Simplicity 040612-00 Manuel utilisateur

Page | i

Operation Instructions

GC1030 SERIES GENSET Controller

Not for reproduction

Page | ii

Safety Definitions

For your safety, the safety of others, and to protect the performance of equipment, obey the

warnings in the manual before operation, during operation, and during maintenance procedures.

indicates a potential personal injury hazard.

DANGER

indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

indicates a situation which can cause damage to the equipment, personal property and/or the

environment, or cause the equipment to operate incorrectly.

WARNING

Failure to read, understand and obey the instructions in this manual could result in death or se-

rious injury. Read, understand and obey the instructions in this manual before operating this

product.

Not for reproduction

Page | iii

List of Abbreviations and Acronyms

This list contains the abbreviations and acronyms used in this document. Refer to this list for

their respective description.

Acronym

Description

AC

Alternating Current

ACK

Acknowledge

ALT

Alternator

AMF

Auto Mains Failure

AUX

Auxiliary

AVR

Automatic Voltage Regulator

CHG

Charging

CKT

Circuit

CT

Current Transformer

DC

Direct Current

DIG IN

Digital Input

EGov

Electronic Governor

ENG TEMP

Engine Temperature

GCU

Genset Control Unit

Genset

Generator Set

GND

Ground

GST

Gain Schedule Trigger

HMI

Human Machine Interface

HSD

High Side Driver

HWT

High Water Temperature

ID

Identifier

LCD

Liquid Crystal Display

LED

Light Emitting Diode

LIM

Low Idle Mode

LLOP

Low Lube Oil Pressure

LOP

Lube Oil Pressure

LVL

Level

MCP

Manual Control Panel

MPU

Magnetic Pickup Unit

OV

Over Voltage

PF

Power Factor

PID

Proportional Integral Derivative

PWM

Pulse Width Modulation

RMS

Root Mean Square

RPM

Revolutions Per Minute

RTC

Real Time Clock

R-Y-B

Red-Yellow-Blue

SCP

Sensor Common Point

SMD

State Machine Diagram

TEMP

Temperature

USB

Universal Serial Bus

UV

Under Voltage

PF

Power Factor

AVR

Automatic Voltage Regulator

Not for reproduction

Page | iv

Table of Contents

Key Highlights of the Product ................................................................................................... 1

Installation ............................................................................................................................ 1 1

Terminal Description ..................................................................................................... 1 1.1

Description of Control Keys ............................................................................................... 4 2

Functions of Control Keys ........................................................................................... 4 2.1

Configuration of GCU .......................................................................................................... 5 3

List of Parameters ......................................................................................................... 5 3.1

Operating Modes ............................................................................................................... 14

4

Auto Mode.................................................................................................................... 14 4.1

Auto Mains Failure (AMF) ....................................................................................... 14 4.1.1

Remote Start/Stop (2 Wire) .................................................................................... 16 4.1.2

Auto Exercise Mode ............................................................................................... 16 4.1.3

Manual Mode ............................................................................................................... 17 4.2

Low Idle Mode (LIM) ............................................................................................... 18 4.2.1

Alarms ................................................................................................................................ 19 5

Troubleshooting ................................................................................................................. 21 6

Notes ......................................................................................................................................... 24

Not for reproduction

Page | v

List of Figures

Figure 1: GC1030 Series Genset controller from the backside .................................................... 1

Figure 2: Control key function ...................................................................................................... 4

Figure 3: Configuration mode screen ........................................................................................... 5

Figure 4: Configuration mode authentication page screen ........................................................... 5

Figure 5: Saving settings screen .................................................................................................. 5

Figure 6: SMD for AMF mode ..................................................................................................... 15

Figure 7: SMD for auto exercise mode ....................................................................................... 17

Figure 8: SMD for manual mode ................................................................................................ 18

Not for reproduction

Page | vi

List of Tables

Table 1: Voltage input terminology ............................................................................................... 2

