Yamaha EAD10 Drum Module Manuel utilisateur

Catégorie
Batterie de musique
Taper
Manuel utilisateur

Ce manuel convient également à

Owners Manual
Electronic Acoustic
Drum Module
EN
Quick Guide
Features of the EAD10
page 6
page 10
S-1
EAD10 Owner’s Manual
For EAD10
This product utilizes batteries or an external power supply (adapter).
DO NOT connect this product to any power supply or adapter other
than one described in the manual, on the name plate, or specifically
recommended by Yamaha.
WARNING: Do not place this product in a position where anyone
could walk on, trip over, or roll anything over power or connecting
cords of any kind. The use of an extension cord is not recommended!
If you must use an extension cord, the minimum wire size for a 25’
cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the
larger the current handling capacity. For longer extension cords, con-
sult a local electrician.
This product should be used only with the components supplied or; a
cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is
used, please observe all safety markings and instructions that accom-
pany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at
the time of printing. However, Yamaha reserves the right to change or
modify any of the specifications without notice or obligation to update
existing units.
This product, either alone or in combination with an amplifier and
headphones or speaker/s, may be capable of producing sound levels
that could cause permanent hearing loss. DO NOT operate for long
periods of time at a high volume level or at a level that is uncomfort-
able. If you experience any hearing loss or ringing in the ears, you
should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
Some Yamaha products may have benches and / or accessory mount-
ing fixtures that are either supplied with the product or as optional
accessories. Some of these items are designed to be dealer assem-
bled or installed. Please make sure that benches are stable and any
optional fixtures (where applicable) are well secured BEFORE using.
Benches supplied by Yamaha are designed for seating only. No other
uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a
function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the
owners responsibility. Please study this manual carefully and consult
your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and envi-
ronmentally friendly. We sincerely believe that our products and the
production methods used to produce them, meet these goals. In keep-
ing with both the letter and the spirit of the law, we want you to be
aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if
applicable) is soldered in place. The average life span of this type of
battery is approximately five years. When replacement becomes nec-
essary, contact a qualified service representative to perform the
replacement.
This product may also use “household” type batteries. Some of these
may be rechargeable. Make sure that the battery being charged is a
rechargeable type and that the charger is intended for the battery
being charged.
When installing batteries, never mix old batteries with new ones, and
never mix different types of batteries. Batteries MUST be installed cor-
rectly. Mismatches or incorrect installation may result in overheating
and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all bat-
teries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of
household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some rea-
son its useful life is considered to be at an end, please observe all
local, state, and federal regulations that relate to the disposal of prod-
ucts that contain lead, batteries, plastics, etc. If your dealer is unable
to assist you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model
number, serial number, power requirements, etc., are located on this
plate. You should record the model number, serial number, and the
date of purchase in the spaces provided below and retain this manual
as a permanent record of your purchase.
Model
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
SPECIAL MESSAGE SECTION
92-BP (bottom)
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Electronic Acoustic Drum Module
Model Name : EAD10
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC)
S-2
EAD10 Owner’s Manual
For AC adaptor and EAD10
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
FCC INFORMATION (U.S.A.)
S-3
EAD10 Owner’s Manual
For AC adaptor
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
(can_b_02)
CAN ICES-3 (B)/NMB-3(B)
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral trian-
gle is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the manu-
facturer.
12 Use only with the cart, stand, tri-
pod, bracket, or table specified by
the manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13 Unplug this apparatus during light-
ning storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
S-4
EAD10 Owner’s Manual
(standby)
(weee_eu_en_02)
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der
er slukket på apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection
points, in accordance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old products, please contact your local municipality,
your waste disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
2
EAD10 Owner’s Manual
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
This AC adaptor is designed for use with only Yamaha electronic instruments. Do
not use for any other purpose.
Indoor use only. Do not use in any wet environments.
