Best UP26M48SB Guide d'installation

UP26M SERIES

HB0029

INSTALLATION INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 13 AND 14.

READ AND SAVE THESE INSTRUCTIONS

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770

To register your product online or for additional information visit www.BestRangeHoods.com

SV21517 rev. 04

! !

2

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA) and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any additional solid-state speed

control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. When applicable local regulations comprise more

restrictive installation and/or certification requirements,

the aforementioned requirements prevail on those of this

document and the installer agrees to conform to these at his

own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impeller, keep drywall spray, construction dust, etc. off power

unit.

4. Your hood motor has a thermal overload which will

automatically shut off the motor if it becomes overheated. The

motor will restart when it cools down. If the motor continues to

shut off and restart, have the hood serviced.

5. For best capture of cooking impurities, the bottom of the hood

should be at a minimum of 24” and at a maximum of 36” above

the cooking surface.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls

or ceiling or into attics, crawl space or garage.

8. This product is equipped with a thermostat which may start

blower automatically. To reduce the risk of injury and to prevent

power from being switched on accidentally, switch power off at

service panel and lock or tag service panel.

9. Because of the high exhausting capacity of this unit, you

should make sure enough air is entering the house to replace

exhausted air by opening a window close to or in the kitchen.

10. To reduce the risk of fire and electric shock, the Best UP26M

Series hood must be installed with Best interior blower model

iQ6, P3, P5, P6 or P8; Best exterior models EB6, EB9, EB12

or EB15; Best in-line blowers models ILB3, ILB6, ILB9 or

ILB11. Other blowers cannot be substituted. (Blowers sold

separately.)

11. Please read specification label on product for further

information and requirements.

WARNING

!

CAUTION

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you know how to

operate it.

B. The fire is small and contained in the area where it started.

C. The fire department has been called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

!

3

HL0220

- UP26M SERIES RANGE HOOD SYSTEM -

INTERIOR BLOWERS

MODEL 647

(7” ROUND WALL CAP)

MODEL 634 OR 644

(ROOF CAP)

8” R

OUND

STANDARD

DUCT

MODEL 413

TRANSITION

(3¼” X 10” TO 8”)

M

ODEL 459 TRANSITION

(3¼” X 14” TO 8”)

M

ODEL 643

(8” ROUND WALL CAP)

A

DAPTER/DAMPER

3¼” X 14”

(SUPPLIED WITH P8 BLOWER)

UP26M HOOD

MODEL 412

TRANSITION

(3¼” X 10” TO 7”)

M

ODEL 407

(7” ROUND—

2 FT SECTIONS)

M

ODEL 415

7” ROUND

ADJUSTABLE

ELBOW

(OPTIONAL)

8” ROUND ADJUSTABLE

ELBOW (OPTIONAL)

STANDARD

3¼” X 14” DUCT

FLOW DEVIATOR

(VERTICAL EXHAUST ONLY)

(SUPPLIED WITH P5 AND P8 BLOWERS)

A

DAPTER/DAMPER 3¼” X 10”

(SUPPLIED WITH P5 AND P8

BLOWERS)

R

OUGH-IN KIT

(SUPPLIED WITH P5 AND P8 BLOWERS)

MODEL P5

SINGLE-BLOWER (500 CFM)

BACKSPLASH (RMP SERIES)

(STAINLESS STEEL WALL COVERING

WITH WARMING SHELVES. OPTIONAL)

M

ODEL P8 DUAL-BLOWER (900 CFM)

FOR USE WITH 36” HOODS OR WIDER

NOTE: The dual blower P8 must

be installed with 3¼” x 14”

duct. If it is impossible to

connect the dual blower P8

to a 3¼” x 14” duct, use a

3¼” x 10” duct. In that case,

the blower performance will

be decreased by 25%.

STANDARD

3¼” X 10”

DUCT

MODEL 634 OR 644

(ROOF CAP)

UP26M HOOD

MODEL 438

8” ROUND ADAPTER/DAMPER

(SUPPLIED WITH P3, P6 AND

IQ6 BLOWERS)

ROUGH-IN KIT

(SUPPLIED WITH P3, P6 AND IQ6 BLOWERS)

MODELS P3 (300 CFM), P6 (600 CFM)

OR IQ6 (600 CFM) SINGLE BLOWER

MODEL 643

(8” ROUND WALL CAP)

MODEL 408

8” ROUND

STANDARD DUCT

MODEL 432

8” ROUND ADJUSTABLE

ELBOW (OPTIONAL)

4

HL0071

- UP26M SERIES RANGE HOOD SYSTEM -

IN-LINE AND EXTERIOR BLOWERS

MODEL 441

(10” R

OUND WALL CAP)

M

ODEL 437

(H

IGH CAPACITY ROOF CAP)

MODEL ILB9 (800 CFM)

OR ILB11 (1100 CFM)

IN-LINE BLOWER

(INCLUDES TWO 8” X 12” TO

10’’ ROUND TRANSITIONS)

M

ODEL 418

(10” ROUND

ADJUSTABLE ELBOW)—

OPTIONAL

MODEL 421

(10” ROUND VERT.

IN-LINE DAMPER)

(RECOMMENDED FOR USE

WITH EXTERIOR BLOWERS)

MODEL EB6 (600 CFM)

OR EB9 (900 CFM)

EXTERIOR BLOWER

MODEL EB12 (1200 CFM)

OR EB15 (1500 CFM)

EXTERIOR BLOWER

MODEL 410

(10” ROUND DUCT

—2FT. SECTIONS)

IN-LINE AND EXTERIOR BLOWER ROUGH-IN KIT

(INCLUDED WITH EB6, EB9, EB12, EB15,

ILB3, ILB6, ILB9 AND ILB11 BLOWERS).

UP26M

HOOD

MODEL ILB3 (280 CFM)

IN-LINE BLOWER

(INCLUDES ONE 8” TO 10”

ROUND TRANSITION)

MODEL ILB6 (600 CFM)

IN-LINE BLOWER

(INCLUDES TWO 4½” X 18½”

TO 10’’ ROUND TRANSITIONS)

MODEL 643

(8” ROUND

WALL

CAP)

RMP SERIES BACKSPLASH

(STAINLESS STEEL WALL

COVERING WITH WARMING

SHELVES. OPTIONAL)

M

ODEL 441

(10” ROUND

WALL CAP)

5

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower or in-line blower may be used with this hood. The Best UP26M must be installed with blower models iQ6,

P3, P5, P6, P8, ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted. (Blowers sold separately).

Plan where and how the ductwork will be installed.

If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 3, 5, 8, 11, 12, 16 and up of this

manual.

Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 7” or 8” round ducts, use a

transition. Use 2” metal foil duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 24”. A maximum of 36” above cooktop is highly recommended

for best capture of cooking impurities.

Distances over 36” are at the installer and users discretion.

3¼” x 10”

OR 3¼” x 14”

HH0213A

24” TO 36”

ABOVE COOKING SURFACE

ROOF CAP

WALL

CAP

HOOD

7” OR 8”

ROUND DUCT

3¼” X 10” TO 7”

OR 8” TRANSITION

OR 3¼”

X 14” TO 8”

TRANSITION

HH0214A

24” TO 36”

ABOVE COOKING SURFACE

ROOF CAP

WALL

CAP

HOOD

10” ROUND DUCT

EXTERIOR BLOWER

HH0217A

EXTERIOR

BLOWER

24” TO 36”

ABOVE COOKING SURFACE

MODEL P5 (SINGLE) OR P8 (DOUBLE)

INTERIOR BLOWER

TYPICAL RECTANGULAR DUCTWORK

MODEL P5 (SINGLE) OR P8 (DOUBLE)

INTERIOR BLOWER

7” OR 8” ROUND DUCTWORK

MODEL EB6, EB9, EB12 OR EB15

EXTERIOR BLOWER

TYPICAL DUCTWORK

HH0212A

IN-LINE BLOWER

10” ROUND DUCT

(

EXCEPT HLB3, 8’’ ROUND DUCT)

