L'Or Barista LM8012/05 Manuel utilisateur

English 7

Dansk 27

Deutsch 46

Español 66

Français 86

Italiano 106

Nederlands 126

Norsk 146

Português 165

Svenska 185

English

7

English

Machine overview

1 On/off button

2 Ristretto button

3 Espresso button

4 Lungo button

5 Water tank lid

6 Water tank

7 Milk frother lid

8 Whisk holder

9 Whisk

10 On/off button of milk frother

11 Base of milk frother

12 Mains cord with plug

13 Used capsule drawer

14 Waste water drawer

15 Lower drip tray

16 Drip tray

17 Cup platform

18 Coffee outlet

19 Coffee dispensing spout cap

20 Capsule compartment

21 Lever

Introduction

Welcome to the L'OR Barista world! The L'OR Barista coffee system is the only

capsule coffee system that allows you to brew two cups of coffee at the same

time thanks to a coffee dispensing spout with double outlet.

The new and exclusive L'OR Barista double-shot coffee capsules allow you to

brew two cups of coffee or a double shot of coffee.

The L'OR Barista coffee machine is also compatible with the L'OR Espresso single-

shot coffee capsules. Thanks to the Dual Capsule Recognition technology, the

machine automatically recognizes the capsule size and adapts the volume

accordingly. All you need to do is press the button for the type of coffee you

desire.

This model of the L'OR Barista coffee machine has an integrated milk frother to

brew coffee with fresh, frothed milk.

Capsule compatibility

The L'OR Barista coffee machine has been designed to work with L’OR Espresso

single-shot capsules and L’OR Barista double-shot capsules, as well as with

Nespresso* capsules and aluminum capsules from coffee brands produced by

Jacobs Douwe Egberts, such as Douwe Egberts, JACOBS, Jacqmotte, Jacques

Vabre, Grand Mère, L'OR, Marcilla, Moccona, Saimaza and Senseo.

*brand of a third party not connected to JACOBS DOUWE EGBERTS and / or

PHILIPS

8English

Preparing for use

Before first use, remove all packaging materials from the machine.

When you use the machine for the first time or if you have not used it for 1 day

or longer, perform the following steps:

1Remove the water tank from the machine.

2Rinse and fill the water tank under the tap. Place the water tank back onto

the machine.

3Place a bowl under the coffee dispensing spout. Do not insert a capsule and

make sure that the lever is closed.

4Press the on/off button to switch on the machine.

-The on/off button flashes slowly to indicate that the machine is heating

up.

9

English

5When all buttons light up continuously, press the lungo button.

-Water flows from the coffee dispensing spout.

Note: When the internal water circuit is empty, the machine produces a

humming sound. When the machine dispenses water, it produces a less loud

humming sound. This is normal.

6The machine is ready when all buttons light up continuously.

7Empty the drip tray and waste water drawer (see 'Cleaning the used capsule

drawer and waste water drawer').

The machine is now ready for use.

Brewing coffee

Beverages and capsules

Capsules

L’OR aluminum capsules are available online at www.lorespresso.com and in

shops. You can choose from a variety of coffee capsules for different types of

coffee.

Beverages

Thanks to the Dual Capsule Recognition technology, the machine automatically

recognizes the capsule size and adapts the volume of your drink accordingly. All

you need to do is press the button for the type of coffee you desire.

10 English

Preparing coffee

1Press the on/off button to switch on the machine. The on/off button starts

flashing to indicate that the machine is heating up.

11

English

2For one coffee, place one cup under the coffee spout.

3For two coffees, place two cups under the coffee spout.

4For a large coffee or Grand Café Filtre, remove the cup platform and the drip

tray, place the cup platform on the lower drip tray and place a large cup or

mug on the cup platform under the coffee spout.

5Lift the lever.

6Insert a capsule.

-For a single cup of coffee, insert a L'OR Espresso single-shot capsule.

12 English

-For two cups of coffee or one large coffee, insert a L'OR Barista double-

shot capsule.

7Close the lever by pushing it down.

Make sure the lid is closed properly and the lid lever is locked

before you start brewing.

8When the on/off button stops flashing and all buttons light up continuously,

press the button for the type of coffee you desire.

9Do not lift the lever until the brewing process has finished. Brewing is finished

when the lights stop flashing and no more coffee comes out of the coffee

outlets.

Brewing Grand Café Filtre

1Remove the seal completely from the capsule.

2Lift the lever and insert the capsule.

13

English

3Close the lever.

4Remove the drip tray with the cup platform. Put the drip tray aside and place

the cup platform on the lower drip tray.

5Place a large cup or mug on the cup platform under the coffee dispensing

spout.

6Press the lungo button to start the brewing process.

Drink personalization

With drink personalization, you can program your drink volume. Each coffee

button on the machine has been programmed to brew coffee at its ideal setting.

Nevertheless, you can adapt the coffee volume to your wishes, within a range

that ensures the best coffee quality.

14 English

The coffee volumes for L'OR Espresso single-shot and L'OR Barista double-shot

capsules are adjusted separately:

1Press the on/off button to switch on the machine.

2Fill the water tank.

3Insert a capsule and close the lever.

-If you want to adjust the volume for L'OR single-shot espresso capsules,

insert a normal L'OR Espresso capsule.

-If you want to adjust the volume for a L'OR Barista double-shot capsule,

insert a L'OR Barista capsule.

4Press and hold the button of the coffee whose volume you want to adjust for

3 seconds until the button flashes quickly. Then release the button. The

machine starts brewing coffee.

5Press the same button again when the cup contains the desired volume.

Note: If you press the coffee button too early, the machine programs the

minimum volume of coffee shown in the table above. If you do not press the

coffee button, the machine programs the maximum volume of coffee.

Resetting the coffee quantities

To reset the coffee quantities to their factory settings:

1Press the on/off button to switch on the machine.

2Wait until the machine has heated up and all buttons light up.

3Press and hold the ristretto, espresso and lungo buttons simultaneously until

all buttons flash quickly to show that the machine has been reset to factory

settings.

15

English

Preparing milk

1Remove the milk frother lid with the whisk holder attached from the milk

frother.

2Fill the milk frother with milk to the desired level. Do not fill beyond the MAX

level.

3Place the milk frother lid with whisk holder back onto the milk frother.

4Press the button for 1 second to heat and froth the milk. The light in the

on/off button comes on.

Note: Press the button for 3 seconds for cold frothed milk.

5The milk froth is ready when the light in the on/off light goes off. You can

now remove the milk frother lid with the whisk holder attached from the milk

frother. Pour the frothed milk onto the freshly brewed coffee.

16 English

Cleaning and maintenance

Cleaning the used capsule drawer and waste water drawer

Check the used capsule drawer and waste water drawer regularly.

Note: For optimal hygiene, pull up the lever after use to ensure the last used

capsule falls into used capsule drawer.

1Pull the used capsule drawer and the waste water drawer out of the machine.

2Remove the drip tray from the lower drip tray and rinse the drip tray and the

cup tray under a warm tap. Do not clean these parts in the dishwasher.

3Remove the used capsule drawer by pulling it up and empty it.

Caution: Be careful when you remove the used capsule drawer. Capsules

are still hot immediately after brewing.

4Rinse all parts under a warm tap. Dry all parts with a soft cloth. You can also

clean all these parts in the dishwasher.

5Reinsert the used capsule drawer into the waste water drawer.

6Insert the waste water drawer with the used capsule drawer into the

machine.

7Place the drip tray back onto the lower drip tray. Place the cup platform onto

the drip tray.

17

English

Cleaning other parts of the machine

1Clean the outside of the machine with a soft damp cloth.

Caution: Never use scouring pads, abrasive cleaning agents or

aggressive liquids such as petrol or acetone to clean the machine.

Warning: Do not insert a finger into the capsule compartment to

avoid injury. There is an invisible piercer inside.

2Clean the front of the machine with a soft damp cloth and clean the two

parts of the coffee dispensing spout (the coffee outlet and the spout cover)

under a warm tap or in the dishwasher.

3Clean the water tank by rinsing it under a warm tap. The water tank is not

dishwasher-proof.

Note: Rinse the water tank and fill it with fresh water every 24 hours.

Cleaning the coffee circuit

Clean the coffee circuit every week to ensure you get coffee with an optimum

quality and taste.

1Place a cup under the coffee dispensing spout.

2Lift the lever to ensure the last used capsule falls into the used capsule

drawer.

3Do not insert a new capsule and close the lever.

18 English

4Press the lungo button.

5Empty the cup after the machine has finished dispensing water.

6Open the lever and repeat steps 3 to 5 to ensure proper cleaning of the

coffee circuit.

The machine is now ready for use.

Cleaning the milk frother

1Remove the milk frother from its base.

2Remove the milk frother lid with the whisk holder attached from the milk

frother.

3Rinse the inside of the milk frother under hot running water.

4Clean the outside of the milk frother with a moist cloth.

5Remove the whisk holder from the milk frother lid.

6Remove the whisk from the whisk holder.

7Rinse the milk frother lid and the whisk holder parts under hot running water.

Note: The lid and the whisk holder parts can also be cleaned in the

dishwasher.

19

English

8Reattach the whisk to the whisk holder.

9Reattach the shaft of the whisk holder to the milk frother lid.

10 Place the milk frother lid with whisk holder back into the milk frother.

Descaling

When to descale

-Descale the machine when the ristretto and lungo button flash quickly a few

times after brewing. The descaling procedure takes up to 40 minutes and

consists of a descaling cycle and a rinsing cycle. Do not interrupt the descaling

procedure.

Why to descale

Descaling is essential for the following reasons:

-It prolongs the life of your L'OR Barista coffee machine

-It ensures maximum cup volume

-It ensures maximum coffee temperature

20 English

-The machine produces less sound during brewing

-It prevents malfunctioning

If the descaling procedure is not performed correctly, scale residue remains

behind in the machine. This causes scale to build up more quickly and may cause

permanent and irreparable damage to the machine.

Use the correct descaler

Only lactic acid-based descalers are suitable for descaling the L'OR Barista

machine. This type of descaler descales the machine without damaging it. We

advise you to use the dedicated L'OR Barista liquid descaler (CA6530) or Saeco

liquid descaler (CA6700). It is available in bottles that contain liquid descaler for

two descaling procedures. You need half a bottle for one descaling procedure

and can store the other half for the next descaling procedure.

Descaling procedure

Note: If something goes wrong during the descaling procedure, e.g. because you

accidentally interrupt the descaling cycle, you have to restart the descaling

procedure from step 1.

1Press the on/off button to switch on the machine.

2Pour half a bottle of L'OR Barista liquid descaler (CA6530) into the water tank.

3Fill up the water tank with fresh tap water.

4Make sure that there is no capsule in the capsule compartment.

21

English

5Close the lever.

6Place a bowl with a minimum capacity of 1.5 liters on the lower drip tray

under the coffee dispensing spout to collect the descaling solution.

7Press the ristretto and lungo button briefly at the same time.

8The ristretto button starts to flash quickly. Press the ristretto button to

activate the descaling cycle.The machine dispenses the entire descaling

solution at regular intervals. This takes up to 30 minutes.

-When the lungo button starts to flash quickly again, the first phase of the

descaling cycle has finished.

9Remove and empty the bowl. Place the bowl back onto the lower drip tray

under the coffee dispensing spout.

10 Remove the water tank and rinse it under the tap. Fill the water tank with

cold tap water and place it back onto the machine.

22 English

11 Press the lungo button to start the flushing cycle.

Note: The water tank will be emptied without interruption. The flushing cycle

lasts about 3 minutes.

12 When the flushing cycle has finished, the ristretto and lungo button flash a

few times.

Note: It is normal that some water remains behind in the water tank after the

descaling procedure.

The machine switches off. The descaling procedure is finished.

Meaning of light signals

-The on/off button flashes slowly: the machine is heating up.

-The on/off button flashes quickly: the water tank is empty, fill the water tank

with tap water.

-All buttons light up continuously: the machine is ready for use.

-The selected coffee button flashes slowly: the machine is preparing the coffee

recipe.

-The selected coffee button flashes quickly:

-Programming is activated.

-The new coffee volume is saved.

-The ristretto and lungo button flash simultaneously after brewing coffee: you

need to descale the machine.

Troubleshooting

This chapter summarizes the most common problems you could encounter with

your machine. If you are unable to solve the problem with the information

below, visit www.lorbarista.com/support for a list of frequently asked questions

or contact the Consumer Care Center in your country.

Troubleshooting coffee machine

Problem Possible cause Solution

The machine does not switch

on.

The machine is not connected to the

mains.

Put the plug in an earthed wall

socket.

The on/off button is flashing

slowly.

The machine is heating up. This is normal.

23

English

Problem Possible cause Solution

The brewing time is longer than

before.

The machine is clogging up with

scale.

Descale the machine.

The temperature of freshly

brewed coffee gradually

decreases.

The machine is clogging up with

scale.

Descale the machine.

The pump makes a lot of noise. There is not enough water in the

water tank.

Fill the water tank with fresh tap

water.

The water tank is not placed

correctly.

Place the water tank correctly and

push it downwards.

The machine suddenly stops

brewing coffee.

There is not enough water in the

water tank.

Fill the water tank with fresh tap

water. Press the button of the

selected type of coffee again to

continue brewing. When the cup is

full, press the same button again to

stop the brewing process.

The on/off button flashes

quickly.

The water tank is empty. Fill the water tank with fresh tap

water. Press the button of the

selected type of coffee again to

continue brewing. When the cup is

full, press the same button again to

stop the brewing process.

I cannot close the capsule

compartment lever completely.

Check if you use the recommended

L'OR capsule. Other capsules may

cause problems during use..

The used capsule drawer is full. Empty the used capsule drawer

and insert the capsule again.

The capsule is not inserted correctly. Insert the capsule again and check

if it is inserted correctly.

The capsule is stuck. Open and close the lever a few

times with moderate force to

remove the capsule.

The lever does not open

completely.

The used capsule drawer is full. Empty the used capsule drawer.

The machine does not dispense

coffee or only dispenses drops

of coffee.

You have not flushed the machine

before first use.

Flush the machine before first use

(see 'Preparing for use').

There is not enough water in the

water tank.

Fill the water tank with fresh tap

water.

Scale has built up inside the machine

(see 'Descaling').

Descale the machine (see

'Descaling').

La page charge ...

L'Or Barista LM8012/05 Manuel utilisateur

L'Or Barista LM8012/05 Manuel utilisateur

dans d''autres langues