Faber Cristal 36 SS 300 cfm Guide d'installation

Marque: Faber

Modèle: Cristal 36 SS 300 cfm

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

CRIS36SS300 CRIS36SS400 CRIS36SS600

CRIS30SS300 CRIS30SS400 CRIS30SS600

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

NEW CRISTAL

Version 06/14 - Page 1

READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. b) Always turn

hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Pepper-corn Beef Flambé). c)

Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. d) Use proper pan size. Always use

cookware appropriate for the size of the surface element.

WARNING:aBased on “Kitchen Firesafety Tips” published by NFPA. - TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close-fitting

lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go

out immediately EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN - You may be

burned. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. Use an

extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is

small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to

an exit.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking surface or countertop.

This minimum clearance may be higher depending on local building code. For example, for gas ranges, a minimum of 30"

may be required. Overhead cabinets on both sides of this unit must be a minimum of 24" above the cooking surface or

countertop. Consult the cooktop or range installation instructions given by the manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home Construction and

Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home Construction and Safety, Title 24, HUD,

Part 280). Four wire power supply must be used and the appliance wiring must be revised. See Electrical Requirements.

LISEZ BIEN CETTE FICHE AVANT D'INSTALLER LA HOTTE

AVERTISSEMENT - POUR MINIMISER LE RISQUE D’UN FEU DE GRAISSE SUR LA TABLE DE CUISSON : a) Ne jamais

laisser un élément de la table de cuisson fonctionner sans surveillance à la puissance de chauffage maximale; un renversement/

débordement de matière graisseuse pourrait provoquer une inflammation et le génération de fumée. Utiliser toujours une puissance

de chauffage moyenne ou basse pour le chauffage d’huile. b) Veiller à toujours faire fonctionner le ventilateur de la hotte lors d’une

cuisson avec une puissance de chauffage élevée ou lors de la cuisson d’un mets à flamber (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé). c) Nettoyer fréquemment les ventilateurs d’extraction. Veiller à ne pas laisser de la graisse s’accumuler

sur les surfaces du ventilateur ou des filtres. d) Utiliser toujours un ustensile de taille appropriée. Utiliser toujours un ustensile de

taille adapté à la taille de l’élément chauffant.

AVERTISSEMENT:Basé sur "Kitchen Firesafety Tips" publié par NFPA. - POUR PRÉVENIR LES BLESSURES EN CAS

DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES: ÉTOUFFEZ LE FEU avec un couvercle métallique et fermez le

brûleur. Si le feu ne s'éteint pas tout de suite, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS. NE TOUCHEZ

JAMAIS UNE CASSEROLE EN FLAMMES. N'UTILISEZ JAMAIS DE L'EAU ou un torchon mouillé pour éteindre le feu -

ce qui pourrait causer une explosion de vapeur. N'utilisez un extincteur que si: 1. Vous avez un modèle ABC et vous

connaissez bien son mode d'emploi. 2. Le feu est petit et peu répandu. 3. Les pompiers sont déjà prévenus. 4. Vous avez une

sortie derrière vous.

TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE DOIT ÊTRE SCELLÉ

Gardez 24 po. de hauteur entre le bas de la hotte et la surface de cuisson. Cette hauteur minimum peut être plus haute suivant le

code municipal. Par exemple, les cuisinières à gaz peuvent requérir 30 po. de hauteur. Les armoires au-dessus de chaque

côté devront être au moins à 24 po. au-dessus de la surface de cuisson. Consultez la fiche technique avant de découper les

armoires. L'installation de cette hotte doit être conforme aux Réglements de Manufactured Home Construction and Safety

Standards, titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction and Safety Standards,

titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction and Safety, titre 24, HUD, Section

280). Le branchement électrique se fait avec une raccordement à 4 fils. Consultez la fiche technique électrique.

CRISTAL HC SS - Halogen

Stainless Slideout Rangehood

• Installation Instructions

• Use and Care Information

READ AND SAVE THESE INSTRUCTIONS

The Installer must leave these instructions with the homeowner.

The homeowner must keep these instructions for future reference

and for local electrical inspectors' use.

CAUTION:- TToo rreedduuccee rriisskk ooff ffiirree aanndd ttoo pprrooppeerrllyy eexxhhaauusstt aaiirr,, bbee ssuurree ttoo dduucctt aaiirr oouuttssiiddee –– DDoo nnoott vveenntt eexxhhaauusstt aaiirr iinnttoo ssppaacceess

wwiitthhiinn wwaallllss oorr cceeiilliinnggss oorr iinnttoo aattttiiccss,, ccrraawwll ssppaacceess,, oorr ggaarraaggeess..

PRUDENCE:- -- AAffiinn ddee rréédduuiirree lleess rriissqquueess dd''iinncceennddiiee aassssuurreezz--vvoouuss qquuee ll''aaiirr ssooiitt ccoorrrreecctteemmeenntt éévvaaccuuéé àà ll''eexxttéérriieeuurr.. LL''aaiirr nnee ddooiitt ppaass êêttrree

éévvaaccuuéé ddaannss lleess eessppaacceess lliibbrreess eennttrree lleess ppaarrooiiss oouu ffaauuxx ppllaaffoonnddss,, aauuvveennttss,, ggaarraaggeess..

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbythe National Fire ProtectionAssociation (NFPA),andthe American

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a

nonmetallic thermal break should be installed to minimize conduction of outside temperatures as

part of the vent system. The damper should be on the cold air side of the thermal break. The break

should be as close as possible to where the vent system enters the heated portion of the house.

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay

fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with

the electrical rating of this unit as specied on the serial/rating plate located inside the unit near the eld

wiring compartment.

Version 06/14 - Page 4

CUT-OUT

CRISTAL HC DIMENSIONS

FRONT TRIM OPTIONS

The Cristal HC comes with a stainless steel front strip installed. Optional black and white kits are available for purchase.

For a custom front strip, a local cabinet shop can make a strip to match your cabinets.

CUSTOM FRONT TRIM DIMENSIONS

1 15/32"

3/4"

29 7/8" or 35 7/8"

25 1/2” - 31 1/2”

10”

25 1/2” - 31 1/2”

13/16”

17 1/2” - 23 1/2”

5 7/8”

Pre-Planning Your Installation -

Important: The recommended height to install this hood

off the cooktop is a minimum of 24" and a maximum of 30” for maximum effectiveness. Also

consult the cooktop manufacturer’s recommendation. NOTE: If direct rear venting, use the side

dimensional diagram below on the right. For top venting (comes standard in this position),

use the left dimensional diagram. Refer to page 5 for directions for direct rear venting.

3 15/16”

CRISTAL HC SIDE DIMENSIONS

(TOP VENT - STANDARD)

CRISTAL HC SIDE DIMENSIONS

(DIRECT REAR VENT OPTION)

3 15/16”

36" RANGEHOOD REAR INFORMATION

30" RANGEHOOD REAR INFORMATION

DRAFT 25-MAY-2020 18:52

Palazzi, Walter

15-Nov-2019

Released

= =

DRAFT 25-MAY-2020 18:52

Version 06/14 - Page 5

9.0 feet

10.0 feet

0.0 feet

19.0 feet

TOOLS NEEDED FOR INSTALLATION

• Saber Saw or Jig Saw

• Drill

• 1 1/4" Wood Drill Bit

• Pliers

• Phillips Screwdriver

• Wire Stripper or Utility Knife

• Metal Snips

• Measuring Tape or Ruler

• Level

• Pencil

• Caulking Gun

• Duct Tape

PARTS SUPPLIED FOR INSTALLATION

• 1 Backdraft Damper

• 1 Vent Grate (for recirculating installations only)

• 1 Vinyl Trim

• 1 Literature Package

PARTS NEEDED FOR INSTALLATION

• 2 Conduit Connectors

• Power Supply Cable

• 1 Wall or Roof Cap

• All Metal Ductwork

PLAN THE DUCTWORK

The Cristal HC slideout rangehood is designed to offer wide exibility of installations.

The rangehood can be ducted vertically or horizontally through a 6" round vent.

The unit can also be installed in a recirculating conguration. The unit comes

standard in the top venting position. FIGURES 1 and 2 show vertical and horizontal

installations for this unit. FIGURE 3 shows recirculating installation.

The Cristal HC requires 6" round ductwork. To ensure that the blower performs to

its highest possible capacity, ductwork should be as short and straight as possilbe.

RECIRCULATING INSTALLATIONS

For recirculating installations (FIGURE 3), Charcoal Filters are necessary. Remove all four grease lters and set aside. Attach

one charcoal lter to each end of the blower. Each charcoal lter attaches to the black grid on the side of the blower. Rotate

the lter clockwise to install and counterclockwise to remove (FIGURE 3A). Replace all four grease lters. Some ductwork

must be installed to exhaust the rangehood back into the kitchen, either at the top of the cabinet or at the face of the soft. A

plastic vent grate (FIGURE 3B) supplied with the rangehood can be used to cover the duct opening. This duct work must not

terminate into a dead air space.

FIGURE 3A

45˚ Elbow

90˚ Elbow

90˚ Flat Elbow

Wall Cap

FIGURE A

9 Feet Straight Duct

2 - 90˚ Elbows

Wall Cap

Total System

FIGURE B

3.0 feet

5.0 feet

12.0 feet

0.0 feet

VERTICAL

DUCTING

FIGURE 2

HORIZONTAL

DUCTING

FIGURE 1

For direct rear venting (FIGURE 2), you must

change the blower position. Remove the 12

screws that hold the metal housing to the

rangehood body. Remove the 4 screws that

hold the blower housing to the metal housing.

Rotate the blower 90 degrees toward the back

and then ip it over 180 degrees. Be sure that

the power supply cable is properly positioned.

Replace all screws, making sure that they are

rmly fastened.

cabinet

ceiling

6” round

duct

hood

cabinet

ceiling

6” round

duct

hood

soft

vent grate

FIGURE 3B

FIGURE 3

For satisfactory performance the duct run should

not exceed 50 equivalent feet if ducted using the

required minimum 6" round duct. The equivalent

feet in FIGURE A for each piece of duct in the

system An example is given in FIGURE B. For

best results, use no more than three 90°

elbows. Make sure that there is a minimum of

24" of straight duct between elbows if more

than one is used. Do not install two elbows

together. If you must elbow right away, do it

as far away from the hood's exhaust opening

as possible.

Version 06/14 - Page 6

OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY

ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT

• Charcoal Filters

For non-vented installations only, replace charcoal

lters as needed part # FILTER1

• CFM Reducer Kit

To reduce cfm to below 300 cfm for use in

make up air environments part # CFMRED

• Universal Make Up Air Damper 6"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER6

• Universal Make Up Air Damper 8"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER8

• Front Trim Kits

Replace stainless trim on the slide out hood with a

black or white trim (available in 30" or 36")

CRTRIM30WH (30" white)

CRTRIM30BK (30" black)

CRTRIM36WH (36" white)

CRTRIM36BK (36" black)

• Filtres à charbon

Pour les installations non ventilé seulement, rem-

placer le charbon de bois

ltres au besoin partie # FILTER1

• Réducteur de CFM Kit

Pour réduire cfm à 300 cfm ci-dessous pour une

utilisation dans

compenser milieux aériens partie # CFMRED

• Universal Make Up registre d'air 6"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER6

• Universal Make Up Air Amortisseur 8"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER8

• Front Bordure Kits

Remplacer la garniture inoxydable sur la diapositive

sur le capot avec un

équilibre noir ou blanc (disponible en 30 "ou 36")

CRTRIM30WH (30 "blanc)

CRTRIM30BK (30 "noir)

CRTRIM36WH (36 "blanc)

CRTRIM36BK (36 "noir)

Version 06/14 - Page 6

OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY

ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT

• Charcoal Filters

For non-vented installations only, replace charcoal

lters as needed part # FILTER1

• CFM Reducer Kit

To reduce cfm to below 300 cfm for use in

make up air environments part # CFMRED

• Universal Make Up Air Damper 6"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER6

• Universal Make Up Air Damper 8"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER8

• Front Trim Kits

Replace stainless trim on the slide out hood with a

black or white trim (available in 30" or 36")

CRTRIM30WH (30" white)

CRTRIM30BK (30" black)

CRTRIM36WH (36" white)

CRTRIM36BK (36" black)

• Filtres à charbon

Pour les installations non ventilé seulement, rem-

placer le charbon de bois

ltres au besoin partie # FILTER1

• Réducteur de CFM Kit

Pour réduire cfm à 300 cfm ci-dessous pour une

utilisation dans

compenser milieux aériens partie # CFMRED

• Universal Make Up registre d'air 6"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER6

• Universal Make Up Air Amortisseur 8"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER8

• Front Bordure Kits

Remplacer la garniture inoxydable sur la diapositive

sur le capot avec un

équilibre noir ou blanc (disponible en 30 "ou 36")

CRTRIM30WH (30 "blanc)

CRTRIM30BK (30 "noir)

CRTRIM36WH (36 "blanc)

CRTRIM36BK (36 "noir)

"When used in recirculation mode, to Reduce the Risk of

Fire and Shock use only conversion kit Model FILTER 1 -

FILTER1LL"

Version 06/14 - Page 6

OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY

ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT

• Charcoal Filters

For non-vented installations only, replace charcoal

lters as needed part # FILTER1

• CFM Reducer Kit

To reduce cfm to below 300 cfm for use in

make up air environments part # CFMRED

• Universal Make Up Air Damper 6"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER6

• Universal Make Up Air Damper 8"

Brings fresh air back into the home thru an automatic

damper when the hood is on #MUDAMPER8

• Front Trim Kits

Replace stainless trim on the slide out hood with a

black or white trim (available in 30" or 36")

CRTRIM30WH (30" white)

CRTRIM30BK (30" black)

CRTRIM36WH (36" white)

CRTRIM36BK (36" black)

• Filtres à charbon

Pour les installations non ventilé seulement, rem-

placer le charbon de bois

ltres au besoin partie # FILTER1

• Réducteur de CFM Kit

Pour réduire cfm à 300 cfm ci-dessous pour une

utilisation dans

compenser milieux aériens partie # CFMRED

• Universal Make Up registre d'air 6"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER6

• Universal Make Up Air Amortisseur 8"

Apporte de l'air frais de nouveau dans la maison à

travers un amortisseur automatique lorsque le capot

est sur # MUDAMPER8

• Front Bordure Kits

Remplacer la garniture inoxydable sur la diapositive

sur le capot avec un

équilibre noir ou blanc (disponible en 30 "ou 36")

CRTRIM30WH (30 "blanc)

CRTRIM30BK (30 "noir)

CRTRIM36WH (36 "blanc)

CRTRIM36BK (36 "noir)

- # FILTER1LL

Version 06/14 - Page 7

INSTALL THE RANGEHOOD

1. Remove the rangehood from the carton and place on a

flat surface. Cover the surface to prevent accidental damage.

Remove all parts including the backdraft damper, plastic grille

and literature package before discarding the carton. Remove

the grease filters and set aside.

FIGURE 5

2. The rangehood mounts to the cabinet by two spring loaded

brackets, one on each side of the rangehood (FIGURE 6). Lift

the rangehood into the cutout opening in the cabinet. Be careful

not to damage the cabinet, rangehood or other appliances.

CUT-OUT

PREPARE THE CABINET

1. Disconnect and move freestanding range from cabinet

opening to provide easier access to upper cabinet and rear wall.

Put a thick, protective covering over cooktops, set-in ranges or

countertops to protect from damage or dirt.

2. Determine and clearly mark with a pencil the center line

of the cabinet on the wall and on the underside of the cabinet

where the rangehood will be installed.

3. If the cabinet bottom is recessed, wood blocks need to

be installed to insure proper alignment with the cabinet bottom.

Wood blocks should be ush or recessed 1/16" to 1/8" within

the cabinet bottom as indicated in FIGURE 4.

FIGURE 4

MAKE THE CUT-OUT OPENING (FIGURE 5)

WHERE THE RANGEHOOD WILL BE INSTALLED.

4. Determine the proper cutouts for the ductwork. Make all

necessary cuts in the walls or cabinets for the ductwork. Install

the ductwork before mounting the rangehood.

5. Determine and make the proper cutout for the Power Supply

Cable. Use a 1 1/4" Drill Bit to make this hole. Run the Power

Supply Cable through the wall or cabinet. DO NOT turn on the

power until installation is complete. Use caulking to seal around

the wire opening.

FIGURE 6

3.The spring loaded brackets are factory set to accomo-

date a thickness between 1 3/16" and 2 1/4". If your cabinet

bottom is less than 1 3/16" thick, the spring loaded brackets

can be removed and repositioned down from the top setting

to the bottom setting by removing the four phillips screws.

4. Tighten the rangehood to the cabinet by rotating the

screws with a phillips screw driver.

5. A grey vinyl strip (FIGURE 7) is included to cover the

underside of any remaining exposed cabinet. Attach the grey

vinyl strip to the bottom of the back of the rangehood with the

three screws provided. If necessary, the strip can be cut to

fit the cabinet depth.

7. Remove the cover from the eld wiring compartment with

a phillips screwdriver. Feed the Power Supply Cable through

the electrical knockout. Connect the Power Supply Cable to the

rangehood cable. Attach the White lead of the power supply

to the White lead of the rangehood with a twist-on type wire

connector. Attach the Black lead of the power supply to the

Black lead of the rangehood with a twist-on type wire connector.

Attach the Power Supply Cable grounding lead to the green

screw provided. Using the 4 holes provided, screw the eld

wiring compartment to the wall or cabinet as dictated by your

Power Supply Cable location (screws not provided). Replace

the cover.

8. Replace the grease lters. Connect the ductwork to the

damper and seal all connections.

9. Turn the power supply on. Turn on the blower and light.

If the rangehood does not operate, check that the circuit breaker

is not tripped or the house fuse blown. If the unit still does

not operate, disconnect the power supply and check that the

wiring connections have been made properly.

FIGURE 7

VINYL STRIP

25 1/2” - 31 1/2”

10”

25 1/2” - 31 1/2”

13/16”

17 1/2” - 23 1/2”

5 7/8”

Only for Ducted Venting Installation

Install the 2 Damper Flap included with the Range

Hood as shown.

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

Denomination

Lang EN Sheet

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

ELECTRICAL INSTALLATION WITH OPTIONAL

WIRING BOX

For Permanent wiring Installation-Use only with Listed

rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

GROUNDING INSTRUCTIONS This appliance must be grounded.

In the event of an electrical short circuit, grounding reduces the risk

of electric shock by providing an escape wire for the electric current.

This appliance is equipped with a cord having a grounding wire with

a grounding plug. The plug must be plugged into an outlet that is

properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualied electrician if the grounding instructions are not

completely understood, or if doubt exists as to whether the appliance

is properly grounded.

Do not use an extension cord. If the power supply cord is too short,

have a qualied electrician install an outlet near the appliance.

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/O Switch

TheOn/O switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light o.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower o.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut o when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is o, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The New Cristal comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9 .

FIGURE 8

15/32"

FIGURE 9

3/4"

7/8"

or 35

7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

ELECTRICAL INSTALLATION

WITH CONNECTION CABLE

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/O Switch

TheOn/O switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light o.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower o.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut o when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is o, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The New Cristal comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9 .

FIGURE 8

1 15/32"

FIGURE 9

3/4"

29 7/8" or 35 7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/O Switch

TheOn/O switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light o.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower o.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut o when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is o, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The New Cristal comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9 .

FIGURE 8

15/32"

FIGURE 9

3/4"

7/8"

or 35

7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/O Switch

TheOn/O switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light o.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower o.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut o when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is o, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The New Cristal comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9 .

FIGURE 8

15/32"

FIGURE 9

3/4"

7/8"

or 35

7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/O Switch

TheOn/O switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light o.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower o.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut o when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is o, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The New Cristal comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9 .

FIGURE 8

15/32"

FIGURE 9

3/4"

7/8"

or 35

7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

USE AND CARE INFORMATION

For Best Results

Start the rangehood several minutes before cooking to develop proper airow. Allow the

rangehood to operate for several minutes after cooking is complete to clear all smoke and

odors from the kitchen.

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/Off Switch

TheOn/Off switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light off.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower off.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut off when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

proper airow. Allow the unit to operate for several minutes

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

The metal grease lters should be cleaned frequently in hot

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

agents can scratch rangehood nishes and should not be

used to clean nished surfaces.

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is off, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The Cristal HC comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9.

FIGURE 8

1 15/32"

FIGURE 9

3/4"

29 7/8" or 35 7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

Version 06/14 - Page 8

USE AND CARE INFORMATION

Rangehood Control Panel

All controls are located on the right side of the rangehood.

Light On/Off Switch

TheOn/Off switch for the halogen light is located behind the

front trim. Moving the switch to the 1 Position turns the light

On. Moving the switch to the 0 position turns the light off.

Blower Speed Switch

B in FIGURE 10 shows the speed control switch for the

blower. Moving the switch to the 1 Position turns the blower

on LOW. Moving the switch to the 2 Position turns the blower

on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH. Moving the switch to the 0 Position turns

the blower off.

Automatic Operation

As long as the blower and light switches are on, the blower

and light will automatically operate when the visor is opened

and shut off when the visor is closed.

For Best Results

Start the rangehood several minutes before cooking to develop

proper airow. Allow the unit to operate for several minutes

after cooking is complete to clear all smoke and odors from

the kitchen.

Cleaning

The metal grease lters should be cleaned frequently in hot

detergent solution or placed in the dishwasher. Clean exterior

surfaces with hot soapy water. Using abrasives and scouring

agents can scratch rangehood nishes and should not be

used to clean nished surfaces.

Replacing the halogen lamp

CAUTION the bulb MAY BE HOT

To replace the halogen bulb, see (Figure 11)

Before attempting to replace the lamp, make sure the light

switch is off, the bulb CAUTION may be hot. Remove the

cover snap-on lamp levering under the metal ring, supporting

it with one hand. Remove the halogen lamp from the lamp

holder by pulling gently. Replace the lamp with a new one of

the same type, making sure that you insert the two pins into

the slots on the lamp holder. Replace the cover snap-on lamp.

FIGURE 10

FRONT TRIM OPTIONS

The Cristal HC comes with a stainless front strip installed.

Optional black and white strips are available as accessories

for purchase. To change the front strip, remove the three phil-

lips screws located behind the strip (FIGURE 8). If necessary,

the front strip can be adjusted by loosening the three phillips

screws and sliding the strip up or down. Tighten screws when

you have the strip properly placed.

For a custom front strip, a local cabinet shop can make a strip

to match your cabinets. The front strip dimensions are given

in FIGURE 9.

FIGURE 8

1 15/32"

FIGURE 9

3/4"

29 7/8" or 35 7/8"

Visor

Front

Strip

Three Screws

FIGURE 11

Cleaningmetalgreaselters

The metal grease lters can be cleaned in hot detergent solution or

washed in the dishwasher. They should be cleaned every 2 months

use, or more frequently if use is particularly heavy.

• Open the visor by pulling it.

• Remove the lter, pushing the lever towards the back of the unit and

at the same time pulling downward.

• Wash the lter without bending it, leave it to dry thoroughly before

replacing (if the surface of the lter changes color over time, this will

have absolutely no effect on its efciency).

• Replace, taking care to ensure that the handle faces forward.

• Cleaning in dishwasher may dull the nish of the metal grease

lter.

• Close

the visor.

Replacing Activated Charcoal Filter

The Activated Charcoal Filters are not washable and cannot

be regenerated, and must be replaced approximately every 4

months of operation, or more frequently with heavy usage.

• Open the visor by pulling it.

• Remove the Filter, pushing it towards the back of the unit and at the same

time pulling downward.

• Remove the saturated Activated Charcoal Filters, as indicated (A).

• Fit the new Filters, as indicated (B).

• Replace, taking care to ensure that the handle faces forwards.

• Close

the visor.

EN 7

INSTALLATION

Fitting the Hood canopy

BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:

• Disconnect the wires to the Commands at the connectors.

• Disconnect the wires to the Light at the con-

nectors.

• The Hood can be installed directly on the

underside of the wall unit (Minimum 650 mm

from the Cooker Hob).

• Create an opening in the bottom of the wall unit,

as shown.

• Insert the hood until the side supports snap into

place.

• Fasten using the 10 screws 12a provided.

• Lock in position by tightening the screws Vf from

underneath the hood.

• Open the suction panel by turning the specific knob.

• Disconnect the panel from the hood canopy by sliding the

fixing pin lever.

• Remove grease filters.

• Screw the Frame into place

using the 6 screws 12f, re-

connect the wires to the

Commands and Light, re-

place the metal grease filter

and the Panel.

260

495 - 675





Gu10 self-ballasted led

lamps – listed in ac-

cordance with

ul 1993/nmx-

j-578/1-ance/

csa c22.2 No.

1993

Lighting unit

• Turn off electrical supply before replacing bulbs, and

make sure bulbs are cool to touch before proceeding.

• Remove the lamp at the base and turn slightly to the

left and the pull out from the connector and turn slightly

to the left.

• Replace the lamp with a new one of the same type,

making sure that you insert the two pins properly into

the housings on the lamp holder.

• Once the bulb pins are in place turn slightly to the right

to secure.

Wiring Diagram

0123456789

H90_496 01

Drawing N : Rev :

Modif. by

Doc.status

Do not get quotas from the drawing do not bring

modifications without authorization of techincal office.

According to the law we reserve the own of the present

drawing with reproduction prohibition partial or total.

Approved date

Modification description

Approved by

WIRING DIAGRAM M8_4V SCL HV LED

Doc Type

Denomination

Creation date

02.Mar.2018

DOLCE CORRADO

Created by

991.0520.839

Code

LED

SW3

LED

CN3

RED (org)

VLT(org)

LB WH A GR

CN2

WHT

BRW

BLU

0 1 2 3

SW2

RED

123

654

789

PNK

BLU

PNK

BK BR

CN1

RED

BRW

SIDE

INSERT

CABLE

SW1

BLK

123

654

987

PNK

M8-4V

BRW

ORG

WHT

BLU

BLK

GRY

6,3uF

Y-G

WHT

220-240V ~ 50Hz

110-127V ~ 60Hz

220 ~ 60Hz

Y-G

BLK

WARRANTY

Franke Home Solutions Warranty for Franke and Faber Branded Product

Effective March 1, 2022

In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects

in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific

warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,

per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen

applications. Any products or components which have been modified or altered from their original intended condition will

void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-

transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are

obsolete or discontinued, or products that were previous display models. All issues with installed products are considered

warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product

reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product

and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original

purchase price.

The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from

misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper

installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by

impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct

the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct

house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses

or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with

electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or

repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or

non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and

transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /

Faber range hoods should always be serviced in the home in their original installation.

Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed

to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the

product replacements will be of similar size, material, and value. Any products or components which have been modified

or altered, from its original intended condition will void the warranty.

The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property

damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to

the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE

WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE

PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF

FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT

OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE

OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE

READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our

customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If

you do not agree with these terms and conditions, do not use this information. While we try to keep the information

current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify

information regarding Franke Kitchen Systems LLC programs and their use by you.

Franke / Faber Range Hood Limited Warranty:

Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a

period of two (2) years from the date of original purchase when used in standard residential indoor applications. This

warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components

necessary to restore the product to good working condition.

Franke Home Solutions Warranty for Franke and Faber Branded Product Effective March 1, 2022

In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects

in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific

warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed, per

Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen applications. Any

products or components which have been modified or altered from their original intended condition will void the Warranty.

The Franke Warranties for Faber branded products are limited to the original purchaser and are non- transferrable. These

Warranties do not include products purchased from non-Authorized Retailers, products that are obsolete or discontinued, or

products that were previous display models. All issues with installed products are considered warranty claims and not subject

to the Return Policy. Franke reserves the right to inspect any Franke / Faber product reported to be defective pursuant to a

Warranty claim and the original installation prior to providing a replacement product and/or component. All decisions are final.

In no situation shall the liability of Franke exceed the amount of the original purchase price.

The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from misuse

or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper installation, abnormal

usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by impurities, corrosive chemicals

or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct the installation of a range hood,

instructions on how to operate a range hood, to replace or repair house fuses or to correct house wiring or plumbing are not

covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses or filters and these consumable part

costs are also excluded from Warranty coverage. Installation not in accordance with electrical or plumbing codes or Franke

/ Faber documentation are not covered by any Warranty. Replacement parts or repair labor costs for units operated outside

the United States, Canada or Latin America, including any non-UL or C-UL or non-NOM approved Franke / Faber range hoods

are excluded from Warranty coverage. Expenses for travel and transportation for service in remote locations and pickup and

delivery charges are not covered by any Warranty. Franke / Faber range hoods should always be serviced in the home in their

original installation.

Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed to

be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the product

replacements will be of similar size, material, and value. Any products or components which have been modified or altered,

from its original intended condition will void the warranty.

The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property damage or

other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to the conditions set

forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE WARRANTIES SET

FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE PRODUCTS, INCLUDING, BUT

NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,

(3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF A

THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF

TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE

READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our customers.

By accessing and using this information, you agree to the following and to comply with all applicable laws. If you do not agree

with these terms and conditions, do not use this information. While we try to keep the information current, changes may have

occurred since its creation. Contact your Regional Manager or Customer Service to verify information regarding Franke Kitchen

Systems LLC programs and their use by you.

Franke / Faber Range Hood Limited Warranty:

Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a

period of two (2) years from the date of original purchase when used in standard residential indoor applications. This warranty

covers labor and replacement parts. Franke, at its option, may repair or replace the product or components necessary to

restore the product to good working condition.