Crosley CAW9244BW0 Le manuel du propriétaire

Marque: Crosley

Modèle: CAW9244BW0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Top-Loading Washer

Use and Care Guide

Laveuse & chargement par

le dessus guide d'utilisation

et d'entretien

Para una versi6n de estas instrucciones en espa_ol, visite www.whirlpool.com

Table of Contents

WASHER SAFETY ...................................................................... 2

WHAT'S NEW UNDER THE LiD? .............................................. 3

CONTROL PANEL AND FEATURES ......................................... 4

CYCLE GUIDE ............................................................................ 5

USING YOUR WASHER ............................................................. 6

WASHER MAINTENANCE ......................................................... 9

TROUBLESHOOTING .............................................................. 10

WARRANTY .............................................................................. 14

ASSISTANCE OR SERVICE .................................. BACK COVER

Table des mati_res

SECURIT# DE LA LAVEUSE ................................................... 15

QUOI DE NEUF SOUS LE COUVEROLE? .............................. 16

TABLEAU DE COMMANDE ET

CARAOT#RISTIQUES .............................................................. 17

GUIDE DE PROGRAMMES ..................................................... 19

UTILISATION DE LA LAVEUSE ............................................... 20

ENTRETIEN DE LA LAVEUSE ................................................. 23

Di_PANNAGE ............................................................................ 25

GARANTIE ................................................................................ 31

ASSISTANCE OU SERVICE ............... COUVERTURE ARRIERE

W10468394B

W10468395B =SP

Washer Safety

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey aH

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be kifled or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

AHsafety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow cHdren to play on or in the washer. Close

supervision of children is necessary when the washer is used

near cHdren.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach intothe washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where itwill be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

this time.

SAVE THESE iNSTRUCTiONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

What's New Under The Lid?

Your new washer will operate differently than your past agitator-style washer.

@ Lid Lock <] II

To allowforhigherspinspeeds,thelidwilllockand the

LidLocked lightwillturnon.When thislightislit,the

lidislockedand cannotbe opened. When thislightis

blinking,thewasher ispaused. When thislightisoff,the

lidcan be opened. Aftera cycleisstarted,waterwillenter

washer and then lock.Ifyou need to open the lidtoadd

a garment afterthispoint,you must pressSTARTIPAUSE

and waitforthe lidto unlock.The lidwillonlyunlockafter

washer movement has stopped.Depending on when in

thecycleyou tryto pause,itmay takeseveralseconds to

severalminutesforthelidtounlock.PressSTARTIPAUSE

toresume thecycle.

Sounds

Atdifferentstagesofthewash cycle,you may hear

sounds and pauses thataredifferentfromthoseofyour

previouswasher.For example,you may heara clicking

and hum atthe beginningof thecycleas the lidlock

goes througha self-test.There willbe differentkindsof

humming and whirringsounds as the agitatortestsfor

loadbalanceor moves the load.And, sometimes,you

may hearnothingatallas thewasher allowstimefor

clothestosoak.

(_) Sensing 4i:_

This washer will perform a series of spins to check

for load balance. During this time, a series of clicks

and a whirring noise signal that sensing technology

is determining if there is an off-balance load.

Spray Rinse

Select cycles default to a spray rinse. During these cycles,

you will hear water enter the washer as the tub spins,

allowing the rinse water to penetrate clothes. Check the

"Cycle Guide" for details.

IM PORTANI"."

• After the washer basket fills to the selected water level, the lid must be closed before the wash cycle can start.

If filling stops with the lid open, close lid and press START button.

Fabric Softener Added option must be selected to ensure fabric softener dispenses at the correct time.

Control Panel and Features

TEMPERATURE OPTIONS

7 BRIC

_/ARM 2ND RINSE ONE F NSE SOFTFN_R

(__ ADDED

HOT ON[ RINSE 2N

DELICATD

CYCLE STATUS __ O

Not all features and options are available on all models.

Appearance may vary.

O WATER LEVEL

Select the setting most suitable for your load. Small will

add a low amount of water for smaller loads and Max Fill

will add the most amount of water for large or bulky loads.

Items need to move freely. Tightly packing can lead to poor

cleaning performance, and may increase wrinkling and

tangling.

TEMPERATURE

Temperature senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

[] On some models and cycles, warm and hot water may

be cooler than your previous washer.

[] Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

O OPTIONS

The following options may be added to most cycles.

ONE RINSE

This option is used to limit a cycle to one rinse.

2ND RINSE

This option can be used to automatically add a second

rinse to most cycles.

FABRIC SOFTENER ADDED - ONE RINSE

This option must be selected if using fabric softener

during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

FABRIC SOFTENER ADDED - 2ND RINSE

This option turns on both the Fabric Softener and

the 2rid Rinse options.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

See "Cycle Guide" for detailed descriptions of cycles.

START/PAUSE BUTTON

Press to start the selected cycle; press again to pause the

cycle and unlock the lid.

NOTE: If the washer is spinning, it may take several

minutes to unlock the lid. Press and hold for 3 seconds

to cancel a cycle.

CYCLE STATUS LIGHTS

CYCLESTATUS ............

Sensing Wash Rinse Spin Done

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

SENSING

When the START/PAUSE button is pressed, the washer

will fill to the selected water level. If the lid is closed

when the machine is done filling the lid will lock and the

machine will begin operation.

If the lid is open when the water stops entering the

machine, the cycle will not begin until the lid has been

closed and the START/PAUSE button is pressed. If the

cycle has not been started within 10 minutes of the water

filling the washer, the washer will pump out the water.

NOTE: Avoid opening lid during sensing phase. The

sensing process will start over when the washer is

restarted. The sensing light may also come on during the

Soak and Wash portions of the cycle. This is normal. To

restart the washer after the lid has been opened press

start.

WASH

You will hear the agitator moving the load. The motor

sounds may change at different stages in the cycle.

The wash time is determined by the selected soil level.

RINSE

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load. You may hear

the motor turning on briefly (short hum) to move the

basket while filling. Fabric softener will be added if the

Fabric Softener Added option was selected.

Some cycles use spray rinsing. After draining and

spinning out wash water, the washer will continue to

spin and spray in rinse water for the entire rinse time.

SPiN

The washer spins the load at increasing speeds for

proper water removal, based on the selected cycle

and spin speed.

DONE

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

LID LOCKED

To allow for higher spin speeds, the lid

will lock and the Lid Locked light will

turn on. When this light is lit, the lid is

locked and cannot be opened. When

this light is blinking, the washer is

paused. When this light is off, the lid

can be opened.

If you need to open the lid, press

START/PAUSE. The lid will unlock

once the washer movement has

stopped. This may take several

minutes if the load was spinning at

high speed. Press START/PAUSE

again to resume the cycle.

Lid Locked

START

Hold3 se¢

PAUSE tocancel

Cycle Guide

For best fabric care, choose the cycle that best fits the load being washed.

Not all cycles and options are available on all models.

Cottons, linens,

and mixed garment

loads

Cottons, linens,

and mixed garment

loads

Cottons, linens,

and mixed garment

loads

No-iron fabrics,

cottons, perm.

press, linens,

synthetics

No-iron fabrics,

cottons, perm.

press, linens,

synthetics

Machine-wash

silks, hand-washed

fabrics

Sturdy fabrics,

colorfast items,

towels, jeans

Swimsuits and

garments requiring

rinsing without

detergent

Hand-washed

garments or

dripping wet items

Normal Heavy

Normal

Regular

Normal Light

Casual

Regular

Casual Light

Delicate

Super Wash

Rinse &

Spin

Drain &

Spin

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

rinse

N/A

High

Low

High

only High

High

Use this cycle for heavily soiled or sturdy items. This cycle

features a spray rinse. Use this cycle for cleaning the interior

of the washer. See "Washer Care."

Use this cycle for normally soiled cottons and mixed

fabric loads. This cycle features a spray rinse.

Use this cycle for lightly soiled mixed loads. This cycle

features a spray rinse.

Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent

press, and blends.

Use this cycle to wash lightly-soiled loads of no-iron fabrics

such as sport shirts, blouses, casual business clothes,

permanent press, and blends.

Use this cycle to wash lightly soiled garments indicating

"Machine Washable Silks" or "Gentle" cycle on the care

label. Place small items in mesh garment bags before

washing. This cycle features a spray rinse.

Provides maximum wash time and action for tough stains

and soils. Use this cycle for heavily soiled or sturdy items.

Water-level sensing process may take longer for some items

than for others because they will absorb more water than

other fabric types.

Combines a rinse and high-speed spin for loads requiring

an additional rinse cycle or to complete a load after power

interruption. Also use for loads that require rinsing only.

This cycle uses a spin to shorten drying times for heavy

fabrics or special-care items washed by hand. Use this

cycle to drain washer after cancelling a cycle or completing

a cycle after a power failure.

NOTE: If you are using fabric softener, be sure to select one of the Fabric Softener Added options.

*All rinses are cold.

Using Your Washer

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

"1= Sort and prepare your laundry

[] Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing

unexpected sounds.

[] Sort items by recommended cycle, water temperature,

and colorfastness.

[] Separate heavily soiled items from lightly soiled items.

[] Separate delicate items from sturdy fabrics.

[] Do not dry garments if stains remain after washing,

because heat can set stains into fabric.

[] Treat stains promptly.

[] Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

[] Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

[] When washing water-proof or water-resistant items, load

evenly.

[] Use mesh garment bags to help avoid tangling when

washing delicate or small items.

[] Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to

avoid damage to your garments.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Add laundry products

Add a measured of amount of detergent or single-dose

laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric

softener crystals, add to the bottom of the washer basket

before adding clothes.

NOTE: Follow the manufacturer's instructions to determine

the amount of laundry products to use.

3, Load laundry into washer

Load garments in loose heaps evenly

around basket wall. For best results, do

not pack the load tightly. Do not wrap

large items such as sheets around the

agitator; load them in loose piles around

the sides of the basket. Try mixing

different-sized items to reduce tangling.

IMPORTANT: Do not tightly pack or

force items into washer. Items need to

move freely for best cleaning and to

reduce wrinkling and tangling.

Add liquid chlorine bleach

to dispenser

Do not overfill, dilute, or use more than 1 cup (250 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Add fabric softener to dispenser

(on some models}

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer's directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by filling the

dispenser with warm water until liquid reaches

the underside of the rim. See max fill line

arrows.

IMPORTANT: Fabric Softener Added option ........

must be selected to One Rinse or 2nd Rinse

to ensure proper distribution of the fabric

softener during the final rinse portion of

the cycle.

Adding Liquid Fabric Softener Manually to

Wash Load

During the final rinse, wait until the washer has completed

filling, press the START/PAUSE button to pause the washer.

Lift the lid and add the measured recommended amount of

liquid fabric softener. Do not use more than the recommended

amount. Close the lid and press the START/PAUSE button

again to start the washer.

F_, Select cycle

NORMAL

REGULAR

SUPERWASH

DELICATE q

DRAIN & SPIN

CASUAL

REGULAR

LIGHT

RINSE&SPIN

Turn cycle knob to choose your wash cycle. For more

information, see "Cycle Guide."

_', Select WATER LEVEL

WATERLEVEL

LARGE

Select the water level setting most suitable for your load.

Small will add a low amount of water for smaller loads and

Super will add the most amount of water for large or bulky

loads. Items need to move freely.

8, Select TEMPERATURE

TEMPERATURE

All Cold Rinses

Once you select a cycle, select the desired wash temperature

by turning the Wash Temperature knob to the appropriate

setting based on your load. All rinses are tap cold.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

Hot

Some cold water is added to save

energy. This will be cooler than

your hot water heater setting.

Whites and pastels

Durable garments

Warm

Some cold water will be added, so Bright colors

this will be cooler than what your Moderate to light soils

previous washer provided.

Cool

Warm water may be added to Colors that bleed

assist in soil removal and to help or fade

dissolve detergents.

Cold

This is the temperature from your Dark colors that

faucet. If your tap cold water is bleed or fade

very cold, warm water may be Light soils

added to assist in soil removal

and help dissolve detergent.

9. Select options

OPTIONS

Select the desired cycle options. If you are using fabric

softener, be sure to select one of the Fabric Softener Added

options.

Press START/PAUSE to begin wash

cycle

START

Hold3 sec

PAUSE to cancel

Press the START/PAUSE button to start the wash cycle. When

the cycle has finished, the DONE indicator will light. Promptly

remove garments after cycle has completed to avoid odor,

reduce wrinkling, and rusting of metal hooks, zippers, and

snaps.

Unlocking the lid to add garments:

If you need to open the lid to add 1 or 2 missed garments:

Press START/PAUSE; the lid will unlock once the washer

movement has stopped. This may take several minutes if the

load was spinning at high speed. Then close lid and press

START/PAUSE again to restart the cycle.

If lid is left open for more than 10 minutes, the water will pump

out automatically.

Washer Maintenance

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

"installation instructions" for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and

Performing at its Best

1. Always follow the detergent manufacturer's instructions

regarding the amount of detergent to use. Never use more

than the recommended amount because that may increase

the rate at which detergent and soil residue accumulate

inside your washer, which in turn may result in undesirable

odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly cleaning

procedure:

Recommended Cycle for Cleaning the Washer

Refer to the "Cycle Guide" for the optimal cycle for cleaning

the inside of the washer. Use this cycle with affresh ®Washer

Cleaner or liquid chlorine bleach as described below.

Begin procedure

1. afresh ®Washer Cleaner Cycle Procedure (Recommended

for Best Performance):

a. Open the washer lid and remove any clothing or items.

boPlace an afresh ®Washer Cleaner tablet in the bottom of

the washer basket.

coDo not place an affresh ®Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

eoClose the washer lid.

f. Select the cycle recommended for cleaning the inside of

the washer.

goPress the START/Pause button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must be

interrupted, press START/Pause once or twice (depending on

model). After the cycle has stopped, run a RINSE & SPIN cycle

to rinse cleaner from washer.

f WASHER CARE (cont.) "_

2. Chlorine Bleach Procedure {Alternative}:

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach

compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press the START/Pause button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press START/Pause once or twice

(depending on model). After the cycle has stopped, run

a RINSE & SPiN cycle to rinse cleaner from washer.

Cleaning the Dispensers

After a period of using your washer, you may find some residue

buildup in the washer's dispensers. To remove residue from

the dispensers, wipe them with a damp cloth and towel dry.

Do not attempt to remove the dispensers or trim for cleaning.

The dispensers and trim are not removable, ifyour model has

a dispenser drawer, however, remove the drawer and clean

it before or after you run the Clean Washer cycle. Use an all-

purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills.

Use only mild soaps or cleaners when cleaning external

washer surfaces.

IMPORTANT: To avoid damaging the washer's finish, do not

use abrasive products.

NON=USE AND VACATION CARE

Operate your washer only when you are home. If moving, or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid flooding due

to water pressure surge.

f WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

"Winter Storage Care" directions before moving.

3. Disconnect drain from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped until

washer is placed in new location.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

RE! NSTALLING/USI NG WASHER AGAI N

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to "installation Instructions" to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Casual Regular cycle to clean washer

and remove antifreeze, if used. Use half the manufacturer's

recommended amount of detergent for a medium-size load.

Troubleshooting

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

if you experience

Possible Causes Solution

Check the following for Feet may not be in contact with the Front and rear feet must be in firm contact with floor, and

proper installation or floor and locked, washer must be level to operate properly.

see "Using Your

Washer" section. Washer may not be level.

Load could be unbalanced.

Objects caught inwasher drain

system.

Clicking or metallic

noises

Check floor for flexing or sagging. If flooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See "Level the Washer" in Installation Instructions.

Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Normal Regular cycle and Super or Max Fill water level for

oversized, non-absorbent items such as comforters or poly-filled

jackets.

See "Cycle Guide" and "Using Your Washer" in this Use and

Care Guide.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as final amounts of

water are removed during the Drain & Spin cycles.

Troubleshooting

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

If you experience Possible Causes Solution

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Check the following for Washer not level.

proper installation:

Fill hoses not attached tightly.

Fill hose washers.

Drain hose connection.

Check household plumbing for leaks

or clogged sink or drain.

Washer not loaded as

recommended.

Check for proper water supply.

Washer won't run

or fill, washer stops

working or wash light

remains on (indicating

that the washer was

unable to fill

appropriately)

Water may splash off basket if washer is not level. Check that

load is not unbalanced or tightly packed.

Tighten fill-hose connection.

Make sure all four fill hose flat washers are properly seated.

Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets.)

Improper loading can cause basket to be out of alignment

and cause water to splash off tub. See "Using Your Washer"

for loading instructions.

Both hoses must be attached and have water flowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Check proper electrical supply.

Normal washer operation.

Washer may be tightly packed.

Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Remove several items, rearrange load evenly in basket, and add

detergent. Close lid and press START/PAUSE.

Do not add more than 1 or 2 additional items after cycle has

started to avoid tightly packing or unbalancing.

Troubleshooting

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

If you experience Possible Causes Solution

Empty pockets and use garment bags for small items.Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Use a cycle with a low spin speed.

The washer may be tightly packed or

unbalanced.

Washer not draining/

spinning, loads are still

wet, or spin light remains

on (indicating that the

washer was unable to

pump out water within

10 minutes)

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4.5"

(114 mm).

Too much detergent causing suds to

slow or stop draining and spinning.

Dry spots on load High speed spins extract more

after cycle moisture than traditional top-load

washers.

Check for proper water supply.Incorrect or wrong

wash or rinse

temperatures

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed

spin for your garment. To remove extra water in the load, select

Drain & Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See "Using Your Washer" for

loading recommendations.

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the floor. Remove any clogs from drain hose.

Always measure and follow detergent directions for your load. To

remove extra suds, select Rinse & Spin. Do not add detergent.

The high spin speeds combined with airflow during the final spin

can cause items near the top of the load to develop dry spots

during the final spin. This is normal.

Check that hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Load not rinsed

Energy-saving controlled This washer uses cooler wash and rinse water temperatures than

wash temperatures, your previous washer. This includes cooler hot and warm washes.

Check for proper water supply. Check that hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Using too much detergent. The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efficient at rinsing when load is tightly packed.

Using too low a water level selection.

Sand, pet hair, lint, etc. Heavy sand, pet hair, lint, and

on load after washing detergent or bleach residues may

require additional rinsing.

Load is tangling Washer not loaded as recommended.

Washer not loaded as recommended.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Choose a water level that matches the load being washed.

Add a 2nd Rinse to the selected cycle.

See "Using Your Washer" section.

Select a cycle with a slower wash action and spin speed; however,

items will be wetter than those using a higher speed spin. See the

"Cycle Guide" to match your load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

Troubleshooting

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

If you experience

Not cleaning or

removing stains

Incorrect dispenser

operation

Fabric damage

Odors

Lid locked light is

flashing

Single-dose laundry

packet not dissolving

Possible Causes

Washer not loaded as recommended.

Adding detergent on top of load.

Using too low a water level selection.

Using too much detergent.

Solution

Washer is less efficient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only 1 or 2 additional garments after washer has started.

Add detergent, oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Choose a water level that matches the load being washed.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

manufacturer's directions based on load size and soil level.

Not using correct cycle for fabric Use a higher soil level cycle option and warmer wash

type. temperature to improve cleaning.

Use Heavy cycle for tough cleaning. See the "Cycle Guide" to

match your load with the best cycle.

Not using dispensers. Use dispensers to avoid chlorine bleach and fabric softener

staining.

Load dispensers before starting a cycle. Select Fabric Softener

Added option when using fabric softener.

Do not add products directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Clogged dispenser. Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

Sharp items were in pockets during Empty pockets, zip zippers, and snap or hook fasteners before

wash cycle, washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Items may have been damaged Mend rips and broken threads in seams before washing.

before washing.

Fabric damage can occur if load is Load garments in loose heaps evenly around the basket wall.

tightly packed. Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Liquid chlorine bleach may have Do not pour liquid chlorine bleach directly onto load. Wipe up

been added incorrectly, bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Garment care instructions may not Always read and follow garment manufacturer's care label

have been followed, instructions. See the "Cycle Guide" to match your load with the

best cycle.

Monthly maintenance not done as See "Cleaning Your Washer" in "Washer Maintenance."

recommended.

Unload washer as soon as cycle is complete.

Using too much detergent. Be sure to measure correctly. Always follow the manufacturer's

directions.

See "Cleaning your Washer" section.

The lid is not closed. Close the lid. The washer will not start or fill with the lid open.

A cycle was stopped or paused The washer may still be spinning. The lid will not unlock until the

using the Start/Pause button, basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Follow the manufacturer's instructions to avoid damage

to your garments.

CROSLEY ®CORPORATION LAUNDRY WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory

Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance

was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or

Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective

from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DiSCLAiMER OF iMPLiED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABiLiTY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply

to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to

province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMiTATiON OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LiMiTED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR iNCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Crosley <R>dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve

the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by

calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/12

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in=warranty service.

Write clown the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

S6curit de la laveuse

Votre s_curit_ et celle des autres est tr_s importante,

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil m6nager.

Assurez=vous de toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de securit6 vous signale les dangers potentiels de d6ces et de blessures graves

& vous et & d'autres.

Tousles messages de s6curit6 suivront le symboJe d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si

vous ne suivez pas imrn_diatement les instructions.

Risque possible de d6c_s ou de blessure grave

si vous ne suivez pas les instructions,

Tous les messages de s6curit6 vous diront quel est le danger potentieJ et vous disent comment r6duire le risque de

bJessure et ce qui peut se produire en cas de non=respect des instructions.

IMPORTANTES iNSTRUCTIONS DE SECURITE

AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc 61ectrique ou de blessures Iorsde I'utilisation de la

laveuse, suivre les pr6cautions fondamentales dont les suivantes :

[] Lire toutes les instructions avant d'utiliser la laveuse.

[] Ne pas laver des articles qui ont et6 nettoy6s ou

lav6s avec de I'essence ou imbib6s d'essence,

solvants de nettoyage &sec, ou autres substances

inflammables ou explosives; ces substances

peuvent emettre des vapeurs susceptibles de

s'enflammer ou d'exploser.

[] Ne pas ajouter d'essence, solvant de nettoyage &

sec ou autre produit inflammable ou explosif dans

I'eau de lavage. Ces substances peuvent 6mettre

des vapeurs susceptibles de s'enflammer ou

d'exploser.

[] Dans certaines conditions, de I'hydrogene gazeux

peut se former dans un circuit d'eau chaude qui n'a

pas et6 utilise pendant 2 semaines ou plus. LE GAZ

HYDROGENE EST EXPLOSIBLE. Si le circuit d'eau

chaude n'a pas et6 utilise pendant une telle periode,

avant d'utiliser la laveuse, ouvrir tousles robinets

d'eau chaude et laisser I'eau s'ecouler pendant

plusieurs minutes par chaque robinet. Ceci

permettra I'evacuation de I'hydrogene gazeux

accumule. Comme ce gaz est inflammable, ne pas

fumer ou utiliser une fiamme nue au cours de cette

periode.

[] Ne pas laisser des enfants jouer sur ou #.I'interieur de la

laveuse. Bien surveiller les enfants Iorsque la laveuse est

utilisee & proximite d'enfants.

[] Avant de mettre la laveuse au rebut ou hors de service,

enlever la porte ou le couvercle.

[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de

la laveuse Iorsque le tambour, la cuve ou I'agitateur est en

mouvement.

[] Ne pas installer ou remiser cette laveuse & un endroit cO elle

serait exposee aux intemperies.

[] Ne pas modifier les organes de commande.

[] Ne pas reparer ou remplacer un composant quelconque de

la laveuse, ni entreprendre une operation de service, si ce

n'est sp6cifiquement recommand6 dans ce manuel ou dans

un manuel d'instructions de reparations destine &I'utilisateur;

il est alors essentiel que la personne concernee comprenne

ces instructions et soit competente pour les executer.

[] Pour les instructions de liaison & la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

Avertissements de la proposition 65 de I'¢:tat de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour 6tre & I'origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'#tat de Californie pour _tre & I'origine de

malformations et autres deficiences de naissance.

Quoi de neuf sous le couvercle?

Votre nouvelle laveuse fonctionne diff@emment de votre pr6c6dente laveuse de type agitateur.

Verrouillage du couvercle <1111

Pour un essorage a plus haute vitesse, le couvercle

se verrouille et le t6moin de verrouillage du couvercle

s'allume. Lorsque ce t6moin lumineux s'allume, cela

signifie que le couvercle est verrouill6 et ne peut _tre

ouvert. Lorsque ce t6moin lumineux clignote, cela signifie

que la laveuse effectue une pause. Lorsque ce t6moin

lumineux est 6teint, cela signifie qu'on peut ouvrir le

couvercle. Apres le d6marrage d'un programme, de I'eau

p6netre dans la laveuse et celle-ci se verrouille. Si I'on doit

ouvrir le couvercle pour ajouter un v6tement apres cette

6tape, il faut appuyer sur START/PAUSE (mise en marche/

pause) puis attendre que le couvercle se d6verrouille.

Le couvercle se d6verrouille uniquement une fois que le

mouvement de la laveuse a cess6. Selon le moment oQ

I'on souhaite suspendre le programme, le couvercle peut

mettre entre plusieurs secondes voire plusieurs minutes

se d6verrouiller. Appuyer sur START/PAUSE (mise en

marche/pause) pour poursuivre le programme.

Bruits

Au cours de diff@ents stades du programme de lavage,

vous entendrez peut-6tre des bruits et pauses que

votre laveuse pr6c6dente ne produisait pas. II est par

exemple possible que vous entendiez un cliquetis et

un bourdonnement au d6but du programme, Iorsque

le systeme de verrouillage du couvercle effectue un

test automatique. Diff@ents bourdonnements et bruits

de frottements rythmiques se produiront a mesure

que I'agitateur 6value 1'6quilibre de la charge et qu'il la

d6place. IIest aussi possible que la laveuse soit parfois

completement silencieuse, Iorsqu'elle laisse tremper les

v_tements.

@ D_tection "}i:_

La laveuse effectue une s@ie d'essorages pour contr61er

1'6quilibre de la charge. Durant cette p@iode, une s@ie

de cliquetis et un bruit de frottements rythmiques

indiquent que la technologie de d6tection d6termine

si la charge est d6s6quilibr6e.

Ringage par vaporisation

Certains programmes utilisent I'option Ringage par

vaporisation par d6faut. Au cours de ces programmes,

on entend I'eau p6n6trer dans la laveuse tandis que la

cuve tourne, ce qui permet a I'eau de ringage de p6n6trer

les v_tements. Consulter le "Guide de programmes" pour

plus de d6tails.

IMPORTANT :

[] Apres que le panier de la laveuse se soit rempli jusqu'au niveau d'eau s61ectionn6, le couvercle doit 6tre rabattu pour

que le programme de lavage puisse commencer. Si le remplissage s'arr_te alors que le couvercle est ouvert, fermer

le couvercle et appuyer sur le bouton START (mise en marche).

[] Uoption Fabric Softener Added (ajout d'assouplissant pour tissu) doit 6tre s61ectionn6e "oui" pour que I'assouplissant

pour tissu soit distribu6 au moment ad6quat.

Tableau de commande et caract ristiques

..............

Certains programmes et options ne sont pas disponibles sur certains modeles.

L'apparence des appareils peut varier.

O WATER LEVEL (NIVEAU D'EAU)

S61ectionner le r6glage le plus adapt6 & votre charge.

Small (petite) ajoute une faible quantit6 d'eau pour les

charges plus petites et Max Fill (remplissage max) ajoute

la quantit6 d'eau la plus importante pour les grandes

charges ou les charges volumineuses. Les articles doivent

pouvoir se d6placer librement. Trop tasser le linge peut

entrafner une mauvaise performance de lavage et augmenter

le froissement et I'emm_lement.

TEMPERATURE (TEMPI_RATURE}

La fonction de contr61e de temp6rature d6tecte et

maintient une temp6rature uniforme de I'eau en r6gulant

le d6bit d'arriv6e d'eau chaude et d'eau froide.

S61ectionner une temp6rature de lavage en fonction du type

de tissu et de salet6 & laver. Pour des r6sultats optimaux,

suivre les instructions sur 1'6tiquette du v_tement et utiliser

la temp6rature d'eau de lavage la plus chaude possible qui

reste sans danger pour le tissu.

[] Sur certains modeles et programmes, les temp6ratures

de I'eau tiede et de I'eau chaude seront inf6rieures &

celles de votre pr6c6dente laveuse.

[] M_me pour les lavages dont la temp6rature a 6t6 r6gl6e

sur Cool (frais) ou Cold (froid), il est possible que de

I'eau tiede soit ajout6e & la laveuse pour maintenir une

temp6rature minimale.

OPTIONS

II est possible d'ajouter les options suivantes & la plupart

des programmes.

ONE RINSE (UN RIN(_AGE)

On peut utiliser cette option pour limiter le programme

& un rin_age.

2ND RINSE (DEUXIF=ME RIN(_AGE)

On peut utiliser cette option pour ajouter

automatiquement un deuxieme rin(;age & la plupart

des programmes.

FABRIC SOFTENER ADDED - ONE RINSE

(AJOUT D'ASSOUPLISSANT POUR TISSU AVEC

UN RIN(_AGE}

Cette option doit _tre s61ectionn6e si I'on utilise de

I'assouplissant pour tissu durant un programme. Ceci

garantit que I'assouplissant pour tissu est ajout6 au bon

moment Iors du ringage pour _tre correctement distribu&

FABRIC SOFTENER ADDED - 2ND RINSE

(AJOUT D'ASSOUPLISSANT POUR TISSU AVEC

UN DEUXIEME RIN(_AGE)

Cette option active les options Fabric Softener

(assouplissant pour tissu) et 2nd Rinse (deuxieme

rin£:age).

BOUTON DE PROGRAMME DE LAVAGE

Utiliser le bouton du programme de lavage pour s61ectionner

les programmes disponibles sur la laveuse. Voir "Guide

de programmes" pour des descriptions de programmes

d6taill6es.

BOUTON START/PAUSE

(MISE EN MARCHE/PAUSE)

Appuyer sur ce bouton pour d6marrer le programme

s61ectionn_, puis appuyer de nouveau pour suspendre

le programme et d6verrouiller le couvercle.

REIVIARQUE : Si la laveuse tourne, le couvercle peut

mettre quelques minutes & se d6verrouiller. Appuyer

pendant 3 secondes pour annuler un programme.

O CYCLE STATUS LIGHTS

(TEMOINS LUMINEUX DES

PROGRAMMES)

CYCLESTATUS ...................... 0

Sensing Wash Rinse Spin Done Lid Locked

Les t6moins lumineux indiquent la progression du

programme. ,_chaque 6tape du processus, il est possible

que I'on remarque des pauses ou des sons diff@ents de

ceux des laveuses ordinaires.

SENSING (Di_TECTION)

Lorsqu'on appuie sur le bouton START/PAUSE/

Unlock Lid (mise en marche/pause/d6verrouillage

couvercle), la laveuse se remplit jusqu'au niveau

d'eau s61ectionn& Si le couvercle est ferm6 Iorsque la

machine a fini de se remplir, le couvercle se verrouille

et la machine commence & fonctionner.

Si le couvercle est ouvert alors que I'eau cesse d'entrer

dans la machine, le programme ne d6marre pas tant

que I'on n'a pas ferm6 le couvercle et que I'on n'a

pas appuy6 sur le bouton START/PAUSE/Unlock Lid

(mise en marche/pause/d6verrouillage couvercle). Si

le programme n'a pas commenc6 dans les 10 minutes

qui suivent le remplissage de la laveuse, la laveuse

commence a pomper I'eau pour 1'6vacuer.

REMARQUE : Ftviter d'ouvrir le couvercle durant le

processus de d6tection. Le processus de d6tection

recommencera une fois la laveuse remise en marche.

Le t6moin de d6tection s'allume 6galement Iors des

6tapes de trempage et de lavage du programme. Ceci

est normal. Pour remettre la laveuse en marche apres

que le couvercle a 6t6 ouvert, appuyer sur START

(mise en marche).

WASH (LAVAG E}

On entend I'impulseur d6placer la charge. Les

bruits 6mis par le moteur peuvent changer Iors des

diff@entes 6tapes du programme. La dur6e de lavage

est d6termin6e par le niveau de salet6 s61ectionn&

RINSE (RIN(_AGE)

On entend des sons similaires b,ceux entendu Iors du

programme de lavage & mesure que la laveuse rince

et d6place la charge. On peut entendre le moteur se

mettre en marche brievement (court bourdonnement)

pour faire bouger le panier Iors du remplissage.

L'assouplissant pour tissu sera ajout6 si I'option Fabric

Softener Added (ajout d'assouplissant pour tissu) a

6t6 s61ectionn6e.

Certains programmes utilisent un rin_age avec

vaporisation. Apres avoir effectu6 la vidange et

I'extraction de I"eau, la laveuse poursuit I'essorage

et la vaporisation d'eau de rinoage pendant toute

la dur6e de rinoage.

SPIN (ESSORAGE}

La laveuse essore la charge & des vitesses

augmentant graduellement pour une bonne extraction

de I'eau, en fonction du programme et de la vitesse

d'essorage s61ectionn6s.

DONE (TERMINle)

Une fois le programme termin6, ce t6moin s'allume.

Retirer la charge rapidement pour un r6sultat optimal.

LID LOCKED (VERROUILLAGE DU

COUVERCLE)

Pour un essorage & plus haute vitesse, O

Lid Locked

le couvercle se verrouille et le t6moin

de verrouillage du couvercle s'allume.

Lorsque ce t6moin lumineux s'allume,

cela signifie que le couvercle est verrouill6 et ne peut

6tre ouvert. Lorsque ce t6moin lumineux clignote, cela

signifie que la laveuse effectue une pause. Lorsque

ce t6moin lumineux est 6teint, cela signifie qu'on peut

ouvrir le couvercle.

Si I'on doit ouvrir le couvercle, appuyer

sur START/PAUSE (mise en marche/

pause). Le couvercle se d6verrouille

une fois que le mouvement de la

laveuse a cess& II se peut que cela

prenne plusieurs minutes si la laveuse

essorait la charge b.grande vitesse.

Appuyer de nouveau sur START/PAUSE

(mise en marche/pause) pour suivre

le programme.

START

HoUd3sec

PAUSE tocancel

Guide de programmes

Pour un meilleur soin des tissus, choisir le programme qui convient le mieux & la charge & laver.

Certains programmes et options ne sont pas disponibles sur certains modeles.

Articles en coton,

linge de maison et

charges mixtes

Articles en coton,

linge de maison et

charges mixtes

Articles en coton,

linge de maison et

charges mixtes

Articles non

repassables,

articles en coton, de

pressage permanent,

linge de maison,

tissus synthetiques

Articles non

repassables,

articles en coton, de

pressage permanent,

linge de maison,

tissus synthetiques

Articles en soie

lavables en machine,

articles laves

la main

Tissus resistants,

articles grand-teint,

serviettes, jeans

MaJllotset articles

necessitant un

ringage sans

detergent

Articles tres humides

et articles laves

la main

Normal

(normal)

Heavy (intense)

Normal

(normal)

Regular

(regulier)

Normal

(normal)

Light (leger)

Casual

(Tout-after)

Regular

(regulier)

Casual

(Tout-after)

Light (leger)

Delicate

(Articles delicat)

Super Wash

(super lavage)

Rinse & Spin

(Ringage et

essorage)

Drain & Spin

(Vidange et

essorage)

Hot (Chaudei

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Hot (Chaude)

Warm (Tiede)

Cool (Frafche)

Cold (Froide)

Ringage & I'eau

froide uniquement

N/A

High (Elevee)

Low (Basse)

High (Elevee)

Utiliser ce programme pour les articles tres sales ou

robustes. Ce programme comporte un ringage par

vaporisation. UtilJserce programme pour nettoyer I'interieur

de la laveuse. Voir "EntretJen de la laveuse".

UtilJser ce programme pour les articles en coton et

les charges de tissus mixtes presentant un degre de

salete normal. Ce programme comporte un ringage

par vaporisation.

Utiliser ce programme pour laver des charges mixtes de

v_tements peu sales. Ce programme comporte un ringage

par vaporisation.

Utiliser ce programme pour laver des charges de

v_tements quJne se repassent pastels que chemises de

sport, chemisiers, v_tements de travail tout-aller, articles

pressage permanent et melanges de tJssus.

Utiliser ce programme pour laver des charges peu sales

de v_tements non repassables tels que chemises de

sport, chemisiers, v_tements de travail tout-aller, articles

pressage permanent et melanges de tJssus.

Utiliser ce programme pour laver des v_tements

legerement sales dont I'etiquette de soin indique "Soie

lavable en machine" ou "Programme delicat". Placer les

petits articles dans des sacs en filet avant le lavage. Ce

programme comporte un ringage par vaporisatJon.

Utilise le temps de lavage maximal et Faction la plus

intense pour eliminer les taches et saletes les plus difficiles.

UtilJser ce programme pour les articles tres sales ou

robustes. Le processus de detection du niveau d'eau peut

ne pas prendre le m_me temps pour tousles articles car

certains tJssus absorbent plus d'eau que d'autres.

Combine un ringage et un essorage rapide pour

les charges necessitant un programme de ringage

supplementaire ou pour finir de prendre soin d'une charge

apres une coupure de courant. Utiliser egalement pour les

charges necessitant uniquement un ringage.

Ce programme utJliseun essorage pour reduire les durees

de sechage pour les tissus Iourds et les articles laves & la

main necessitant un soJnspecial. Utiliser ce programme

pour vJdanger la laveuse apres avoir annule un programme

ou avoJrtermine un programme apres une coupure de

courant.

REMARQUE : Si I'on utilise de I'assouplissant pour tissu, veiller & s_lectionner I'une des options Fabric Softener Added (ajout d'assouplissant

pour tissu).

*Tousles ringagesse font & I'eau froide.

Utilisation de ia iaveuse

Risque d'incendie

Ne jamais rnettre des articles humect_s d'essence ou

d'autres fluides inflammables darts la laveuse.

Aucune laveuse ne peut compl_ternent enlever I'huile.

Ne pas faire s_cher des articles qui ont _t_ sails par

tout genre d'huile (y compris les huiles de cuisson).

Le non=respect de ces instructions peut causer un

d_c_s, une explosion ou un incendie.

"1= Trier et preparer le linge

[] Vider les poches. Des pieces de monnaie, des boutons

ou objets de petite taille sont susceptibles de glisser sous

I'impulseur et de s'y coincer, ce qui peut entraTne des

bruits inattendus.

[] Trier les articles en fonction du programme et de la

temp6rature d'eau recommand6s, ainsi que de la solidit6

des teintures.

[] S6parer les articles tr_s sales des articles peu sales.

[] S6parer les articles d61icats des tissus r6sistants.

[] Ne pas s6cher les v_tements si les taches sont toujours

pr6sentes apr_s le lavage car la chaleur pourrait fixer

les taches sur le tissu.

[] Traiter les taches sans d61ai.

[] Fermer les fermetures & glissiere, attacher les crochets,

cordons et ceintures en tissu. Oter les garnitures et les

ornements non lavables.

[] R6parer les d6chirures pour 6viter que les articles

ne s'endommagent encore davantage lots du lavage.

Conseils utiles :

[] Lors du lavage d'articles imperm6ables ou r6sistants

I'eau, charger la laveuse de fagon uniforme.

[] Utiliser des sacs en filet pour aider a emp_cher

I'emm_lement lots du lavage d'articles d61icats ou de

petits articles.

[] Retourner les tricots pour 6viter le boulochage. S6parer

les articles qui forment la charpie de ceux qui la

retiennent. Les articles synth6tiques, tricots et articles

en velours retiennent la charpie provenant des serviettes,

des tapis et des tissus chenille.

REMARQUE : Toujours life et suivre les instructions des

6tiquettes de soin des tissus pour 6viter d'endommager

les v_tements.

Risque de choc _lectrique

Brancher sur une prise & 3 alv_oles reii_e & la terre.

Ne pas enlever la broche de liaison _ la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c_ble de rallonge.

Le non=respect de ces instructions peut causer

un d_c_s, un incendie ou un choc dlectrique.

Ajouter les produits de lessive

Verser une mesure de d6tergent ou un sachet de lessive

dose unique dans le panier.

Si I'on utilise des produits activateurs de d6tergent de type

Oxi, un agent de blanchiment sans danger pour les couleurs

ou de I'assouplissant pour tissu sous forme de cristaux, les

ajouter au fond du panier de la laveuse avant d'ajouter les

v_tements.

REIVlARQUE : Suivre les instructions du fabricant pour

d6terminer la quantit6 de produits de lessive a utiliser.

La page charge ...

Crosley CAW9244BW0 Le manuel du propriétaire

Marque: Crosley

Modèle: CAW9244BW0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Crosley CAW9244BW0 Owner's manual