ASROCK 939Dual-SATA2 Le manuel du propriétaire

11

1

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published June 2005

22

2

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 19 Chassis Fan Connector (CHA_FAN1)

2 ATX Power Connector (ATXPWR1) 20 Clear CMOS Jumper (CLRTC1)

3 CPU Fan Connector (CPU_FAN1) 21 USB 2.0 Header (USB67, Blue)

4 ATX 12V Power Connector (ATX12V1) 22 USB 2.0 Header (USB45, Blue)

5 CPU Heatsink Retention Module 23 Flash Memory

6 939-Pin CPU Socket 24 Floppy Connector (FLOPPY1)

7 2 x 184-pin DDR DIMM Slots 25 Infrared Module Header (IR1)

(Dual Channel A: DDR1, DDR2; Blue) 26 Game Port Header (GAME1)

8 2 x 184-pin DDR DIMM Slots 27 Front Panel Audio Header (AUDIO1)

(Dual Channel B: DDR3, DDR4; Black) 28 JR1 JL1 Jumper

9 North Bridge Controller 29 PCI Slots (PCI1- 3)

10 Serial ATAII Connector (SATAII_1, red) 30 AGP Slot (1.5V_AGP1)

11 JMicron JMB360 Chipset (PCIEX1 interface) 31 J9 / J10 Jumper

12 South Bridge Controller 32 PCI EXPRESS Slot (PCIE2)

13 Secondary Serial ATA Connector (SATA2) 33 J11 Jumper

14 Primary Serial ATA Connector (SATA1) 34 PCI EXPRESS Slot (PCIE1)

15 Primary IDE Connector (IDE1, Blue) 35 Future CPU Port (FUTURE_CPU_PORT1)

16 Secondary IDE Connector (IDE2, Black) 36 Internal Audio Connector: CD1 (Black)

17 System Panel Header (PANEL1) 37 J1-J8 Jumpers

18 Chassis Speaker Header (SPEAKER 1)

33

3

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

ASRock 8CH I/OASRock 8CH I/O

ASRock 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 Serial Port: COM1

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

44

4

ASRock 939Dual-SATA2 Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock 939Dual-SATA2 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website

as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock 939Dual-SATA2 Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

1 x ASRock 939Dual-SATA2 Quick Installation Guide

1 x ASRock 939Dual-SATA2 Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x ASRock 8CH I/O Shield

EnglishEnglish

English

55

5

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform: ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

CPU: 939-Pin Socket Supporting AMD Athlon

TM

64 / 64FX Processor

Supports AMD’s Cool ‘n’ Quiet

TM

Technology (see CAUTION 1)

Chipsets: North Bridge:

ULi

®

M1695 chipset

For 939-Pin CPU, FSB @ 1 GHz / 2.0 GT/s

South Bridge:

ULi

®

M1567 chipset, supports SATA 1.5Gb/s

Memory: 4 x DDR DIMM Slots:

4 DIMMs support PC3200 (DDR 400) / PC2700 (DDR 333) /

PC2100 (DDR 266), Max. 4GB

Dual Channel Memory Technology support (see CAUTION 2)

IDE: IDE1: ATA 133 / Ultra DMA Mode 6

IDE2: ATA 133 / Ultra DMA Mode 6

Supports up to 4 IDE Devices

Serial ATA: Supports up to 2 SATA devices at 1.5Gb/s data transfer rate

(No support for “Hot Plug” functions)

Serial ATA II: 1 SATA II device at 3.0Gb/s data transfer rate

(No support for “Hot Plug” functions)

Floppy Port: Supports up to 2 Floppy Disk Drives

Audio: 7.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), Supports Wake-On-LAN

Hardware Monitor: CPU Temperature Sensing

Motherboard Temperature Sensing

CPU Overheat Shutdown to Protect CPU Life

(ASRock U-COP)(see CAUTION 3)

CPU Fan Tachometer

Chassis Fan Tachometer

Voltage Monitoring: +12V, +5V, +3.3V, Vcore

Future CPU Port: Supports CPU upgrade from AMD 939-Pin CPU to other future

CPU, such as 940-Pin CPU (M2)

(see page 9 for details)

PCI Slots: 3 x PCI Slots, PCI Specification 2.2

PCI EXPRESS Slots: 1 slot with PCIE x 16, 1 slot with PCIE x 1;

PCIE Specification 1.0a

AGP Slot: 1 x AGP Slot

Supports 1.5V, 8X / 4X AGP Card (see CAUTION 4)

USB 2.0: 8 USB 2.0 Ports:

4 Ready-to-Use USB 2.0 Ports on the I/O Panel

Plus 2 On-Board Headers Supporting 4 Extra USB 2.0 Ports

(see CAUTION 5)

66

6

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

ASRock 8CH I/O: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port

1 Serial Port: COM1

1 Parallel Port (ECP/EPP Support)

4 Ready-to-Use USB 2.0 Ports

1 RJ-45 Port

Audio Jack: Side Speaker / Rear Speaker / Central/Bass /

Line In / Front Speaker / Microphone

(see CAUTION 6)

BIOS: AMI Legal BIOS

Supports “Plug and Play”

ACPI 1.1 Compliance Wake Up Events

SMBIOS 2.3.1 Support

CPU Frequency Stepless Control

(only for advanced users’ reference, see CAUTION 7)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP / XP 64-bit

compliant

CAUTION!

1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’

Quiet

TM

technology under Windows system. See APPENDIX on page 40 of

“User Manual” in the Support CD to enable AMD’s Cool ‘n’ Quiet

TM

technology.

2. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 8 for proper installation.

3. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

4. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

5. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 / 2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/ ME.

6. For microphone input, this motherboard supports both stereo and mono modes.

For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,

and 8-channel modes. Please check the table on page 3 for proper connection.

7. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

77

7

ASRock 939Dual-SATA2 Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

88

8

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

2.2 Installation of Memory Modules (DIMM)2.2 Installation of Memory Modules (DIMM)

2.2 Installation of Memory Modules (DIMM)

939Dual-SATA2 motherboard provides four 184-pin DDR (Double Data Rate)

DIMM slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install identical (the same brand, speed,

size and chip-type) DDR DIMM pair in the slots of the same color. In other words,

you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and

DDR2; Blue slots; see p.2 No.7) or identical DDR DIMM pair in Dual Channel B

(DDR3 and DDR4; Black slots; see p.2 No.8), so that Dual Channel Memory

Technology can be activated. This motherboard also allows you to install four

DDR DIMMs for dual channel configuration, and please install identical DDR

DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration

Table below.

Dual Channel Memory Configurations

DDR1 DDR2 DDR3 DDR4

(Blue Slot) (Blue Slot) (Black Slot) (Black Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR1 and DDR2), or in the set of black slots (DDR3 and DDR4).

2. If only one memory module or three memory modules are installed

in the DDR DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDR1

and DDR3, it is unable to activate the Dual Channel Memory Tech-

nology .

99

9

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

STEP 1: Unlock a DIMM slot by pressing the retaining clips outward.

STEP 2: Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

STEP 3: Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

2.32.3

2.3

Expansion SlotsExpansion Slots

Expansion Slots

(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)

(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)

There are 1 Future CPU Port, 3 PCI slots, 2 PCIE slots, and 1 AGP slot on 939Dual-

SATA2 motherboard.

Future CPU Port (Yellow-Colored Port):

Future CPU Port allows you to upgrade your AMD 939-Pin CPU to AMD 940-Pin CPU by

installing an add-on ASRock M2CPU Board into this future CPU Port on 939Dual-

SATA2 motherboard. Before you upgrade the 939-Pin CPU to the 940-Pin (M2) CPU,

it is necessary to adjust the jumper settings for those required jumpers on 939Dual-

SATA2 motherboard. Please refer to the table below for the correct jumper settings.

1010

10

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

This yellow-colored Future CPU Port is not an AGP slot! Please do

NOT insert any AGP card into it!

CPU Type Jumper Settings

939-Pin CPU

(Default)

940-Pin (M2)

CPU

(Using add-on

ASRock M2CPU

Board)

J1 J2

J3 J4

J5 J6

J7 J8

J11

J10

J9

J1 J2

J3 J4

J5 J6

J7 J8

J11

J10

J9

NOTE

When adjusting the jumper settings, you may use the tool, Jumper Cap Remover, to help you

removing the jumper caps more easily. This Jumper Cap Remover is bundled in your motherboard

package, and please follow the “Jumper Cap Remover Instruction” to use it properly.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots: PCIE1 (PCIE x 16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

PCIE2 (PCIE x 1 slot) is used for PCI Express cards, such as

Gigabit LAN card, SATA2 card, etc.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has

a special design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this

motherboard! It may cause permanent damage! For the voltage infor-

mation of your AGP card, please check with the AGP card vendors.

1111

11

ASRock 939Dual-SATA2 Motherboard

Short Open

2.5 Jumpers Setup2.5 Jumpers Setup

2.5 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on the pins, the jumper is “Open”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap

is placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1 JL1 Jumper

(see p.2, No. 28)

Note: If the jumpers JR1 and JL1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS Jumper

(CLRTC1)

(see p.2, No. 20)

Note: CLRTC1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

EnglishEnglish

English

8

J

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screw

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

2.42.4

2.4

Surround Display FeatureSurround Display Feature

Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on

PCI VGA card and PCI Express VGA card, you can easily enjoy the benefits of

Surround Display feature. For the detailed instruction, please refer to the docu-

ment at the following path in the Support CD: ..\ Surround Display

Clear CMOSDefault

1212

12

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 24)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 No. 15) (39-pin IDE2, see p.2 No. 16)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 No. 14) connectors support SATA data

(SATA2: see p.2 No. 13) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA II Connector This Serial ATA II (SATA II)

(SATA II_1: see p.2 No. 10) connector supports SATA II

data cables for internal storage

devices. The current SATA II

interface allows up to 3.0 Gb/s

data transfer rate.

SATA II_1

It is recommended to plug SATAII HDD to SATAII connector (SATAII_1) and

connect SATA HDD to SATA connector (SATA1 or SATA2).

on CLRTC1 for 5 seconds. However, please do not clear the CMOS right after

you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

connect the black end

to the IDE devices

the red-striped side to Pin1

SATA1

SATA2

1313

13

ASRock 939Dual-SATA2 Motherboard

CD1

connect to the

power supply

connect to the SATA

HDD power connector

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB67) dates 4 default USB 2.0 ports. If

(see p.2 No. 21) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB45) dates 4 default USB 2.0 ports. If

(see p.2 No. 22) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 25) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 36) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 27) convenient connection and

control of audio devices.

EnglishEnglish

English

1414

14

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 17) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 18)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 19) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(3-pin CPU_FAN1) cable to this connector and

(see p.2 No. 3) match the black wire to the

ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 2)

ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 4) ATX 12V plug to this connector.

Failing to do so will cause power

up failure.

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 26) is installed.

1515

15

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

2.72.7

2.7

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts JMicron JMB360 chipset that supports Serial ATAII

(SATAII) hard disk. It also adopts ULi M1567 south bridge chipset that supports

Serial ATA (SATA) hard disks, and supports RAID functions. You may install SATA

hard disks on this motherboard for internal storage devices. This section will

guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

1. If you plan to use RAID 0, RAID 1, or JBOD functions on SATA, SATA

HDDs must be operated in “RAID” mode.

2. “RAID” and “non-RAID” mode are options under “SATA Operation Mode” in

BIOS setup. Please refer to page 30 of “User Manual” in the Support CD for

details. They need different drivers during actual operation.

1616

16

ASRock 939Dual-SATA2 Motherboard

EnglishEnglish

English

2.82.8

2.8

Making a SAMaking a SA

Making a SA

TT

T

A Driver DiskA Driver Disk

A Driver Disk

ette Fette F

ette F

or SAor SA

or SA

TT

T

A Operation inA Operation in

A Operation in

“RAID” Mode“RAID” Mode

“RAID” Mode

If you want to install Windows 2000, Windows XP, or Windows XP 64-bit OS on your

SATA HDDs, you will need to make a SATA driver diskette before you start the OS

installation.

STEP 1: Insert the ASRock Support CD into your optical drive to boot your system.

(Do NOT insert any floppy diskette into the floppy drive at this moment!)

STEP 2: During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

STEP 3: When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

STEP 4: Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

STEP 5: The system will start to format the floppy diskette and copy SATA drivers

into the floppy diskette.

2.92.9

2.9

SASA

SA

TT

T

A Operating in “non-RAID” ModeA Operating in “non-RAID” Mode

A Operating in “non-RAID” Mode

If you want to install Windows 2000, Windows XP, or Windows XP 64-bit OS on your

SATA HDDs operating in non-RAID mode, you don’t need to make a SATA driver

diskette before OS installation.

Windows 98 SE and Windows ME must be installed by SATA operating in

RAID mode, and you don’t need to make a SATA driver diskette for these

two OS before OS installation.

Once you have the SATA driver diskette ready, you may start to install Windows 2000

/ Windows XP / Windows XP 64-bit on your system directly without setting the RAID

configuration on your system, or you may start to use “RAID Installation Guide” to set

RAID 0 / RAID 1 / JBOD configuration before you install the OS. Before you start to

configure the RAID function, you need to check the installation guide in the Support CD

for proper configuration. Please find the document, “Guide to SATA Hard Disks Installa-

tion and RAID Configuration”, at the following path in the Support CD:

.. \ Information \ Manual \ RAID Installation Guide \ English.pdf

1717

17

ASRock 939Dual-SATA2 Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP / XP 64-bit. The Support CD that came with the motherboard contains

necessary drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file “ASSETUP.

EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

2.102.10

2.10

SASA

SA

TT

T

AII Operating in “IDE” ModeAII Operating in “IDE” Mode

AII Operating in “IDE” Mode

If you want to install Windows 98 SE, Windows ME, Windows 2000, Windows XP, or

Windows XP 64-bit OS on your SATAII HDDs operating in IDE mode, you don’t need

to make a SATAII driver diskette before OS installation.

2.112.11

2.11

Making a SAMaking a SA

Making a SA

TT

T

AII Driver DiskAII Driver Disk

AII Driver Disk

ette Fette F

ette F

or SAor SA

or SA

TT

T

AII OperationAII Operation

AII Operation

in “SAin “SA

in “SA

TT

T

A” ModeA” Mode

A” Mode

If you want to install Windows 2000, Windows XP, or Windows XP 64-bit OS on your

SATAII HDDs, you will need to make a SATAII driver diskette before you start the OS

installation. You need to copy the SATAII driver package to a diskette and use it while

OS queries for other boot device driver diskette. (Please see the “Readme.txt” in

SATAII driver directory on the support CD for the files needed to copy to the diskette.)

1818

18

ASRock 939Dual-SATA2 Motherboard

1919

19

ASRock 939Dual-SATA2 Motherboard

‘ ’ ™

®

2020

20

ASRock 939Dual-SATA2 Motherboard

®

‘ ’

™

‘ ’ ™

La page est en cours de chargement...

ASROCK 939Dual-SATA2 Le manuel du propriétaire

ASROCK 939Dual-SATA2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents