Maytag MVWB766FW MVWB766FW Use and Care EN

Marque: Maytag

Modèle: MVWB766FW

Catégorie: Machines à laver

Taper: MVWB766FW Use and Care EN

W10911450A

W10911466A-SP

Designed to use only

HE High Efﬁciency detergents.

Conçue pour l’utilisation d’un

détergent haute efﬁcacité seulement.

If you have any problems or questions, visit us at www.maytag.com

Pour tout problème ou tout question, consulter www.maytag.ca

Use & Care Guide

Guide d’utilisation et d’entretien

Top-Loading High Efﬁciency Washer

Laveuse haute efﬁcacité avec chargement par le dessus

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.maytag.com.

WASHER SAFETY

Table of Contents

WASHER SAFETY ...................................................................2

WHAT’S NEW UNDER THE LID? .........................................4

CONTROL PANEL AND FEATURES ....................................5

CYCLE GUIDE ...........................................................................7

USING YOUR WASHER .........................................................9

WASHER MAINTENANCE ...................................................12

TROUBLESHOOTING ...........................................................14

WARRANTY ............................................................................19

ASSISTANCE OR SERVICE ..........................BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ...............................................20

QUOI DE NEUF SOUS LE COUVERCLE? .......................21

TABLEAU DE COMMANDE ET

CARACTÉRISTIQUES ...........................................................22

GUIDE DE PROGRAMMES .................................................25

UTILISATION DE LA LAVEUSE ..........................................27

ENTRETIEN DE LA LAVEUSE .............................................30

DÉPANNAGE ..........................................................................32

GARANTIE ...............................................................................38

ASSISTANCE OU SERVICE ......COUVERTURE ARRIÈRE

For best performance, it is recommended to load items in loose

heaps evenly around the agitator.

As the washer dampens and moves the load, the level of the

items will settle in the basket. This is normal, and does not

indicate that more items should be added.

WHAT’S NEW UNDER THE LID?

Choosing the Right Detergent

Use only High Efﬁciency detergents. The package will be marked

“HE” or “High Efﬁciency.” High Efﬁciency wash systems create

excessive sudsing with a regular non-HE detergent. Using regular

detergent will likely result in longer cycle times and reduced

rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce

the right amount of suds for the best performance. Follow the

manufacturer’s instructions to determine the amount of detergent

to use and do not go over the Max line on the dispenser. See

“Using Laundry Product Dispensers” for more information.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds and

noises that are different from those of your previous washer. For

example, you may hear a clicking and hum at the beginning of the

cycle as the lid lock goes through a self-test. There will be different

kinds of humming and whirring sounds as the agitator moves the

load and as the basket is slowing down to stop. Sometimes, you

may hear nothing at all as the washer determines the correct water

level for your load or allows time for clothes to soak.

Use only High Efﬁciency (HE) detergent.

More Water When You Need It

The most striking difference in your new washer is the Dual

Wash Agitator System. In Auto-Sensing Water Level mode,

the washer automatically adjusts the water level to the optimal

amount for a High Efﬁciency wash of the detected load size. In

Deep Fill mode, the washer will ﬁll to a pre-determined water level

independent of load size, allowing for greater ﬂexibility in how you

wash your clothes.

Traditional Low-Water

Wash System

Low-Water Wash System

With Deep Fill Wash Mode

Washplate

Automatic Load Size Sensing

Once you start the cycle, the lid will lock, and the washer will begin

the sensing process to determine the correct water level for the

load. This may take several minutes before water is added. You will

ﬁnd a step-by-step description in the “Cycle Status Lights” section.

Initially the basket will start to spin prior to adding water, this is part

of the sensing process and is normal.

Deep Fill

Wash

Low Water

Wash

Agi-Peller

Dual Wash

System

Dual Wash

Agitator System

Auto-Sensing

Water Level

Deep Fill

WashplateWashplate

CONTROL PANEL AND FEATURES

POWER

Touch to turn the washer on and off. Touch to stop/cancel a

cycle at any time.

WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on your

washer. Turn the knob to select a cycle for your laundry load.

See “Cycle Guide” for detailed descriptions.

ESTIMATED CYCLE TIME

The Estimated Cycle Time display shows the time required for

the cycle to complete. Factors such as load size and water

pressure may affect the time shown in the display. Overloading,

unbalanced loads, or excessive suds may cause the washer to

adjust the cycle time, as well.

DELAY START

Use “+” and “–” to delay the start of the wash cycle by up to

12 hours. To turn off Delay Start, use “+” and “–” to set the

delay time to “0,” or touch POWER.

START/PAUSE BUTTON

Touch and hold START/PAUSE button for up to 3 seconds or

until the washer starts to begin the selected cycle. To pause a

cycle after it has started, press the START/PAUSE button again.

NOTE: If the washer is spinning, it may take several minutes

to unlock the lid.

CYCLE MODIFIERS

The following options may be added to most cycles.

TEMPERATURE

Wash temperature senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following the

garment label instructions, use the warmest wash water safe

for your fabric.

• On some models and cycles, warm and hot water may be

cooler than your previous washer.

• Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

SOIL LEVEL

Select the most suitable setting for your load. For heavily

soiled items, select Extra Heavy Soil Level for more wash

time. For lightly soiled items, select Extra Light Soil Level

for less wash time.

Lighter soil level setting will help reduce tangling

and wrinkling.

SPIN SPEED

Select the most suitable setting for your load.

CYCLE OPTIONS

The following options may be added to most cycles.

OXI

This washer is designed to dispense laundry boosters such

as oxygenated stain treaters and color-safe bleach at the

right time in the cycle for best cleaning performance. Do not

use laundry boosters and chlorine bleach in the same cycle.

EXTRA RINSE

This option can be used to automatically add a second rinse

to most cycles.

NOTE: If you want to Rinse and Spin, select the Drain & Spin

cycle; then touch to turn on the Extra Rinse option.

DEEP CLEAN w/Steam (depending on model)

This option adds additional soak and wash time to many

cycles to help remove tough stains, as well as a steam

boost for added cleaning power. Deep Clean w/Steam

uses a heater within the washer to maintain the selected

temperature setting throughout the wash period. Deep Clean

w/Steam may be selected as an option with other cycles.

DEEP CLEAN (depending on model)

This option provides enhanced cleaning action for tough

stains. It will add additional agitation and soak time to the

cycle.

AUDIO LEVEL

Use this option to adjust volume of the signal that sounds at

the end of cycle and key pad sounds. Touch once for low, a

second time for off, and a third time to loop back to high. A

higher signal is helpful in removing items as soon as cycle is

complete. Default setting is high.

CYCLE STATUS LIGHTS

The Cycle Status Lights show the progress of a cycle. At each

stage of the process, you may notice sounds or pauses that are

different from traditional washers.

SENSING

When the START/Pause button is touched, the washer will

ﬁrst perform a self-test on the lid lock mechanism. You will

hear a click, the basket will make a slight turn, and the lid will

unlock brieﬂy before locking again.

Once the lid has locked the second time, the washer will use

short, slow spins to estimate the load size. These sensing

spins may take 2 to 3 minutes before water is added to the

load and you may hear the hum of these spins. If the sensing

light is on, then washer is working properly. You will hear the

NOTE: The control panel features a sensitive surface that responds to a light touch of your ﬁnger. To ensure your selections are registered,

touch the control panel with your ﬁnger tip, not your ﬁngernail. When selecting a setting or option, simply touch its name until the desired

section is illuminated.

motor turn the basket in short pulses to thoroughly wet the

load. The washer will then move the load brieﬂy, pause to

allow water to soak in to the load, and resume adding water.

This process may repeat until the correct amount of water

has been added for the load. You may also hear water ﬂowing

through the dispenser, adding detergent to the load.

NOTE: Avoid opening lid during sensing. The sensing

process will start over when the washer is restarted. The

sensing light may also come on during the Wash portion of

the cycle. This is normal.

WASH

You will hear the motor and agitator moving the load. Unlike

traditional washers, the load is not covered with water. Rather

than diluting detergent as done in an agitator-style washer,

this washer delivers the detergent directly to the soils. The

motor sounds may change at different stages in the cycle.

The wash time is determined by the selected soil level.

RINSE

You will hear sounds similar to the wash cycle as the washer

rinses and moves the load. Fabric softener will be added if

the Timed Dispensers Fabric Softener option was selected.

SPIN

The washer spins the load at increasing speeds for proper

water removal, based on the selected cycle and spin speed.

DONE

Once the cycle is complete, this light will come on. Remove

the load promptly for best results.

LID LOCKED

To allow for proper load sensing and spinning,

the lid will lock and the Lid Locked light will turn

on. This light indicates that the lid is locked and

cannot be opened.

If you need to open the lid, touch START/Pause.

The lid will unlock once the washer movement

has stopped. This may take several minutes if the load

was spinning at high speed. Touch and hold START/

PAUSE button again for up to 3 seconds to restart the

cycle.

Avoid opening the lid during sensing. The sensing

process will start over when the washer is restarted.

DEEP FILL & AUTO SENSING WATER LEVEL

STATUS LIGHTS

DEEP FILL

The Deep Fill mode is OFF by default but can be turned

on for any cycle except Sanitize with Oxi & Steam or

Sanitize with Oxi (depending on model), Drain & Spin,

and Clean Washer.

When selecting Deep Fill, the Deep Fill light will turn on

and the Auto Sensing Water Level Status Lights will

turn off.

In Deep Fill mode, the washer will ﬁll to a pre-determined

water level independent of load size, allowing for greater

ﬂexibility in how you wash your clothes.

AUTO SENSING WATER LEVEL STATUS LIGHTS

When the machine is operating in Low Water Wash mode

(Deep Fill is OFF), these status lights provide feedback

on the load size that has been detected. When powering

up the unit in Low Water Wash mode, all three lights will

be lit. The lights will remain lit until the Sensing portion of

the cycle is complete. The machine will now illuminate the

light reﬂecting the detected load size.

NOTE: These lights only function when Deep Fill mode

is OFF.

Dispensers

Liquid fabric softener dispenser

Pour measured liquid fabric softener into the liquid fabric

softener dispenser if desired. It will dispense automatically

at the optimum time.

•

Use only liquid fabric softener in this dispenser.

High Efﬁciency “HE” detergent dispenser

Add liquid or powdered HE detergent product to this

dispenser for your main wash cycle. Remove tray if using

powder detergent.

IMPORTANT: Make sure tray is in drawer when using liquid

detergent and removed when using powder detergent and do

not go over the Max line.

NOTE: Follow the manufacturer’s instructions to determine

the amount of detergent to use. Do not add single-dose

laundry packets, color-safe bleach, or fabric softener crystals

to dispensers. They will not dispense correctly.

Oxi dispenser

This dispenser holds up to ¾ cup (180 mL) Oxi booster or

other laundry booster, such as powdered or liquid color-safe

bleach. Laundry boosters are automatically dispensed at the

proper time during the wash cycle. Be sure to select Oxi from

the options to ensure proper dispensing.

NOTE: Fill dispenser with only oxi. Do not mix with bleach.

Liquid chlorine bleach dispenser

This dispenser holds up to ¾ cup (180 mL) liquid chlorine

bleach. The bleach will be automatically diluted and dispensed

at the optimum time during the wash cycle. This dispenser

cannot dilute powdered bleach.

NOTE: Fill dispenser with only liquid bleach.

Use only High Efﬁciency (HE) detergent.

CYCLE GUIDE

Settings shown are default settings for that cycle. Once you select a cycle, the default modiﬁers or the previous set modiﬁers for that cycle

will be lit. For best fabric care, choose the cycle that best ﬁts the load being washed. Not all cycles and options are available on all models.

Overly soiled

garments,

items that

need additional

cleaning effort

Power Wash

Use this cycle for heavily soiled or

sturdy items. Water-level sensing

process may take longer for some

items than for others because they

will absorb more water than other

fabric types.

Bright and darkly

colored cottons

and mixed loads.

Colors Use this cycle to wash darks and

colors, including mixed loads and

activewear.

Large items

such as sheets,

sleeping bags,

small comforters,

jackets, small

washable rugs

Bedding Use this cycle to wash large

items such as jackets and small

comforters. The washer will ﬁll with

enough water to wet down the load

before the wash portion of the cycle

begins and uses a higher water

level than other cycles.

Items to

wash:

Cycle: Temperature*: Soil Level: Spin

Speed:

Cycle Details:

*All rinses are cold.

CYCLE GUIDE

Settings shown are default settings for that cycle. Once you select a cycle, the default modiﬁers or the previous set modiﬁers for that cycle

will be lit. For best fabric care, choose the cycle that best ﬁts the load being washed. Not all cycles and options are available on all models.

Heavily soiled,

colorfast fabrics

Sanitize with

Oxi & Steam or

Sanitize with

Oxi (depending

on model)

Use this cycle to eliminate 99.9% of

bacteria when used in conjunction

with the Oxi option. Preset cycle

settings must be used to achieve the

proper sanitization. Be sure to add

an Oxi product to the Oxi dispenser.

Swimsuits and

items requiring

rinsing without

detergent

Drain & Spin/

Rinse & Spin

N/A N/A Combines high speed spin with the

option of a rinse only cycle for loads

requiring an additional spin-out to

reduce drying times or an additional

rinse cycle to refresh a load or

complete a cycle after power

interruption.

If you wish to run only the Drain &

Spin cycle, select the Drain & Spin

cycle.

If you wish to run a Rinse & Spin,

select both the Drain & Spin cycle

and the Extra Rinse Option.

Cottons, linens,

and mixed

garment loads

Normal Use this cycle for normally soiled

cottons and mixed fabric loads.

Cold- only

garments, bright

or darkly colored

cottons, linens,

casual and

mixed loads

Cold Wash Cold water with an additional

wash action gently lifts stains while

caring for fabrics. Settings may be

adjusted as desired, but must use

only cold water settings.

No-iron fabrics,

cottons, perm

press, linens,

synthetics

Wrinkle Control Use this cycle to wash loads of

no-iron fabrics such as sport shirts,

blouses, casual business clothes,

permanent press, and blends.

Machine-wash

silks, handwash

fabrics

Delicates Use this cycle to wash lightly

soiled items indicating “Machine

Washable Silks” or “Gentle” cycle

on the care label. Place small items

in mesh garment bags before

washing. This cycle uses a higher,

preset water level.

Lightly soiled,

small-sized

mixed-garment

loads.

Rapid Wash Use this cycle to quickly wash

lightly soiled garments and small

loads. The Rapid Wash cycle uses

shorter periods of more intense

washing to clean items quickly.

No clothes in

washer

Clean Washer

with affresh

N/A N/A N/A Use this cycle every 30 washes to

keep the inside of your washer fresh

and clean. This cycle uses a higher

water level. Use with affresh

Washer

Cleaner tablet or liquid chlorine bleach

to thoroughly clean the inside of your

washer. This cycle should not be

interrupted. See “Washer Care.”

IMPORTANT: Do not place garments

or other items in the washer during the

Clean Washer with affresh

cycle. Use

this cycle with an empty wash tub.

Items to

wash:

Cycle: Temperature*: Soil Level: Spin

Speed:

Cycle Details:

*All rinses are cold.

USING YOUR WASHER

• Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing

unexpected sounds.

• Sort items by recommended cycle, water temperature,

and colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing, because heat

can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items during

washing.

Helpful Tips:

• For best performance, use HE liquid detergent when washing

bulky items.

• When washing water-proof or water-resistant items, load

evenly. See “Cycle Guide” for tips and more information on

using the Bedding cycle.

• Use mesh garment bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up

lint from towels, rugs, and chenille fabrics.

Always read and follow fabric care label instructions to avoid

damage to your garments.

1. Sort and prepare your laundry 2. Add laundry products

For best performance, load items in

loose heaps evenly around the agitator.

Try mixing different sized items to

reduce tangling.

IMPORTANT: Items need to move

freely for best cleaning and to reduce wrinkling and tangling.

Single-dose laundry packest, color-safe bleach, or fabric softener

crystals can be added to the basket prior to adding laundry.

NOTE: Do not add clothes to washer basket prior to adding

laundry products. Always follow manufacturer’s instructions.

3. Load laundry into washer

6. Add liquid fabric softener or

Oxi to dispenser

Pour a measured amount of liquid fabric

softener or Oxi-type boosters, into tray; always

follow manufacturer’s directions for correct

amount of fabric softener or Oxi based on your load size. Close

dispenser drawer, and then select Oxi option. Oxi is added

during main wash and Fabric Softener is added during rinse.

IMPORTANT: Oxi option must be selected to ensure proper

distribution at correct time in cycle. Do not overﬁll or dilute.

Overﬁlling dispenser will cause fabric softener to immediately

dispense into washer.

If Extra Rinse option is selected, fabric softener will be

dispensed into the last rinse.

It is normal for a small amount of water to remain in the

dispenser at the end of a cycle.

Single Dose

Detergent

5. Add liquid chlorine bleach

to dispenser

Do not overﬁll, dilute, or use more than 1 cup (236 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Fabric softener tray

Add a measured amount of HE liquid detergent

into detergent tray. This tray holds 3 oz. (89 mL).

If adding powder HE detergent remove inside tray.

Do not overﬁll tray – adding too much detergent may cause

detergent to be dispensed into the washer too early.

NOTE: Make sure tray is in drawer when using liquid detergent

and removed when using powder detergent. Do not go over the

Max line.

IMPORTANT: Use only High Efﬁciency detergents. The package

will be marked “HE” or “High Efﬁciency.” Low-water washing

creates excessive sudsing with a regular non-HE detergent.

Using regular detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer’s instructions to determine the amount

of detergent to use.

HELPFUL TIP: See “Washer Maintenance” for information

recommended method of cleaning washer dispenser trays.

4. Add HE detergent

HE removable

detergent tray

NOTE: Do not add single-dose laundry packets, color-safe bleach,

or fabric softener crystals to dispensers. They will not dispense

correctly. Add to the basket prior to adding laundry.

Using Laundry Product Dispensers

Oxi tray

7. Touch POWER to turn on washer

Make sure the dispenser drawer is closed completely, then

touch POWER to turn on the washer. Other methods of

turning the washer on include opening the lid or turning the

cycle selection knob.

Liquid Chlorine

Bleach

Turn cycle knob to choose your wash cycle.

8. Select cycle

9. Select Temperature

Once you select a cycle, select the wash temperature by

touching the Temperature button to the desired setting. Even

for cold wash settings, some warm water may be added to the

washer to maintain a minimum temperature.

NOTE: Always read and follow fabric care label instructions to

avoid damage to your items. If not sure on which temperature to

use, refer to the chart below or select a cooler temperature.

12. Select cycle options, if desired

If you would like to add an Extra Rinse and/or Oxi option, touch

the button for that feature.

14. Touch and hold START/PAUSE

button to begin wash cycle

Touch and hold START/PAUSE button for up to 3 seconds to

start the wash cycle. When the cycle has ﬁnished, the end of

cycle signal will sound (if set). Promptly remove items when

cycle is done to avoid odor, reduce wrinkling, and rusting of

metal hooks, zippers, and snaps.

Unlocking the lid to add items

If you need to open the lid to add 1 or 2 missed items:

Touch START/PAUSE button to pause washer; the lid will unlock

once the washer movement has stopped. This may take several

minutes if the load was spinning at a high speed. Then close

lid and touch and hold START/PAUSE button again for up to

3 seconds to restart the cycle.

IMPORTANT: If lid is left open for more than 10 minutes the

water will pump out and F8E6 error code will appear on the

display.

10. Select SOIL LEVEL

Once you select a cycle, select the soil level by touching the

Soil Level button to the desired setting.

Light soils

Colors that

bleed or

fade

Heavy

soils

Whites

Pastels

Moderate

soils

Bright

colors

11. Select SPIN SPEED

Once you select a cycle, you may adjust the spin speed

by touching the Spin Speed button until you reach the

desired setting.

13. Select DEEP FILL mode, if desired

Once you select a cycle, you may disable Auto Sensing mode

and turn on the Deep Fill mode by pressing the DEEP FILL

button.

WASHER MAINTENANCE

Replace inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

“Installation Instructions” for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer

Clean and Performing at its Best

1. Always use High Efﬁciency (HE) detergents and follow the

HE detergent manufacturer’s instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the rate

at which detergent and soil residue accumulate inside your

washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly cleaning

procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water volumes

in combination with affresh

Washer Cleaner or liquid chlorine

bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

e. Close the washer lid.

f. Select the CLEAN WASHER cycle.

g. Touch and hold the START/Pause button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, touch POWER. After the Clean Washer cycle

has stopped, run a RINSE & SPIN cycle to rinse cleaner from

washer.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the

bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

e. Select the CLEAN WASHER cycle.

f. Touch and hold the START/Pause button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, touch POWER. After the Clean Washer cycle

has stopped, run a RINSE & SPIN cycle to rinse cleaner

from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ﬁll to a water level higher than in normal wash

cycles to provide rinsing at a level above the water line for

normal wash cycle.

2. During this cycle, there will be some agitation and spinning

to increase the removal of soils.

After this cycle is complete, leave the lid open to allow

for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may ﬁnd some residue

buildup in the washer’s dispensers. To remove residue from

the dispensers, wipe them with a damp cloth and towel dry.

Do not attempt to remove the dispensers or trim for cleaning.

The dispensers and trim are not removable. If your model has

a dispenser drawer, however, remove the drawer and clean it

before or after you run the Clean Washer cycle. Use an all-

purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use

only mild soaps or cleaners when cleaning external washer

surfaces.

IMPORTANT: To avoid damaging the washer’s ﬁnish, do not

use abrasive products.

Operate your washer only when you are home.

If moving, or not using your washer for a period of time, follow

these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ﬂooding due

to water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

2. Plug in washer or reconnect power.

3. Run washer through BEDDING cycle to clean washer and

remove antifreeze, if used. Use only HE High Efﬁciency

detergent. Use ½ the manufacturer’s recommended

amount for a medium-size load.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped

until washer is placed in new location. Transport washer in

upright position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to “Installation Instructions” to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

CLEANING YOUR DISPENSER

IMPORTANT: Dispenser drawer and tray are not dishwasher

safe.

You may ﬁnd laundry product residue leftover in your dispenser

drawer. To remove residue, follow this recommended cleaning

procedure:

1. Pull drawer out until you feel resistance.

2. Push 2 tabs downward, and then continue pulling out.

3. Wash in warm, soapy water, using a mild detergent.

4. Rinse with warm water.

5. Air dry, or dry with a towel, then place back into slot.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Vibration, rocking, or

“walking”

Feet may not be in contact with the

ﬂoor and locked.

Front and rear feet must be in ﬁrm contact with ﬂoor, and washer

must be level to operate properly. See “Installation Instructions”.

Washer may not be level. Check ﬂoor for ﬂexing or sagging. If ﬂooring is uneven, a ¾"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Vibration during spinning

or washer stopped

Load could be unbalanced. Load items in loose heaps evenly around the agitator. Adding

wet items to washer or adding more water to basket could

unbalance washer.

Avoid washing single items. Balance a single item such as a rug or

jeans jacket with a few extra items. Redistribute the load, close the

lid, and touch and hold START/PAUSE.

Use Bedding cycle for oversized, non-absorbent items such as

jackets and small comforters.

Item or load not suitable for selected cycle. See “Cycle Guide” and

“Using Your Washer” in this Use and Care Guide.

Noises - For normal operating sounds, go to www.maytag.com/product_help

Clicking or metallic noises Objects may be caught in washer drain

system.

Empty pockets before washing. Loose items such as coins could fall

between basket and tub or may block pump. It may be necessary to

call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging as ﬁnal amounts of water are

removed during the spin/drain cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have started

the washer. This is normal.

Whirring Basket may be slowing down. You may hear the whirring sound of the basket decelerating.

This is normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level. Check that load

is not unbalanced or tightly packed.

Fill hoses not attached tightly. Tighten ﬁll-hose connection.

Fill hose washers. Make sure all four ﬁll hose ﬂat washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks

or clogged sink or drain.

Water can backup out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water pipes,

and faucets.)

Washer not loaded as recommended. Unbalanced loading can cause basket to be out of alignment and

cause water to splash off tub. See “Using Your Washer” for loading

instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for Auto Sensing Water Level mode.

The load will not be completely under water. The washer senses

load sizes and adds the correct amount of water for optimal cleaning

performance in High Efﬁciency operation. See “What’s New under

the Lid.”.

Run clean washer cycle to optimize the water level and wash

performance.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run or ﬁll,

washer stops working

or wash light remains

on (indicating that the

washer was unable to

ﬁll appropriately) (cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be stopped to reduce suds.

Washer may be tightly packed. Remove several items, rearrange load evenly around the agitator.

Close lid, touch and hold START/PAUSE button.

Add only 1 or 2 additional garments after washer is started.

Do not add more water to the washer.

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents can slow or

stop the washer. Always measure detergent and follow detergent

directions based on your load requirements.

To remove suds, cancel cycle. Select DRAIN & SPIN cycle and the

Extra Rinse option. Touch and hold START/PAUSE button. Do not

add more detergent.

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run or ﬁll,

washer stops working

or wash light remains

on (indicating that the

washer was unable to

ﬁll appropriately)

Check for proper water supply. Both hoses must be attached and have water ﬂowing to inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ﬂow.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer not draining/

spinning, loads are still

wet, or spin light remains

on (indicating that the

washer was unable to

pump out water within

10 minutes)

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Using a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles with

high spin speeds. Use the recommended cycle/spin speed for your

item. To remove extra water in the load, select DRAIN & SPIN. Load

may need to be rearranged to allow even distribution of the load in

the basket.

The washer may be tightly packed or

unbalanced.

Tightly packed or unbalanced loads may not allow the washer to

spin correctly, leaving the load wetter than normal. Evenly arrange

the wet load for balanced spinning. Select the Drain & Spin cycle

to remove excess water. See “Using Your Washer” for loading

recommendations.

Load off balanced. See “Vibration or Off-Balance” in Troubleshooting section for more

information.

Check plumbing for correct drain hose

installation. Drain hose extends into

standpipe farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form and

securely attach to drainpipe or tub. Do not tape over drain opening.

Lower drain hose if the end is higher than 96" (2.4 m) above the

ﬂoor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Use only HE detergent. Always measure and follow detergent

directions for your load. To remove extra suds, select RINSE &

SPIN. Do not add detergent.

Dry spots on load after

cycle

High speed spins extract more

moisture than traditional top-load

washers.

The high spin speeds combined with air ﬂow during the ﬁnal spin

can cause items near the top of the load to develop dry spots

during the ﬁnal spin. This is normal.

Incorrect or wrong wash

or rinse temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and have

both hot and cold water ﬂowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy-saving controlled wash

temperatures.

High Efﬁciency washers use cooler wash and rinse water

temperatures than traditional top-load washer. This includes cooler

hot and warm washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water ﬂowing to the inlet

valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from operating

correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions based

on load size and soil level.

Washer may be tightly packed. The washer is less efﬁcient at rinsing when tightly packed.

Load garments in loose heaps evenly around the agitator.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer is started.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Sand, pet hair, lint, etc. on

load after washing

Heavy sand, pet hair, lint, and

detergent or bleach residues

may require additional rinsing.

Add an Extra Rinse to the selected cycle.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed, however

items will be wetter than those using a higher speed spin. See the

“Cycle Guide” to match your load with the best cycle.

Load items in loose heaps evenly around the agitator.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of items being washed.

Not cleaning or removing

stains

Added more water to washer. Washer senses load size and adds correct amount of water. This is

normal and necessary for clothes to move. It is normal for the wash

load to be not completely covered in water. Added water lifts the

laundry off the agitator, resulting in less effective cleaning.

Washer not loaded as recommended. Washer is less efﬁcient at cleaning when tightly packed.

Load garments in loose heaps evenly around the agitator.

Add only 1 or 2 additional garments after washer is started.

Adding detergent on top of load. Add detergent, Oxi products and color-safe bleach to the bottom of

the basket before adding the load items.

Not washing like colors together. Wash like colors together and remove promptly after the cycle is

complete to avoid dye transfer.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from operating

correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric type. Use a higher soil level cycle option and warmer wash temperature to

improve cleaning.

Use Power Wash

cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle.

Not using dispenser. Use dispenser to avoid chlorine bleach and fabric softener staining.

Load dispenser before starting a cycle.

Do not add products directly onto load.

Incorrect dispenser

operation

Clogged dispensers or laundry

products dispensing too soon.

Do not overﬁll dispenser. Overﬁlling causes immediate dispensing.

Load dispensers before starting a cycle.

It is normal for small amounts of water to be remain in dispenser at

the end of the cycle.

Homes with low water pressure may result in residual powder in the

dispenser. To avoid, select a warmer wash temperature if possible,

depending on your load.

Clean dispenser nozzle and make sure drawer is properly seated.

Liquid chlorine bleach not used in

dispenser.

Use only liquid chlorine bleach in the bleach dispenser.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Fabric Damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Items may have been damaged before

washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if washer is

tightly packed.

Load items in loose heaps evenly around the agitator.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional items after washer is started.

Liquid chlorine bleach may have been

added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when loading

and unloading washer.

Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with

the best cycle.

Odors Monthly maintenance not done as

recommended.

Run the Clean Washer with affresh

cycle after every 30 washes.

See “Washer Care” in Washer Maintenance.

Unload washer as soon as cycle is complete.

Using wrong or too much detergent. Use only HE detergent. Be sure to measure correctly. Always

follow the manufacturer’s directions.

See “Washer Care” section.

Lid locked light is

ﬂashing

The lid is not closed. Close the lid. The washer will not start or ﬁll with the lid open.

A cycle was stopped or paused

using the Start/Pause button.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Powdered detergent not

dissolving completely in

load

Using too much HE detergent. Follow the manufacturer’s instructions to determine the amount

of detergent to use.

Water temperature is very cold. Select a warmer wash temperature.

Try adding the detergent to the basket prior to adding laundry,

rather than using the detergent dispenser.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Follow the manufacturer’s instructions to avoid damage to

your items.

First try the solutions suggested here or visit our website at www.maytag.com/product_help -

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

MAYTAG

LAUNDRY

LIMITED WARRANTY

1. Commercial, non-residential, multiple-family use, or use inconsistent with

published user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation,

installation not in accordance with electrical or plumbing codes, or

correction of household electrical or plumbing (i.e. house wiring, fuses,

or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters,

preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Maytag parts

or accessories.

6. Conversion of your product from natural gas or L.P. gas or reversal of

appliance doors.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use

with products not approved by Maytag.

8. Repairs to parts or systems to correct product damage or defects caused

by unauthorized service, alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage

to appliance ﬁnishes unless such damage results from defects in

materials and workmanship and is reported to Maytag within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic

or corrosive environments, including but not limited to, high salt

concentrations, high moisture or humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Maytag servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e.

trim, decorative panels, ﬂooring, cabinetry, islands, countertops, drywall,

etc.) that interfere with servicing, removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers

removed, altered, or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by the customer.

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair.

Some questions can be addressed without service. Please take a few minutes to review the

Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on

the right to access additional resources, or visit https://www.maytag.com/product_help.

2. All warranty service is provided exclusively by our authorized Maytag Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Maytag Customer eXperience Center

In the U.S.A. call 1-800-688-9900. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.

FIVE YEAR LIMITED WARRANTY

(PARTS AND LABOR)

For five years from the date of purchase, when this major

appliance is installed, operated, and maintained according to

instructions attached to or furnished with the product, Maytag

brand of Whirlpool Corporation or Whirlpool Canada LP

(hereafter “Maytag”) will pay for factory specified parts and

repair labor to correct defects in materials or workmanship

that existed when this major appliance was purchased, or

at its sole discretion replace the product. In the event of

product replacement, your appliance will be warranted by the

remaining term of the original unit’s warranty period.

SIXTH THROUGH TENTH YEAR LIMITED WARRANTY

(DRIVE MOTOR AND WASH BASKET ONLY - LABOR

NOT INCLUDED)

In the sixth through tenth years from the date of original

purchase, when this major appliance is installed, operated, and

maintained according to instructions attached to or furnished

with the product, Maytag will pay for factory specified parts for

the following components to correct non-cosmetic defects in

materials or workmanship in these parts that prevent function

of this major appliance and that existed when this major

appliance was purchased. This is a limited 10 year warranty on

the below named parts only and does not include repair labor.

n Drive Motor n Wash Basket (Side Walls Only)

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a Maytag

designated service company. This limited warranty is valid

only in the United States or Canada and applies only when

the major appliance is used in the country in which it was

purchased. This limited warranty is effective from the date of

original consumer purchase. Proof of original purchase date is

required to obtain service under this limited warranty.

https://www.maytag.com/product_help

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO TEN YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you.

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.

07/16

TEN YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

SÉCURITÉ DE LA LAVEUSE

La page charge ...

Maytag MVWB766FW MVWB766FW Use and Care EN

Marque: Maytag

Modèle: MVWB766FW

Catégorie: Machines à laver

Taper: MVWB766FW Use and Care EN

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MVWB766FW

Maytag MVWB766FW MVWB766FW Use and Care EN

Maytag MVWB766FW MVWB766FW Use and Care EN

dans d''autres langues

Documents connexes

Autres documents