Astria Fireplaces POLARIS Instruction Sheet

Marque: Astria Fireplaces

Modèle: POLARIS

Catégorie: Cheminées

Taper: Instruction Sheet

Ce manuel convient également à

VRE4300

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

IN CANADA: THE CONVERSION SHALL BE CAR-

RIED OUT IN ACCORDANCE WITH THE REQUIRE-

MENTS OF THE PROVINCIAL AUTHORITIES

HAVING JURISDICTION AND IN ACCORDANCE

WITH THE REQUIREMENTS OF THE CAN/CSA

B149.1 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE

CONFORMÉMENT AUX RECOMMANDA-

TIONS DES AUTORITÉS PROVINCIALES

AYANT JURIDICTION ET CONFORMÉMENT

AUX EXIGENCES DU CODE D'INSTALLATION

CAN/CSA B149.1.

Gas conversion kits are available to adapt your

appliance from the use of one type of gas to the

use of another. These kits contain all the neces-

sary components needed to complete the task

including labeling that must be afﬁxed to ensure

safe operation.

Kit part numbers are listed here and the following

steps detail the conversion procedure.

CAUTION: THE GAS SUPPLY SHALL BE SHUT

OFF PRIOR TO DISCONNECTING THE ELECTRI-

CAL POWER, BEFORE PROCEEDING WITH THE

CONVERSION.

Step 1. Turn off the gas supply to the appliance

and disconnect the electrical power.

Step 2. Carefully remove the logs. Exercise care

so as not to break the logs. Remove any lava

rock within the burner pan.

Step 3. Remove the burner tube with attached

venturi tube. Refer to Figure 1 for the location

of the control valve and regulator, main oriﬁce

and pilot.

Access

Cover

Control Valve

And Regulator

Pilot Orifice Burner Tube

Main

Orifice

Figure 1

Gas Conversion Kits

Models Conversion

Type

Catalog No.

(Model)

Polaris36/42

VRE4336/42

E36/42ODG

Propane (LP)

Natural Gas

H4915

(GCK-DB166N)

Polaris36/42

VRE4336/42

E36/42ODG

Natural Gas

Propane (LP)

H4916

(GCK-DB089P)

INSTALLATION INSTRUCTIONS FOR GAS CONVERSION KITS FOR USE WITH OUTDOOR GAS FIREPLACES

[MODELS POLARIS36/42, VRE4336/42 AND E36/42ODG SERIES ELECTRONIC OUTDOOR FIREPLACES]

DEXEN ELECTRONIC

GAS CONVERSION KITS

P/N 750222M

Rev. C, 03/2020

HEARTH PRODUCTS

KITS AND ACCESSORIES

WARNING

This conversion kit shall be installed by a qualiﬁed

service agency in accordance with the manufacturer's

instructions and all applicable codes and requirements

of the authority having jurisdiction. If the information

in these instructions is not followed exactly, a ﬁre,

explosion or production of carbon monoxide may result

causing property damage, personal injury or loss of life.

The qualiﬁed service agency performing this installation

is responsible for the proper installation of this kit and

assumes responsibility for this conversion. The instal-

lation is not proper and complete until the operation of

the converted appliance is checked as speciﬁed in the

manufacturers instructions supplied with the kit. The

qualiﬁed service agency performing this installation

assumes responsibility for this conversion.

AVERTISSEMENT

Cet équipement de conversion sera installé par

une agence qualiﬁée de service conformément aux

instructions du fabricant et toutes exigences et codes

applicables de l'autorisés avoir la juridiction. Si

l'information dans cette instruction n'est pas suivie

exactement, un feu, explosion ou production de

protoxyde de carbone peut résulter le dommages

causer de propriété, perte ou blessure personnelle de

vie. L'agence qualiﬁée de service est esponsable de

l'installation propre de cet équipment. L'installation

n'est pas propre et compléte jusqu'à l'opération de

l'appareil converti est chéque suivant les critères

établis dans les instructions de propriétaire provi-

sionnées avec l'équipement.

Figure 6

Step 8. Turn on gas supply and test for gas

leaks, using a soapy water solution.

Step 7. Attach appropriate conversion kit label

(Figure 6 ) to the rating plate on the appliance.

P/N 750222M REV. C 03/2020

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 3

Figure 2

Figure 4

Note: If the ignitor is damaged, a replacement kit

is available, order Catalog Number 87L54.

Step 6. Reassemble the remaining components

by reversing the procedures outlined in the

preceding steps.

Pilot Stage

Terminal Pressure-Tap

(Inlet) Pilot Gas

Outlet

Supply Gas

Inlet

Pressure-Tap

(Manifold)

Burner Stage

Terminal

Ground

(TP)

PILOT

OUT

VENT

Gas Outlet

To Burner

Regulator

Mounting Screw

Figure 5

Electronic Appliances

Step 4. Dexen Electronic Valves - See Figure

2 and the instructions provided with the kit.

Remove and discard the two pressure regula-

tor mounting screws. Remove the pressure

regulator and diaphragm. Discard all removed

components. Ensure the provided diaphragm

is installed properly onto the replacement

pressure regulator and install the new pressure

regulator using the new screws supplied with

the kit. Tighten screws.

See Figure 3 and replace the pilot oriﬁce as

follows: Remove pilot hood assembly to

access the pilot oriﬁce. Remove and replace

the oriﬁce with the one provided with the kit.

Exercise extreme care to prevent damage to

or breakage of the ignitor assembly.

Step 5. (Refer to Figure 5 )

A. Remove the oriﬁce from the manifold and

replace it with the one provided in the kit. See the

following table for oriﬁce sizes for natural and pro-

pane models. Figure 4 illustrates the oriﬁce.

B. Retrieve the burner and slide the venturi

tube over the oriﬁce. Set the shutter adjusting

opening as shown in Figure 5.

Remove Tube

Regulator

Orifice

Remove Clip

Shutter

Opening

RENRUBNIAM

GNITTESGNINEPORETTUHSYROTCAF

sledoM saGlarutaN

)mm(sehcni

saGenaporP

)mm(sehcni

llA

sledoM 61/1)85.1

7.21(

.oNledoM

ezisecifirO

larutaNenaporP

sledoMllA 82#

5041.0

74#

5870.0

Use pipe joint compound or Teﬂon tape on all

pipe ﬁttings before installing (ensure propane

resistant compounds are used in propane ap-

plications, do not use pipe joint compounds

on ﬂare ﬁttings).

THIS APPLIANCE HAS BEEN CONVERTED TO:

NATURAL GAS

INPUT BTU/HR – 50,000

MANIFOLD PRESSURE – 3.5"

ORIFICE SIZE – (0.130)

THIS APPLIANCE HAS BEEN CONVERTED TO:

PROPANE/LPG

INPUT BTU/HR – 50,000

MANIFOLD PRESSURE – 10"

ORIFICE SIZE – (0.080)

ELECTRONIC PILOT

Pilot

Hood

Sensor

Ignitor

PROPANE NATURAL

Innovative Hearth Products (IHP) reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and also to discontinue colors, styles and products.

Consult your local distributor for ﬁreplace code information.

Astria Fireplaces POLARIS Instruction Sheet

Marque: Astria Fireplaces

Modèle: POLARIS

Catégorie: Cheminées

Taper: Instruction Sheet

Ce manuel convient également à

VRE4300

Télécharger le PDF

rapport

dans d''autres langues

English: Astria Fireplaces POLARIS

Astria Fireplaces POLARIS Instruction Sheet

Ce manuel convient également à

Astria Fireplaces POLARIS Instruction Sheet

dans d''autres langues

Autres documents