CAUTION
When setting up, make sure that the AC outlet is easily accessible. If some trouble
or malfunction occurs, immediately turn off the power switch of the instrument and
disconnect the AC adaptor from the outlet. When the AC adaptor is connected to
the AC outlet, keep in mind that electricity is flowing at the minimum level, even if
the power switch is turned off. When you are not using the instrument for a long
time, make sure to unplug the power cord from the wall AC outlet.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting,
damages, fire or other hazards. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or radiators. Also,
do not excessively bend or otherwise damage the cord, or place heavy objects on
it.
Only use the voltage specified as correct for the instrument. The required voltage is
printed on the name plate of the instrument.
Use the specified adaptor (page 63) only. Using the wrong adaptor can result in
damage to the instrument or overheating.
Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
This instrument contains no user-serviceable parts. Do not open the instrument or
attempt to disassemble or modify the internal components in any way. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected by
qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as water
seeps into the instrument, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the instrument inspected by qualified Yamaha
service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
When one of the following problems occur, immediately turn off the power switch
and disconnect the electric plug from the outlet. Then have the device inspected by
Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
For AC adaptor
For EAD10
Power supply/AC adaptor
Do not open
Water warning
Fire warning
If you notice any abnormality
DMI-5 1/2
3
EAD10 Owner’s Manual
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other
property. These precautions include, but are not limited to, the following:
Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
When removing the electric plug from the instrument or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
Remove the electric plug from the outlet when the instrument is not to be used for
extended periods of time, or during electrical storms.
Read carefully the attached documentation explaining the assembly process.
Failure to assemble the instrument in the proper sequence might result in damage
to the instrument or even injury.
Do not place the instrument in an unstable position where it might accidentally fall
over.
Before moving the instrument, remove all connected cables, to prevent damage to
the cables or injury to anyone who might trip over them.
When setting up the product, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is
turned off, electricity is still flowing to the product at the minimum level. When you
are not using the product for a long time, make sure to unplug the power cord from
the wall AC outlet.
Use the included module holder if you are installing the EAD10 on the hi-hat stand.
Also, make sure you use the wing bolts included with the module holder. Failure to
do so could cause damage to the internal components or result in the instrument
falling over.
Be sure to securely tighten the clamp screw and module holder wing bolts when
setting up the EAD10. Also, do not loosen the clamp screw or module holder wing
bolts rapidly. Not doing so can cause parts to fall off the main unit, sensor unit, or
module holder resulting in injury.
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components,
set all volume levels to minimum.
Be sure to set the volumes of all components at their minimum levels and gradually
raise the volume controls while playing the instrument to set the desired listening
level.
Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
Do not use the instrument/device or headphones for a long period of time at a high
or uncomfortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
Always turn the power off when the instrument is not in use.
Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.
When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.
Power supply/AC adaptor
Assembly
Location
Connections
Handling caution
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
DMI-5 2/2
4
EAD10 Owner’s Manual
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage
to data, or damage to other property, follow the notices below.
Handling
Do not use the instrument in the vicinity of a TV, radio, stereo equip-
ment, mobile phone, or other electric devices. Otherwise, the
instrument, TV, or radio may generate noise. When you use the
instrument along with an application on your iPad, iPhone or iPod
touch, we recommend that you set “Airplane Mode” to “ON” on that
device in order to avoid noise caused by communication.
Do not expose the instrument to excessive dust or vibrations, or
extreme cold or heat (such as in direct sunlight, near a heater, or in
a car during the day) to prevent the possibility of panel disfiguration,
damage to the internal components or unstable operation.
Do not place vinyl, plastic or rubber objects on the instrument,
since this might discolor the panel or keyboard.
Maintenance
When cleaning the instrument, use a soft and dry/slightly damp
cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids,
or chemical-impregnated wiping cloths.
Saving data
System settings (Reference Manual (Advanced)(PDF)) are stored
automatically and will not be lost when the power is turned off.
However, settings may be lost due to malfunction or improper oper-
ation. Save important data to an external device such as a USB
flash drive or a computer (pages 25 and 30). Please read page 30
before using a USB flash drive.
Edits to Scenes, etc., are lost if not saved before the power is
turned off. Likewise, edits are lost when the auto power off function
turns the power off (page 29). Save data you want to keep to the
main unit, or to an external device such as a computer or USB flash
drive (pages 25 and 30). However, data stored in the main unit may
be lost due to malfunction or improper operation. Save important
data to an external device such as a USB flash drive or a computer
(pages 25 and 30). Please read page 30 before using a USB flash
drive.
To protect against data loss through USB flash drive damage, we
recommend that you save your important data onto spare USB
flash drive or an external device such as a computer as backup
data.
Information
About copyrights
Copying of the commercially available musical data including but
not limited to MIDI data and/or audio data is strictly prohibited
except for your personal use.
This product incorporates and bundles contents in which Yamaha
owns copyrights or with respect to which Yamaha has license to use
others’ copyrights. Due to copyright laws and other relevant laws,
you are NOT allowed to distribute media in which these contents
are saved or recorded and remain virtually the same or very similar
to those in the product.
* The contents described above include a computer program, Accompani-
ment Style data, MIDI data, WAV data, voice recording data, a score, score
data, etc.
* You are allowed to distribute medium in which your performance or music
production using these contents is recorded, and the permission of Yamaha
Corporation is not required in such cases.
About this manual
The illustrations and LCD screens as shown in this manual are for
instructional purposes only, and may appear somewhat different
from those on your instrument.
Windows is a registered trademark of Microsoft® Corporation in the
United States and other countries.
MacOS, iPhone and iPad are trademarks of Apple Inc., registered
in the U.S. and other countries.
The company names and product names in this manual are the
trademarks or registered trademarks of their respective companies.
The names of buttons, terminals, and the like from the EAD10’s
front, rear and top panels are enclosed in [ ] (square brackets).
Latest Firmware Version
From time to time, Yamaha may update product firmware without
prior notice.
We recommend, therefore, that you check our web site (below) for
the latest version and keep your EAD10 firmware up to date.
http://download.yamaha.com/
The content of this Owner’s Manual applies to the newest version of
the firmware as of printing. Details regarding any functions added to
later versions will also be made available via the above web site.
About the Pads
Within this Owner’s Manual, the optional external pads that may be
connected to the EAD10 are referred to by model name. Please note
that these model names were up-to-date as of printing of this man-
ual.
Details regarding any subsequently released models will be made
available via the following web site.
http://download.yamaha.com/
* Yamaha Corporation reserves the right to modify this URL at any
time without prior notice.
5
EAD10 Owner’s Manual
(bottom_en_01)
The model number, serial number, power requirements, etc., may be found on or near the
name plate, which is at the bottom of the unit.
You should note this serial number in the space provided below and retain this manual as a
permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
6
EAD10 Owner’s Manual
Quick Guide
Adjusting Volume and Sound Balance (page 13)
1.
Turn the [MASTER VOLUME] knob or [AUDIO/
CLICK VOLUME] knob.
Hit all drums and cymbals in the drum set to make sure
that the EAD10 is picking up the sound.
Changing Sounds (page 33)
1.
Turn the [SCENE] knob to select different
sounds (Scenes).
2.
Adjust the levels with the [REVERB],
[EFFECT], and [TRIGGER] knobs.
Practicing with the Metronome (Click) (page 39)
1.
Press the [ ] (Click) button.
2.
Press the button below “ ” to the start the
Metronome.
3.
Use the [+] or [–] buttons to adjust the tempo.
4.
Press the “ ” button again to stop the Metro-
nome.
1
Overall volume Volume control for the AUX
IN (auxiliary input) and Met-
ronome (click)—sounds
other than what you play
2
1
Adjusts the
Reverb depth
Adjusts the Trigger Sound
volume (with the default
setting, the Trigger sound is
added to the bass drum)
Adjusts the
Effect depth
132, 4
7
EAD10 Owner’s Manual
Quick Guide
Playing Along with a Favorite Song (page 24)
1.
Connect a portable music player to the [AUX
IN] jack.
2.
Start music playback on your portable
player.
3.
Play the drums while listening with head-
phones.
Recording Your Performance (page 41)
1.
Press the [RECORDER] button.
2.
Press the button below “” to start record-
ing.
3.
Play the drums.
4.
Press the button below “ ” to stop record-
ing.
2
1
3
12, 4
3
8
EAD10 Owner’s Manual
PRECAUTIONS 2
Quick Guide 6
Included Accessories 9
Features of the EAD10 10
How the EAD10 makes sound........................................... 11
About the Manuals 12
Printed Manual .................................................................. 12
Digital Manual (PDF) ......................................................... 12
Panel Controls and Functions 13
Main Unit ........................................................................... 13
Sensor Unit........................................................................ 15
About the Trigger Input Jacks............................................ 16
Setup Guide 17
Setting Up.......................................................................... 17
Connect with Other Devices and Expand the Fun............. 24
Turning On or Off............................................................... 25
Setting Up the Sensor Unit ................................................ 27
Changing the Overall Settings........................................... 29
Using a USB Flash Drive................................................... 30
Basic Guide 32
Performing with Various of Scenes ................................... 32
Creating Your Own Scene................................................. 35
Using the Click (Metronome) ............................................. 39
Recording Your Performance............................................ 41
Application Guide 48
Enhance Your Drum Set with Separately Sold Add-Ons... 48
Reference 55
Menu List........................................................................... 55
Troubleshooting................................................................. 58
Message List ..................................................................... 61
Specifications .................................................................... 63
Index.................................................................................. 64
Contents
9
EAD10 Owner’s Manual
Welcome
Thank you for purchasing this Yamaha product.
To get the most out of your EAD10, be sure to read this Owner’s Manual carefully.
And after reading through this manual, be sure to store it in a safe place
so that you can refer back to it again as needed.
Included Accessories
Owner’s Manual (this book)
AC adaptor
Module holder
Module holder wing bolts (× 2)
Connector cables (1 pair)
Cable bands (× 3)
Adhesive cushions (× 2)
10
EAD10 Owner’s Manual
Features of the EAD10
The EAD10 lets you easily change the sound of your acoustic drums into the sound of your liking.
Connect a smart phone to the EAD10 and enjoy playing the drums along with your favorite music.
Also, it can be used in a wide range of applications from practice, recording to live situations.
Sensor Unit that mounts on the bass drum makes setup simple
Built-in XY configured stereo mic provides high quality monitoring of the entire drum set with natu-
ral balance and stereo orientation
Loud drums can be monitored with proper volume using headphones or earphones
Change effect settings with a single knob and easily save and recall settings
PCM tone generator makes it easy to change the sound of your bass drum by using a Triggered
sound — even in the middle of a performance
Play a wide range of musical genres from contemporary to the by using the effects, your own sam-
ples or the internal Triggered sounds
Recording and playback possible via USB flash drive or USB audio
Left and right outputs allow you to easily connect to a PA
Easy setup allows comfortable monitoring of your drum sound while playing
Transforms the sound of your drums into a sound of your liking
Use for recording or in-live situations
11
EAD10 Owner’s Manual
How the EAD10 makes sound
The Sensor Unit sends two types of signals to the Main Unit; an audio signal captured with the mic
sensor, and a trigger signal captured with the trigger sensor.
The audio signal can be processed with Effects, while the trigger sensor can be used to play Trigger
Sounds depending on how you play your drums.
For more information on Trigger Sounds, Effects, and Reverb, please see “What is a Scene?” (page
32).
Mic sensor
Trigger sensor
Audio signal from
the drum set
Trigger signal from
the bass drum
(Mic sound &)
Effects
Trigger Sound
(internal Voices)
Reverb
Sensor Unit
Main Unit
12
EAD10 Owner’s Manual
About the Manuals
The following manuals are provided for using the EAD10. These manuals are intended for users
of the EAD10.
Owners Manual (this book)
Setup Guide
Explains how to attach and setup the EAD10 for producing sound.
Basic Guide
Describes the fundamentals needed to operate the EAD10.
Application Guide
Describes parameter settings and other more advanced uses.
Reference
Describes troubleshooting techniques and contains other reference materials.
Reference Manual (Advanced)
The Reference Manual provides a description of all of the functions that can be accessed by pressing the [MENU] but-
ton.
Data List
This provides lists of Scene and Effect names in the EAD10, and MIDI related information.
iPhone/iPad Connection Manual
Describes how to connect smart devices such as an iPhone and iPad.
Printed Manual
Digital Manual (PDF)
The digital format manuals listed above can be obtained from the Yamaha Downloads web page.
To do so, go to the web page using the following URL, enter “EAD10” in the “Model Name”
field, and then click “Search.
Yamaha Downloads: http://download.yamaha.com/
13
EAD10 Owner’s Manual
Panel Controls and Functions
Main Unit
Top Panel
[AUDIO/CLICK VOLUME] knob
Adjusts the volume for AUX IN (aux-
iliary input) and Click functions—any
sound or audio you play along to.
Function Buttons 1–3
(page 33) ([F1], [F2], [F3])
Selects the functions that
appear at the bottom of each
screen.
Display (page 33)
Displays a variety of informa-
tion.
[SCENE] knob (page 33)
Switches between the dif-
ferent sound sets.
Or, returns to the Scene
screen from other screens.
NOTE
The knob can be used in the same manner as the
[–] and [+] buttons. For more information, refer to the
Reference Manual (Advanced) (PDF) (MENU/Utility/
General).
[ ] (Standby/On) switch (page 25)
Switches the power between standby (off) and
on.
[MENU] button
Accesses the advanced settings
screen. For more detailed informa-
tion, refer to the Reference Manual
(Advanced) (PDF).
[REVERB] knob (page 33)
Adjusts the reverb level.
[EFFECT] knob (page 33)
Adjusts the amount of Effect applied to the
audio signal from the mic sensor.
[TRIGGER] knob (page 33)
Adjusts the Trigger Sound volume.
[STORE] button (page 37)
Opens the Store screen. Stores Scenes
that you have created.
[–] button,
[+] button
Increases or
decreases the
value by one (1).
[ ] (Click) button (page 39)
Accesses the Click (Metronome)
screen. The button flashes in
sync with the Click tempo.
[RECORDER] button (page 41)
Accesses the Recorder (record/play-
back) screen. The button lights while
recording or during playback.
[EXIT] button
Cancels the action, or returns to the screen one level higher.
Press several times to return to the Scene screen.
NOTE
When in the Scene Screen, this button can also be used as a
Panic Button to stop any sounds.
[ ] (Sensor Unit) button
(page 27)
Accesses the Sensor Unit
screen. Set the mic sensor level
so that the button occasionally
flashes when hitting the drums
strongly.
[MASTER VOLUME] knob
Adjusts the overall volume.
14
EAD10 Owner’s Manual
Panel Controls and Functions
Rear Panel
[FOOT SW] Jack (page 48)
Connects a foot pedal or foot switch (sold sep-
arately).
FC5 HH65
etc.
FC7
TO SENSOR UNIT [A] jack
(page 17)
Connect to the [A] jack on the
Sensor Unit using the connec-
tor cable (included).
TO SENSOR UNIT [B] jack
Connect to the [B] jack on the
Sensor Unit.
For more information on the [qKICK/w]
to [y] jacks, see “About the Trigger Input
Jacks” (page 16).
Sensor Unit
Standard phone plug
(6.3 mm)
Stereo mini plug
(3.5 mm)
DC IN jack (page 17)
Use the AC adaptor that
came with the EAD10.
USB cable
[USB TO DEVICE] termi-
nal (page 30)
Connects a USB flash
drive.
Cannot be used with other
USB devices.
[USB TO HOST] terminal (page 25)
Connect a computer or smart device
such as an iPhone or iPad to send and
receive digital signals (audio and MIDI).
Additional parts are required for connect-
ing an iPhone or iPad. For more informa-
tion, refer to “iPhone/iPad Connection
Manual” (PDF).
Cord hook (page 17)
Wrap the AC adaptor cord
around this hook to prevent
accidental unplugging dur-
ing use.
Cord hook
AC adaptor cord
[AUX IN] (auxiliary
input) jack
(page 17)
Connect to the
headphone jack on
a smart phone or
portable music
player.
OUTPUT [R]/[L/MONO]
jacks (page 17)
Connect to powered speak-
ers or other such PA system.
These jacks are standard
phone type output jacks.
If mono output is required,
use only the [L/MONO] jack.
15
EAD10 Owner’s Manual
Panel Controls and Functions
Front Panel
Sensor Unit
NOTICE
Do not hit the Sensor Unit with the drumsticks. Doing so can damage the mic sensor resulting in inferior performance.
Standard stereo phone plug
(6.3 mm)
[PHONES] jack
Connects headphones. This output jack is a standard
stereo phone plug (6.3 mm). Use a 3.5 mm stereo
mini to (6.3 mm) stereo adaptor to connect head-
phones or earphones with a stereo mini plug (3.5 mm)
to the [PHONES] jack.
CAUTION
Do not use headphones for a long period of time at
high volume. Doing so can cause loss of hearing.
Mic Sensor
Captures the whole drum set’s
acoustic sound converting it into
an audio signal.
[A] jack
Connect to the TO SENSOR UNIT
[A] jack on the rear panel using
the connector cable (included).
Sends the trigger sensor signal.
[B] jack
Connect to the TO SENSOR UNIT
[B] jack on the rear panel using
the connector cable (included).
Sends the mic sensor signal.
Clamp screw (page 17)
Secures the Sensor Unit to
the bass drum hoop.
Trigger sensor
Converts vibrations produced
when the bass drum is hit
into a trigger signal.
16
EAD10 Owner’s Manual
Panel Controls and Functions
Trigger signals are received via the trigger input jacks. These are used for connecting separately sold accessories to the
EAD10. You can connect up to six pads or drum triggers.
[qKICK/w] through [y] jacks are located on the rear panel of the Main Unit.
Visit the web page below for more information on separately sold accessories that can be connected to each trigger input
jack.
For more information on connections of separately sold accessories, see “Enhance Your Drum Set with Separately Sold
Add-Ons” (page 48).
Yamaha Downloads: http://download.yamaha.com/
* Yamaha Corporation reserves the right to modify this URL at any time without prior notice.
About the Trigger Input Jacks
Standard stereo phone plug
(6.3 mm)
Trigger Input jacks
[qKICK/w]
The TO SENSOR UNIT [A] jack can
be as the [qKICK/w] jack (page 48).
This jack consists of a pair of mono
trigger inputs.
[eSNARE/r]
This jack consists of a pair of mono
trigger inputs. Connects drum triggers
such as the DT50S (sold separately)
(page 48).
DT50S
[t] and [y]
Connects DTX Series pads, etc.
(page 48).
Supports three-zone pads.
TP70S
XP80
PCY135
Using a commercially available Y-cable you
can connect two mono pads.
For example, you can connect a Sensor Unit
and a kick pad to the [qKICK/w] jack.
Stereo audio plug
Mono phone jack
Mono phone jack
Y-cable
KU100
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Yamaha EAD10 Drum Module Manuel utilisateur

Catégorie
Batterie de musique
Taper
Manuel utilisateur
Ce manuel convient également à