Hilti SCW Mode d'emploi

Marque: Hilti

Modèle: SCW

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

SCW 22-A

English 1

Français 15

Español 30

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

SCW 22-A

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Mode d'emploi original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶

Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols

The following symbols can be used on the product:

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

2 English 2153714

*2153714*

Rated speed under no load

Direct current (DC)

Revolutions per minute

Diameter

Saw blade

Wireless data transfer

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Circular saw SCW 22A

Generation 01

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration issued by the certification department can be found at the end of

this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 3

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

4 English 2153714

*2153714*

▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Safety instructions for all saws

Cutting procedures

▶

DANGER: Keep hands away from cutting area and the blade. Keep your second hand on

auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

▶ Do not reach underneath the workpiece. The guard cannot protect you from the blade below the

workpiece.

▶ Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

▶ Never hold the workpiece in your hands or across your leg while cutting. Secure the workpiece

to a stable platform. It is important to support the work properly to minimise body exposure, blade

binding, or loss of control.

▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts

of the power tool "live" and could give the operator an electric shock.

▶ When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and

reduces the chance of blade binding.

▶ Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw will run off-centre, causing loss of control.

▶ Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and safety of operation.

Kickback causes and related warnings

• kickback is a sudden reaction to a pinched, jammed or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the operator;

• when the blade is pinched or jammed tightly by the kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the operator;

• if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided

by taking proper precautions as given below.

▶ Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces.

Position your body to either side of the blade, but not in line with the blade. Kickback could cause

the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions

are taken.

▶ When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the

saw motionless in the material until the blade comes to a complete stop. Never attempt to remove

the saw from the work or pull the saw backward while the blade is in motion or kickback may

occur. Investigate and take corrective actions to eliminate the cause of blade binding.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 5

▶ When restarting a saw in the workpiece, centre the saw blade in the kerf so that the saw teeth are

not engaged into the material. If a saw blade binds, it may walk up or kickback from the workpiece as

the saw is restarted.

▶ Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed under the panel on both sides, near the line of cut and

near the edge of the panel.

▶ Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf

causing excessive friction, blade binding and kickback.

▶ Blade depth and bevel adjusting locking levers must be tight and secure before making the cut. If

blade adjustment shifts while cutting, it may cause binding and kickback.

▶ Use extra caution when sawing into existing walls or other blind areas. The protruding blade may

cut objects that can cause kickback.

Lower guard function

▶ Check the lower guard for proper closing before each use. Do not operate the saw if the lower

guard does not move freely and close instantly. Never clamp or tie the lower guard into the open

position. If the saw is accidentally dropped, the lower guard may be bent. Raise the lower guard with

the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all

angles and depths of cut.

▶ Check the operation of the guard return spring. If the guard and the spring are not operating

properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged

parts, gummy deposits, or a build-up of debris.

▶ The lower guard may be retracted manually only for special cuts such as "plunge cuts" and

"compound cuts". Raise the lower guard by the retracting handle and as soon as the blade enters

the material, the lower guard must be released. For all other sawing, the lower guard should operate

automatically.

▶ Always observe that the lower guard is covering the blade before placing the saw down on bench

or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to stop after switch is released.

2.3 Additional safety instructions

Personal safety

▶ Modification of the power tool is not permitted.

▶ Always hold the machine with both hands on the grips provided. Keep the grips dry, clean and free

from oil and grease.

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Respiratory protection must be worn if the power tool is used without a dust removal system for

work that creates dust.

▶ Operate the tool only together with the safety devices that belong to it.

▶ Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers

during breaks between working.

▶ The power tool is not intended for use by inexperienced persons who have received no special

training.

▶ Keep the power tool out of reach of children.

▶ Do not switch the product on before it is at the workplace.

▶ Remove the battery before storing or transporting the power tool.

▶

Do not work overhead with the product.

▶ Do not attempt to brake the product by applying lateral pressure to the saw blade.

