Parkside 275679 Instructions Manual

IAN 275679

RANDOM ORBITAL AIR SANDER PDEXS 150 B2

RANDOM ORBITAL AIR SANDER

Translation of the original instructions

TRYKLUFT-EXCENTERSLIBER

Oversættelse af den originale driftsvejledning

DRUCKLUFT-EXZENTERSCHLEIFER

Originalbetriebsanleitung

PONCEUSE ORBITALE SPÉCIALE À AIR

Traduction des instructions d’origine

EXCENTRIEKSLIJPMACHINE OP

PERSLUCHT

Vertaling van de originele gebruiksaanwijzing

GB / IE Translation of the original instructions Page 1

DK Oversættelse af den originale driftsvejledning Side 13

FR / BE Traduction des instructions d’origine Page 25

NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 39

DE / AT / CH Originalbetriebsanleitung Seite 51

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

Avant de lire le mode d'emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l'appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

1

PDEXS 150 B2

GB

IE

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General safety instructions for compressed air tools ....................3

Hazards caused by ﬂying parts ................................................. 3

Hazards caused by entanglement ............................................... 4

Hazards during operation ..................................................... 4

Risks due to repetitive movements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Hazards caused by accessories ................................................. 4

Hazards in the workplace ..................................................... 5

Risks due to dust and vapours .................................................. 5

Risks due to noise ............................................................ 5

Risks due to vibrations ........................................................ 6

Additional safety instructions for pneumatic machines ................................ 6

Appliance-speciﬁc safety instructions for sanders .................................... 6

Before use .......................................................7

Fitting the connector nipple .................................................... 7

Fitting the sanding disc ........................................................ 7

Selecting a sandpaper disc .................................................... 7

Fitting the sandpaper disc ..................................................... 8

Lubrication ................................................................. 8

Reﬁlling oil ................................................................. 8

Connecting to a compressed air source ........................................... 8

Operation .......................................................9

Switching on and oﬀ ......................................................... 9

Regulation of vibration output .................................................. 9

Sanding ................................................................... 9

Working procedures .......................................................... 9

Maintenance and cleaning .........................................10

Troubleshooting .................................................10

Disposal ........................................................11

Warranty .......................................................11

Service .........................................................11

Importer .......................................................11

Translation of the original Conformity Declaration .....................12

2

PDEXS 150 B2

GB

IE

RANDOM ORBITAL AIR SANDER

PDEXS 150 B2

Introduction

Congratulations on the purchase of your new ap-

pliance. You have selected a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the speciﬁed areas of application. Please also

pass on these operating instructions to any future

owner.

Intended use

This compressed air-powered random orbital sander

is suitable for sanding, polishing and for the prepa-

ration of various surfaces. Any other usage of or

modiﬁcation to the appliance is deemed to be

improper and carries a signiﬁcant risk of accidents.

The manufacturer accepts no responsibility for

damage(s) resulting from improper usage. This

appliance in intended only for domestic use.

Symbols on the compressed air tool

WARNING!

Read the instruction

manual before use.

Wearing of protec-

tive gloves and safety

clothing is recom-

mended.

Always wear eye

protection when using

or maintaining the

sander.

Always wear respira-

tory protection in the

presence of dust.

Always wear hearing

protection.

Oil daily

Rotation direction

Features

Housing

Blocking device

Trigger

Handle

Connector nipple

Speed controller

Spindle lock

Eccentric spindle with sanding disc socket

Sanding disc

Protective cuﬀ

Sandpaper disc

Oil container

Teﬂon tape

Package contents

1 random orbital air sander

1m Teﬂon tape

1 oil container

1 connector nipple 6.35 mm (1/4")

1 sanding disc Ø 150 mm (with Velcro)

5 sanding sheets (P60/P80/P100/P120/P150)

1 operating manual

Technical data

Rated speed: max. 10000 rpm

Rated air pressure: max. 6.3 bar

Sanding disc: Ø 150 mm

Weight (without accessories) approx. 1.65 kg

3

PDEXS 150 B2

GB

IE

Noise emission values:

Noise measurement determined in accordance

with ISO 15744.

Sound pressure level: L

pA

= 90.4 dB (A)

Uncertainty: K

pA

= 3 dB

Sound power level: L

WA

= 101.4 dB (A)

Uncertainty: K

WA

= 3 dB

Wear ear protection!

Vibration emission value:

Vibration emission value determined in accordance

with ISO 28927-3 and EN 12096:

a

h

= 8.27 m/s

2

Uncertainty K = 0.82 m/s

2

WARNING!

► The noise emission levels speciﬁed in these

instructions have been measured in ac-

cordance with the standardised measuring

procedure speciﬁed in ISO 15744 and can

be used to make equipment comparisons.

The noise emission values vary in accordance

with the use of the compressed air tool and

may be higher than the values speciﬁed in

these instructions in some cases. It is easy to

underestimate the noise emission load if the

compressed air tool is used regularly in a

certain manner.

NOTE

► For an accurate estimate of the noise emis-

sion load during a certain working period,

the times during which the appliance is

switched oﬀ or is running but not actually

being used must also be taken into considera-

tion. This can signiﬁcantly reduce the noise

emission load over the total working period.

WARNING!

General safety

instructions for

compressed air tools

WARNING!

► For multiple hazards: Please ensure that you

have read and understood the safety instruc-

tions before adjusting, operating, repairing,

maintaining or replacing accessories on

the sander or working in the vicinity of the

machine. Failure to do this can result in seri-

ous bodily injury.

■ The sanding machine for sanding sheets or the

polisher should only be adjusted, set or used by

adequately qualiﬁed and trained operators.

■ This sanding machine for sanding sheets or the

polisher may not be modiﬁed. Modiﬁcations can

reduce the eﬀectiveness of the safety measures

and increase the risks for the operator.

■ The safety instructions should not be lost – give

them to the operator.

■ Never use damaged sanding machines for

sanding sheets or polishers.

■ The appliance must be inspected regularly to

ensure that it is labelled with the required rated

values and markings given in this manual. The

user must contact the manufacturer to obtain

replacement labels if necessary.

Hazards caused by ﬂying parts

■ If a workpiece or accessory or even part of the

machine tool itself breaks, parts can be ﬂung

out at high speeds.

■ When operating the sanding machine for sand-

ing sheets or the polisher or when exchanging

accessories on the device, always wear eye

protection. The degree of necessary protection

must be evaluated separately for each individual

task.

■ Wear a safety helmet if working above head

height. In this case, the risks for others should

also be assessed.

■ You must ensure that the workpiece has been

securely ﬁxed.

4

PDEXS 150 B2

GB

IE

Hazards caused by entanglement

■ Suﬀocation, scalping or and/or cut wounds can

occur if loose clothing, jewellery, necklaces, hair

or gloves are not kept away from the machine

and its accessories.

Hazards during operation

■ When using the machine, the operator's hands

can be subject to hazards such as cuts, grazing

and heat. Wear suitable gloves to protect your

hands.

■ The operator and maintenance personnel must

be physically capable of handling the size,

mass and power of the machine.

■ Hold the machine correctly: be ready to coun-

teract any normal or sudden movements - have

both hands ready.

■ Ensure that your body is balanced and that you

have a secure standing position.

■ Release the start/stop control in case of a dis-

ruption to the electricity supply.

■ Use only lubricants recommended by the manu-

facturer.

■ Avoid direct contact with the movable grinding

disc to avoid squashing or cutting your hands or

other parts of the body. Always wear suitable

gloves to protect your hands.

■ Check the sanding disc before every use. Do

not use if this is cracked, broken or has been

dropped.

■ Avoid direct contact with the movable sanding

disc to avoid squashing or cutting your hands or

other parts of the body. Always wear suitable

gloves to protect your hands.

■ Never use the machine without an abrasive

attachment.

■ There is a risk of electrostatic discharge if the

machine is used on plastic and other non-

conductive materials.

■ Dust and vapours created by the sanding and

sanding can cause a potentially explosive at-

mosphere. Always use a dust extraction or sup-

pression system suitable for the material being

worked.

Risks due to repetitive movements

■ When using a sanding machine for sanding

sheets or a polisher to perform work-related

activities, operators may experience uncomfort-

able sensations in their hands and arms, as well

as in the neck and shoulders or other parts of

the body.

■ When using a sanding machine for sanding

sheets or a polisher, the operator should adopt

a comfortable posture whilst ensuring a secure

hold and avoiding awkward postures or posi-

tions in which it is diﬃcult to maintain balance.

The operator should change positions during

the course of long-lasting tasks. This can be

helpful in the prevention of discomfort and

fatigue.

■ If the operator notices symptoms such as persis-

tent or recurring illness, discomfort, throbbing,

pain, tingling, burning or stiﬀness, these indica-

tions should not be ignored.

In this case, the operator should consult a suitably

qualiﬁed physician.

Hazards caused by accessories

■ Disconnect the sanding machine for sanding

sheets or the polisher from the power supply

before ﬁtting or replacing the machine tools or

accessories.

■ Avoid direct contact with the machine tool during

and after use, since this can have heated up or

have become sharp.

■ Only machine tools which were designed by

the manufacturer for sanding machines with

sanding sheets and polishers may be used

for sanding machines for sanding sheets and

polishers.

■ Cutting discs and machines for cutting may not

be used.

■ Check whether the maximum operational speed

of the machine tool (buﬀs, sanding sheets, ﬁbre

discs etc.) is higher than the rated speed of the

machine;

■ Self-adhesive sanding discs must be applied

concentrically on the mounting plate.

5

PDEXS 150 B2

GB

IE

Hazards in the workplace

■ Slipping, tripping up and falling are the main

causes of injuries at the workplace. Take note

of surfaces which could have become slippery

through use of the machine, and also any trip-

ping hazards caused by air or hydraulic hoses.

■ These sanding machines for sanding sheets or

polishers are not intended for use in explosion-

capable atmospheres and is not insulated

against contact with electrical power sources.

■ Ensure that no electrical service lines, gas pipes,

etc. that could cause a hazard if damaged by

use of the machine are present.

Risks due to dust and vapours

■ The dust and vapours produced by using the

sanding machine for abrasive media and pol-

ishing can be hazardous to health (e.g. cause

cancer, birth defects, asthma and/or dermati-

tis); it is essential to carry out a risk assessment

in respect of these risks and to implement cor-

responding regulatory mechanisms.

■ The risk assessment should include all dust

caused by the use of the machine and any

existing dust that may be whirled up at the

same time.

■ The sanding machine for sanding sheets or

polisher is to be operated and maintained in ac-

cordance with the recommendations contained

in this manual to keep the release of dust and

vapours to a minimum.

■ The exhaust air should be routed so that the

raising of dust in already dusty environments is

kept to a minimum.

■ If dusts or vapours are created, the main priority

must be to control these at the site of their release.

■ All inserts or accessories of the machine intended

for collecting, extracting or suppressing airborne

dust or vapours or should be used and serviced in

accordance with the manufacturer’s instructions.

■ Consumables/machine tools should be se-

lected, maintained and replaced in accordance

with the recommendations in this guide in order

to avoid unnecessary intensiﬁcation of dust or

vapour production.

■ Use breathing equipment as per the instructions

provided by your employer or as required by

health and safety regulations.

Risks due to noise

■ Exposure to high noise levels can result in per-

manent hearing damage, loss of hearing and

other problems such as tinnitus (ringing, rushing,

whistling or buzzing in the ear) if suﬃcient hear-

ing protection is not worn. It is essential that a

risk assessment with regard to these hazards

is carried out and that appropriate regulating

mechanisms are implemented.

■ Suitable regulatory mechanisms include the use

of insulation materials to avoid pinging occurring

on the workpieces and similar measures.

■ Use ear protection equipment as per the instruc-

tions provided by your employer or as required

by health and safety regulations.

■ The sanding machine for sanding sheets or

polisher is to be operated and maintained in ac-

cordance with the recommendations contained

in this manual to reduce any unnecessary in-

crease of the noise levels.

■ Consumables/machine tools should be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary increase of the noise levels.

■ If the sanding machine for sanding sheets or

the polisher is equipped with a silencer, always

ensure that this in its place and is operational

while the machine is in operation.

6

PDEXS 150 B2

GB

IE

Risks due to vibrations

■ Vibrations can damage the nerves and cause

malfunctions to the blood circulation in the

hands and arms.

■ When working in a cold environment, wear warm

clothing and keep your hands warm and dry.

■ If you notice numbness, tingling or pain in your

ﬁngers or hands or notice that the skin of your

ﬁngers or hands has become pale, stop work-

ing with the sanding machine for sanding sheets

or the polisher, inform your employer and con-

sult a doctor.

■ The sanding machine for sanding sheets or

polisher is to be operated and maintained in ac-

cordance with the recommendations contained

in this manual to reduce any unnecessary in-

crease in vibration levels.

■ Hold the machine securely but not too ﬁrmly

while maintaining the necessary hand-reaction

force, as the vibration risk generally increases

the harder the machine is held.

Additional safety instructions for

pneumatic machines

■ Compressed air can cause serious injury.

– Ensure that the air supply is switched oﬀ,

the hose is not under pressure and that the

machine is disconnected from the air supply

when not in us, and also before exchanging

accessories or carrying out repairs.

– Never aim the airﬂow towards yourself or

any other person.

■ Thrashing hoses can cause serious injury. There-

fore, always check that the hoses and their ﬁx-

ings are not damaged or have not come loose.

■ If universal rotary joints (claw couplings) are

used, locking pins must be used to provide pro-

tection; Whipchek

®

air hose restraints must be

used to provide protection in case of a failure of

the connection of the hose to the machine.

■ Ensure that the maximum permissible pressure

stated on the machine is not exceeded.

■ Never carry compressed air-powered machines

by the hose.

Appliance-speciﬁc safety instructions

for sanders

WARNING!

■ Dusts from materials such as leaded paint,

some types of wood and metal can be harm-

ful to your health.

■ Contact with or inhalation of these dusts can

represent a health hazard for the person

operating the appliance and other people in

the vicinity.

■ Wear safety goggles and a protective dust

mask!

7

PDEXS 150 B2

GB

IE

Before use

NOTE

►

The sander may only be operated on

cleaned, oil-atomised compressed air and

may not exceed the maximum operating

pressure of 6.3 bar at the appliance. The

compressor must be ﬁtted with a pressure

reducer to regulate the working pressure.

► Wind the Teﬂon tape

supplied around all

threaded connectors.

Fitting the connector nipple

♦ Remove the plastic protective cap from the

appliance's air inlet.

♦ Wrap the threads on the connector nipple

with the Teﬂon tape supplied.

♦ Screw the connector nipple

into the air inlet.