Table 2: Details of the GC1030 Series terminals .......................................................................... 2

Table 3: Control keys in different modes ...................................................................................... 4

Table 4: Parameters ..................................................................................................................... 5

Table 5: Alarm actions ................................................................................................................ 19

Table 6: Alarms and their causes ............................................................................................... 19

Table 7: Common faults and their remedial actions .................................................................... 21

Not for reproduction

Page | 1

Key Highlights of the Product

 Auto, Manual and Remote Start /Stop Modes for 1-phase & 3-phase gensets

 Electronic governor controller integration

 RPM sensing using frequency and MPU

 Supports Auto Exercise Modes

 Real time clock-based event logs

 PC connectivity via USB port, RS485, CAN J1939 protocol

 Backlit and full graphics display with power saving feature

Installation 1

Terminal Description 1.1

The figure that follows shows the rear view of the controller.

Figure 1: GC1030 Series Genset controller from the backside

Not for reproduction

Page | 2

Table 1: Voltage input terminology

Sr. No.

System

Terminology 1

Terminology 2

1

1 Phase 2 wire

R-N

L1-N

2

1 Phase 3 wire

R-Y-N

L1-L2-N

3

3 Phase 4 wire

R-Y-B-N

L1-L2-L3-N

Table 2: Details of the GC1030 Series terminals

Sr.

No.

Name

Description

1

BATT -

Battery negative

2

BATT +

Battery positive

3

OUT A

High side driver output – A

4

OUT B

High side driver output – B

5

OUT C

High side driver output – C

6

OUT D

High side driver output – D

7

D+ CHG ALT

Reserved

8

OUT E

High side driver output – E

9

OUT F

High side driver output – F

10

DIG_IN A

Input from switch – A

11

DIG_IN B

Input from switch – B

12

DIG_IN C

Input from switch – C

13

CAN H

CAN high

14

CAN L

CAN low

15

RS485_B

RS485 – B

16

RS485_A

RS485 – A

17

GOV_ACT – OUT1

Output for the Actuator – 1

18

GOV_ACT – OUT4

Output for the Actuator – 4

19

GOV_ACT – OUT2

Output for the Actuator – 2

20

GOV_ACT – OUT3

Output for the Actuator – 3

21

DIG_IN D

Input from switch – D

22

DIG_IN E

Input from switch – E

23

ANLG_V IN

Analog input 4-20mA for LOP or 2.5 ± 2V

24

ANLG_IN ENG_TEMP

Analog input from Engine Temperature

Sensor

25

ANLG_IN Fuel Level

Analog input from Fuel Level Sensor

26

ANLG_IN LOP

Analog input from Lube Oil Pressure

Sensor

27

GEN_V IN NTRL

Voltage input from Gen Neutral

28

GEN_V IN B

Voltage input from Gen B / L3

29

GEN_V IN Y

Voltage input from Gen Y / L2

30

GEN_V IN R

Voltage input from Gen R / L1

31

MAINS_V IN NTRL

Voltage input from Mains Neutral

32

MAINS_V IN B

Voltage input from Mains Phase B / L3

33

MAINS_V IN Y

Voltage input from Mains Phase Y / L2

34

MAINS_V IN R

Voltage input from Mains Phase R / L1

Not for reproduction

Page | 3

Sr.

No.

Name

Description

35

CT – IN B1

CT input 1 from Phase B / L3

36

CT – IN B2

CT input 2 from Phase B / L3

37

CT – IN Y1

CT input 1 from Phase Y / L2

38

CT – IN Y2

CT input 2 from Phase Y / L2

39

CT – IN R1

CT input 1 from Phase R / L1

40

CT – IN R2

CT input 2 from Phase R / L1

41

SENSOR COMM

Sensor common point

42

MPU I/P (Speed

Sensor)

Input from engine speed sensor (Inductive)

Not for reproduction

Page | 4

Description of Control Keys 2

Figure 2: Control key function

1. Menu Navigation Up key

2. Menu Navigation Down key

3. Stop/Config key

4. Start/Select key

5. Auto/Manual Mode selection key

Functions of Control Keys 2.1

The table that follows gives a brief overview of different functions of control keys in different modes.

Table 3: Control keys in different modes

#

Mode

Key input

Function

1

Manual

Start

Starts the engine in LIM

Start+Start

Exits LIM and operates at normal speed

2

Manual

Auto

Enters Auto Mode

Stop

Stops the engine when engine is running

Stop (long pressed)

Enters Configuration Mode

Stop + Down (long pressed)

Enters Programming Mode

3

Auto

Stop

Stops the engine and enters Manual Mode

4

Manual/Auto/

Configuration

Up/Down

Scrolls the screens/parameter

5

Manual/Auto

Up + Down

Acknowledges and clears the alarm

6

Configuration

Start

Selects/saves the parameter

7

Up + Down (long pressed)

Enters on event log page

8

Stop (long pressed)

Back to Manual Mode

9

Event log

Up + Down (long pressed)

Back to Configuration Mode

10

Programming

Up + Down (long pressed)

Controller enters in Application Mode

1

3

2

4

5

Not for reproduction

Page | 5

Configuration of GCU 3

To configure the controller, please do the instructions that follow:

 To enter the configuration mode, push and hold the “STOP” key for at least 3 seconds. The

following screen will appear on the GCU:

Figure 3: Configuration mode screen

 If you want to only view the configuration, push the “STOP” key on the GCU. If you wish to

change the configuration, push the “START” key on the GCU.

Figure 4: Configuration mode authentication page screen

 The GCU will ask for a password (0000). Enter the password by using the up & down arrow key

for changing the digit and the “START” key for selecting the digit. The 4 digits will start blinking

individually as each one is selected. Press the “START” button as mentioned earlier to enter the

correct digit.

 After completion of the parameter configuration, push and hold the “STOP” key to exit from

configuration mode. Before exiting from the configuration mode the controller will show the

following screen:

Figure 5: Saving settings screen

List of Parameters 3.1

The table that follows gives a brief overview of configurable parameters in GC1030 Series controller.

Table 4: Parameters

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

Module

(MODULE)

General

(GENERAL)

* Power On Mode

(POWER ON MODE)

Manual/Auto

* Power On Lamp Test

(POWER ON LAMP TEST)

Disable/Enable

Load Histogram

(LOAD HISTOGRAM)

Disable/Enable

Auto-Clear Warning Alarm

(WARNING AUTO CLEAR)

Disable/Enable

Language

(LANGUAGE)

English

Not for reproduction

Page | 6

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

Display

(DISPLAY)

Contrast

(CONTRAST)

0 – 100 %

Power Save Mode

(POWER SAVE MODE)

Disable/Enable

Communication

(COMMUNICATION)

Communication Mode

(COMM MODE)

None/MODBUS

* Slave ID

(MODBUS SLAVE ID)

1 – 247

* Baudrate

(MODBUS BAUDRATE)

1200/2400/4800/9600/19200/

38400/57600/115200 bps

* Parity Bit

(PARITY BIT)

None/Even/Odd

Auto Exercise

(AUTO EXERCISE)

Exercise Option

(EXER OPTN)

No Exercise/Standard

Exercise

Cycle

(EXER CYCLR)

No run/0.1/5/10/15/20 min run

Event Occurence

(EXER EVENT OCCR)

Weekly/Monthly

Event Day

(EXER EVENT DAY)

Weekdays/1 – 28 days

Start Time

(EXER START TIME)

00:00 – 23:59 hour

Exercise Skip Enable

(EXER SKIP ENABLE)

Yes/No

45 min Burn Off

(45 MIN BURN OFF)

45 min Burn Off

(45 MIN BURN OFF)

Disable/Enable

Event Month

(EVENT MONTH 1)

March/April/May/None

Event Day

(EVENT DAY 1)

1 - 28

Start Time

(EVENT START TIME 1)

00:00 – 23:59 hour

Event Month

(EVENT MONTH 2)

August/September/

October/None

Event Day

(EVENT DAY 2)

1 - 28

Start Time

(EVENT START TIME 2)

00:00 – 23:59 hour

Digital Inputs

(INPUTS)

Digital Input X

(DIG IN X)

X= A/B/C/D/E

* Source

(SOURCE)

* Polarity

(POLARITY)

Close to Activate/Open to

Activate

* Action

(ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Activation

(ACTIVATION)

Never/From Engine Start/

From Monitoring On/Always

* Activation Delay

* (ACTIVATION DELAY)

1 – 60 sec

Analog Inputs

Analog Input 1

* Use Input As

Not used/Digital Input G/Anlg

Not for reproduction

Page | 7

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

(AMB TEMP/DIG G)

(USE INPUT AS)

In Amb Temp

* Circuit Fault Action

(CKT FAULT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Ambient Temperature Sensor

Calibration Table

Analog Input 2

(FUEL LVL/DIG H)

* Use Input As

(USE INPUT AS)

Not used/Digital Input H/Anlg

In Fuel LVL

* (Digital) Source

((DIG) SOURCE)

* (Digital) Polarity

((DIG) POLARITY)

Close to Activate/Open to

Activate

* (Digital) Action

((DIG) ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* (Digital) Activation

((DIG) ACTIVATION)

Never/From Engine Start/

From Monitoring On/Always

* (Digital) Activation Delay

((DIG) ACTIVATION DELAY)

1 – 60 sec

* Low Fuel Level Shutdown

(SHUTDOWN)

Disable/Enable

* Low Fuel Level Shutdown

Threshold

(SHUTDOWN THRESHOLD)

0 – 78 %

* Low Fuel Level Notification

(NOTIFICATION)

Disable/Enable

* Low Fuel Level Notification

Threshold

(NOTIFICATION THRESH)

2 – 80 %

* Fuel Tank Capacity

(FUEL TANK CAPACITY)

2 – 1000 litre

* Fuel Theft Warning

(FUEL THEFT ALARM)

Disable/Enable

* Fuel Theft Alarm Threshold

(FUEL THEFT THRESHOLD)

1 – 100 % per hour

* Circuit Fault Action

(CKT FAULT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Fuel Sensor Reference

(FUEL SENSOR REFERENCE)

Engine Body/Battery Negative

* Fuel Level Sensor Calibration

Table

Analog Input 3

(LOP RES/ DIG F)

* Use Input As

(SENSOR SELECTION)

Not used/Digital Input F/Anlg

In LOP

* (Digital) Source

((DIG) SOURCE)

* (Digital) Polarity

((DIG) POLARITY)

Close to Activate/Open to

Activate

* (Digital) Action

((DIG) ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* (Digital) Activation

((DIG) ACTIVATION)

Never/From Engine Start/

From Monitoring On/ Always

* (Digital) Activation Delay

1 – 60 sec

Not for reproduction

Page | 8

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

((DIG) ACTIVATION DELAY)

* Low Level Shutdown

(SHUTDOWN)

Disable/Enable

* Low Level Shutdown Threshold

(SHUTDOWN THRESHOLD)

0.0 – 9.8 bar

* Low Level Warning

(WARNING)

Disable/Enable

* Low Level Warning Threshold

(WARNING THRESHOLD)

0.2 – 10.0 bar

* Circuit Fault Action

(CKT FAULT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Lube Oil Pressure Sensor

Calibration Table

Analog Input 4

(LOP CURR/ DIG I)

* Use Input As

(SENSOR SELECTION)

Not used/Digital Input I/Anlg

In LOP(4 – 20mA)

* (Digital) Source

((DIG) SOURCE)

* (Digital) Polarity

((DIG) POLARITY)

Close to Activate/Open to

Activate

* (Digital) Action

((DIG) ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* (Digital) Activation

((DIG) ACTIVATION)

Never/From Engine Start/

From Monitoring On/ Always

* (Digital) Activation Delay

((DIG) ACTIVATION DELAY)

1 – 60 sec

* Shutdown

(SHUTDOWN)

Disable/Enable

* Shutdown Threshold

(SHUTDOWN THRESHOLD)

0.0 – 9.8 (0.0 – 9.8 Bar)

* Warning

(WARNING)

Disable/Enable

* Warning Threshold

(WARNING THRESHOLD)

0.2 – 10.0 (0.2 – 10.0 Bar)

* Circuit Fault Action

(CKT FAULT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Lube Oil Pressure Sensor

Calibration Table

Outputs

(OUTPUTS)

Output X

(OUT X)

X= A/B/C/D/E/F

* Source

(SOURCE)

* On Activation

(ON ACTIVATION)

Energize/De-energize

Timers

(TIMERS)

Cranking

(CRANKING

TIMER)

* Crank Hold Time

(CRANK HOLD TIME)

3 – 15 sec

* Crank Rest Time

(CRANK REST TIME)

2 – 60 sec

* Manual Start Delay

(MANUAL START DELAY)

0 – 30 sec

* Auto Start Delay

(AUTO START DELAY)

0 – 43200 sec

General Timer

* Safety Monitoring Delay

10 – 60 sec

Not for reproduction

Page | 9

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

(GENERAL TIMER)

(SAFETY MONITOR DELAY)

Mains Detect Delay

(MAINS DETECT DELAY)

1 – 300 sec

* Alternator Detect Delay

(ALT DETECT DELAY)

1 – 60 sec

Warm-Up Delay

(WARM UP DELAY)

0 – 60 sec

Return To Mains Delay

(RETN-TO-MAINS DELAY)

0 – 600 sec

* Engine Cooling Time

(ENG COOL TIME)

0 – 300 sec

* Stop Action Time

(STOP ACTION TIME)

10 – 120 sec

* Additional Stopping Time

(ADDN STOPPING TIME)

0 – 120 sec

Load Transfer Delay

(LOAD TRANSFER DELAY)

0 – 60 sec

Power Save Mode Delay

(PWR SAVE MODE DELAY)

5 – 1800 sec

Sounder Alarm Time

(SOUNDER ALARM TIMER)

1 – 300 sec

Auto Exit Config Mode

(AUTO EXIT CNFG TMR)

10 – 1800 sec

Generator

(GENERATOR)

Alternator

Configuration

(ALT CONFIG)

* Alternator Present

(ALT PRESENT)

No/Yes

* Number Of Poles

(NUMBER OF POLES)

2/4/6/8

* AC system

(ALT AC SYSTEM)

Single Phase 2 Wire/ Single

Phase 3 Wire/ Three Phase 4

Wire (1Ph 2 wire/1Ph 3

wire/3Ph 4 wire)

* Min Healthy Voltage

(MIN HEALTHY VOLT)

50 – 350 Volt Ph-N

* Min Healthy Frequency

(MIN HEALTHY FREQ)

10 – 75 Hz

* Phase Reversal Detection

(PHASE REVERSE DETECT)

Disable/Enable

* Phase Reversal Action

(PHASE REVERSE ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Auto Load Transfer

(AUTO LOAD TRANSFER)

Disable/Enable

* Genset Nominal Voltage

(NOMINAL VOLTAGE (L-L))

100 – 650 Volt L-L

* Genset Nominal Frequency

(NOMINAL FREQUENCY)

10.0 – 75.0 Hz

Voltage Monitoring

(VOLT MONITOR)

* Under-voltage Shutdown

(UNDER VOLT SHUTDOWN)

Disable/Enable

* Under-voltage Shutdown

Threshold

(UV SHUTDWN THRESHLD)

50 – 295 Volt Ph-N

Not for reproduction

Page | 10

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

* Under-voltage Warning

(UNDER VOLT WARNING)

Disable/Enable

* Under-voltage Warning

Threshold

(UV WARNING THRESHOLD)

55 – 300 Volt Ph-N

* Over-voltage Shutdown

(OVER VOLT SHUTDOWN)

Disable/Enable

* Over-voltage Shutdown

Threshold

(OV SHUTDWN THRESHLD)

105 – 350 Volt Ph-N

* Over-voltage Warning

(OVER VOLT WARNING)

Disable/Enable

* Over-voltage Warning

Threshold

(OV WARNING THERSHOLD)

100 – 345 Volt Ph-N

Frequency

Monitoring

(FREQ MONITOR)

* Under-frequency Shutdown

(UNDER FREQ SHUTDOWN)

Disable/Enable

* Under-frequency Shutdown

Threshold

(UF SHUTDWN THRESHLD)

10.0 – 59.0 Hz

* Under-frequency Warning

(UNDER FREQ WARNING)

Disable/Enable

* Under-frequency Warning

Threshold

(UF WARNING THRESHOLD)

11.0 – 60.0 Hz

* Over-frequency Shutdown

(OVER FREQ SHUTDOWN)

Disable/Enable

* Over-frequency Shutdown

Threshold

(OF SHUTDWN THRESHLD)

26.0 – 75.0 Hz

* Over-frequency Warning

(OVER FREQ WARNING)

Disable/Enable

* Over-frequency Warning

Threshold

(OF WARNING THRESHOLD)

25.0 – 74.0 Hz

Current Monitoring

(CURRENT

MONITOR)

* CT Ratio

(CT RATIO)

0 – 8000 / 5

* Over-current Action

(OVER CURR ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Over-current Threshold

(OVER CURR THRESHOLD)

5 – 10000 Amp

* Over-current Delay

(OVER CURR DELAY)

1 – 600 sec

* CT Location

(CT LOCATION)

On Load Cable/On Alt Output

Cable

Load Monitoring

(LOAD MONITOR)

* Generator Rating

(GEN RATING)

0 – 8000 kW

* Over-load Action

(OVERLOAD ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Over-load Threshold

(OVERLOAD THRESHOLD)

50 – 150 %

Not for reproduction

Page | 11

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

* Over-load Monitoring Delay

(OVERLOAD MON DELAY)

1 – 600 sec

* Unbalanced Load Action

(UNBAL LOAD ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Unbalanced Load Threshold

(UNBAL LOAD THRESHOLD)

5 – 200 %

* Unbalanced Load Delay

(UNBAL LOAD DELAY)

1 – 600 sec

* Extended Over-load Trip

(EXT OL TRIP)

Disable/Enable

* Extended Over-load Trip

Threshold

(EXT OL THRESHOLD)

50 – 150 %

Mains

(MAINS)

Configuration

(MAINS CONFIG)

Mains Monitoring

(MAINS MONITORING)

Disable/Enable

* Mains AC system

(MAINS AC SYSTEM)

Single Phase 2 Wire/Single

Phase 3 Wire/Three Phase 4

Wire (1Ph 2 wire/1Ph 3 wire

/3Ph 4 wire)

* Phase Reversal Detection

(PHASE REVERSE DETECT)

Disable/Enable

* Phase Reversal Action

(PHASE REVERSE ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

Under-voltage

Monitoring

(UNDER VOLT

MON)

* Under-voltage

(ENABLE)

Disable/Enable

* Trip

(TRIP)

50 – 298 Volt Ph-N

* Return

(RETURN)

52 – 300 Volt Ph-N

Over-voltage

Monitoring

(OVER VOLT MON)

* Over-voltage

(ENABLE)

Disable/Enable

* Trip

(TRIP)

102 – 350 Volt Ph-N

* Return

(RETURN)

100 – 348 Volt Ph-N

Under-frequency

Monitoring

(UNDER FREQ

MON)

* Under-frequency

(ENABLE)

Disable/Enable

* Trip

(TRIP)

10.0 – 59.0 Hz

* Return

(RETURN)

11.0 – 60.0 Hz

Over-frequency

Monitoring

(OVER FREQ MON)

* Over-frequency

(ENABLE)

Disable/Enable

* Trip

(TRIP)

26.0 – 75.0 Hz

* Return

(RETURN)

25.0 – 74.0 Hz

Engine

(ENGINE)

Crank Disconnect

(CRANK DISCON)

* Start Attempts

(START ATTEMPTS)

1 – 9

* Disconnect On Oil Pressure

Disable/Enable

Not for reproduction

Page | 12

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

Sensor

(DISCONN ON LOP SENS)

* Pressure Sensor Monitoring

Threshold

(DISCONN LOP THRESH)

0.5 – 10.0 bar

* Monitor Pressure Switch Before

Crank

(MON LLOP BEFR CRANK)

Disable/Enable

* Monitor Pressure Sensor Before

Crank

(MON LOP BEFR CRANK)

Disable/Enable

* Disconnect On Oil Pressure

Switch

(DISCONN ON LLOP SW)

Disable/Enable

* Pressure Switch Transient Time

(LLOP SW TRANS TIME)

0.0 – 3.0 sec

* Crank Disconnect At Alt

Frequency

(DISCONN AT ALT FREQ)

10 – 70 Hz

* Crank Disconnect At Engine

Speed

(DISCONN AT ENG SPEED)

150 – 4000 rpm

Speed Monitoring

(SPEED MONITOR)

* Engine Speed Sense Source

(SPEED SENSE SOURCE)

Sensor input only/

Alternator output only/

Primary Sensor/Secondary

Alternator/

Primary Alternator/Secondary

Sensor

* Flywheel Teeth

(FLYWHEEL TEETH)

1 – 300

* Under-speed Shutdown

(UNDER SPEED SHUTDOWN)

Disable/Enable

* Under-speed Threshold

(UNDER SPD THRESHOLD)

0 – 3600 rpm

* Under-speed Delay

(UNDER SPD DELAY)

1 – 60 sec

* Over-speed Threshold

(OVER SPD THRESHOLD)

700 – 4500 rpm

* Over-speed Delay

(OVER SPEED DELAY)

0.1 – 20 sec

* Gross Over-speed Threshold

(GROSS OS THRESHOLD)

100 – 200 %

Battery Monitoring

(BATTERY

MONITOR)

* Low Battery Voltage Action

(LOW VOLT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

* Low Battery Voltage Threshold

(LOW VOLT THRESHOLD)

8.0 – 31.0 volt

* Low Battery Voltage Delay

(LOW VOLT DELAY)

5 – 1800 sec

* High Battery Voltage Action

(HIGH VOLT ACTION)

None/Notification/Warning/

Electrical Trip/Shutdown

Not for reproduction

Page | 13

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

* High Battery Voltage Threshold

(HIGH VOLT THRESHOLD)

9.0 – 32.0 volt

* High Battery Voltage Delay

(HIGH VOLT DELAY)

5 – 1800 sec

Maintenance

(MAINTENANCE)

Maintenance Alarm

(MAINT ALARM)

Alarm Action

(ACTION)

Notification/Warning

Due At Engine Hours

(DUE AT ENGINE HOURS)

10 – 65000 Hrs

Alarm Due Date

(ALARM DUE

DATE)

Alarm Due Date

DD/MM/YYYY

Rotary Actuator

(ROTARY

ACTUATOR)

General

(GENERAL)

* Actuator Application

(ACTUATOR APPLN)

As E-Governor/As Start / Stop

Device

* Actuator Speed

(ACTUATOR SPEED)

1 – 10 x 25 Hz

* Actuator Direction

(ACTUATOR DIRECTION)

(Clockwise/Anti–Clockwise) to

Stop

Engine Start

Strategy

(ENG START

STRGY)

* Cranking Steps

(CRANKING STEPS)

5 – 5000

* Initial Low Speed Delay

(INIT LOW SPEED DELAY)

0 – 180 sec

* Initial Low Speed

(INIT LOW SPEED)

500 – 1800 RPM

* PID Trigger Speed

(PID TRIGGER SPEED)

20 – 2800 RPM

* Ramp Up Time

(RAMP UP TIME)

1 – 180 sec

* PID on Time

(PID ON TIME)

1 – 180 sec

* LIM P Gain

(LIM P GAIN)

0 – 1000

* LIM I Gain

(LIM I GAIN)

0 – 2000

* LIM D Gain

(LIM D GAIN)

0 – 1000

* Cold Sweep Enable

(COLD SWEEP ENABLE)

Yes/No

* Cold Sweep Angle

(COLD SWEEP ANGLE)

0 – 180 Deg

Generator EGov

Configuration

(GEN EGOV CNFG)

* Set Speed Selection

(SET SPEED SELECTION)

Fixed Speed(0% Droop)/

Speed Bias Input (0-5 V)/

Load Based Droop

* Droop

(DROOP)

0 – 4 %

* Target Speed

(TARGET SPEED)

500 – 4000 RPM

* Proportional Gain (Kp)

(PROPORTIONAL GAIN)

0 – 1000

* Integral Gain (Ki)

0 – 2000

Not for reproduction

Page | 14

Level 0

Level 1 (On screen)

Level 2 (On screen)

Parameters (On screen)

(INTEGRAL GAIN)

* Derivative Gain (Kd)

(DERIVATIVE GAIN)

0 – 1000

* Friction Setoff

(FRICTION SETOFF)

0 – 1000

* Gain Schedule Trigger

(GAIN SCHEDULE TRIGGER)

0.0 – 100.0 %

* Loading Factor

(LOADING FACTOR)

0 – 1000

* Unloading Factor

(UNLOADING FACTOR)

0 – 1000

Start/Stop

Configuration

(STR/STP DEV

CNFG)

* Running Steps

(RUNNING STEPS)

0 – 500

(MISC SETTINGS)

PASSWORD 1

* ####

0 – 9 for each digit

PASSWORD 2

####

0 – 9 for each digit

PASSWORD 3

####

0 – 9 for each digit

(RESET

COUNTERS)

(GENSET)

* (RUN TIME)

(In hours)

(NO. OF STARTS)

(In numbers)

(NO. OF TRIPS)

(In numbers)

(SELECT PROFILE)

(Profile Name)

A – Z, 0 – 9

(DATE AND TIME)

(DATE)

(DD / MM / YYYY)

0 – 9 for each digit

(TIME)

(Hours)

(In hours)

(ACTUATOR TEST)

(ENABLE)

Yes/No

(TEST DURATION)

0 – 10 sec

* Note: Certain parameters can only be changed by the dealer while others can only be changed by the

manufacturer (designated by an *). Some default parameters are subject to change during firmware updates

per the manufacturer. The dealer password is available on the Briggs and Stratton

®

Power Portal.

Operating Modes 4

There are two modes of operation:

 Auto Mode

 Manual Mode

Auto Mode 4.1

To enter Auto Mode, push the “AUTO” key. While in Auto Mode, the generator will start and run under

any one of these conditions:

 Auto Mains Failure (AMF)

 Remote Start/Stop (2 Wire)

 Auto Exercise

Auto Mains Failure (AMF) 4.1.1

When the Mains Monitoring is enabled (default setting) in the Mains configuration and the controller is

in the Auto Mode, AMF mode gets activated.

In this mode, if the Mains is healthy, the genset remains in the OFF condition. When the Mains voltage

drops below a certain threshold, the controller gives a start command. Once the genset is started and

its loading parameters reach the threshold values, the genset contactor is latched and the load is

Not for reproduction

La page charge ...

Simplicity 040612-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 040612-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents