AEG HK604200IB Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
EN User Manual 2
Hob
FR Notice d'utilisation 17
Table de cuisson
DE Benutzerinformation 34
Kochfeld
HK604200IB
CONTENTS
1. SAFETY INFORMATION...........................................................................................3
2. SAFETY INSTRUCTIONS.......................................................................................... 4
3. PRODUCT DESCRIPTION........................................................................................ 6
4. DAILY USE..................................................................................................................7
5. HINTS AND TIPS....................................................................................................... 9
6. CARE AND CLEANING.......................................................................................... 10
7. TROUBLESHOOTING.............................................................................................10
8. INSTALLATION....................................................................................................... 12
9. TECHNICAL INFORMATION.................................................................................15
10. ENERGY EFFICIENCY.......................................................................................... 15
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
www.aeg.com
2
1. SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible if an incorrect
installation and use causes injuries and damages. Always
keep the instructions with the appliance for future
reference.
1.1 Children and vulnerable people safety
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Do not let children play with the appliance.
Keep all packaging away from children.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts are
hot.
If the appliance has a child safety device, we
recommend you activate it.
Cleaning and user maintenance shall not be made by
children without supervision.
Children of less than 3 years should be kept away
unless continuously supervised.
1.2
General Safety
The appliance and its accessible parts become hot
during use. Do not touch the heating elements.
Do not operate the appliance by means of an external
timer or separate remote-control system.
Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
Never try to extinguish a fire with water, but switch off
the appliance and then cover flame e.g. with a lid or a
fire blanket.
ENGLISH
3
Do not store items on the cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use a steam cleaner to clean the appliance.
After use, switch off the hob element by its control
and do not rely on the pan detector.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance to avoid the possibility of
electric shock.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
Remove all the packaging.
Do not install or use a damaged
appliance.
Obey the installation instruction
supplied with the appliance.
Keep the minimum distance from the
other appliances and units.
Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware to fall from the
appliance when the door or the
window is opened.
If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
The bottom of the appliance can get
hot. Make sure to install a non-
combustile separation panel under
the appliance to prevent access to the
bottom.
Make sure that the ventilation space
of 2 mm, between the worktop and
the front of the below unit, is free.
The warranty does not cover damages
caused by the lack of an adequate
ventilation space.
2.2 Electrical Connection
WARNING!
Risk of fire and electrical
shock.
All electrical connections should be
made by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
Make sure that the electrical
information on the rating plate agrees
with the power supply. If not, contact
an electrician.
Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
Use the correct electricity mains
cable.
Do not let the electricity mains cable
tangle.
www.aeg.com
4
Make sure that a shock protection is
installed.
Use the strain relief clamp on the
cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact an Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.3 Use
WARNING!
Risk of injury, burns and
electrical shock.
Remove all the packaging, labelling
and protective film (if applicable)
before first use.
Use this appliance in a household
environment.
Do not change the specification of
this appliance.
Make sure that the ventilation
openings are not blocked.
Do not let the appliance stay
unattended during operation.
Set the cooking zone to “off” after
each use.
Do not rely on the pan detector.
Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
Do not operate the appliance with
wet hands or when it has contact with
water.
Do not use the appliance as a work
surface or as a storage surface.
If the surface of the appliance is
cracked, disconnect immediately the
appliance from the power supply. This
to prevent an electrical shock.
Users with a pacemaker must keep a
distance of minimum 30 cm from the
induction cooking zones when the
appliance is in operation.
When you place food into hot oil, it
may splash.
WARNING!
Risk of fire and explosion
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
WARNING!
Risk of damage to the
appliance.
Do not keep hot cookware on the
control panel.
Do not let cookware to boil dry.
Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
Do not activate the cooking zones
with empty cookware or without
cookware.
Do not put aluminium foil on the
appliance.
ENGLISH
5
Cookware made of cast iron,
aluminium or with a damaged bottom
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
2.4 Care and cleaning
Clean regularly the appliance to
prevent the deterioration of the
surface material.
Deactivate the appliance and let it
cool down before you clean it.
Disconnect the appliance from the
electrical supply before maintenance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
2.5 Disposal
WARNING!
Risk of injury or suffocation.
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the
mains supply.
Cut off the mains cable and discard it.
3. PRODUCT DESCRIPTION
3.1 Cooking surface layout
210 mm
145 mm
180 mm
145 mm
1
1
1 1
2
1
Induction cooking zone
2
Control panel
3.2 Control panel layout
1 32 4 5
Use the sensor fields to operate the appliance. The displays, indicators and sounds tell
which functions operate.
Sensor
field
Function Comment
1
ON / OFF To activate and deactivate the hob.
www.aeg.com6
Sensor
field
Function Comment
2
Lock / The Child Safety De-
vice
To lock / unlock the control panel.
3
- To select the cooking zone.
4
- Heat setting display To show the heat setting.
5
/
- To set a heat setting.
3.3 Heat setting displays
Display Description
The cooking zone is deactivated.
-
The cooking zone operates.
Power function operates.
+ digit
There is a malfunction.
A cooking zone is still hot (residual heat).
Lock / The Child Safety Device function operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off function operates.
3.4 Residual heat indicator
WARNING!
There is a risk of burns
from residual heat.
The induction cooking zones make the
heat necessary for cooking process
directly in the bottom of the cookware.
The glass ceramic is heated by the heat
of the cookware.
4. DAILY USE
WARNING!
Refer to Safety chapters.
4.1 Activating and
deactivating
Touch for 1 second to activate or
deactivate the hob.
4.2 Automatic Switch Off
The function deactivates the hob
automatically if:
all cooking zones are deactivated,
you do not set the heat setting after
you activate the hob,
you spill something or put something
on the control panel for more than 10
seconds (a pan, a cloth, etc.). An
ENGLISH 7
acoustic signal sounds and the hob
deactivates. Remove the object or
clean the control panel.
the hob gets too hot (e.g. when a
saucepan boils dry). Let the cooking
zone cool down before you use the
hob again.
you use incorrect cookware. The
symbol comes on and the cooking
zone deactivates automatically after 2
minutes.
you do not deactivate a cooking zone
or change the heat setting. After
some time comes on and the hob
deactivates.
The relation between the heat setting
and the time after which the hob
deactivates:
Heat setting The hob deacti-
vates after
1 - 2 6 hours
3 - 4 5 hours
5 4 hours
6 - 9 1.5 hour
4.3 Selecting the cooking zone
To set the cooking zone touch the sensor
field
related to this zone. The display
highlights the heat setting indication
( ).
4.4 The heat setting
Set the cooking zone.
Touch
to increase the heat setting.
Touch to decrease the heat setting.
Touch
and at the same time to
deactivate the cooking zone.
4.5 Power function
This function makes more power
available to the induction cooking zones.
The function can be activated for the
induction cooking zone only for a limited
period of time. After this time the
induction cooking zone automatically
sets back to the highest heat setting.
Refer to “Technical
information” chapter.
To activate the function for a cooking
zone: first set the cooking zone and than
set the maximum heat setting. Touch
until comes on.
To deactivate the function: touch .
4.6 Lock
You can lock the control panel while
cooking zones operate. It prevents an
accidental change of the heat setting.
Set the heat setting first.
To activate the function: touch
.
comes on for 4 seconds.
To deactivate the function: touch .
The previous heat setting comes on.
When you deactivate the
hob, you also deactivate this
function.
4.7 The Child Safety Device
This function prevents an accidental
operation of the hob.
To activate the function: activate the
hob with
. Do not set the heat setting.
Touch for 4 seconds. comes on.
Deactivate the hob with
.
To deactivate the function: activate the
hob with . Do not set the heat setting.
Touch for 4 seconds. comes on.
Deactivate the hob with
.
To override the function for only one
cooking time: activate the hob with .
comes on. Touch for 4 seconds.
Set the heat setting in 10 seconds. You
can operate the hob. When you
deactivate the hob with
the function
operates again.
www.aeg.com
8
5. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
5.1 Cookware
For induction cooking zones
a strong electro-magnetic
field creates the heat in the
cookware very quickly.
Use the induction cooking
zones with correct cookware.
Cookware material
correct: cast iron, steel, enamelled
steel, stainless steel, the bottom
made of multi-layer (with correct mark
from a manufacturer).
not correct: aluminium, copper,
brass, glass, ceramic, porcelain.
Cookware is correct for an induction
hob if:
some water boils very quickly on a
zone set to the highest heat setting.
a magnet pulls on to the bottom of
the cookware.
The bottom of the cookware
must be as thick and flat as
possible.
Cookware dimensions
Induction cooking zones adapt to the
dimension of the bottom of the
cookware automatically to some limit.
The cooking zone efficiency is related to
the diameter of the cookware. The
cookware with a smaller diameter than
the minimum receives only a part of the
power generated by the cooking zone.
Refer to “Technical
information” chapter.