Fitting the sanding disc

The compressed air-powered random orbital sander

is equipped with a protective cuﬀ .

■

Rotation direction indicator of the

sanding disc

♦ To ﬁt or replace the sanding disc invert the

protective cuﬀ (see Fig. 1).

Fig. 1

WARNING!

► Never operate the compressed air-powered

random orbital sander without the protective

cuﬀ

.

► Never operate the compressed air-powered

random orbital sander with an inverted

protective cuﬀ .

► A damaged protective cuﬀ should be

replaced immediately.

♦ Turn the spindle lock

with the knurled bulge

towards the ﬂat side of the eccentric spindle

(see Fig. 2).

Fig. 2

♦ Remove the protective cap from the threaded

rod of the sanding disc

and screw it clock-

wise into the eccentric spindle as far as the

stop.

♦ Undo the spindle lock

so that the eccentric

spindle can turn freely on its own axis.

CAUTION!

► Never operate the compressed air-powered

random orbital sander with a locked drive

spindle. This is dangerous and can result in

serious injuries.

♦ Evert the protective cuﬀ

again (see Fig. 3).

♦ Fig. 3

Selecting a sandpaper disc

Removal and surface:

The material removal rate and surface quality are

determined by the grain strength of the sandpaper.

■ Please note that you can use sandpapers with

various grain sizes for working the diﬀerent

materials.

8

PDEXS 150 B2

GB

IE

Fitting the sandpaper disc

CAUTION!

► Ensure that the appliance is disconnected

from the compressed air source before you

ﬁt or remove a sandpaper disc

.

♦ The sanding disc

and the supplied sandpaper

discs are equipped with matching Velcro

fasteners.

♦ Select the sandpaper disc

with the desired

grain and press it onto the sanding disc .

Ensure that it is centred.

♦ To change the sandpaper disc

, lift it from the

side and pull it oﬀ the sanding disc .

Clean the sanding disc as required with

compressed air.

Lubrication

NOTE

► To avoid friction and corrosion damage,

regular lubrication is particularly important.

We recommend using a suitable special oil

for compressed air appliances (e.g. Liqui Moly

compressor oil).

– Lubrication with mist oiler

– A mist oiler (not supplied) continuously

and optimally lubricates the appliance as

a preparation stage after the pressure re-

ducer. A mist oiler gives oﬀ ﬁne drops of

oil into the air ﬂow and thus guarantees

a regular lubrication.

– Manual lubrication

– If you do not have a mist oiler, lubricate

the appliance before every use or longer

work sessions by dripping 3–4 drops of

special oil for compressed air appliances

into the connector nipple

.

Reﬁlling oil

To ensure that the compressed air-powered random

orbital sander remains operational for as long as

possible, make sure that there is suﬃcient pneu-

matic oil in the appliance.

The following options are available:

♦ Attach a maintenance unit with an oiler to the

compressor.

♦ Install a ﬁtted oiler into the compressed air line

or the compressor.

♦ Add 3–5 drops of pneumatic oil into the con-

nector nipple

every 15 minutes of operation.

Connecting to a compressed air source

NOTE

► Before connecting the compressed air source

– the correct working pressure (3–6 bar)

must be fully reached

– make sure that the trigger is in the upper

position

♦ Attach the appliance to a compressor by con-

necting the connector nipple

with the supply

hose of the compressed air source.

♦ To ensure that you can regulate the air pressure,

the compressed air source must be equipped

with a pressure reducer.

9

PDEXS 150 B2

GB

IE

Operation

Switching on and oﬀ

Switching on:

♦ First press the locking mechanism forwards and

then the trigger

to switch the appliance on.

Switching oﬀ:

♦ Let go of the trigger

.

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

Regulation of vibration output

■

Use the speed controller

to control the air-

ﬂow and thus the vibration output (also during

operation).

■

The ideal speed depends on the material being

worked and can be determined through practical

tests.

Use the pressure reducer to set the correct working

pressure.

Sanding

♦ Switch on the compressed air source and allow

it to run until the maximum tank pressure has

been reached.

♦ Use the pressure reducer on the compressed

air source to set the optimum working pressure.

Note that the maximum working pressure may

not be exceeded. An excessive working pres-

sure does not mean increased output; it merely

increases the air consumption and accelerates

appliance wear. Always comply with the techni-

cal information.

♦ Switch on the compressed air-powered random

orbital sander.

♦ Allow the device to reach the required speed

and adjust as necessary.

♦ Guide the compressed air-powered random

orbital sander parallel onto the workpiece.

♦ Move the appliance parallel and in ﬂat circles

or alternatively lengthwise and across the sur-

face. Use the housing

as a handle to guide

the appliance in the desired direction.

♦ Do not press the compressed air-powered ran-

dom orbital sander down. Pressing down hard

does not increase the working eﬃciency!

♦ When you have ﬁnished working, let go of the

trigger

to switch oﬀ the appliance.

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

CAUTION!

► Sanding creates dust. Always wear protective

gloves, a suitable mask and clean the sand-

paper and workpiece at regular intervals with

a vacuum cleaner or compressed air.

► Suitable safety precautions must be taken

depending on the size and nature of the

workpiece. Use suitable clamping devices to

prevent the workpiece from slipping.

► In the event of an interruption to the air sup-

ply, release the trigger

immediately.

Working procedures

The most important thing to remember when sand-

ing is to use successively ﬁner grained paper.

With a coarse grain, the surface will not become

smooth, but rather rougher. If the grain is too ﬁne,

you will hardly achieve any noticeable result.

The material removal rate is determined by the

speed and grain size of the sandpaper.

The sandpaper used should be appropriate to the

substance being worked and the amount of mate-

rial to be removed.

CAUTION!

► Ensure that the appliance is disconnected

from the compressed air source before you ﬁt

or remove a sandpaper disc

.

10

PDEXS 150 B2

GB

IE

Material Grain

Paintwork: rubbing down 180

removing

scratches

120

removing rust 40

Wood: softwood 60–80

hardwood 60

plywood 240

Metal: aluminium 80

steel 60

Maintenance and cleaning

WARNING! RISK OF INJURY!

Disconnect the appliance from the

compressed air supply.

CAUTION!

► Before maintenance, clean oﬀ any hazardous

substances that may (due to working pro-

cesses) have accumulated on the appliance.

Avoid all skin contact with these substances.

If the skin comes into contact with hazardous

dusts, this can lead to severe dermatitis. If

dust is produced or swirled up during mainte-

nance, it can be inhaled.

NOTE

To ensure correct functioning and long-term

durability of the sander, pay attention to the

following points:

■ Suﬃcient and continuously intact oil lubrication

is highly important for optimum functioning.

■ Check the speed and vibration levels after each

use.

■ Check the idle speed regularly and after any

maintenance is performed:

use a rev counter and perform the measurement

without any clamped tools. The idle speed may

not be exceeded under any circumstances at a

residual pressure of 6.3 bar.

■ If the appliance is exhibiting excessive vibration

levels, the cause of the vibrations must be identi-

ﬁed and repaired.

■ Use only the genuine replacement parts recom-

mended by the manufacturer, otherwise you

could put users at danger. In doubt, contact the

Service Centre.

■ Check the sanding disc

regularly for damage.

■ Clean the appliance with a soft, dry cloth only.

■ Never use sharp or scratchy cleaning agents

under any circumstances.

Troubleshooting

Fault Possible

cause

Remedy

Speed too

slow, air

escapes from

the outlet.

Motor parts

jamming due

to dirt.

Check the

pressure sup-

ply ﬁlter for

contamination.

Pressure sup-

ply too low.

Check the

pressure sup-

ply ﬁlter for

contamination.

Lubricate

appliance as

described in

the instruc-

tions.

If necessary,

repeat the

steps outlined

above.

Appli-

ance does

not move;

compressed

air escapes

completely

through the

outlet.

Motor is

jammed due

to material

build-up.

Lubricate

appliance as

described in

the instruc-

tions.

11

PDEXS 150 B2

GB

IE

Disposal

The packaging consists of environmentally

friendly material. It can be disposed of in

the local recycling containers.

Do not dispose of the appliance in the normal

domestic waste!

Your local community or municipal authorities can

provide information on how to dispose of the worn-

out appliance.

Warranty

This appliance is provided with a 3-year

warranty valid from the date of purchase.

The appliance has been manufactured with

care and inspected meticulously prior to de-

livery. Please retain your receipt as proof of

purchase. In the event of a warranty claim,

please contact your Customer Service unit by

telephone. This is the only way to guarantee

free return of your goods.

The warranty only covers claims for material and

manufacturing defects, not for damage sustained

during carriage, components subject to wear and

tear or damage to fragile components such as

switches or batteries. This appliance is intended

solely for private use and not for commercial pur-

poses. The warranty shall be deemed void in cases

of misuse or improper handling, use of force and

modiﬁcations/repairs which have not been carried

out by one of our authorised Service centres. Your

statutory rights are not restricted by this warranty.

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking, but no later

than two days after the date of purchase. Repairs

carried out after expiry of the warranty period shall

be subject to charge.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

IAN 275679

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: k[email protected]

IAN 275679

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

12

PDEXS 150 B2

GB

IE

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu-

ments oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that

this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Applied harmonised standards:

EN ISO 11148-8: 2011

Type designation of machine:

Random orbital air sander PDEXS 150 B2

Year of manufacture: 03 - 2016

Serial number: IAN 275679

Bochum, 29/01/2016

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context

of further development is reserved.

13

PDEXS 150 B2

DK

Indholdsfortegnelse

Indledning ......................................................14

Anvendelsesområde .........................................................14

Udstyr .................................................................... 14

Pakkens indhold ............................................................14

Tekniske data ..............................................................14

Generelle sikkerhedsanvisninger for trykluftmaskiner .................15

Fare pga. udslyngede dele ...................................................15

Fare pga. indfangning .......................................................16

Fare under drift ............................................................. 16

Fare pga. gentagne bevægelser ............................................... 16

Fare pga. tilbehør ...........................................................16

Fare på arbejdspladsen ......................................................17

Fare på grund af støv og dampe ............................................... 17

Fare pga. støj .............................................................. 17

Fare pga. vibrationer ........................................................18

Yderligere sikkerhedsanvisninger til trykluftmaskiner ................................18

Maskinspeciﬁkke sikkerhedsanvisninger for slibere ................................. 18

Før første brug ..................................................18

Montage af tilslutningsnippel .................................................. 18

Montage af slibetallerken .................................................... 19

Valg af slibeskive ...........................................................19

Montage af slibeskive ....................................................... 19

Smøring .................................................................. 20

Påfyldning af olie ...........................................................20

Tilslutning til trykluftkilde ...................................................... 20

Betjening .......................................................20

Tænd/sluk ................................................................20

Regulering af oscillationseﬀekt ................................................. 20

Slibning ..................................................................21

Arbejdsanvisninger ..........................................................21

Vedligeholdelse og rengøring ......................................22

Afhjælpning af fejl ...............................................22

Bortskaﬀelse ....................................................23

Garanti ........................................................23

Service .........................................................23

Importør .......................................................23

Oversættelse af den originale overensstemmelseserklæring ............24

14

PDEXS 150 B2

DK

TRYKLUFT-EXCENTERSLIBER

PDEXS 150 B2

Indledning

Tillykke med købet af dit nye produkt. Du har valgt et

produkt af høj kvalitet. Betjeningsvejledningen er en

del af dette produkt. Den indeholder vigtige infor-

mationer om sikkerhed, anvendelse og bortskaﬀelse.

Du bør sætte dig ind i alle produktets betjenings- og

sikkerhedsanvisninger før brug. Brug kun produktet

som beskrevet og kun til de angivne anvendelsesom-

råder. Lad vejledningen følge med produktet, hvis du

giver det videre til andre.

Anvendelsesområde

Trykluftexcentersliberen er velegnet til slibning,

polering og forberedelse af forskellige overﬂader.

Enhver anden anvendelse eller ændring af produk-

tet anses for at være uden for anvendelsesområdet

og indebærer betydelige farer for uheld. Vi påta-

ger os intet ansvar for skader, der opstår som følge

af anvendelse uden for anvendelsesområdet. Pro-

duktet er kun beregnet til privat anvendelse.

Symboler på trykluftværktøjet:

WARNING!

Før første brug skal

betjeningsvejledningen

læses.

Det anbefales at bære

beskyttelseshandsker

og beskyttelsestøj.

Benyt altid øjenbeskyt-

telse ved anvendelse

eller vedligeholdelse

af slibemaskinen.

Benyt altid ånde-

drætsværn ved

støvudvikling.

Benyt altid høreværn.

Olieres dagligt

Rotationsretning

Udstyr

Hus

Aftrækkerlås

Aftrækkerarm

Håndtag

Tilslutningsnippel

Hastighedsregulator

Spindellås

Excenterspindel med slibetallerkenholder

Slibetallerken

Beskyttelseskrave

Slibeskive

Oliebeholder

Teﬂontape

Pakkens indhold

1 trykluft-excentersliber

1 m teﬂontape

1 oliebeholder

1 tilslutningsnippel 6,35 mm (1/4“)

1 slibetallerken Ø 150 mm (med velcro)

5 slibeskiver (P60/P80/P100/P120/P150)

1 betjeningsvejledning

Tekniske data

Dimensioneret hastighed: maks. 10000 min

-1

Dimensioneret lufttryk: maks. 6,3 bar

Slibetallerken: Ø 150 mm

Vægt (uden tilbehør): ca. 1,65 kg

15

PDEXS 150 B2

DK

Støjemissionsværdier:

Måleværdi for støj beregnet i henhold til

ISO 15744:

Lydtrykniveau: L

PA

= 90,4 dB (A)

Usikkerhed K

pA

= 3 dB

Lydeﬀektniveau: L

WA

= 101,4 dB (A)

Usikkerhed: K

WA

= 3 dB

Bær høreværn!

Vibrationsemissionsværdi:

Totalværdi for vibrationer målt iht. ISO 28927-3

og EN 12096:

a

h

= 8,27 m/s

2

Usikkerhed K = 0,82 m/s

2

ADVARSEL!

► Støjemissionsværdierne, som er angivet i

disse anvisninger, er målt med en måleme-

tode, der er standardiseret efter ISO 15744,

og som kan anvendes til sammenligning af

maskiner. Støjemissionsværdierne ændrer sig

afhængigt af trykluftværktøjets anvendelse og

kan i mange tilfælde ligge over de angivne

værdier i disse anvisninger. Støjemissionsbe-

lastningen kan undervurderes, hvis trykluft-

værktøjet anvendes jævnligt på denne måde.

BEMÆRK

► For at opnå en nøjagtig vurdering af støjemis-

sionsbelastningen i et bestemt arbejdstids-

rum er man også nødt til at medregne de

tidspunkter, hvor produktet er slukket, eller

ganske vist er tændt, men ikke anvendes.

Dette kan reducere støjemissionsbelastningen

over hele tidsrummet betydeligt.

WARNING!

Generelle sikkerheds-

anvisninger for

trykluftmaskiner

ADVARSEL!

► For ﬂere risici: Sikkerhedsanvisningerne skal

være læst og forstået før enhver justering,

betjening, reparation, vedligeholdelse af

slibe- eller poleringsmaskinen og før arbejde

i nærheden af maskinen. Hvis dette ikke er til-

fældet, kan det føre til alvorlige personskader.

■ Slibe- eller poleringsmaskinen må udelukkende

justeres, indstilles eller anvendes af behørigt

kvaliﬁcerede og uddannede operatører.

■ Denne slibe- eller poleringsmaskine må ikke

modiﬁceres. Modiﬁkationer kan reducere sik-

kerhedsanordningernes eﬀektivitet og forøge

risikoen for operatøren.

■ Sikkerhedsanvisningerne må ikke blive væk –

giv dem til operatøren.

■ Brug aldrig beskadigede slibe- eller polerings-

maskiner.

■ Maskinen skal jævnligt inspiceres for at kontrol-

lere, at den er mærket med de i vejledningen

foreskrevne nominelle værdier og markeringer.

Brugeren skal om nødvendigt kontakte produ-

centen for at få nye mærkater.

Fare pga. udslyngede dele

■ Ved brud på arbejdsemnet, tilbehørsdele eller

sågar selve maskinværktøjet kan der slynges

dele ud ved høj hastighed.

■ Ved betjening af slibe- eller poleringsmaskinen

eller ved udskiftning af tilbehørsdele på maskinen

skal der altid benyttes slagfast øjenbeskyttelse.

Graden af nødvendig beskyttelse skal vurderes

individuelt for hver enkelt anvendelse.

■ Ved arbejde over hovedhøjde skal der bæres

beskyttelseshjelm. I dette tilfælde skal også

risikoen for andre personer tages i betragtning.

■ Det skal sikres, at arbejdsemnet er sikkert fast-

gjort.

16

PDEXS 150 B2

DK

Fare pga. indfangning

■ Det kan føre til kvælning, skalpering og/eller

snitsår, hvis løstsiddende tøj, smykker, halskæ-

der, hår eller handsker ikke holdes væk fra

maskinen og dens tilbehørsdele.

Fare under drift

■ Ved anvendelse af maskinen kan operatørens

hænder blive udsat for risici som f.eks. snitsår,

hudafskrabninger eller brandsår. Bær derfor

egnede handsker til beskyttelse af hænderne.

■ Operatøren og vedligeholdelsespersonalet skal

fysisk være i stand til at håndtere maskinens

størrelse, vægt og eﬀekt.

■ Hold maskinen korrekt: Vær parat til at modvirke

sædvanlige eller pludselige bevægelser – hold

begge hænder klar.

■ Sørg for at kroppen er i god balance, og at du

har et godt fodfæste.

■ Deaktivér aftrækkeren i tilfælde af en afbrydelse i

energiforsyningen.

■ Brug kun de smøremidler, som anbefales af

producenten.

■ Beskyttelsesbriller er obligatorisk; det anbefales

at bære beskyttelseshandsker og beskyttelses-

tøj.

■ Kontrollér slibetallerknen før enhver anvendelse.

Brug den ikke, hvis den er revnet, knækket eller

har været tabt på gulvet.

■ Undgå direkte kontakt med den bevægelige

slibetallerken for at undgå kvæstelser eller snit-

sår på hænderne eller andre legemsdele. Der

skal bæres egnede handsker til beskyttelse af

hænderne.

■ Brug aldrig maskinen uden slibemiddel.

■ Der er risiko for elektrostatisk udladning, hvis

maskinen anvendes på plast eller andre ikke-

ledende materialer.

■ Støv og dampe, som udvikles ved slibning og

polering, kan føre til en potentielt eksplosiv

atmosfære. Brug altid et støvudsugnings- eller

undertrykkelsessystem, der passer til det bear-

bejdede materiale.

Fare pga. gentagne bevægelser

■ Ved anvendelse af en slibe- eller poleringsma-

skine til udførelse af arbejdsrelaterede aktivite-

ter kan operatøren muligvis opleve ubehagelige

fornemmelser i hænder og arme samt i hals- og

skulderregionen eller andre legemsdele.

■ Ved anvendelse af en slibe- eller poleringsma-

skine skal operatøren indtage en bekvem krops-

stilling, have et godt fast greb om maskinen og

undgå akavede arbejdsstillinger, som gør det

svært at holde balancen. Operatøren skal skifte

kropsstilling under langvarige arbejdsprocesser,

hvilket kan være med til at forebygge ubehag

og træthed.

