Lithonia Lighting TCC Commercial Steel Exit Combo Guide d'installation

Marque: Lithonia Lighting

Modèle: TCC Commercial Steel Exit Combo

Taper: Guide d'installation

Ce manuel convient également à

TCC Commercial Steel Running Man Combo

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE

INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from ﬁre, electric

shock, falling parts, cuts/abrasions, and other hazards please read all warnings

and instructions included with and on the ﬁxture box and all ﬁxture labels.

• Before installing, servicing, or performing routine maintenance upon this

equipment, follow these general precautions.

• Installation and service of luminaires should be performed by a qualified

licensed electrician.

• Maintenance of the luminaires should be performed by person(s) familiar

with the luminaires’ construction and operation and any hazards involved.

Regular ﬁxture maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens.

Frequency of cleaning will depend on ambient dirt level and minimum light

output which is acceptable to user. Refractor/lens should be washed in a

solution of warm water and any mild, non-abrasive household detergent,

rinsed with clean water and wiped dry. Should optical assembly become

dirty on the inside, wipe refractor/lens and clean in above manner, replacing

damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly

packed so that no parts should have been damaged during transit. Inspect to

conﬁrm. Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please

visit www.epa.gov.

• These instructions do not purport to cover all details or variations in

equipment nor to provide every possible contingency to meet in connection

with installation, operation, or maintenance. Should further information

be desired or should particular problems arise which are not covered

sufﬁciently for the purchaser’s or owner’s purposes, this matter should be

referred to Acuity Brands Lighting, Inc.

• Disconnect or turn off power before installation or servicing.

• Verify that supply voltage is correct by comparing it with the luminaire label

information.

• Make all electrical and grounded connections in accordance with the

National Electrical Code (NEC) and any applicable local code requirements.

• All wiring connections should be capped with UL approved recognized wire

connectors.

• Wear gloves and safety glasses at all times when removing luminaire from

carton, installing, servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

• Allow lamp/ﬁxture to cool before handling. Do not touch enclosure or light source.

• Do not exceed maximum wattage marked on luminaire label.

• Follow all manufacturer’s warnings, recommendations and restrictions for: driver

type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.

• Do not operate in close proximity to persons, combustible materials or

substances affected by heat or drying.

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.

• Do not mount or support these ﬁxtures in a manner that can cut the outer

jacket or damage wire insulation.

• Unless individual product speciﬁcations deem otherwise: Never connect an LED

product to dimmer packs, occupancy sensors, timing devices, or other related

control devices. LED ﬁxtures must be powered directly off a switched circuit.

• Unless individual product speciﬁcations deem otherwise: Do not restrict

ﬁxture ventilation. Allow for some volume of airspace around ﬁxture. Avoid

covering LED ﬁxtures with insulation, foam, or other material that will

prevent convection or conduction cooling.

• Unless individual product speciﬁcations deem otherwise: Do not exceed

ﬁxtures maximum ambient temperature.

• Only use ﬁxture in its intended location.

• LED products are Polarity Sensitive. Ensure proper Polarity before installation.

• Electrostatic Discharge (ESD): ESD can damage LED ﬁxtures. Personal

grounding equipment must be worn during all installation or servicing of the unit.

• Do not touch individual electrical components as this can cause ESD,

shorten lamp life, or alter performance.

• Some components inside the ﬁxture may not be serviceable. In the unlikely

event your unit may require service, stop using the unit immediately and

contact an ABL representative for assistance.

• Always read the ﬁxtures complete installation instructions prior to installation

for any additional ﬁxture speciﬁc warnings.

• Verify that power distribution system has proper grounding. Lack of proper

earth ground can lead to ﬁxture failure and may void warranty.

All luminaires that contain electronic devices that generate frequencies

above 9kHz from any component within the luminaire comply with

Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference (2) This

device must accept any interference received, including interference that

may cause undesired operation.

Failure to follow any of these instructions could void product warranties.

For a complete listing of product Terms and Conditions, please visit

www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no

responsibility for claims arising out of improper or careless installation or

handling of its products.

ABL LED General Warnings, Form No. 503.203

LEA Y RESPETE TODAS LAS INSTRUCCIONES DE INSTALACIÓN

GUARDE LAS INSTRUCCIONES Y DEVUÉLVALAS AL PROPIETARIO

DESPUÉS DE REALIZAR LA INSTALACIÓN

• Para reducir el riesgo de muerte, lesiones personales o daño a la propiedad que

pueda surgir de incendios, choques eléctricos, cortes, abrasiones, caída de

partes y otros peligros lea todas las advertencias e instrucciones incluidas en

la caja o su interior, además de las etiquetas del montaje.

• Antes de instalar, revisar o realizar el mantenimiento de rutina del equipo, siga

estas precauciones generales.

• La instalación y el mantenimiento de las luminarias lo debe realizar un electri-

cista calificado autorizado.

• El mantenimiento de las luminarias lo debe realizar una persona familiarizada con la

fabricación y el funcionamiento de este producto así como con los peligros relacio-

nados con este. Se recomienda realizar el mantenimiento regular de los montajes.

• Cada tanto será necesario limpiar la parte externa del refractor y de la lente. La

frecuencia de la limpieza dependerá del nivel de polvo del ambiente y de la potencia

de la luz mínima aceptable para el usuario. El refractor/la lente se debe lavar con una

solución de agua tibia y detergente de uso doméstico suave no abrasivo, enjuagar con

agua limpia y secar. Si el montaje óptico se ensuciara por dentro, limpie el refractor o la

lente como se indicó anteriormente; de ser necesario, reemplace las juntas dañadas.

• NO INSTALE EL PRODUCTO SI ESTÁ DAÑADO Esta luminaria se embaló

adecuadamente de modo tal que las piezas no resulten dañadas durante su

transporte. Inspecciónelas para conﬁrmarlo. Reemplace toda pieza que se

dañe o rompa durante su montaje o posterior a este.

• Reciclado: Para obtener información sobre cómo reciclar productos electrónic-

os LED, visite www.epa.gov.

• Estas instrucciones no pretenden cubrir todos los detalles o las variaciones de

los equipos ni abarcar todas las posibles eventualidades relacionadas con la

instalación, el funcionamiento o el mantenimiento. Si necesita más información

o surgen problemas especíﬁ cos que no están debidamente cubiertos en la

información del producto, remítase a Acuity Brands Lighting, Inc.

• Desconecte o interrumpa la energía eléctrica antes de realizar la instalación o

la reparación.

• Veriﬁ que el voltaje de alimentación sea correcto; compárelo con la información

de la etiqueta de la luminaria.

• Realice todas las conexiones eléctricas y a tierra en cumplimiento con el

Código Eléctrico Nacional y de los requisitos del código local vigente.

• Todas las conexiones de cableado deben cubrirse con conectores para cable

reconocidos y aprobados por UL.

• Use gafas y guantes de protección en todo momento al retirar la luminaria de la

caja, al instalarla, repararla o realizar operaciones de mantenimiento.

• Una vez encendida la fuente de luz, evite la exposición directa con los ojos.

ADVERTENCIA: RIESGO DE QUEMADURAS

• Antes de manipular la lámpara o el montaje, déjelo enfriar. No toque la carcasa

ni la fuente de iluminación.

• No supere el voltaje máximo señalado en la etiqueta de la luminaria.

• Respete todas las advertencias, recomendaciones y restricciones que propor-

ciona el fabricante para: tipo de conductor, posición de funcionamiento, puntos

o métodos de montaje, reemplazo y reciclado.

PRECAUCIÓN: RIESGO DE INCENDIO

• Mantenga lejos de la luminaria y de las lámparas o los lentes, los materiales

combustibles y de otro tipo que se puedan incendiar.

• No las encienda cerca de personas, materiales combustibles o sustancias

calientes o secas.

• Jamás conecte componentes bajo carga.

• No monte estos montajes de manera que puedan cortar el revestimiento

exterior o dañar el aislamiento de los cables.

• A menos que las especiﬁ caciones del producto individual consideren lo

contrario: Jamás conecte un producto LED directamente a un paquete de

reducción de intensidad de la luz, sensores de ocupación, dispositivos de

sincronización u otros dispositivos de control relacionados. Los montajes LED

se deben apagar directamente de un circuito de interruptores.

• A menos que las especiﬁ caciones del producto individual consideren lo

contrario: No restrinja la ventilación de las luminarias. Deje un poco de espacio

alrededor del montaje. Evite cubrir los montajes LED con aislación, goma u otro

material que evitará la convección o el enfriamiento de la conducción.

• A menos que las especiﬁ caciones del producto individual consideren lo con-

trario: No exceda la temperatura ambiente máxima de las luminarias.

• Use la luminaria únicamente en el lugar previsto.

• Los productos LED son sensibles a la polaridad. Asegure la correcta polaridad

antes de la instalación.

• Descarga electrostática (DES): la DES puede dañar los montajes LED. Durante la

instalación o reparación de la unidad se debe usar siempre equipo personal

conectado a tierra.

• No toque componentes eléctricos individuales ya que esto puede causar DES,

reducir la vida útil de la lámpara o alterar el funcionamiento.

• Es posible que algunos componentes dentro del montaje no se puedan reparar. En

el caso improbable de que su unidad requiera reparación, deje de usar la unidad

inmediatamente y comuníquese con un representante de ABL para obtener ayuda.

• Lea siempre las instrucciones completas de instalación de montaje antes de la

instalación para veriﬁcar si hay advertencias especíﬁcas de montaje adicionales.

• Veriﬁque que el sistema de distribución de alimentación tenga una conexión a

tierra adecuada. La falta de una toma de tierra adecuada puede conducir a una

falla de la luminaria y puede anular la garantía.

Todas las luminarias que contienen dispositivos eléctricos que

generan frecuencias superiores a 9 kHz desde cualquier componente

de la luminaria cumplen con la Parte 15 de las reglas de la FCC. El

funcionamiento está sujeto a las siguientes dos condiciones: (1) este

dispositivo no puede ocasionar interferencias perjudiciales, y (2) este

dispositivo debe aceptar cualquier interferencia recibida, incluso

aquellas que pueden ocasionar un mal funcionamiento.

El incumplimiento de alguna de estas instrucciones puede anular la garantía

del producto. Para obtener la lista completa de los términos y las condiciones

respecto del producto, visite www.acuitybrands.com. Acuity Brands Lighting,

Inc. no se hace responsable por los reclamos que puedan surgir de la

instalación o manipulación inadecuada o negligente de sus productos.

Advertencias generales de ABL LED, Form. no. 503.203

LIRE ATTENTIVEMENT ET OBSERVER TOUTES LES CONSIGNES DE

SÉCURITÉ CONSERVER CES DIRECTIVES ET LES REMETTRE AU

PROPRIÉTAIRE APRÈS L’INSTALLATION

• Pour réduire les risques de décès, blessures ou dommages matériels résultant

d’un incendie, d’un choc électrique, de chutes de pièces, coupures, érafl ures et

autres dangers, veuillez lire tous les avertissements et toutes les directives fournis

avec l’appareil, sur la boîte et les étiquettes.

• Avant l’installation, l’entretien ou la maintenance de cet équipement, veuillez

prendre les précautions générales suivantes.

• L’installation et le service technique des luminaires doivent être effectués par un

électricien licencié qualifié.

• L’entretien des luminaires doit être effectué par des personnes au courant de la

construction et du fonctionnement des luminaires et des risques impliqués. Un

programme d’entretien régulier est recommandé.

• À l’occasion, il sera nécessaire de nettoyer l’extérieur du réfracteur ou de la lentille.

La fréquence de nettoyage dépendra du niveau de saleté ambiant et du fl ux

lumineux minimal acceptable pour l’utilisateur. Le réfracteur et la lentille doivent être

nettoyés à l’aide d’une solution d’eau tempérée et de tout détergent domestique

doux, non abrasif, puis rincés à l’eau propre et essuyés. En cas de saleté à

l’intérieur du bloc optique, essuyer le réfracteur ou la lentille, puis nettoyer comme

indiqué ci-dessus et remplacer toute garniture d’étanchéité endommagée au besoin.

• NE PAS INSTALLER UN PRODUIT ENDOMMAGÉ ! Ce luminaire a été emballé

de manière à ce que les pièces ne subissent pas de dommages lors du transport.

Veuillez inspecter et conﬁrmer le bon état. Toute pièce endommagée ou brisée

lors de l’assemblage ou après devrait être remplacée.

• Recyclage : pour accéder à l’information sur le recyclage des produits électro-

niques DEL, veuillez visiter www.epa.gov.

• Ces directives n’entendent pas couvrir tous les détails, tous les modèles

d’équipement, ni prévoir toute éventualité liée à l’installation, au fonctionnement

ou à l’entretien de cet équipement. Pour toute autre information ou en cas d’un

problème non résolu par le présent document, l’acheteur ou le propriétaire est prié

de contacter Acuity Brands Lighting, Inc.

• Couper ou éteindre l’alimentation électrique avant l’installation ou l’entretien.

• Vériﬁ er que la tension d’alimentation est adéquate en la comparant à l’information

sur l’étiquette du luminaire.

• Effectuer toutes les connexions et la mise à la terre conformément au National

Electrical Code (NEC) et aux exigences de tout autre code local applicable.

• Touteslesconnexionsdoiventêtreprotégéesd’uncapuchondeconnexionhomologuéUL.

• Porter des gants et des verres de sécurité en tout temps pour retirer le luminaire de

la boîte, l’installation, l’entretien ou les travaux de maintenance.

• Éviter d’exposer directement les yeux à la source lumineuse lorsqu’allumée.

AVERTISSEMENT RISQUE DE BRÛLURE

• Permettre le refroidissement de la lampe et du luminaire avant la manipulation. Ne

pas toucher au boîtier ou à la source lumineuse.

• Ne pas dépasser la puissance maximale indiquée sur l’étiquette du luminaire.

• Observer tous les avertissements, toutes les recommandations et toutes

les restrictions du fabricant sur : le type de pilote, la position d’utilisation,

l’emplacement et les méthodes de montage, le remplacement et le recyclage.

• Éloigner toutes les matières combustibles ou infl ammables de la lampe et de la lentille.

• Ne pas employer à proximité des personnes, des matières combustibles ou des

substances sensibles à la chaleur ou la sécheresse.

• Ne jamais connecter des composantes en charge.

• Ne pas monter ou supporter ces appareils d’une manière pouvant causer l’abrasion

de la gaine externe ou endommager l’isolant des ﬁls.

• Sauf si contraire aux spéciﬁcations du produit individuel : Ne jamais connecter

directement un produit DEL sur un gradateur, un détecteur de présence, un

temporisateur ni sur aucun autre appareil de contrôle de ce type. Les appareils

DEL doivent être alimentés directement hors d’un circuit à interrupteur.

• Sauf en cas de spéciﬁ cations contraires individuelles des produits : Ne pas limiter

la ventilation du luminaire. Permettre un espace libre sufﬁ sant autour du luminaire.

Éviter de couvrir les appareils DEL d’un matériau isolant, alvéolaire ou tout autre

matériau empêchant le refroidissement de l’unité par convexion ou conduction.

• Sauf en cas de spéciﬁ cations contraires individuelles des produits : Ne pas

dépasser la température ambiante maximale de service admissible.

• Utiliser le luminaire qu’à l’endroit prévu à cet effet.

• Les produits DEL sont sensibles à la polarité. S’assurer d’une polarité adéquate

avant l’installation.

• Décharge électrostatique (DES) : Une DES peut endommager les appareils DEL.

Un équipement de mise à la terre de protection individuelle doit être porté lors de

l’installation ou l’entretien de l’unité.

• Ne pas toucher aux composantes électriques individuelles, car cela peut causer une

DES, réduire la durée de vie de la lampe ou compromettre la performance de l’unité.

• Certains composants internes des luminaires peuvent ne pas être réparables.

Dans le cas peu probable où l’appareil aurait besoin d’une réparation,

immédiatement cesser de l’utiliser et faire appel à un représentant ABL.

• Avant de procéder au montage, toujours lire toutes les instructions de montage des

luminaires pour connaître les autres avertissements qui leur sont propres.

• Vériﬁez que le système de distribution électrique a une mise à la terre appropriée.

Une mauvaise mise à la terre peut entraîner une défaillance du luminaire et

annuler la garantie.

Tous les luminaires qui contiennent des dispositifs électroniques générant des

fréquences supérieures à 9 kHz à partir d’un composant situé à l’intérieur du

luminaire sont conformes à la section 15 des règles de la Commission fédérale

des communications. Son fonctionnement doit respecter les deux conditions

suivantes : (1) Ce dispositif ne doit générer aucune interférence préjudiciable

(2) Ce dispositif doit accepter n’importe quelle interférence reçue, y compris

les interférences pouvant entraîner un fonctionnement non souhaité.

Ne pas observer ces instructions pourrait annuler les garanties du produit.

Pour une liste complète des conditions et modalités, veuillez visiter

www.acuitybrands.com. Acuity Brands Lighting, Inc. décline toute

responsabilité pour les réclamations résultant d’une installation ou

manipulation inadéquate ou négligente de ses produits.

Avertissements généraux de ABL sur les produits DEL, pub. no 503.203

IMPORTANTES CONSIGNES DE

SÉCURITÉ SUR L’ÉCLAIRAGE DEL

INSTRUCCIONES DE SEGURIDAD

IMPORTANTES SOBRE EL LED

IMPORTANT SAFETY INSTRUCTIONS

WARNING RISK OF ELECTRIC SHOCK

CAUTION RISK OF INJURY

ADVERTENCIA: RIESGO DE CHOQUE ELÉCTRICO

PRECAUCIÓN: RIESGO DE LESIONES

PRECAUCIÓN: RIESGO DE DAÑO PARA EL PRODUCTO

AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE

MISE EN GARDE RISQUE DE BLESSURE

MISE EN GARDE RISQUE D’INCENDIE

MISE EN GARDE : RISQUE DE CAUSER DES DOMMAGES AU PRODUIT

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THIS INSTRUCTIONS

and deliver to owner after installation

PAGE: 1 of 19

When using electrical equipment, basic safety precautions

should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR

SIGNIFICANT PROPERTY DAMAGE. For your protection, read and follow these warnings and instructions carefully before installing or

maintaining this equipment. These instructions do not attempt to cover all installation and maintenance situations. If you do not understand

these instructions or additional information is required, contact LITHONIA LIGHTING or your local LITHONIA LIGHTING distributor.

WARNING: RISK OF ELECTRIC SHOCK –NEVER CONNECT TO, DISCONNECT FROM, OR SERVICE WHILE EQUIPMENT IS

ENERGIZED.

WARNING: DO NOT USE ABRASIVE MATERIALS OR SOLVENTS. USE OF THESE SUBSTANCES MAY DAMAGE FIXTURE,

WHICH MAY RESULT IN PERSONAL INJURY.

WARNING: RISK OF PERSONAL INJURY –This product may have sharp edges. Wear gloves to prevent cuts or abrasions when removing

from carton, handling, installing and maintaining this product.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacturer’s warnings,

recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.

IMPORTANT SAFEGUARDS

•Do not use outdoors. Suitable for use in damp location 32°F –104°F (0°C –40°C).

•Consult local building code for approved wiring and installation.

•Disconnect A.C. power before servicing and installation.

•Do not mount near gas or electric heater.

•Do not use this equipment for other than intended use.

•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

•All servicing on this equipment should be performed by qualified personnel only.

•Equipment should be mounted in locations and at heights where it will not be subject to tampering by

unauthorized personnel.

•Use caution when servicing batteries.

•Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.

IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should always be followed,

including the following:

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 2 of 19

BACK MOUNT INSTALLATION

IMPORTANT: Provide each unit with a single-phase AC un-switched power supply from a circuit used for normal lighting.

“UVOLT” product versions operate from 120 volts through 347 volts. PRODUCT DAMAGE WILL OCCUR IF THE RATED INPUT VOLTAGE IS EXCEEDED.

NOTE: The battery must be connected to the charger board prior to applying AC power to the unit. Battery damage may occur if the battery is connected longer than 24

hours without continuous AC power provided. See also “Important Battery Information”.

NOTE: The maximum mounting height of TCC 350L from ground is 17.1 feet, TCC 750L and TCC 750L HO from ground is 25.4 feet to meet the minimum illumination

requirements of NFPA 101 (current Life Safety Code).

NOTE: Do not connect battery or power unit until remote units (if applicable) are fully connected and wires are isolated from other potentials (i.e. remote wires shall be

isolated from earth ground).

NOTE: Supports 4” Square, 4” Octagon or a single rectangular (4”x 2.125”) J-Box.

1. Remove the side cover by unscrewing two side screws and remove side cover. (See Fig A)

2. Slide out front panel, if applicable, to permit installation process. Installer will need to remove bonding screw on Standard

Exit Signs.

NOTE: for side mounting of lampheads see section Side Mounting Lampheads.

3. Mounting options:

•J-Box Mounting: knock out the appropriate mounting pattern and the wire pass hole in the backplate to fit the J-box

being used. Approved J-Box sizes are 4” Square (With or without plaster ring), 4” Octagon, or a single rectangular J-

Box.

•Conduit Mounting: knock out the appropriate conduit and mount the backplate to the wall in the desired location

using the keyhole knockouts (See Fig. A). Attach a conduit hub to desired conduit mount hole on the frame. An

additional screw may be required at the j-box center bottom hole to pull the unit back into the wall as visible from

the bottom of the unit. Do not use center knockout if the HO option is used to prevent interference of the conduit

with the battery.

SIDE SCREWS

Fig. A

CONDUIT MOUNT

KNOCKOUTS

KEY HOLES

J-BOX HOLES

Standard Exit Sign

BONDING SCREW

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 3 of 19

BACK MOUNT INSTALLATION (CONT.)

4. Use code-approved connectors to make the connection inside the unit. Connect the hot wire to the red lead. Connect neutral

wire to the white lead. The ground wire (green lead) needs to be connected in accordance with the local codes. DO NOT

energize the circuit at this time (See Wiring Diagram). For Units with Remote Lamp Wires: Connect remote wires to the

remote output. The yellow wire is the positive remote wire and blue is the negative (See Wiring Diagram). If no remote

lamps are connected, make sure remote wire harness is removed from the unit to prevent shorting. Wires shall be neatly

dressed inside the unit to prevent any shadowing of the exit sign (i.e., routed closely to side of unit).

5. Connect the battery to the main board. Refer to the wiring diagram below.

6. Proceed to step 9 for Chicago Glass Panel.

7. Proceed to step 10 and 11 for Standard Exit Sign.

8. Proceed to step 12 for Running Man Panel.

9. Chicago Glass Panel. Slide Chicago Glass Panel into grooves (See Fig B). Proceed to step 13.

10. Standard Exit Sign: If directional chevron is desired slide red diffuser out and knockout desired chevron. Replace red diffuser

or use green diffuser if desired. (See Fig C)

Fig. B

GROOVES

SLIDE PANEL

REMOVE RED DIFFUSER

Fig. C

REMOVE DESIRED CHEVRON(S) REPLACE WITH RED OR GREEN DIFFUSER

UL924 CERTIFIED GLASS PANELS

CHP ENA CHP SNA

CITY OF CHICAGO, IL

NON UL924 CERTIFIED

GLASS PANELS

CHP ERA

CHP ELFA

CHP EDA

CHP SRA

CHP SLFA

CHP SDA

CHP ENA CHP SNA

CITY OF CHICAGO, IL

NON UL924 CERTIFIED

GLASS PANELS

CHP ERA

CHP ELFA

CHP EDA

CHP SRA

CHP SLFA

CHP SDA

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 4 of 19

BACK MOUNT INSTALLATION (CONT.)

11. Standard Exit Sign. Slide Standard Exit Panel into grooves (See Fig D), with Standard Exit Panel facing out, and torque

bonding screw to 10.6 in-lbs. (1.2Nm) Proceed to step 15. It may simplify installation if you allow the colored diffuser to side

into the far groove ahead of the metal plate. Torque the bonding screw s to 10.6 in-lbs (1.2Nm). If double-sided panel is

desired, remove backplate and add panels to both sides. Proceed to step 15.

12. Running Man: Place the Running Man sign over the white diffuser and slide stacked signs into the grooves with Running Man

panel facing outward, RM no Arrow panel is shown. If double-sided panel is desired, remove back plate and add panels to

both sides. (See Fig. E).

Fig. D

GROOVES

BONDING SCREW

Note: There is a

similar screw on

the backplate that

if removed should

be torqued to the

same value.

GROOVES

DIFFUSER

RM PANEL

Fig. E

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 5 of 19

BACK MOUNT INSTALLATION (CONT.)

13. Replace the side cover and torque the side screws to 10.6 in-lbs (1.2Nm) (See Fig F).

14. Energize the unit with AC supply. The charge indicator will illuminate green for charging. Allow battery to charge for 24 hours

before initial testing.

15. Adjust and focus the lighting heads as required.

Fig. F

TEST SWITCH

AND LED

SIDE SCREWS

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 6 of 19

TOP/SIDE MOUNT INSTALLATION

1. Remove the side cover by unscrewing the two side screws and remove side cover. (See Fig. G)

2. Slide out front panel, if applicable, to permit installation process. Installer will need to remove bonding screw on Standard

Exit Signs.

3. To use with a canopy, remove the canopy screws and remove the desired knockout (See Fig H). Side canopy mount is shown.

The battery tray will also need be removed to route harness through the desired knockout, then reinstall battery tray (See Fig

I, J, K, and L). For top mount, while battery tray is removed, lamps need to be moved to the side or removed. See Relocating

Lampheads to Side for Top Mount section to move lampheads and then proceed with installation.

SIDE SCREWS

Fig. G

BACK PANEL

SIDE MOUNT CANOPY SCREWS

TOP SIDE CANOPY SCREWS

KNOCKOUTS

Fig. H

Standard Exit Sign

BONDING SCREW

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 7 of 19

TOP/SIDE MOUNT INSTALLATION (CONT.)

Fig. I

ROUTE HARNESS THROUGH TOP KNOCKOUT FOR TOP MOUNT THEN REINSTALL POWER TRAY.

PULL HARNESS BACK THROUGH HOLE FOR TOP MOUNT AND SIDE MOUNT

Fig. J

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 8 of 19

TOP/SIDE MOUNT INSTALLATION (CONT.)

Fig. K

ROUTE HARNESS INSIDE BATTERY TRAY AND DOWN THE SIDE THROUGH KNOCKOUT FOR SIDE MOUNT

Fig. L

RE-INSTALL BATTERY TRAY SCREWS AND TORQUE TO 10.6 in-lbs (1.2Nm).

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 9 of 19

4. Mount the canopy to the unit at the desired location (top or side) and torque the canopy screws to 10.6 in-lbs (1.2Nm) (See

Fig H).

5. Pass the wires through the wall of the unit and canopy cover for routing to the junction box. Wires shall be neatly dressed

inside the unit to prevent any shadowing of the exit sign (i.e., routed closely to side of unit).

6. Use code-approved connectors to make the connection inside the unit. Connect the hot wire to the red lead. Connect neutral

wire to the white lead. The ground wire (green lead) needs to be connected in accordance with the local codes. DO NOT

energize the circuit at this time (See Wiring Diagram). For Units with Remote Lamp Wires: Connect remote wires to the

remote output. The yellow wire is the positive remote wire and blue is the negative (See Wiring Diagram). If no remote

lamps are connected, make sure remote wire harness is removed from the unit to prevent shorting.

7. Mount canopy to the wall if the canopy is mounted on the side or ceiling if the canopy is mounted on the top.

8. Connect the battery to the main board. Refer to the wiring diagram below.

9. Proceed to step 12 for Chicago Panel.

10. Proceed to step 13 and 14 for Standard Exit Sign.

11. Proceed to step 15 for Running Man.

12. Chicago Sign: Slide Chicago Glass Panel into grooves (See Fig M). If a double-sided panel is wanted add panels to both sides.

Proceed to step 16.

13. Standard Exit Sign: If directional chevron is desired slide red diffuser out and knockout desired chevron. Replace red diffuser

or green diffuser if desired. (See Fig N).

TOP/SIDE MOUNT INSTALLATION (CONT.)

Fig. M

GROOVES

SLIDE PANEL

Fig. N

REMOVE RED DIFFUSER REMOVE DESIRED CHEVRON(S) REPLACE WITH RED OR GREEN DIFFUSER

UL924 CERTIFIED GLASS PANELS

CHP ENA CHP SNA

CITY OF CHICAGO, IL

NON UL924 CERTIFIED

GLASS PANELS

CHP ERA

CHP ELFA

CHP EDA

CHP SRA

CHP SLFA

CHP SDA

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 10 of 19

14. Standard Exit Sign: Slide panel into grooves (See Fig O) and torque bonding screw to 10.6 in-lbs (1.2Nm) . If a double-sided

panel is desired, add panels to both sides. It may simplify installation if you allow the colored diffuser to side into the far

grove ahead of the metal plate. Torque bonding screws on both sides (front and back). Proceed to step 16.

15. Running Man Sign: Place the Running Man sign over the white diffuser and slide stacked signs into the grooves with

Running Man panel facing outward, RM no Arrow panel is shown. If double-sided panel is desired, remove back

plate and add panels to both sides. (See Fig. P)

TOP/SIDE MOUNT INSTALLATION (CONT.)

Fig. O

Fig. P

GROOVES

DIFFUSER

RM PANEL

GROOVES

SLIDE PANEL

BONDING SCREW

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 11 of 19

16. Replace the side cover and torque the side screws to 10.6 in-lbs (1.2Nm) (See Fig Q).

17. Energize the unit with AC supply. The charge indicator will illuminate green to indicate the unit is charging. Allow battery to

charge for 24 hours before initial testing.

18. Adjust and focus the lighting heads as required.

TOP/SIDE MOUNT INSTALLATION (CONT.)

TEST SWITCH AND LED

(EMERGENCY ONLY)

SIDE SCREWS

Fig. Q

LED Steel Combo Emergency Unit

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 12 of 19

Relocating Lampheads to Side for Top Mount –Caution: You may have

restricted aiming in a side mount application due to the lampheads hitting the wall. Rotation

downward is not limited; side rotation is very limited.

1. Remove the nut and washers connecting the lampheads to the main housing.

2. Pull the lampheads and wiring out through the main housing.

3. Using a hammer and a punch, carefully knockout the small double D size holes on the side of the main housing to

mount the lampheads. Punch holes from the outside in.

4. Route the wire and the lamphead through the knockout orienting lamphead in the double D hole to give you the

desired aiming.

5. Slide the washer and nut into position and secure the lamphead to the main housing. Torque the nut to 31 in-lbs

(3.5nm).

6. Connect the lamphead wires to the main board connectors. Refer to the wiring diagram above. Be careful to route

wires on side of housing to prevent shadowing of sign.

7. Cover the top knockouts with the plastic inserts included in the accessory bag.

INSTRUCTIONS FOR Lithonia Lighting TCC

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 13 of 19

PENDANT MOUNT INSTALLATION

1. Remove the side cover by unscrewing the two side screws and remove side cover. (See Fig. R)

2. Slide out front panel, if applicable, to permit installation process. Installer will need to remove bonding screw on Standard

Exit Signs.

3. To use with a pendant, remove the battery screws, and battery tray and remove the top middle knockout (See Fig S). Pull

harness back through hole for top pendant mount (See Fig I).

SIDE SCREWS

Fig. R

BACK PANEL

Fig. S

Standard Exit Sign

BONDING SCREW

MIDDLE KNOCK OUT

BATTERY TRAY SCREW

(2ND SCREW IS DIRECTLY

ACROSS ON THE RIGHT SIDE)

BATTERY TRAY

(Pendant mount not included)

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 14 of 19

4. Mount the pendant to the top of unit using ½” Threaded Nipple Conduit Fitting, and a ½” Threaded Conduit Coupler Fitting.

Ensure the Pendant mount does not interfere or make contact with the battery when the tray is installed. (See Fig T)

5. Pull the harness back through the hole and feed into through the pendant, reinstall the battery tray, and torque the screws to

10.6 in lbs (1.2 N ms) (See Fig I and J).

6. Use code-approved connectors to make the connection inside the unit. Connect the hot wire to the red lead. Connect neutral

wire to the white lead. The ground wire (green lead) needs to be connected in accordance with the local codes. DO NOT

energize the circuit at this time (See Wiring Diagram). For Units with Remote Lamp Wires: Connect remote wires to the

remote output. The yellow wire is the positive remote wire and blue is the negative (See Wiring Diagram). If no remote

lamps are connected, make sure remote wire harness is removed from the unit to prevent shorting.

7. Proceed to step 10 for Chicago Panel.

8. Proceed to step 11 and 12 for Standard Exit Sign.

9. Proceed to step 13 for Running Man.

10. Chicago Glass Sign: Slide Chicago Glass Panel into grooves (See Fig U). If a double-sided panel is wanted add panels to both

sides. Proceed to step 16.

PENDANT MOUNT INSTALLATION (CONT.)

Fig. T

GROOVES

SLIDE PANEL UL924 CERTIFIED GLASS PANELS

CHP ENA CHP SNA

CITY OF CHICAGO, IL

NON UL924 CERTIFIED

GLASS PANELS

CHP ERA

CHP ELFA

CHP EDA

CHP SRA

CHP SLFA

CHP SDA

Fig. U

½” THREADED

NIPPLE CONDUIT

FITTING

½” THREADED

CONDUIT COUPLER

FITTING

½” THREADED

NIPPLE CONDUIT

FITTING

½” THREADED

COUPLING CONDUIT

FITTING

PENDANT

½” CONDUIT

(Pendant mount not included)

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 15 of 19

11. Standard Exit Sign: Slide 1 Red or 1 Green Diffuser into Standard Exit Panel Grooves (See Fig V).

12. Standard Exit Sign: Slide Standard Exit Panel into grooves (See Fig W) and torque bonding screw to 10.6 in-lbs (1.2Nm) . If a

double-sided panel is desired, add panels to both sides. It may simplify installation if you allow the colored diffuser to side

into the far grove ahead of the metal plate. Torque bonding screws on both sides (front and back). Proceed to step 16.

13. Place the Running Man sign over the white diffuser and slide both into grooves, RM Arrow panel is shown (See Fig. X). If a

double-sided panel is wanted add panels to both sides.

PENDANT MOUNT INSTALLATION (CONT.)

Fig. W

Fig. X

Fig. V

REMOVE RED DIFFUSER REMOVE DESIRED CHEVRON(S) REPLACE WITH RED OR GREEN DIFFUSER

GROOVES

SLIDE PANEL

GROOVES

WHITE DIFFUSER

RM PANEL

(Pendant mount not included)

BONDING SCREW

Note: There is a

similar screw on

the backplate that

if removed should

be torqued to the

same value.

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 16 of 19

14. Replace the side cover and torque the side screws to 10.6 in-lbs (1.2Nm) (See Fig Y).

15. Energize the unit with AC supply. The charge indicator will illuminate green to indicate the unit is charging. Allow battery to

charge for 24 hours before initial testing.

16. Adjust and focus the lighting heads as required.

PENDANT MOUNT INSTALLATION (CONT.)

Fig. Y TEST SWITCH AND LED

SIDE SCREWS

(Pendant mount not included)

LED Steel Combo Emergency Unit

INSTRUCTIONS FOR Lithonia Lighting TCC

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 17 of 19

OPERATION:

1. To test the equipment, depress the TEST switch, the emergency lights will illuminate.

2. Once you release the TEST switch the emergency lights will turn OFF and the LED indicator will illuminate green for

charging.

3. The charger board will continue charging the battery to maintain a fully charged state.

NOTE: Allow the battery to charge for a minimum of 24 hrs after installation or after a power failure before conducting a

90-minute test.

NOTE: Standard and HO are furnished with a sophisticated solid state transfer switch which will automatically disconnect

the emergency lights from the battery if the battery has been discharged to the end of its useful output. Sign will still

illuminate during AC power only.

MAINTENANCE:

CAUTION: Always turn OFF AC power to the equipment before servicing. Operator should disconnect battery if the lamps are

on to remove power from lampheads before service lampheads. Servicing should be performed only by a qualified service

technician. Only manufacturer SUPPLIED or APPROVED replacement parts must be used.

BATTERY: The battery supplied with this unit requires ZERO maintenance. However, it should be tested periodically and replace

when it no longer operates the connected fixtures for complete duration of a monthly 30-second or annual 90-minute test.

NFPA 101 (current Life Safety Code) requires that all emergency lighting equipment be functionally tested every 30 days for a

minimum of 30 seconds and tested annually for full 90-minute duration. Written records of the testing are to be kept for

examination by the authority having jurisdiction.

Remote Loading Limits

Product Maximum Continuous Remote Loading

TCC HO 6.6W

TCC 2.4W

LED Steel Combo Emergency Unit

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 18 of 19

TROUBLESHOOTING:

1. The sign DOES NOT operate:

a) If the charge indicator light is OFF —Check the circuit breaker and validate the AC supply voltage is present. Also

verify that the pairs of red & black wires are properly connected to the lamp/charger board (see wiring diagram).

b) If the charge indicator light is Red - Check that the battery is properly connected.

2. If local lampheads are not working in Test or Emergency mode and sign is luminated check to make sure lamphead

harnesses are properly inserted into the lamp/charger board.

3. If remote lamps are connected to the equipment and are not working:

a) Turn OFF the AC supply, disconnect battery and disconnect the remote circuit wires from the equipment.

b) Reconnect battery, turn ON the AC supply and depress the test switch.

a) If the local lamps (mounted on the equipment itself) come ON, then check the remote circuit for short or

overload condition and correct as required. Reconnect the circuit wires and restore AC power and battery

connection.

b) If the local lamps don't turn ON after disconnecting the remote circuit wires, then replace battery.

c) If the previous step does not resolve the problem, unit may need to be replaced.

INSTRUCTIONS FOR Lithonia Lighting TCC

LED Steel Combo Emergency Unit

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 19 of 19

Wiring Diagram:

TCC 750L (Non-HO / No Remote Support)

TCC 750L HO & TCC 350L (Remote Support)

FCC Title 47,

Part 15, Subpart B Part No. 912-00378-001

Rev E, 04/2023

INSTRUCTIONS FOR Lithonia Lighting TCC

La page charge ...

Lithonia Lighting TCC Commercial Steel Exit Combo Guide d'installation

Marque: Lithonia Lighting

Modèle: TCC Commercial Steel Exit Combo

Taper: Guide d'installation

Ce manuel convient également à

TCC Commercial Steel Running Man Combo

Télécharger le PDF

rapport

dans d''autres langues

English: Lithonia Lighting TCC Commercial Steel Exit Combo Installation guide

Lithonia Lighting TCC Commercial Steel Exit Combo Guide d'installation

Ce manuel convient également à

Lithonia Lighting TCC Commercial Steel Exit Combo Guide d'installation

dans d''autres langues

Documents connexes

Autres documents