24” TO 36”

ABOVE COOKING SURFACE

ROOF CAP

WALL

CAP

HOOD

MODEL ILB3, ILB6, ILB9 OR ILB11

IN-LINE BLOWER

TYPICAL DUCTWORK

8” ROUND DUCT

HH0215A

24” TO 36”

ABOVE COOKING SURFACE

ROOF CAP

WALL

CAP

HOOD

MODEL P3, P6 or iQ6 (SINGLE)

INTERIOR BLOWER

8” ROUND DUCTWORK

6

2. PREPARE INSTALLATION

WARNING

!

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.

Make sure that the following items are included:

- Range hood

- Accessories: • Hybrid baffle filters with handles

• Shielded halogen bulbs (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base)

• Bag of parts including: 4 lock nuts no. 10-32, 1 wire clamp LP16-AP, 2 no. 6 x 1/2” screws,

2 wire connectors no. 74B, 6 no. 8 x 3/8”, 8 double threaded screws 6-12 x 1/2”

Parts sold separately:

• Interior blower Model P5 or P8 includes blower, rough-in kit, flow deviator and 3¼” x 10” or 3¼” x 14” adapter

• Interior blower Model iQ6, P3 or P6 includes blower, rough-in kit, adapter/damper

• In-line blower assembly ILB3, ILB6, ILB9 or ILB11 (all include transition(s) and rough-in plate)

• Exterior blower assembly EB6, EB9, EB12 or EB15 (all include rough-in plate)

• Backsplash (optional)

• Transitions, duct, elbows, dampers, wall and roof caps. Refer to pages 3 and 4 for a complete list of venting options and model numbers.

NOTE: For cabinets with recessed bottom, attach wood filler strips (not included) on each sides, as shown below. Use two 2-inch wide

strips for 30” wide hoods, and four 2-inch wide strips for wider hoods, cut to length. See below for wood filler strip locations.

HOOD

WIDTHS

LOCATIONS

ABC

30” 2” N/A N/A

36” 2” 4½” 4½”

42” 2” 7¼” 8¼”

48" 4” 10¼” 11¼”

HD0079

A

B C

3. INSTALL BACKSPLASH (OPTIONAL)

Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. In order to be

able to install the backsplash, ensure to have at least 18” clearance between bottom of hood and range control panel or cooktop. (See

instructions packed with backsplash.)

4. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)

INTERIOR BLOWER: Follow all subsequent steps of this manual.

EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 5, 8, 11,12, 16 and up of the present manual.

7

6. CHOOSE THE OPENING (P5 AND P8 BLOWERS ONLY)

Removing horizontal knockout opening on back of hood.

CAUTION

If using P5 blower, remove 10” wide knockout. If using P8 blower, remove either 10” or 14” wide knockout.

Remove the knockout for the chosen opening (horizontal at the back of the hood or vertical on rough-in plate). See pictures below.

14” KNOCKOUT

10” KNOCKOUT

HD0076

14

”

KNOCKOUT

HD0077

10”

KNOCKOUT

Removing vertical knockout opening on rough-in plate.

5. REMOVE FILTERS AND BOTTOM PANEL (ALL BLOWERS)

Lay the hood flat on a table. Use a piece of cardboard to avoid

damaging the table or the hood.

Remove tape on filters. Remove filters from hood and set aside.

NOTE: It is recommended to start with the center one(s).

HD0542

HD0541

RETAINING SCREWS

BOTTOM PANEL

Remove bottom panel both retaining screws. Set bottom panel and screws aside.

HD0544

1

3

2

8

10. INSTALL THE ADAPTER (P5 AND P8 BLOWERS ONLY)

Using provided screws, secure the adapter to the top (or back) of the hood. Seal the adapter to the hood using metal foil duct tape.

NOTE: For vertical exhaust, ensure that the damper pivot is located towards the front of the hood.

HD0005 HD0006

YOU MUST install the deviator if you choose to vent the hood vertically. Install the deviator as

shown.

NOTE: If installed correctly, the deviator will protrude about 1/8” above the rough-in plate.

8. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS)

INTERIOR BLOWER: Secure the rough-in plate (provided with the

blower) inside the hood with four lock nuts. See

picture at right.

EXTERIOR OR IN-LINE BLOWER: Refer to instructions included with

exterior or in-line blower rough-in kit.

Secure the rough-in plate inside the

hood with four lock nuts.

9. INSTALL THE DEVIATOR (P5 AND P8 BLOWERS, VERTICAL INSTALLATION ONLY)

HD0003

Inserting deviator into hood vertical opening.

HD0048

BLOWER PLATE

LOCK NUTS

Attach 8” round adapter/damper to blower rough-in plate.

Use metal duct tape to make all joints secure and air-tight.

7. INSTALL THE ADAPTER/DAMPER (P3, P6 AND IQ6 BLOWERS ONLY)

HO0196

9

12. CONNECT WIRING (ALL BLOWERS)

WARNING

!

Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable

codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting

means to prevent power to be switched on accidentally.

INTERIOR BLOWER: Connect cable into wiring box using wire connectors.

Connect wires as follow: BLACK to BLACK, WHITE to WHITE and

GREEN or bare wire under ground screw. Reinstall wiring cover.

DO NOT FORGET TO CONNECT THE GROUND.

IN-LINE OR EXTERIOR BLOWER: Remove rough-in plate wiring cover and connect wiring (see instructions included with in-line or

exterior blower).

HE0012

GROUND SCREW

11. INSTALL THE HOOD (ALL BLOWERS)

Run power cable to installation location. Place the hood to its location. Mark the position of the screws (smaller part of the key holes)

with a pen. Remove the hood and install the (8) 1/2” double thread screws leaving a 1/8” gap (4 screws for 30” hood). Remove wiring

cover, place the wire clamp, insert the cable in the hood and tighten the wire clamp to secure the cable. Place the hood under the

cabinet and slide it in position. Make sure the adapter/damper assembly enters the ducting. Secure the hood by tightening the screws

completely.

HD0043

Run power cable to installation location. Place the hood to its location. Mark the position of the screws (smaller part of the key holes)

with a pen. Remove the hood and install the (8) 1/2” double thread screws leaving a 1/8” gap (4 screws for 30” hood). Remove wiring

cover on top of the hood and connect wiring (see instructions included with exterior blower). Place the hood under the cabinet and

slide it in position. Secure the hood by tightening the screws completely.

INTERIOR BLOWER

IN-LINE OR EXTERIOR BLOWER

10

Install screws into the location as shown in the pictures below (P5 or P8 blower). Do not tighten screws down fully, leave a 1/8” gap. Hang

blower unit onto blower plate (screws through the large part of the keyhole). Slide the blower to its position (screws in the small part of the

keyhole). Tighten the screws.

HD0044

Secure the blower by installing 2 more screws into the locations shown in the pictures below (P5 or P8 blower). Reinstall impeller(s) and

cover.

HD0080

13. INSTALL THE BLOWER (P5 AND P8 BLOWERS ONLY)

The blower must be installed to the rough-in plate using four 3/8” screws. Remove the cover from the blower assembly. Remove the

impeller(s) by pulling it (them) out gently (see pictures below).

HD0021

HD0022

P5 BLOWER

HD0081

P8 BLOWER

HD0045

FOR P8 DUAL BLOWER UNIT, ENSURE THE IMPELLERS

ARE CORRECTLY INSTALLED; THE HOOD WILL NOT

WORK PROPERLY IF REVERSED. Both impellers are

different in the dual blower, one rotates clockwise and the other

counterclockwise. Each wheel and motor have an arrow and

a number on them, you have to match them correctly (see

drawing at right).

21

HD0023

FRONT

1

2

HD0023

11

14. INSTALL THE BLOWER (P3, P6, IQ6 AND EXTERIOR BLOWERS ONLY)

Refer to instructions included with blower.

Once the blower is installed, plug the power supply to the 3-prong male connector (A)

and the blower unit into the 2-prong female receptacle (B) inside the hood.

13. INSTALL THE BLOWER (P5 AND P8 BLOWERS ONLY) (CONT'D)

WARNING

!

Never plug the 2-prong blower cord to the 3-prong power supply

cord.

Plug the power supply to the 3-prong male connector (A) and the blower unit into

the 2-prong female receptacle (B) inside the hood.

HE0003

A

B

HE0003

A

B

WARNING

!

Never plug the 2-prong blower cord to the 3-prong power supply

cord.

15. INSTALL THE CALIBRATION BUTTON BRACKET IN THE HOOD

(iQ6 INTERIOR BLOWER ONLY)

The iQ6 blower is equipped with a calibration button already mounted to its own bracket. Install

this bracket in the hood, using 2 screws provided with iQ6 interior blower.

See additional details in the iQ6 blower instructions included with the blower.

HD0007

12

16. REINSTALL BOTTOM PANEL AND HYBRID BAFFLE FILTERS

Reinstall bottom panel using both retaining screws removed in step 5.

Reinstall filters. It is recommended to install side filters first and finish with center one(s).

 Insert the end with filter spring clip of hybrid baffle filter into the upper channel of the hood.

 Raise the other end toward the inside and insert in the grease drip rail of the hood.

Replacement filters are available from your dealer. See label inside hood for part number.

CAUTION

Remove protective plastic film covering filters before installing them.

1

HD0543

2

17. LIGHT BULBS REPLACEMENT

This hood requires 120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base, shielded halogen lamps (included).

1. To remove lamps, gently push upwards and turn counterclockwise to

disengage bulb leads from their grooves.

NOTE: To ease removal of the bulbs, use a rubber dishwashing

glove or use suction cup tool available from Best. Contact

Best Customer Service at 1-800-558-1711 to order suction

cup tool, part no. 99526707.

2. Install the new lamps by placing the bulb leads into their grooves in

the socket.

3. Gently push upwards and turn clockwise until secure.

WARNING

!

Do not touch lamps during or soon after operation. Burns may occur. In order to prevent the risk of personal injury,

only install shielded halogen lamps. Also, never install a cool beam, a dichroïc lamp, a lamp not suitable for use in

recessed luminaires or identified for use in enclosed fixtures.

12 3

HO0089

13

18. USE AND CARE

Hybrid baffle filters and impeller(s)*

The hybrid baffle filters, impeller(s) and grease rail should be cleaned frequently. Use a warm detergent solution. Wash more often if your

cooking style generates greater grease — like frying foods or wok cooking.

Remove filters by pushing filters towards the front of hood and rotating filters downward. Hybrid baffle filters and impeller(s) are dishwasher

safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergent

or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty.

* Impeller(s) only on P5 and P8 blowers.

Hood cleaning

Stainless steel cleaning:

Avoid when choosing a detergent:

- Any cleaners that contain bleach will attack stainless steel.

- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be

used close to a range.

Do:

• Regularly wash with clean cloth or rag soaked with warm water

and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning.

Wipe dry completely.

• You may also use a specialized household stainless steel

cleaner.

Don’t:

• Use any steel or stainless steel wool or any other scrapers to

remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the

hood. During construction/renovation, cover the hood to make

sure no dust sticks to stainless steel surface.

14

19. OPERATION

HEAT SENTRY™

This hood is equipped with a Heat Sentry™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses

excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

!

The HEAT SENTRY can start the blower during a range top fire or other excessive heat situations even if the hood

is turned off. In this case, it is impossible to turn the blower OFF with blower switch. If you must stop the blower,

do it from the main electrical panel.

Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the

air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.

HC0038

1

2

3

HC0039

AB

1) HALOGEN LIGHT KNOB

2) BLOWER SPEED CONTROL KNOB

3) ON/OFF BLOWER SWITCH

A) HALOGEN LIGHT KNOB

B) BLOWER SPEED CONTROL KNOB

COOKTOP LIGHTING (HALOGEN)

A rotary 3-position knob (1) controls the halogen lights (OFF - low intensity - high intensity).

BLOWER

The blower is operated using two controls.

Use the on/off rocker switch (3) to start and stop the blower. When turned on, the blower operates at the previous setting of the speed

control (2).

Turn the speed control knob counterclockwise to increase blower speed – clockwise to decrease speed.

15

20. WIRING DIAGRAMS

INTERIOR BLOWER

120 VAC

GROUND

LINE

NEUTRAL

BLK

G

W

BLK

W

BLK

W

M

INTERNAL BLOWER ASSEMBLY

ROUGH-IN PLATE

W

BLK

W

BLK

BLU BLU

HS

T

HERMOSTAT

FAN SWITCH

BLK

S

PEED CONTROL

LAMP

SWITCH

Y

W

Y

LAMP

W

Y

HE0187A

COLOR CODE

BLK BLACK

BLU BLUE

G GREEN

W WHITE

Y YELLOW

16

20. WIRING DIAGRAMS (CONT'D)

IN-LINE OR EXTERIOR BLOWER

120 VAC

M

REMOTE BLOWER ASSEMBLY

BLU BLU

HE0188A

G

GROUND

LINE

NEUTRAL

COLOR CODE

BLK BLACK

BLU BLUE

G GREEN

W WHITE

Y YELLOW

BLK

G

W

BLK

W

BLK

W

R

OUGH-IN PLATE

W

BLK

W

BLK

HS

T

HERMOSTAT

FAN SWITCH

BLK

S

PEED CONTROL

LAMP

SWITCH

Y

W

Y

W

Y

BLK

W

LAMPLAMP

LAMP

17

21. SERVICE PARTS

Model UP26M

HL0221

2

10

1

3

4

5

6

7

8

9

11

12

13

14

15

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in

good working condition, you must use

Broan-NuTone genuine replacement

parts only. Broan-NuTone genuine

replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety.

Any third party replacement part

used may cause serious damage and

drastically reduce the performance

level of your unit, which will result

in premature failing. Broan-NuTone

recommends to contact a certified

service depot for all replacement

parts and repairs.

KEY

NO.

PART NO.DESCRIPTION

QTY. (HOOD WIDTH)

30" 36" 42" 48"

1 SV05869 BEST LOGO 1111

2

SV61639 HYBRID BAFFLE FILTER 8.84" X 8.61" (INCLUDING HANDLE)-31-

SV61640 HYBRID BAFFLE FILTER 11.84" X 8.61" (INCLUDING HANDLE) 2-23

3

SV61691 F

ILTER FILLER 1.6" (PAIR)-11-

SV61679 FILTER FILLER 3" (PAIR) ---1

4

SV61742 GREASE RAIL 30" 1---

SV61743 GREASE RAIL 36" -1--

SV61744 GREASE RAIL 42" --1-

SV61745 GREASE RAIL 48" ---1

5 SV05917 SOCKET GU10 2233

6 SV09435 SOCKET HOLDER GU10 2233

7 SV09434 LIGHT TRIM, STAINLESS STEEL 2233

8 SV05921 SHIELDED HALOGEN BULBS (50 W, 120 V, PAR16, GU10) 2233

9 SV08578 B

LOWER AND LIGHT KNOBS (2 KNOBS) 1111

10 SV03435 T

HERMOSTAT 1111

11 SV08338 L

IGHT SWITCH 1111

12 SV03501 SPEED CONTROL 1111

13 SV08548 BLOWER ROCKER SWITCH 1111

14 SV13923 FEMALE CONNECTOR 1111

15 SV13924 MALE CONNECTOR 1111

* SV17645 THERMOSTAT BRACKET 1111

* SV21517 INSTALLATION GUIDE 1111

* SV13278

PARTS BAG: 4 LOCK NUTS NO. 10-32, 1 WIRE CLAMP LP16-AP, 2 NO. 6 X 1/2” SCREWS,

2 WIRE CONNECTORS NO. 74B, 6 NO. 8 X 3/8”, 8 DOUBLE THREADED SCREWS 6-12 X 1/2”

1111

* NOT SHOWN.

18

21. SERVICE PARTS (CONT'D)

5

1

2

3

4

5

6

7

8

9

10

11

12

6

13

14

15

16

17

18

19

20

21

22

23

HL0021

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in

good working condition, you must use

Broan-NuTone genuine replacement

parts only. Broan-NuTone genuine

replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety.

Any third party replacement part

used may cause serious damage and

drastically reduce the performance

level of your unit, which will result

in premature failing. Broan-NuTone

recommends to contact a certified

service depot for all replacement

parts and repairs.

KEY NO.PART NO.DESCRIPTION QTY.

1 SV13296 ADAPTER/DAMPER 3¼” X 10” 1

2 SV03500 AIR DEFLECTOR 1

3 SV12997 SINGLE BLOWER ROUGH-IN PLATE ASSEMBLY 1

4 SV03577 FOAM 1/2” X 1/2” X 12” 1

5 SV02160 CAPACITOR 15 µF 1

6*M

ACHINE SCREW NO. 6-32 X 1/4” 4

7 SV01857 W

IRE COVER 1

8*L

OCK NUT NO. 6-32 1

9 SV14973 S

INGLE BLOWER ASSEMBLY 1

10 SV01810 I

MPELLER RING 1

11 SV03400 BLOWER IMPELLER 7.094” X 3.375” CW 1

12 SV01766 MOTOR 165 W CW 1

13 * WASHER 3/16” ID X 3/4” OD 3

14 SV02001 MOTOR GROMMET G-431-1 3

*8” TIE WRAP 2

15 SV11705 M

OTOR MOUNT 1

*WIRE NO. 18 TEW BROWN X 10” 1

16 SV01927 M

ETRIC SCREW M4 X 6 MM PA N QUADREX 4

17 SV03495 S

TRAIN RELIEF FOR BLOWER POWER CORD 1

18 SV03494 36” BLOWER POWER CORD 1

19 SV13230 OUTLET BOX COVER 1

20 SV03496 POWER CORD, 120 VOLTS 1

21 SV00660 STRAIN RELIEF FOR POWER CORD 1

22 * SCREW NO. 8 X 3/8”, T/B, NO. 8 HEAD 2

23 * SCREW NO. 10-32 X 3/8”, TF, GREEN 2

* STANDARD HARDWARE—MAY BE PURCHASED LOCALLY.

SINGLE BLOWER/ROUGH-IN

(Model P5)

19

21. SERVICE PARTS (CONT'D)

1

3

4

5

2

6

7

8

9

10

12

11

HL0022

13

14

18

17

15

16

19

20

22

23

24

25

21

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in

good working condition, you must use

Broan-NuTone genuine replacement

parts only. Broan-NuTone genuine

replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety.

Any third party replacement part

used may cause serious damage and

drastically reduce the performance

level of your unit, which will result

in premature failing. Broan-NuTone

recommends to contact a certified

service depot for all replacement

parts and repairs.

KEY NO.PART NO.DESCRIPTION QTY.

1 SV14971 ADAPTER/DAMPER 3¼” X 14” 1

2 SV13296 A

DAPTER/DAMPER 3¼” X 10” 1

3 SV03500 AIR DEFLECTOR 1

4 SV14975 DUAL BLOWER ROUGH-IN PLATE ASSEMBLY 1

5 SV03577 FOAM 1/2” X 1/2” X 12” 1

6*LOCK NUT NO. 6-32 1

7 SV02160 C

APACITOR 15 µF 2

8 SV01857 W

IRE COVER 2

9 SV01766 MOTOR 165 W CW 1

10 SV03400 BLOWER IMPELLER, HOOD 7.094” X 3.375” CW 1

11 SV14974 DUAL BLOWER ASSEMBLY 1

12 SV01810 I

MPELLER RING 2

13 SV03399 BLOWER IMPELLER, HOOD 7.094” X 3.375” CCW 1

14 SV03457 MOTOR 165 W CCW 1

15 * WASHER 3/16” ID X 3/4” OD 6

*8” TIE WRAP 4

16 SV11705 MOTOR MOUNT 2

*WIRE NO. 18 TEW BROWN X 10” 2

17 SV02001 MOTOR GROMMET G-431-1 6

18 SV01927 M

ETRIC SCREW SCREW M4 X 6 MM PA N QUADREX 8

19 SV03495 S

TRAIN RELIEF FOR BLOWER CORD 1

20 SV03494 36” B

LOWER POWER CORD 1

21 SV14960 OUTLET BOX COVER 1

22 SV03496 POWER CORD, 120 VOLTS 1

23 SV00660 STRAIN RELIEF FOR POWER CORD 1

24 * SCREW NO. 8 X 3/8”, T/B, NO. 8 HEAD 4

25 * SCREW NO. 10-32 X 3/8”, TF, GREEN 2

* STANDARD HARDWARE—MAY BE PURCHASED LOCALLY.

DUAL BLOWER/ROUGH-IN

(Model P8)

20

22. WARRANTY

FIVE-YEAR LIMITED WARRANTY FOR BEST

®

PRODUCTS

Warranty Period and Exclusions: Broan-NuTone, LLC (the “Company”) warrants to the consumer purchaser of its product (“you”) that the product (the

“Product”) will be free from material defects in the materials or its workmanship for a period of five (5) years from the date of original purchase (or such

longer period as may be required by applicable law) or a period of two (2) years from the date of service for any labor provided on the Product.

The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited warranty shall

be the remainder of the original warranty period (or such longer period as may be required by applicable law).

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES AND BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS

AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or

parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than

repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (f) damage caused by

exposure to salt air, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, (j) damage caused by fire, flood or

other act of God, or (k) Products with altered, defaced or removed serial numbers. This warranty covers only Products sold to consumers in North America.

This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.

No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective Products. The foregoing warranties

are exclusive and in lieu of any other warranties and conditions, express or implied. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE

COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES

AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

To the extent that applicable law prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition

is limited to the period specified for the express warranty above. Some jurisdictions (which may include the Province of Quebec or specific US states) do

not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is

for the sole purpose of identifying it and shall not be construed as an express warranty.

Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if any

provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the

remainder of such provision or the other remaining provisions of the Limited Warranty.

Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge,

any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The

Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation

and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part

to the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible for damage in transit. The

Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement

process. Such Products and parts will be comparable in function and performance to an original Product or part and warranted for the remainder of the

original warranty period (or such longer period as may be required by applicable law).

Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product. If the Product or component is no longer

available, replacement may be made with a similar product of equal or greater value, at Company’s sole discretion. This is your sole and exclusive remedy

for breach of this limited warranty.

Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT THE COMPANY’S OPTION,

SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE

COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH

THE PRODUCT, ITS USE OR PERFORMANCE.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction. The disclaimers,

exclusions, and limitations of liability under this warranty will not apply to the extent prohibited by applicable law.

This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of field

service travel and living expenses.

Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver

of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty. The Company will not reimburse you for any expenses

incurred by you in repairing or replacing any defective Product, except for those incurred with the Company’s prior written permission.

How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within

seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product

or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original

written limited warranty, then the terms of the Company’s most current written limited warranty for your particular product will control.

PRODUCT SPECIFICATIONS

All illustrations and specifications in this catalog are based on the latest product information available at time of production. Broan-NuTone, LLC and

BEST® reserves the right to make changes at any time, without notice, in prices, colors, materials, equipment, specifications and models, place of

manufacture and to discontinue models or equipment.

Best

Broan-NuTone, LLC- 926 W. State Street, Hartford, WI 53207 1-800-637-1453

Best®, 550 Lemire Blvd., Drummondville, QC, Canada (1-866-737-7770) www.bestrangehoods.com

La page charge ...

Best UP26M48SB Guide d'installation

Ce manuel convient également à

Best UP26M48SB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents