Lincoln Electric Ranger 305D Mode d'emploi

Marque: Lincoln Electric

Modèle: Ranger 305D

Catégorie: Système de soudage

Taper: Mode d'emploi

Ranger 305 D (CE)

OPERATOR’S MANUAL

IM813

August, 2005

Safety Depends on You

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However, your

overall safety can be increased by

proper installation ... and thought-

ful operation on your part. DO

NOT INSTALL, OPERATE OR

REPAIR THIS EQUIPMENT

WITHOUT READING THIS

MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED

THROUGHOUT. And, most

importantly, think before you act

and be careful.

For use with machines having Code Numbers:

11027, 11039

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

EN 60974-1

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vaporiz-

ing on contact with hot engine parts and

igniting. Do not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing and

tools away from V-belts, gears, fans and all other moving

parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box

351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available

from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ‘95

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents

are known to the State of California to cause can-

cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

The Above For Diesel Engines

The Above For Gasoline Engines

SAFETY

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety precautions, if welding

must be performed under electrically hazardous

conditions (in damp locations or while wearing wet

clothing; on metal structures such as floors, gratings or

scaffolds; when in cramped positions such as sitting,

kneeling or lying, if there is a high risk of unavoidable or

accidental contact with the workpiece or ground) use

the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASES

can be dangerous.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases.When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special

ventilation such as stainless or hard facing (see

instructions on container or MSDS) or on lead or

cadmium plated steel and other metals or coatings

which produce highly toxic fumes, keep exposure as

low as possible and below Threshold Limit Values (TLV)

using local exhaust or mechanical ventilation. In

confined spaces or in some circumstances, outdoors, a

respirator may be required. Additional precautions are

also required when welding on galvanized steel.

5.b.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors to

form phosgene, a highly toxic gas, and other irritating pro-

ducts.

5.c. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employer’s safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.e. Also see item 1.b.

Mar ‘95

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National

Electrical Code, all local codes and the manufacturer’s

recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

iii

SAFETY

iii

Mar ‘95

WELDING SPARKS can

cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

SAFETY

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuel aussi bien que les précautions de sûreté générales suiv-

antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une grande

partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder

parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se protéger

contre les chutes dans le cas ou on recoit un choc. Ne jamais

enrouler le câble-électrode autour de n’importe quelle partie

du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray-

onnement de l’arc et des projections quand on soude ou

quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de

soudage. Se protéger avec des vêtements de protection libres

de l’huile, tels que les gants en cuir, chemise épaisse, pan-

talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible

de la zone de travail qu’il est pratique de le faire. Si on place

la masse sur la charpente de la construction ou d’autres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques d’incendie ou d’echauffement des chaines et des

câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs

du solvant pour produire du phosgéne (gas fortement toxique)

ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de

l’électricité et aux recommendations du fabricant. Le dispositif

de montage ou la piece à souder doit être branché à une

bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront

effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-

er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Mar. ‘93

SAFETY

RANGER 305D (CE)

vii

SAFETY

vii

RANGER 305D (CE)

viii

SAFETY

viii

RANGER 305D (CE)

ixix

Thank You

for selecting a QUALITY product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or

loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to

this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

TABLE OF CONTENTS

Page

Installation.......................................................................................................................Section A

Technical Specifications.......................................................................................................A-1

Safety Precautions ........................................................................................................A-2

Location and Ventilation................................................................................................A-2

Stacking ........................................................................................................................A-2

Angle of Operation ........................................................................................................A-2

Lifting.............................................................................................................................A-2

Additional Safety Precautions .......................................................................................A-2

High Altitude Operation .................................................................................................A-2

High Temperature Operation ........................................................................................A-2

Cold Weather Operation ...............................................................................................A-2

Towing...........................................................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-3

Oil..................................................................................................................................A-3

Fuel ...............................................................................................................................A-3

Engine Coolant..............................................................................................................A-3

Battery Connections......................................................................................................A-3

Muffler Outlet Pipe ........................................................................................................A-3

Spark Arrester ...............................................................................................................A-4

Remote Control .............................................................................................................A-4

Electrical Connections..........................................................................................................A-4

Machine Grounding.......................................................................................................A-4

Welding Terminals ........................................................................................................A-4

Welding Output Cables .................................................................................................A-4

Cable Installation...........................................................................................................A-5

Auxiliary Power Receptacles and Plugs...............................................................................A-5

Standby Power Connections ................................................................................................A-5

Connection of Lincoln Electric Wire Feeders................................................................A-5,A-6

________________________________________________________________________________

Operation.........................................................................................................................Section B

Safety Precautions ..............................................................................................................B-1

General Description..............................................................................................................B-1

For Auxiliary Power ..............................................................................................................B-1

Engine Operation..................................................................................................................B-1

Break in Period.....................................................................................................................B-1

Add Fuel ...............................................................................................................................B-1

Fuel ......................................................................................................................................B-1

Welder Controls ............................................................................................................B-2

Engine Controls.............................................................................................................B-3

Starting and Stopping the Engine ...........................................................................B-3, B4

Stopping .......................................................................................................................B-4

Welding Operation................................................................................................................B-5

Duty Cycle.....................................................................................................................B-5

Constant Current (Stick) Welding..................................................................................B-5

Downhill Pipe (Stick) Welding .......................................................................................B-5

Tig Welding ...................................................................................................................B-5

Typical Current Ranges for Tungsten Electrodes .........................................................B-5

Wire Welding-CV...........................................................................................................B-6

Arc Gouging ..................................................................................................................B-6

Auxiliary Power .............................................................................................................B-7

Extension Cord Recommendations...............................................................................B-7

________________________________________________________________________________

Accessories.....................................................................................................Section C

Field Installed Options / Accessories ...............................................................................C-1

________________________________________________________________________________

TABLE OF CONTENTS

Maintenance......................................................................................................Section D

Safety Precautions ................................................................................................D-1

Routine Maintenance ............................................................................................D-1

Engine Maintenance Components ........................................................................D-1

Kubota Diesel Engine............................................................................................D-1

Engine Oil Change..........................................................................................D-2

Engine Oil Refill Capacities.............................................................................D-2

Engine Oil Filter Change.................................................................................D-2

Air Cleaner Service .........................................................................................D-2

Service Instructions And Installation Tips for Engine Air Filter .......................D-3

Cooling System .....................................................................................................D-4

Fan Belt...........................................................................................................D-4

Fuel .................................................................................................................D-4

Bleeding the Fuel System ...............................................................................D-4

Fuel Filter ........................................................................................................D-5

Engine Adjustment ..........................................................................................D-5

Battery Maintenance .......................................................................................D-5

Servicing Optional Spark Arrestor ...................................................................D-5

Welder / Generator Maintenance ........................................................................D-6

Storage ...........................................................................................................D-6

Cleaning..........................................................................................................D-6

Brush Removal and Replacement ..................................................................D-6

________________________________________________________________________

Troubleshooting..............................................................................................Section E

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide.............................................................................E-2 thru E-6

________________________________________________________________________

Diagrams and Dimension Print ......................................................................Section F

________________________________________________________________________

Parts List..................................................................................................................P479

________________________________________________________________________

RANGER 305D (CE)

(1) Output rating in watts is equivalent to volt-amperes at unity power factor. Output voltage is within ± 10% at all loads up to rated capacity. When welding,

available auxiliary power will be reduced.

(2) To top of enclosure, add 152mm (6 “) to top of exhaust elbow.

(3) Engine warranty may vary outside of the USA. (See Engine warranty for details)

(4) Center-Tapped to ground.

A-1

INSTALLATION

A-1

TECHNICAL SPECIFICATIONS - RANGER 305D (CE) K2279-1 & K2279-2

Make/Model Description Speed (RPM) Displacement Starting Capacities

cu. in. (cu. cm.) System

3 cylinder 43.88(789)

12VDC Battery &

Fuel:

4 stroke starter 45L (12 US.gal.)

15.9 HP High Idle 3100

Bore x Stroke inch (mm)

Oil:

Kubota

(3)

(12 KW)

3.2L(3.4 US. Qts.)

D722 Net intermittent Full Load 3000

2.64 x 2.68

(Group 58; 550 Radiator Coolant:

3000 RPM (67 x 68 mm) cold crank amps) 3.6L(3.85 U Qts)

naturally aspirated Low Idle 2200 Battery Charger

water cooled engine (3.6L)

INPUT - DIESEL ENGINE

RATED OUTPUT @ 40° C (104° F) - WELDER

HEIGHT WIDTH DEPTH WEIGHT

909mm 546mm 1524mm

30.0 in.

(2)

21.50 in 60.0 in.

LUBRICATION EMISSIONS FUEL SYSTEM GOVERNOR

Full Pressure Electric Fuel Pump, Auto air bleed system

with Full Flow Filter Certified to EPA Tier I Electric shutoff solenoid Mechanical Governor

Indirect fuel injector

AIR CLEANER ENGINE IDLER MUFFLER ENGINE PROTECTION

Low noise Muffler: Shutdown on low oil

Single Element Automatic Idler Top outlet can be rotated. pressure & engine

Made from long life, aluminized steel. temperature

ENGINE WARRANTY: 2 year complete (parts and labor) 3rd. year major components (parts and labor)

(3)

Welding Process

DC Constant Current

DC Pipe Current

Touch-Start™TIG

DC Constant Voltage

Output Range

20 TO 305 AMPS

40 TO 300 AMPS

20 TO 250 AMPS

14 TO 29 VOLTS

Max. Weld OCV

@Rated Load RPM

60 Volts

Welding Output

Current/Voltage/Duty Cycle

250A / 30V / 100%

250A / 20V / 100%

250A / 27V / 100%

Auxiliary Power

(1)

8,500 Watts Peak, / 8,000 Watts Continuous, 50 Hz 115 & 230 Volts - 1 Phase

8,500 Watts Peak, / 8,000 Watts Continuous, 50 Hz 400 Volts - 3 Phase

Sound Levels

Sound Power: 98 dB Lwa

PHYSICAL DIMENSIONS

ENGINE

MODEL NUMBER

Receptacles

Residual Current Device (RCD)

Circuit Breakers (Thermal/Magnetic)

K2279-1 (UK)

400V (3 Ph) x 1

230V (1 Ph) x 1

115V x 1

(4)

14 Pin Connector

6 Pin Connector

4-pole, 25 Amp

(30mA trip current)

3 Phase, 20 Amp x 1

1 Phase, 15 Amp x 5

K2279-2 (EUROPE)

400V (3 Ph) x 1

230V (1 Ph) x 2

14 Pin Connector

6 Pin Connector

4-pole, 25 Amp

(30mA trip current)

3 Phase, 20 Amp x 1

1 Phase, 15 Amp x 4

RATED OUTPUT @ 40° C (104° F) - GENERATOR

341kg. (752lbs.)

STACKING

RANGER 305D (CE) machines cannot be stacked.

ANGLE OF OPERATION

Engines are designed to run in the level condition which is

where the optimum performance is achieved. The maxi-

mum angle of continuous operation is 20 degrees in all

directions, 35 degrees Intermittent (less than 10 minutes

continuous) in all directions. If the engine is to be operated

at an angle, provisions must be made for checking and

maintaining the oil level at the normal (FULL) oil capacity in

the crankcase.

When operating the welder at an angle, the effective fuel

capacity will be slightly less than the specified 45 liters (12

gallons).

LIFTING

The machine weighs approximately 374 kg. (824 lbs) with a

full tank of fuel. A lift bail is mounted to the machine and

should always be used when lifting the machine.

HIGH ALTITUDE OPERATION

At higher altitudes, output derating may be necessary. For

maximum rating, derate the machine 2.5% to 3.5% for every

305m (1000ft.). Due to new EPA and other local emissions

regulations, modifications to the engine for high altitude are

restricted within the United States and some European

Countries. Use above 1828m (6000 ft.) may be limited due

to poor engine performance or excessive exhaust smoke.

An authorized Kubota engine field service shop should be

contacted to determine if any adjustments can be made for

operation in higher elevations locally.

HIGH TEMPERATURE OPERATION

At temperatures above 40°C, output derating is necessary.

For maximum output ratings, derate the welder output 2

volts for every 10°C above 40°C.

Cold weather starting:

With a fully charged battery and the proper oil, the engine

should start satisfactorily down to about 15°C (5°F). If the

engine must be frequently started at or below -5°C (23°F), it

may be desirable to install cold-starting aides. The use of

No. 1D diesel fuel is recommended in place of No. 2D at

temperatures below

-5°C (23°F). Allow the engine to warm up before applying a

load or switching to high idle.

