l’entreprise

ne sera tenue responsable des retards causés par des défectuosités, ni des dommages indirects,

ni des dépenses encourues sans son consentement écrit, quelle que soit leur nature. Le coût de la

réparation ou du remplacement sera le seul recours possible en cas de violation de garantie. Il n’y

a aucune garantie contre une transgression de ce genre ni aucune garantie tacite découlant des

usages du commerce ou de la façon habituelle d’échanger. La présente garantie ne s’applique à

aucun produit qui a été réparé ou modié par d’autres que le fabricant si cela inue de quelque

façon que ce soit sur l’état de l’appareil ou son fonctionnement, selon notre jugement.

Certains États ou provinces ne permettent pas d’exclure ou de limiter les dommages indirects ou

subséquents. Par conséquent, les limitations ou exclusions ci-dessus mentionnées ne vous concernent

peut-être pas. La présente garantie vous accorde des droits juridiques précis, mais vous pourriez

avoir d’autres droits qui varient selon la province ou l’État.

Enerco Group Inc. se réserve le droit d’eectuer des modications en tout temps, sans préavis ni

08/08 #50120ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001

13 Le fait de Faire marcher des Instructions et le Manuel de PropriétaireENERCO GROUP, INC. |Chauage portatif indirect-tiré