■ Såfremt operatøren bemærker symptomer så-

som permanent eller gentagne tilfælde af ilde-

beﬁndende, ubehag, dunken, smerter, prikken,

følelsesløshed, brænden eller stivhed, må disse

symptomer ikke ignoreres. Operatøren skal i

så tilfælde konsultere en passende kvaliﬁceret

læge.

Fare pga. tilbehør

■ Afbryd slibe- eller poleringsmaskinen fra ener-

giforsyningen før udskiftning af maskinværktøj

eller tilbehørsdele.

■ Undgå direkte kontakt med maskinværktøjet

under og efter brugen, eftersom dette kan være

meget varmt eller have skarpe kanter.

■ Der må kun anvendes maskinværktøjer til slibe-

og poleringsmaskiner, der er godkendt af

maskinproducenten;

■ Skæreskiver og maskiner til skæring må ikke

anvendes.

■ Det skal kontrolleres om maskinværktøjets mak-

simale driftshastighed (lamelskiver, slibebånd,

ﬁberskiver osv.) er højere end maskinens nomi-

nelle rotationshastighed;

■ Selvklæbende slibeskiver skal placeres centreret

på montagepladen.

17

PDEXS 150 B2

DK

Fare på arbejdspladsen

■ En af hovedårsagerne til skader på arbejds-

pladsen er, at folk glider, snubler eller falder.

Vær opmærksom på overﬂader, som kan være

blevet glatte ved brug af maskinen, og på

risikoen for at snuble over trykluft- eller hydrau-

likslanger.

■ Disse slibe- og poleringsmaskiner er ikke egnet

til anvendelse i eksplosionsfarlige atmosfærer

og er ikke isoleret mod kontakt til elektriske

strømkilder.

■ Tjek at der ikke ﬁndes nogle elektriske lednin-

ger, gasrør mv. i nærheden, som kan føre til

farlige situationer, hvis de bliver beskadiget

under brug af maskinen.

Fare på grund af støv og dampe

■ Det støv og de dampe, som opstår ved anven-

delse af slibe- og poleringsmaskiner, kan føre til

sundhedsfarlige skader (som f.eks. kræft, fød-

selsdefekter, astma og/eller dermatitis); der skal

altid foretages en risikovurdering i forbindelse

med disse farer og implementeres passende

beskyttelsesmekanismer.

■ Risikovurderingen skal omfatte alle de støvtyper,

som dannes ved brug af maskinen og even-

tuelle andre støvtyper, som bliver hvirvlet op

samtidig.

■ Slibe- eller poleringsmaskinen skal drives og

vedligeholdes i overensstemmelse med anbe-

falingerne i denne vejledning for at reducere

frigivelsen af støv og dampe til et minimum.

■ Udsugningsluften skal bortledes på en sådan

måde, at ophvirvling af støv i støvfyldte miljøer

reduceres til et minimum.

■ Såfremt der opstår støv eller dampe, må hoved-

opgaven være at kontrollere disse på det sted,

hvor de frigives.

■ Alle indsatser eller tilbehørsdele på maskinen

til opsamling, udsugning eller bekæmpelse af

ﬂyvestøv eller dampe skal anvendes og vedlige-

holdes i henhold til producentens anvisninger.

■ Forbrugsmaterialer/maskinværktøjer skal udvæl-

ges, vedligeholdes og udskiftes efter anbefalin-

gerne i denne vejledning for at undgå unødig

intensivering af støv- eller dampudviklingen.

■ Brug åndedrætsværn i henhold til din arbejds-

givers anvisninger eller som krævet i henhold til

arbejdsmiljøreglerne.

Fare pga. støj

■ Udsættelse for høje støjniveauer kan ved util-

strækkelig beskyttelse af hørelsen føre til perma-

nente høreskader, høretab og andre problemer

som f.eks. tinnitus (ringen, susen, hylen eller

summen i ørerne). Der skal altid foretages en

risikovurdering i forbindelse med disse farer og

implementeres passende beskyttelsesmekanismer.

■ Passende beskyttelsesmekanismer omfatter

f.eks. også anvendelse af isoleringsmaterialer

for at undgå høje ringelyde på emnerne.

■ Brug høreværn i henhold til din arbejdsgivers

anvisninger eller som krævet i henhold til ar-

bejdsmiljøreglerne.

■ Slibe- eller poleringsmaskinen skal drives og

vedligeholdes i overensstemmelse med anbe-

falingerne i denne vejledning for at undgå en

unødig forhøjelse af støjniveauet.

■ Forbrugsmaterialer/maskinværktøjer skal ud-

vælges, vedligeholdes og udskiftes efter anbe-

falingerne i denne vejledning for at undgå en

unødig forøgelse af støjniveauet.

■ Hvis slibe- eller poleringsmaskinen er udstyret

med en lyddæmper, skal du altid sikre dig, at

denne er monteret og funktionsdygtig, når

maskinen er i drift.

La page charge ...

Parkside 275679 Instructions Manual

Ce manuel convient également à

Parkside 275679 Instructions Manual

dans d''autres langues

Documents connexes

Autres documents