Note: Extreme cold weather starting may require longer

glow plug operation.

Under no conditions should ether or other starting flu-

ids be used!

-------------------------------------------------------------------------------

WARNING

A-2

INSTALLATION

A-2

SAFETY PRECAUTIONS

Only qualified personnel should install,

use, or service this equipment.

LOCATION AND VENTILATION

The welder should be located to provide an unrestricted flow

of clean, cool air to the cooling air inlets and to avoid restrict-

ing the cooling air outlets. Also, locate the welder so that the

engine exhaust fumes are properly vented to an outside

area.

ADDITIONAL SAFETY PRECAUTIONS

• Lift only with equipment of ade-

quate lifting capacity.

• Be sure machine is stable when lift-

ing.

• Do not lift this machine using lift

bail if it is equipped with a heavy

accessory such as trailer or gas

cylinder.

FALLING • Do not lift machine if lift bail is

EQUIPMENT can damaged.

cause injury. • Do not operate machine while

suspended from lift bail.

--------------------------------------------------------------------------------

Do not attempt to use this equipment until you

have thoroughly read the engine manufacturer’s

manual supplied with your welder. It includes

important safety precautions, detailed engine

starting, operating and maintenance instructions,

and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or

electrode with skin or wet clothing.

• Insulate yourself from work and

ground

• Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

• Use in open, well ventilated areas or

vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.

• Do not operate with doors open or

guards off.

• Stop engine before servicing.

• Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information at

front of this operator’s manual.

WARNING

RANGER 305D (CE)

A-3

INSTALLATION

RANGER 305D (CE)

A-3

TOWING

Check with distributor for the recommended trailer for use with

this equipment for road, in-plant and yard towing by a vehicle. If

the user adapts a non-Lincoln trailer, he must assume responsi-

bility that the method of attachment and usage does not result

in a safety hazard nor damage the welding equipment. Some of

the factors to be considered are as follows:

1. Design capacity of trailer vs. weight of Lincoln equipment and

likely additional attachments.

2. Proper support of, and attachment to, the base of the weld-

ing equipment so there will be no undue stress to the frame-

work.

3. Proper placement of the equipment on the trailer to insure

stability side to side and front to back when being moved

and when standing by itself while being operated or ser-

viced.

4. Typical conditions of use, i.e., travel speed; roughness of sur-

face on which the trailer will be operated; environmental con-

ditions; like maintenance.

5. Conformance with laws in nation / region to be used.

PRE-OPERATION ENGINE SERVICE

READ the engine operating and maintenance instruc-

tions supplied with this machine.

• Stop engine and allow to cool before fueling

• Do not smoke when fueling

• Fill fuel tank at a moderate rate and do not over-

fill.

• Wipe up spilled fuel and allow fumes to clear

before starting engine

• Keep sparks and flame away from tank.

------------------------------------------------------------------------

OIL

The machine is shipped with the engine crankcase

filled with high quality SAE 10W-30 Oil that meets

classification CG-4 or CH-4 for diesel engines. Check

the oil level before starting the engine. If it is not up to

the full mark on the dip stick, add oil as required.

Check the oil level every four hours of running time

during the first 50 running hours. Refer to the engine

Operator’s Manual for specific oil recommendations

and break-in information. The oil change interval is

dependent on the quality of the oil and the operating

environment. Refer to the Engine Operator’s Manual

for more details on the proper service and mainte-

nance intervals.

FUEL

• Fill the fuel tank with clean, fresh fuel. The

capacity of the tank is 45.4 liters. When the fuel

gauge reads empty the tank contains approxi-

mately 7 liters of reserve fuel.

NOTE: A fuel shut off valve is located on the pre-

filter/sediment filter. Which should be in

the closed position when the welder is not

operated for extended periods of time.

------------------------------------------------------------------------

ENGINE COOLING SYSTEM

Air to cool the engine is drawn in the base sides

and exhaust through radiator & case back. It is

important that the intake and exhaust air is not

restricted. Allow a minimum clearance of 0.6m (2

feet) from the case back and 40cm (16”) from

either side of the base to a vertical surface.

------------------------------------------------------------------------

WARNING

VEHICLE MOUNTING

Improperly mounted concentrated loads may

cause unstable vehicle handling and tires or other

components to fail.

• Only transport this Equipment on serviceable

vehicles which are rated and designed for such

loads.

• Distribute, balance and secure loads so vehicle

is stable under conditions of use.

• Do not exceed maximum rated loads for compo-

nents such as suspension, axles and tires.

• Use appropriate nuts bolts and lockwashers to

attach the equipment base to the metal bed or

frame of vehicle.

• Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------

WARNING

• Stop engine while fueling.

• Do not smoke when fueling.

• Keep sparks and flame away

from tank.

• Do not leave unattended while

fueling.

• Wipe up spilled fuel and allow

fumes to clear before starting

engine.

• Do not overfill tank, fuel

expansion may cause over-

flow.

DIESEL FUEL ONLY

------------------------------------------------------------------------

WARNING

DIESEL FUEL

can cause fire.

A-4

INSTALLATION

RANGER 305D (CE)

A-4

BATTERY CONNECTION

Use caution as the electrolyte is a strong acid that

can burn skin and damage eyes.

------------------------------------------------------------------------

The machine is shipped with the negative battery

cable disconnected. Make certain that the RUN-STOP

switch is in the STOP position. Attach the negative

battery cable to the negative battery terminal and tight-

en using a 13mm socket or wrench. It may be helpful

to remove the coolant over-fill bottle. Pull up on bottle

to remove from bracket.

NOTE: This machine is furnished with a wet charged

battery; if unused for several months, the battery may

require a booster charge. Be careful to charge the bat-

tery with the correct polarity.

MUFFLER OUTLET PIPE

Using the clamp provided secure the outlet pipe to the

outlet tube with the pipe positioned such that it will

direct the exhaust to the radiator end of the machine.

Tighten using an adjustable wrench.

SPARK ARRESTER

Some local laws may require that gasoline or diesel

engines be equipped with exhaust spark arresters

when they are operated in certain locations where

unarrested sparks may present a fire hazard. The

standard muffler included with this welder does not

qualify as a spark arrester. When required by local

regulations, a suitable spark arrester, such as the

K1898-1 must be installed and properly maintained.

An incorrect spark arrestor may lead to damage to

the engine or adversely affect performance.

------------------------------------------------------------------------

REMOTE CONTROL

The machine is equipped with a 6-pin and a 14-pin

connector. The 6-pin connector is for connecting the

K857 or K857-1 Remote Control or for TIG welding,

the K870 foot Amptrol or the K936-2 hand Amptrol.

When in the CC-STICK, DOWNHILL PIPE, or CV-

WIRE modes and when a remote control is connected

to the 6-pin Connector, the auto-sensing circuit auto-

matically switches the OUTPUT control from control at

the welder to remote control.

When in TOUCH START TIG mode and when a

Amptrol is connected to the 6-Pin Connector, the

OUTPUT dial is used to set the maximum current

range of the CURRENT CONTROL of the Amptrol.

The 14-pin connector is used to directly connect a

wire feeder control cable. In the CV-WIRE mode,

when the control cable is connected to the 14-pin con-

nector, the auto-sensing circuit automatically makes

the Output Control inactive and the wire feeder volt-

age control active

NOTE: When a wire feeder with a built in welding

voltage control is connected to the 14-pin connec-

tor, do not connect anything to the 6-pin connec-

tor.

------------------------------------------------------------------------

ELECTRICAL CONNECTIONS

MACHINE GROUNDING

Because this portable engine driven welder creates its

own power, it is not necessary to connect its frame to

an earth ground, unless the machine is connected to

premises wiring (home, shop, etc.)

To prevent dangerous electric shock, other equipment

to which this engine driven welder supplies power

must:

• Be grounded to the frame of the welder using a

grounded type plug.

• Be double insulated.

• Do not ground the machine to a pipe that carries

explosive or combustible material.

------------------------------------------------------------------------

When this welder is mounted on a truck or trailer, its

frame must be electrically bonded to the metal frame

of the vehicle. Use a #8 or larger copper wire connect-

ed between the machine grounding stud and the

frame of the vehicle. When this engine driven welder

is connected to premises wiring such as that in a

home or shop, its frame must be connected to the

system earth ground. See further connection instruc-

tions in the section entitled "Standby Power

Connections" .

In general, if the machine is to be grounded, it should

be connected with a #8 or larger copper wire to a solid

earth ground such as a metal water pipe going into

the ground for at least ten feet and having no insulat-

ed joints, or to the metal framework of a building

which has been effectively grounded.

A machine grounding stud marked with the symbol

is provided on the front of the welder.

CAUTION

WARNING

A-5

INSTALLATION

RANGER 305D (CE)

A-5

WELDING TERMINALS

The machine is equipped with a toggle switch for

selecting "hot" welding terminal when in the "WELD

TERMINALS ON" position or "cold" welding terminal

when in the "REMOTE" position.

WELDING OUTPUT CABLES

With the engine off connect the electrode and work

cables to the output studs. The welding process dic-

tates the polarity of the electrode cable. These con-

nections should be checked periodically and tightened

with a 19mm wrench.

Table A.1 lists recommended cable sizes and lengths

for rated current and duty cycle. Length refers to the

distance from the welder to the work and back to the

welder. Cable diameters are increased for long cable

lengths to reduce voltage drops.

TABLE A-1

CABLE INSTALLATION

Install the welding cables to your machine as follows:

1. The diesel engine must be OFF to install welding

cables.

2. Remove the flanged nuts from the output terminals.

3. Connect the electrode holder and work cables to

the weld output terminals. The terminals are identi-

fied on the case front.

4. Tighten the flanged nuts securely.

5. Be certain that the metal piece you are welding (the

“work”) is properly connected to the work clamp and

cable.

6. Check and tighten the connections periodically.

• Loose connections will cause the output termi-

nals to overheat. The terminals may eventually

melt.

• Do not cross the welding cables at the output

terminal connection. Keep the cables isolated

and separate from one another.

------------------------------------------------------------------------

AUXILIARY POWER

The auxiliary power capacity is 8500 watts Peak,

8,000 Watts Continuous of 50 Hz, three phase power.

The auxiliary power capacity rating in watts is equiva-

lent to volt-amperes at unity power factor. The max

permissible current of the 400 VAC output is 20 amps.

Output voltage is within ± 10% at all loads up to the

rated capacity.

STANDBY POWER CONNECTIONS

The machine is suitable for temporary, standby or

emergency power using the engine manufacturer’s

recommended maintenance schedule.

The machine can be permanently installed as a stand-

by power unit for 400 VAC, three phase, 20 amp ser-

vice.

Connections must be made by a licensed electrician

who can determine how the power can be adapted to

the particular installation and comply with all applica-

ble electrical codes.

• Take necessary steps to assure load is limited to the

capacity of the RANGER 305D (CE).

• Only a licensed, certified, trained electrician

should install the machine to a premises or resi-

dential electrical system. Be certain that:

• The installation complies with the National

Electrical Code and all other applicable electrical

codes.

• The premises is isolated and no feedback into

the utility system can occur. Certain laws require

the premises to be isolated before the generator

is linked to the premises. Check your local

requirements.

-----------------------------------------------------------------------

CONNECTION OF LINCOLN ELECTRIC

WIRE FEEDERS

Connection of LN-15 to the RANGER 305D (CE)

These connections instructions apply to both the LN-

15 Across-The-Arc and Control Cable models. The

LN-15 has an internal contactor and the electrode is

not energized until the gun trigger is closed. When the

gun trigger is closed the wire will begin to feed and the

welding process is started.

• Shut the welder off.

• For electrode Positive, connect the electrode cable to

the "+" terminal of the welder and work cable to the "-

" terminal of the welder. For electrode Negative, con-

nect the electrode cable "-" terminal of the welder

and work cable to the "+" terminal of the welder.

WARNING

TOTAL COMBINED LENGTH OF

ELECTRODE AND WORK CABLES

Cable Length

0-30meters (0-100Ft.)

30-46m meters (100-150 Ft.)

46-61 meters (150-200 Ft.)

Cable Size for

305 Amps

100% Duty Cycle

1 / 0 AWG

2 / 0 AWG

3 / 0 AWG

CAUTION

7. Set the "IDLE" switch to the "AUTO" position.

When not welding, the RANGER 305D (CE)

engine will be at the low idle speed. If you are

using an LN-25 with an internal contactor, the

electrode is not energized until the gun trigger is

closed.

8. When the gun trigger is closed, the current sens-

ing circuit will cause the RANGER 305D (CE)

engine to go to the high idle speed, the wire will

begin to feed and the welding process started.

When welding is stopped, the engine will revert to

low idle speed after approximately 12 seconds

unless welding is resumed.

If you are using an LN-25 without an internal con-

tactor, the electrode will be energized when the

RANGER 305D (CE) is started.

-----------------------------------------------------------------------

Connection of LN-742 and Cobramatic to

RANGER 305D (CE)

• Shut the welder off.

• Connect per instructions on the appropriate connec-

tion diagram in Section F.

Connection of PRINCE XL SPOOL GUN to the

RANGER 305D (CE)

Connection of the Prince XL Spool Gun requires the

use of the K1849-1 Adapter Module.

• Shut the Welder off.

• For electrode Positive, connect the electrode cable

to the "+" terminal of the welder and work cable to

the "-" terminal of the welder. For electrode

Negative, connect the electrode cable "-" terminal

of the welder and work cable to the "+" terminal of

the welder.

• Connect the Control Cable of the Spool Gun to the

Adapter Module and connect the Control Cable of

the Adapter Module to the Welder.

• Connect the Gas Hose.

• Set the MODE switch to the "CV-WIRE " position.

• Set the "WELD TERMINALS" switch to "WELD

TERMINALS ON".

• Set the "ARC CONTROL" knob to "0" initially and

adjust to suit.

• Set the “IDLE” switch to the “HIGH” position.

A-6

INSTALLATION

RANGER 305D (CE)

A-6

• Across-The-Arc Model:

Attach the single lead from the front of the LN-15 to

work using the spring clip at the end of the lead. This

is a control lead to supply current to the wire feeder

motor; it does not carry welding current.

Set the "WELD TERMINALS" switch to "WELD TER-

MINALS ON".

• Control Cable Model:

Connect Control Cable between Engine Welder and

Feeder.

Set the MODE switch to the "CV-WIRE " position.

Set the "WELD TERMINALS" switch to "REMOTELY

CONTROLLED".

Set the "WIRE FEEDER VOLTMETER" switch to

either "+" or "-" as required by the electrode polarity

being used.

Set the "ARC CONTROL" knob to "0" initially and

adjust to suit.

Set the "IDLE" switch to the "High" position.

Connection of the LN-25 to the RANGER 305D (CE)

Shut off welder before making any electrical con-

nections.

------------------------------------------------------------------------

The LN-25 with or without an internal contactor may be

used with the RANGER 305D (CE). See the appropri-

ate connection diagram in Section F.

NOTE: The LN-25 (K431) Remote Control Module and

(K432) Remote Cable are not recommended for use

with the RANGER 305D (CE).

1. Shut the welder off.

2. For electrode Positive, connect the electrode cable

from the LN-25 to the "+" terminal of the welder

and work cable to the "-" terminal of the welder. For

electrode Negative, connect the electrode cable

from the LN-25 to the "-" terminal of the welder and

work cable to the "+" terminal of the welder.

3. Attach the single lead from the front of the LN-25 to

work using the spring clip at the end of the lead.

This is a control lead to supply current to the wire

feeder motor; it does not carry welding current.

4. Set the MODE switch to the "CV-WIRE " position.

5. Set the "WELD TERMINALS" switch to "WELD

TERMINALS ON"

6. Set the "ARC CONTROL" knob to "0" initially and

adjust to suit.

WARNING

CAUTION

B-1

OPERATION

RANGER 305D (CE)

B-1

SAFETY PRECAUTIONS

Do not attempt to use this equipment until you

have thoroughly read the engine manufacturer’s

manual supplied with your welder. It includes

important safety precautions, detailed engine

starting, operating and maintenance instructions,

and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or

electrode with skin or wet clothing.

• Insulate yourself from work and

ground

• Always wear dry insulating gloves.

• Always operate the welder with the hinged door

closed and the side panels in place.

• Read carefully the Safety Precautions page

before operating this machine. Always follow

these and any other safety procedures included

in this manual and in the Engine Instruction

Manual.

GENERAL DESCRIPTION

The RANGER 305D (CE) is a diesel engine powered

DC multi-process welding power source and AC

power generator. The engine drives a generator that

supplies three phase power for the DC welding circuit

and three phase and single phase power for the AC

auxiliary outlets. The DC welding control system uses

state of the art Chopper Technology (CT

) for supe-

rior welding performance.

FOR AUXILIARY POWER:

Start the engine and set the IDLER control switch to

the desired operating mode. Full power is available

regardless of the welding control settings providing no

welding current is being drawn.

ENGINE OPERATION

Before Starting the Engine:

• Be sure the machine is on a level surface.

• Open top & side engine doors and remove the

engine oil dipstick and wipe it with a clean cloth.

Reinsert the dipstick and check the level on the dip-

stick.

• Add oil (if necessary) to bring the level up to the full

mark. Do not overfill. Close engine door.

• Check radiator for proper coolant level. (Fill if nec-

essary).

• See Engine Owner’s Manual for specific oil and

coolant recommendations.

ADD FUEL

FUEL can cause fire or

explosion.

• Stop engine when fueling.

• Do not smoke when fueling.

• Do not overfill tank.

• Avoid contact with skin or breathing of vapor.

• Keep sparks and flame away from tank.

------------------------------------------------------------------------

• Remove the fuel tank cap.

• Fill the tank approximately 4 inches (100mm) from

the top of the filler neck to allow for fuel expansion

(observe the fuel gauge while filling). DO NOT FILL

THE TANK TO THE POINT OF OVERFLOW.

• Replace the fuel cap and tighten securely.

• See Engine Owner’s Manual for specific fuel recom-

mendations.

BREAK-IN PERIOD

Any engine will use a small amount of oil during its

“break-in” period. For the diesel engine on the

RANGER 305D (CE), break-in is about 50 running

hours.

Check the oil every four hours during break-in.

Change the oil after the first 50 hours of operation,

every 100 hours thereafter. Change the oil filter at the

second oil change.

During break-in, subject the RANGER 305D (CE)

to moderate loads. Avoid long periods running at

idle. Before stopping the engine, remove all loads

and allow the engine to cool several minutes.

------------------------------------------------------------------------

WARNING

CAUTION

B-2

OPERATION

B-2

WELDING CONTROLS (Figure B.1)

1. OUTPUT CONTROL:

The OUTPUT dial is

used to preset the output voltage or current as dis-

played on the digital meters for the four welding

modes. When in the CC-STICK, DOWNHILL PIPE

or CV-WIRE modes and when a remote control is

connected to the 6-Pin or 14-Pin Connector, the

auto-sensing circuit automatically switches the

OUTPUT CONTROL from control at the welder to

the remote control.

In the CV-WIRE mode, if the wire feeder has volt-

age control capability, when the control cable is

connected to the 14-Pin Connector, the auto-sens-

ing circuit automatically makes OUTPUT CON-

TROL inactive and the wire feeder voltage control

active.

When in the TOUCH START TIG mode and when

a Amptrol is connected to the 6-Pin Connector, the

OUTPUT control is used to set the maximum cur-

rent range of the CURRENT CONTROL of the

Amptrol.

2. DIGITAL OUTPUT METERS

The digital meters allow the output voltage (CV-

WIRE mode) or current (CC-STICK, PIPE and TIG

modes) to be set prior to welding using the OUT-

PUT control dial. During welding, the meter display

the actual output voltage (VOLTS) and current

(AMPS). A memory feature holds the display of

both meters on for seven seconds after welding is

stopped. This allows the operator to read the actu-

al current and voltage just prior to when welding

was ceased.

While the display is being held the left-most deci-

mal point in each display will be flashing. The

accuracy of the meters is +/- 3%.

3. WELD MODE SELECTOR SWITCH:

(Provides four selectable welding modes)

CV-WIRE

DOWNHILL PIPE

CC-STICK

TOUCH START TIG

RANGER 305D (CE)

FIGURE B.1

La page charge ...

Lincoln Electric Ranger 305D Mode d'emploi

Marque: Lincoln Electric

Modèle: Ranger 305D

Catégorie: Système de soudage

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric Ranger 305D Operating instructions

Lincoln Electric Ranger 305D Mode d'emploi

Lincoln Electric Ranger 305D Mode d'emploi

dans d''autres langues

Documents connexes