▶ The kerf must be free of obstructions. Do not saw into screws and nails etc.

▶ Do not touch the clamping flange or the clamping screw while the power tool is running.

▶ Never press the drive spindle lock button while the saw blade is rotating.

▶ Never direct the power tool toward persons.

▶ Adjust the pressure applied to the saw blade and the material being cut so that the blade does not

stall, possibly causing kickback.

▶ Avoid overheating the tips of the saw blade teeth.

▶ When cutting plastic, melting of the plastic should be avoided.

▶ Dust from materials, such as paint containing lead, some wood species, concrete / masonry / stone

containing silica, and minerals as well as metal, may be harmful. Contact with or inhalation of the dust

may cause allergic reactions and/or respiratory or other diseases to the operator or bystanders. Certain

kinds of dust are classified as carcinogenic such as oak and beech dust, especially in conjunction with

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

6 English 2153714

*2153714*

additives for wood conditioning (chromate, wood preservative). Material containing asbestos may be

handled only by specialists. Use a dust removal system whenever possible. To achieve a high level

of dust collection, use a suitable vacuum cleaner. When indicated, wear a respirator appropriate

for the type of dust generated. Ensure that the workplace is well ventilated. Follow national

requirements for the materials you want to work with.

▶ Before beginning the work, check the hazard classification of the dust that will be produced. Use

an industrial vacuum cleaner with an officially approved protection classification in compliance

with locally applicable dust protection regulations.

▶ Observe the national health and safety requirements.

Electrical safety

▶ Before beginning work, check the working area (e.g. using a metal detector) to ensure that no

concealed electric cables or gas and water pipes are present. External metal parts of the power tool

may become live, for example, when an electric cable is damaged accidentally. This presents a serious

risk of electric shock.

Careful handling and use of batteries

▶ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

▶ Do not expose batteries to high temperatures and keep them away from fire. There is a risk of

explosion.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over

80°C (176°F). This presents a risk of fire, explosion or injury through contact with caustic substances.

▶ Never continue to use or attempt to charge damaged batteries, e.g. batteries with cracks, broken

parts, bent or pushed-in / pulled-out contacts).

▶ Do not use the battery as a power source for other unspecified power tools or appliances.

▶ If the battery is too hot to touch it may be defective. In this case, place the power tool in a non-

flammable location, well away from flammable materials, where the battery can be kept under

observation and allowed to cool down. Contact Hilti Service after the battery has cooled down.

2.4 Additional safety instructions for circular saws

▶ Bring the saw blade into contact with the workpiece only when the circular saw is switched on.

➥ The path of the saw must be free of obstructions above and below the workpiece. Do not saw into

screws, nails or similar objects.

▶ Never work overhead with a circular saw.

▶ Never attempt to brake the saw blade by applying lateral pressure.

▶ Avoid overheating the tips of the saw blade teeth.

▶ Always use a saw blade that this suitable for the material you are going to saw.

2.5 Battery use and care

▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion

batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable

location, well away from flammable materials, where it can be kept under observation and allowed to

cool down. In this case, always contact your Hilti Service.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 7

3 Description

3.1 Overview of the product 1

Auxiliary grip

;

Switch-on interlock release button

On/off switch

Grip

Guard

(

Release buttons with additional function

(charge status display activation)

)

Hose connector (chip deflector)

Pivoting guard operating lever

Arbor

Base plate

Pivoting guard

∙

Fence

Direction-of-rotation arrow

Clamping lever for cutting angle adjustment

Cutting angle scale

Charge state and fault display

Battery

Clamping lever for cutting depth adjustment

Hex key

Cutting depth scale

Spindle lock button

Clamping screw for fence

45° cutting line indicator

0° cutting line indicator

Mounting flange

Clamping flange

Clamping screw

3.2 Intended use

The product described is a cordless circular saw. It is designed for sawing wood or wood-like materials,

plastics, drywall panel, gypsum fiber board and composite materials.

The circular saw is equipped with a removable connector for an optional vacuum cleaner / dust removal

hose. This connector is designed to fit standard suction hoses. In order to connect the vacuum cleaner hose

to the saw, use of a suitable adapter may be necessary.

▶ The use of saw blades not in compliance with the given specification (e.g. diameter, speed of rotation,

thickness) or the use of cutting and grinding discs or blades made from high-alloy steel (HSS steel) is not

permissible. Sawing metals is not permissible.

▶ Do not use the product to cut tree branches or trunks.

▶ Use only Hilti Liion batteries from the B 18 / B 22 series with this product.

▶ Use only Hilti battery chargers of the C4/36 series with these batteries.

3.3 Liion battery display

The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on

the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery

release buttons.

Status Meaning

4 LEDs light. Charge status: 75 % to 100 %

3 LEDs light. Charge status: 50 % to 75 %

2 LEDs light. Charge status: 25 % to 50 %

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

8 English 2153714

*2153714*

Status Meaning

1 LED lights. Charge status: 10 % to 25 %

1 LED blinks, the power tool is ready for use. Charge status: < 10 %

1 LED blinks, the power tool is not ready for use. The battery has overheated or is completely dis-

charged.

4 LEDs blink, the power tool is not ready for use. The power tool is overloaded or has overheated.

Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch.

If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.

3.4 Fence

Use of the single arm fence allows precise cuts to be made along the edge of the workpiece, or strips of

even width to be cut.

The fence can be fitted on either side of the base plate.

3.5 Items supplied

Circular saw, saw blade, hex key, fence, vacuum cleaner hose connector, operating instructions.

Spare parts, consumables and accessories approved by Hilti for use with the product can be found at

your local Hilti Store or online at: www.hilti.group | USA: www.hilti.com

3.6 Accessories

Clamping flange, mounting flange, clamping screw.

4 Technical data

4.1 Circular saw

SCW 22-A

Rated voltage

21.6 V

Weight

9.0 lb

(4.1 kg)

Specified blade diameter

6.3 in … 6.5 in

(160 mm … 165 mm)

Blade disc thickness

0.02 in … 0.06 in

(0.5 mm … 1.5 mm)

Kerf width

0.06 in … 0.1 in

(1.5 mm … 2 mm)

Saw blade arbor size

0.8 in

(20 mm)

Rated speed under no load

4,000 /min

Maximum cutting depth

2.2 in

(57 mm)

Bevel cutting angle

0° … 50°

Operating temperature

1 ℉ … 140 ℉

(−17 ℃ … 60 ℃)

Storage temperature range (without battery)

−4 ℉ … 158 ℉

(−20 ℃ … 70 ℃)

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 9

4.2 Battery

Battery operating voltage

21.6 V

Ambient temperature for operation

1 ℉ … 140 ℉

(−17 ℃ … 60 ℃)

Storage temperature

−4 ℉ … 104 ℉

(−20 ℃ … 40 ℃)

Battery charging starting temperature

14 ℉ … 113 ℉

(−10 ℃ … 45 ℃)

5 Operation

5.1 Preparations at the workplace

5.1.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery.

5.1.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible click.

3. Check that the battery is seated securely.

5.1.3 Removing the battery

1. Press the release buttons on the battery.

2. Pull the battery out of its holder in the device.

5.1.4 Removing the saw blade 2

WARNING

Risk of burning injury. A hot accessory tool, clamping flange or clamping screw and the sharp edges of the

saw blade present hazards.

▶ Wear protective gloves when changing saw blades.

1. Pull the battery out of the product to the rear.

2. Insert the hex key into the saw blade clamping screw.

3. Press the spindle lock button and hold it in this position.

4. Turn the saw blade clamping screw with the hex key until the spindle lock button engages fully.

5. Release the clamping screw by turning the hex key in the direction of the direction-of-rotation arrow.

6. Remove the clamping screw from the outer clamping flange.

7. Open the pivoting guard by swinging it to the side and then remove the saw blade.

If necessary, the mounting flange can be removed for cleaning.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

10 English 2153714

*2153714*

5.1.5 Fitting the saw blade 3

CAUTION

Risk of damage! Unsuitable or incorrectly fitted saw blades may damage the saw.

▶ Only use blades which are suitable for this saw. Observe the direction-of-rotation arrow on the saw

blade.

▶ Use only saw blades equipped with a rated maximum permissible speed that is at least as high as the

maximum speed stated on the product.

Check that the blade to be fitted complies with the technical requirements and that it is well

sharpened. A sharp saw blade is an essential requirement for a perfect cut.

1. Pull the battery out of the product to the rear.

2. Clean the mounting flange and the clamping flange.

3. Fit the mounting flange onto the drive spindle the right way round.

4. Open the pivoting guard.

5. Fit the new saw blade.

6. Fit the outer clamping flange the right way round.

7. Insert the hex key into the saw blade clamping screw.

8. Press the drive spindle lock button.

9. Secure the clamping flange with the clamping screw by turning the hex key in the direction opposite to

the direction-of-rotation arrow.

➥ The spindle lock button engages.

10. Before using the power tool, check that the saw blade is correctly seated and tightened securely.

5.1.6 Adjusting the cutting depth 4

1. Pull the battery out of the product to the rear.

2. Release the cutting depth adjustment clamping lever.

3. Lift the product in a scissor movement and set the desired cutting depth by closing the clamping lever.

The cutting depth should always be set to a depth approx. 5 to 10 mm greater than the thickness

of the material to be cut.

5.1.7 Setting the cutting angle 5

1. Pull the battery out of the product to the rear.

2. Release the cutting angle adjustment clamping lever.

3. Pivot the product into the desired position.

4. Tighten the cutting angle adjustment clamping lever.

5.1.8 Sawing along a line 6

Secure the workpiece to prevent movement.

Position the workpiece so that the saw blade is free to rotate beneath it.

Check to ensure that the on/off switch on the product is in the “off” position.

Position the forward section of the saw’s base plate on the workpiece but do not bring the blade into

contact with the workpiece.

1. Fit the battery into the product.

2. While pressing the safety lock, switch the product on by pressing the on/off button.

3. Guide the product along the cutting line on the workpiece at a suitable speed.

5.1.9 Installing / adjusting the fence 7

1. Pull the battery out of the product to the rear.

2. Screw the clamping screw into the base plate, leaving enough space to slide the fence through.

3. Slide the fence guide under the clamping screw.

4. Set the desired cutting width.

5. Tighten the clamping screw.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 11

5.1.10 Fitting the guide rail adapter 8

The saw can be equipped with a guide rail adapter which is available as an accessory.

1. Remove the battery.

2. Remove the fence, if one is fitted.

3. Fit the base plate into the side retaining channels of the guide rail adapter.

4. Fully insert the base plate into the guide rail adapter.

5. Lock the guide rail adapter by pressing in the two sliders as far as they will go.

5.2 Work

5.2.1 Switching on

▶ While pressing the safety lock, switch the product on by pressing the on/off button.

5.2.2 Switching off

▶ Release the on/off switch to stop the machine.

5.2.3 Longitudinal cuts at 0°

1. Place the saw on the guide rail so that the rib fits into the groove in the adapter.

2. Switch the product on. → page 11

3. Guide the product along the rail and through the workpiece at a suitable speed.

5.2.4 Longitudinal cuts at angles up to 50°

1. Set the angle.

2. Switch the product on. → page 11

3. Guide the saw along the guide rail with the outer edge of the guide rail adapter on the rib on the guide

rail. The saw blade will otherwise collide with the guide rail.

5.2.5 Making cuts at an angle across the surface of the workpiece

1. Position the guide rail with the zero mark at the edge of the workpiece and then pivot the rail until the

desired angle shown on the angle scale is opposite the zero mark. The cutting angle indicated is the

angle of deviation from a straight, right-angled cut.

2. Secure the guide rail with the two screw clamps.

3. Switch the product on. → page 11

4. Guide the product along the rail and through the workpiece at a suitable speed.

5.2.6 Using the saw without a dust and chip removal system

1. Check that the sawdust is ejected without obstruction.

2. If required, the hose connector can be removed from the blade guard by slackening the hex socket screw

with the hex key supplied with the product.

5.3 Procedure if the chip / dust channel is blocked

1. Pull the battery out of the product to the rear.

2. Clean the chip / dust channel.

Remove the saw blade if necessary.

3. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may

affect operation of the product.

6 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance tasks!

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

12 English 2153714

*2153714*

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

6.1 Cleaning the safety guard

1. Remove the saw blade before cleaning the safety guard parts.

2. Clean the safety guard parts carefully with a dry brush.

3. Use a suitable tool to remove deposits or cuttings from the inside surfaces of the safety guard parts.

4. Fit the saw blade.

6.2 Checks after cleaning and maintenance

After cleaning or maintenance, check that all safety devices are fitted and that they function faultlessly.

▶ To check the pivoting guard, open the guard fully by moving the guard operating lever.

➥ The pivoting guard must close quickly and completely when the guard operating lever is released.

7 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized

persons.

▶ Check the tool and batteries for damage before use after long periods of storage.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

*2153714*

2153714 English 13

8 Troubleshooting

▶ If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

8.1 The circular saw is not in working order.

Malfunction Possible cause Action to be taken

The LEDs indicate nothing. The battery is not fully inserted. ▶ Insert the battery.

The battery is discharged. ▶ Charge the battery.

The battery is too hot or too cold. ▶ Bring the battery to the correct

ambient temperature.

1 LED blinks. The battery is discharged. ▶ Charge the battery.

The battery is too hot or too cold. ▶ Bring the battery to the correct

ambient temperature.

4 LEDs blink. The circular saw was overloaded

briefly.

▶ Release the control switch and

then press it again.

The overheating prevention cut-out

has been activated.

▶ Allow the circular saw to cool

down to cool down and clean

the air vents.

8.2 The circular saw is in working order.

Trouble or fault Possible cause Action to be taken

The on/off button cannot be

pressed, i.e. the button is

locked.

Not a fault (safety function). ▶ Press the safety lock.

Running speed suddenly

drops considerably.

The battery is discharged. ▶ Charge the battery.

Saw advance pressure is too high. ▶ Reduce advance pressure and

switch the product back on.

The battery runs down more

quickly than usual.

Battery condition is not optimal. ▶ Replace the battery.

The product doesn’t restart

by itself after the saw blade

has stalled.

The overload cut-out has been

activated.

▶ Press the switch-on interlock

and the on/off button again.

The battery does not en-

gage with an audible "double

click".

The retaining lugs on the battery

are dirty.

▶ Clean the retaining lugs and refit

the battery.

The circular saw or battery

gets very hot.

Electrical fault. ▶ Switch off the circular saw

immediately. Remove the

battery and keep it under

observation. Allow the battery

to cool down. Contact Hilti

service.

The product is overloaded (appli-

cation limits exceeded).

▶ Select a tool that is suitable for

its intended use.

No suction power or reduced

suction power

The chip ejector channel is

blocked.

▶ Clean the chip / dust channel.

→ page 11

9 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking gases or fluids.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

14 English 2153714

*2153714*

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

10 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

Printed: 24.05.2019 | Doc-Nr: PUB / 5292960 / 000 / 01

La page est en cours de chargement...

Hilti SCW Mode d'emploi

Marque: Hilti

Modèle: SCW

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Hilti SCW Operating instructions
español: Hilti SCW Instrucciones de operación

Hilti SCW Mode d'emploi

Hilti SCW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents