Exterior Gate Exit Device and Trim
Installation Instructions
98/9952
252L
Customer Service
1-877-671-7011 us.allegion.com
*47269026*
47269026-00
© Allegion 2019
Printed in U.S.A.
47269026 Rev. 4/19-a
#10-24
Pour les instructions d’installation
en français, scannez le code QR sur
l’étiquette de l’emballage avec votre
smartphone. Cela permettra d’accéder
à des instructions d’installation
interactives spécialisées et à des
informations spéciques aux produits.
For the best installation experience, scan the QR code on the product box
label with your Smartphone.
This will give you access to specialized interactive installation instructions
as well as specic product information.
Digital Experience, Please Read!
1
2 3
54
Which way is your gate
handed?
Align push side template and
prepare holes and cutout
Remove templates from
shipping tube and separate.
If the gate is Left Hand Reverse (LHR),
the trim has to be rehanded as shown
in step 2.
If RHR, go to step 3.
If necessary, rehand trim from RHR to LHR
A. Remove Lower studs, cable mount, and spacer.
B. Remove retaining clip and set screw, cam, and shear pin.
C. Rotate lever 180 degrees to opposite side and reinstall
shear pin and cam.
D. Make sure cam is correct orientation. LHR will show “L”
on cam. You may need to push up on cable slider to
insert cam.
E. Reinstall set screw and retaining clip.
F. Put cable mount and spacer together.
G. Install lower studs.
A
B
C
Left Hand Reverse (LHR) shown
Right Hand Reverse (RHR) opposite
Right Hand Reverse (RHR)
Left Hand Reverse (LHR)
PUSH
SIDE
PULL
SIDE
D
A. Mark trim centerline 54” from
bottom of gate.
B. Align template and mark holes.
C. Prepare holes and cutout.
Cut on bold dotted line
between Push and Pull side
templates.
NOTE: If required for retrot,
additionally cut Push side
template on thin dotted line
(Reduce by no more than 2”).
Install cylinder into trim
54"
36" to
bottom
of gate
18" between
trim and
exit device
centerlines
Gate edge
for Push
side RHR
Gate edge
for Push
side LHR
Vertical
Cable
Vertical
Cable
4x drill and tap
#10-24 UNC 2B
thru one wall
Exit
Device
2x Ø .196 thru
Ø .385 x 82°
4x Ø .375
thru one wall
Trim
Remove
material
(one wall)
PUSH
SIDE
TEMPLATE
8
9
6
7
Align pull side template and
prepare holes and cutout
Attach other end of cable to center slide
Slide trim assembly into pull side of door
Attach cable to trim
A. Mark trim centerline 54” from
bottom of gate.
B. Align template and mark holes.
C. Prepare holes and cutout.
Remove
material
(one wall)
2x Ø .375
thru one wall
Trim
54" to
bottom
of gate
Trim
PULL
SIDE
TEMPLATE
Vertical
Cable
54"
14
15
16
10
11
12 13
Install end cap bracket and
end cap
If necessary, cut the exit device
Install the lift nger parts
Start screws but do not tighten.
Secure trim with 4 screws
and washers
Secure center slide with 2
screws
Check clearance for end cap
Attach center case to gate
1.5”
min.
The 4 main screws are required.
The 2 security screws are optional.
Clearance should be 1.5” minimum.
If clearance is less, you will need to cut
the exit device.
Temporarily remove
anti-rattle clip
Cover plate flush
17
18
19 20
21
Install center case cover
Adjust the lift nger
Install strike support screws
Install strike along center line on
post and adjust as needed
A. Hold the trim lever down during adjustment.
B. Loosen retaining screw.
C. Turn the bottom adjusting screw clockwise until latchbolt retracts fully.
D. Tighten retaining screw.
Remove adhesive and place along
center line of post. The surface should
be free from grease and debris to
ensure a good bond.
There should be a 3/16” gap between the
center case cover and the strike roller.
A
B
C
C
3/16”
Install Latchbolt rub plate
23
22
Test door function
A. Use key in cylinder to lock and unlock
the trim, verifying locking function.
B. Press the pushpad on the exit device
and verify that the gate opens properly.
C. With trim unlocked, pull down on the
lever and verify that gate opens properly.
If the product does not function as
expected, re-check the installation steps,
or call Customer Service at:
1-877-671-7011
Cable Removal
(If the cable was installed in wrong
position)
A cable removal tool was included with
device. Slot in tool ts over cable, holding
tabs down. Pull on cable
snap to loosen cable
for removal.
slot
cable
snap
b
a
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
