Dorel Home DA6580GR Assembly Manual

Thank you for purchasing from DHP!

Date of Purchase

Y.W. - 2023/02/24

Lot Number (TAKEN FROM CARTON)

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

B34DA658000-100063

1

Weight Limit : 200 Lbs / 91 Kg

DA6580 (Espresso), DA6580W (White), DA6580GR (Gray)

Loft Bed

Twin

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Visit www.dhpfurniture.com/eng/replacement-parts

or call Toll-Free 1-800-267-1739

You can also chat with us at www.dhpfurniture.com

DO NOT RETURN TO THE STORE !

Limited 1 year Warranty

DHP warrants this product to be free from defects in material and workmanship

and agrees to remedy any such defect. This warranty covers one year from the

date of original purchase from authorized retailers. This is solely limited to the

repair or replacement of defective parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly

assembled, subjected to misuse or abuse or which has been altered or repaired

in any way.The warranty does not cover wearing, tearing, fading or splitting of

the fabric (where applicable). Liability for consequential damages is excluded to

the extent exclusion is permitted by law. This warranty gives you specific legal

rights and you may also have other rights which vary from state to state or

province to province.

To obtain warranty service, purchaser must present original bill of sale.

Components repaired or replaced are warranted through the remainder of the

original warranty period only. The defective components will be repaired or

replaced without charge, subject to the terms and conditions described above.

The terms and conditions of the limited warranty are subject to change without

notice. For the latest warranty policy, please visit www.dhpfurniture.com.

● Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and

product.

● Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

● Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

● This product may contain small components. Please ensure that they are kept

away from small children.

● This product is designed for home use and is not intended for commercial use.

Contact Us!

For help with assembly, identifying parts, product information or to order parts,

please contact us: This product is shipped in

1 carton

www.dhpfurniture.com

[email protected]om

1-800-267-1739

Monday to Friday 9am to 9pm (Eastern Time)

Saturday 10 am to 6:30 pm (Eastern Time)

Sunday 11 am to 7pm (Eastern Time)

DHP Consumer Services

12345 Albert Hudon, Suite 100,

Montreal, Quebec H1G 3L1

Do NOT use

powertools

Phillips head screwdriver

needed (not included)

2

100 minute

Read Before Beginning Assembly

●STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example,

but not limited to, hooks, belts and jump ropes.

WARNINGS - Loft Bed: Twin

3

● Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.

● The mattress platform is designed to support a mattress without the need for a posture board or box spring.

● Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.

●USE ONLY COIL SPRING MATTRESSES ON THE UPPER BUNK. FAILURE TO DO SO CAN RESULT IN INJURY.

● Use only mattresses which are 74"-75" long and 37 1/2" - 38 1/2" wide on upper and lower bed. Ensure thickness of mattress does not exceed

6"(152mm). Surface of mattress must be at least 5"(127mm) below the upper edge of guardrails.

● Do not allow children under 6years of age to use the upper bunk.

● Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length

of the bed should be placed against the wall to prevent entrapment between the bed and wall (applicable for bunk beds with full length

guardrails on one side).

● Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage, and that all

connectors are tight.

● Do not allow horseplay on or under the bed and prohibit jumping on the bed.

● Do not use substitute parts. Contact customer service for replacement parts.

● Use of a night light may provide added safety precaution for a child using the upper bunk.

● The use of water or sleep flotation mattresses is prohibited.

● Always use the ladder for entering and leaving the upper bunk.

● Prohibit more than one person on upper bunk.

● Keep these instructions for future reference.

4

PARTS

X

V

R

M

T

back view

W

U

J

L

C

T

K

A

D

O

Q

S

H

L

R

G

F

B

C

P

J

E

I

M

N

E

PARTS LIST

LEFT FRONT POST

1 PC

LEFT BACK POST

1 PC

RIGHT BACK POST

1 PC

RIGHT FRONT POST

1 PC

HEADBOARD CROSS

6 PCS

HEADBOARD CENTER CROSS

1 PC

HEADBOARD CENTER CROSS

1 PC

HEADBOARD PANEL

4 PCS

FRONT SIDE RAIL

1 PC

BACK SIDE RAIL

1 PC

DESK FRONT RAIL

1 PC

SLAT

13 PCS

5

A DCB

E HGF

IK

JL

PARTS LIST

LONG GUARDRAIL

1 PC

SHORT GUARDRAIL

1 PC

LEFT LADDER END

1 PC

RIGHT LADDER END

1 PC

LADDER STEP

5 PCS

GUARDRAIL LEG

2 PCS SHORT GUARDRAIL POST

1 PC

DESK PANEL

1 PC

MON P

QS

RT

6

PARTS LIST

DESK BACK RAIL

1 PC

BOTTOM BACK GUARDRAIL

1 PC

BOTTOM BACK SIDE RAIL

1 PC

SUPPORT POST

1 PC

SPACE BLOCK

2 PCS

7

UWV X

Y

Each part has a unique part

number. Please reference the

appropriate part number when

contacting customer service for

replacement parts.

Before throwing any packaging,

please verify all contents and

make sure you have received

all the parts listed above!

PART UNMBERS

PART

LABELS DA6580

(Espresso)

DA6580W

(White)

DA6580GR

(Gray)

AT1027420 T1027670 T1026970

BT1027430 T1027680 T1026980

CT1027440 T1027690 T1026990

DT1027450 T1027700 T1027000

ET1027460 T1027710 T1027010

FT1027470 T1027720 T1027020

GT1027480 T1027730 T1027030

HT1027490 T1027740 T1027040

IT1027500 T1027750 T1027050

JT1027510 T1027760 T1027060

KT1027520 T1027770 T1027070

LT1027530 T1027780 T1027080

MT1027540 T1027790 T1027090

NT1027550 T1027800 T1027100

OT1027560 T1027810 T1027110

PT1027570 T1027820 T1027120

QT1027580 T1027830 T1027130

RT1027590 T1027840 T1027140

ST1027600 T1027850 T1027150

TT1027610 T1027860 T1027160

UT1027620 T1027870 T1027170

VT1027630 T1027880 T1027180

WT1027640 T1027890 T1027190

XT1027650 T1027900 T1027200

YT1027660 T1027910 T1027210

8

HARDWARE LIST

Ø 1/4" x 100mm Ø 6.5mm x 48mm

JOINT CONNECTOR (4mm HEX HEAD)

12 PCS

WOOD JOINT CONNECTOR (4mm HEX HEAD)

12 PCS

Ø 6.5mm x 100mm Ø 4mm x 35mm Ø 11.8mm x 15mm

WOOD JOINT CONNECTOR (4mm HEX HEAD)

26 PCS

FLAT HEAD SCREW

10 PCS

BARREL NUT

12 PCS

Ø 4mm x 30mm Ø 10mm x 50mm

FLAT HEAD SCREW

6 PCS

WOOD DOWEL

44 PCS

ALLEN KEY

1 PC

1

876

543

2

9

HARDWARE LIST

Ø 1/4" x 64mm Ø 8mm x 30mm Ø 1/4" x 32mm

JOINT CONNECTOR (4mm HEX HEAD)

7 PCS

WOOD DOWEL

2 PCS

JOINT CONNECTOR (4mm HEX HEAD)

4 PCS

Ø 9mm x 17mm Ø 1/4" x 15mm 30mm x 30mm x 18mm Ø 3.5mm x 19mm

HEX CAP

2 PCS

JOINT CONNECTOR

(4mm HEX HEAD)

12 PCS

L SHAPED METAL PLATE

6 PCS

FLAT HEAD SCREW

2 PCS

9

10

Hardware Pack

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step instructions.

The screw(s), bolt(s) to be used at each step are

shown in actual size in the lower right corner of the page.

DA6580 (Espresso),

DA6580GR (Gray) HP#: TDA6580-01

DA6580W (White) HP#: TDA6580W-01

10 11

12 13 14 15

Step 1

One of the panel Hhas a label on it, Use it

during this step.

Insert wood dowels (7) into the ends of the

cross Ex3, cross F.

Attach posts A &Bto the crosses using the

wood joint connectors (3) as shown.

Use the Allen key (8) to tighten all joint

connectors.

F

B

H

E

A

E

H

E

3

7

3

87

7

3

X8

3

7

11

Step 2

Insert wood dowels (7) into the ends of the

cross Ex3, cross G.

Attach posts C &Dto the crosses using the

wood joint connectors (3) as shown.

Use Allen key (8) to tighten the wood joint

connectors (3).

12

G

D

H

E

C

E

H

E

3

7

3

7

3

X8

3

7

Step 3

Do not fully tighten bolts in this step, this will

assembly in the following steps.

Insert wood dowels (7) into each end of

the M&U&V&K.

Attach the M&U&Vto posts B &C,

and secure using joint connectors (3).

Attach the K to cross F&Gand secure using

joint connectors (2).

B

U

K

M

V

C

F

G

2

3

7

3

7

3

7

2

37

X8X10

3

7

X2

2

13

Step 4

Insert barrel nuts (5) into rails I &J&W as

shown.

Attach the rails I &J&W to the posts

B&C,A&Dusing the joint connectors (1).

14

W

B

K

J

M

C

I

U

V

5

1

5

1

5

X12

1

5

D

A

Step 5

Insert wood dowels (7) in the ends of short

guardrails N, Attach short guardrails N to

post A with wood joint connectors (3).

Insert wood dowels (10) in the ends of short

guardrails N, Attach short guardrails N to

post S with wood joint connectors (11).

Attach the guardrail post Sto rail Iwith joint

connectors (11) and hex cap (12) as shown.

I

S

N

A

3

12

11

10

7

X2 X2

3

10

X2 X4

11

12

X2

7

15

Step 6

Attach the support post Xto rail U&V&Wwith

joint connectors (9).

16

V

U

WX

9

X3

9

Step 7

Insert wood dowels (7) into the K &U&X as

shown.

Attach the L shaped metal plate (14) with flat

head screws (13) to the U&X.

G

X

U

F

K

7

14

13

14 7

7

X6

13

X6

14

X6

7

17

Step 8

Attach the support post Xto desk panel Twith

joint connectors (13).

Attach the desk front rail Kto desk panel Twith

joint connectors (9).

NOTE: Fully tighten all joint connector installed

in previous steps.

18

X

U

K

T

9

13

9

13

X4

9

X6

13

Step 9

Attach slats Lx13 to bottom side rails I& J with

flat head wood screws (4).

Use space block Y to space them out evenly as

shown.

Use a Phillips head screwdriver (not included)

to install all screws.

J

IL

4

X26

4

Y

19

Step 10

Insert wood dowels (7) into the ends of the

ladder steps Qx5.

Attach ladder ends O &P to ladder steps Qwith

wood joint connectors (2).

Tighten the wood joint connectors (2) with the

Allen key (8).

20

O

P

Q

2

7

X10

72

La page charge ...

Dorel Home DA6580GR Assembly Manual

Ce manuel convient également à

Dorel Home DA6580GR Assembly Manual

dans d''autres langues