5.2 The noises during
operation
If you can hear:
crack noise: cookware is made of
different materials (sandwich
construction).
whistle sound: you the cooking zone
with high power level and the
cookware is made of different
materials (sandwich construction).
humming: you use high power level.
clicking: electric switching occurs.
hissing, buzzing: the fan operates.
The noises are normal and do not refer
to hob malfunction.
5.3 Examples of cooking
applications
The relation between the heat setting
and the cooking zone consumption of
power is not linear. When you increase
the heat setting, it is not proportional to
the increase of the cooking zone
consumption of power. It means that the
cooking zone with the medium heat
setting uses less than a half of its power.
The data in the table is for
guidance only.
Heat setting Use to: Time
(min)
Hints
1 Keep cooked food warm. as nec-
essary
Put a lid on the cookware.
1 - 2 Hollandaise sauce, melt: but-
ter, chocolate, gelatine.
5 - 25 Mix from time to time.
1 - 2 Solidify: fluffy omelettes,
baked eggs.
10 - 40 Cook with a lid on.
ENGLISH 9
Heat setting Use to: Time
(min)
Hints
2 - 3 Simmer rice and milkbased
dishes, heating up ready-
cooked meals.
25 - 50 Add the minimum twice as
much liquid as rice, mix milk
dishes part procedure
through.
3 - 4 Steam vegetables, fish, meat. 20 - 45 Add some tablespoons of liq-
uid.
4 - 5 Steam potatoes. 20 - 60 Use max. ¼ l water for 750 g of
potatoes.
4 - 5 Cook larger quantities of food,
stews and soups.
60 - 150 Up to 3 l liquid plus ingredi-
ents.
6 - 7 Gentle fry: escalope, veal cor-
don bleu, cutlets, rissoles,
sausages, liver, roux, eggs,
pancakes, doughnuts.
as nec-
essary
Turn halfway through.
7 - 8 Heavy fry, hash browns, loin
steaks, steaks.
5 - 15 Turn halfway through.
9 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. Power function is activated.
6. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
6.1 General information
Clean the hob after each use.
Always use cookware with clean
bottom.
Scratches or dark stains on the surface
have no effect on how the hob
operates.
Use a special cleaner applicable for
the surface of the hob.
Use a special scraper for the glass.
6.2 Cleaning the hob
Remove immediately: melted plastic,
plastic foil, and food with sugar. If not,
the dirt can cause damage to the hob.
Put the special scraper on the glass
surface at an acute angle and move
the blade on the surface.
Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
some detergent. After cleaning, rub
the hob dry with a soft cloth.
7. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
www.aeg.com10
7.1 What to do if...
Problem Possible cause Remedy
You cannot activate or oper-
ate the hob.
The hob is not connected to
an electrical supply or it is
connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram.
The fuse is released. Make sure that the fuse is
the cause of the malfunction.
If the fuse releases again
and again, contact a quali-
fied electrician.
Activate the hob again and
set the heat setting in less
than 10 seconds.
You touched 2 or more sen-
sor fields at the same time.
Touch only one sensor field.
There is water or fat stains
on the control panel.
Clean the control panel.
An acoustic signal sounds
and the hob deactivates.
An acoustic signal sounds
when the hob is deactivated.
You put something on one
or more sensor fields.
Remove the object from the
sensor fields.
The hob deactivates. You put something on the
sensor field .
Remove the object from the
sensor field.
Residual heat indicator does
not come on.
The zone is not hot because
it operated only for a short
time.
If the zone operated suffi-
ciently long to be hot, speak
to an Authorised Service
Centre.
The sensor fields become
hot.
The cookware is too large or
you put it too near to the
controls.
Put large cookware on the
rear zones if possible.
comes on.
Automatic Switch Off oper-
ates.
Deactivate the hob and acti-
vate it again.
comes on.
The Child Safety Device or
the Lock function operates.
Refer to "Daily use" chapter.
comes on.
There is no cookware on the
zone.
Put cookware on the zone.
The cookware is incorrect. Use the correct cookware.
Refer to “Hints and tips”
chapter.
ENGLISH 11
Problem Possible cause Remedy
The diameter of the bottom
of the cookware is too small
for the zone.
Use cookware with correct
dimensions.
Refer to “Technical informa-
tion” chapter.
and a number come on.
There is an error in the hob. Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If comes on again, speak
to an Authorised Service
Centre.
comes on.
There is an error in the hob
because a cookware boils
dry. Automatic Switch Off
and the overheating protec-
tion for the zones operate.
Deactivate the hob. Remove
the hot cookware. After ap-
proximately 30 seconds, acti-
vate the zone again. If the
cookware was the problem,
the error message goes out.
Residual heat indicator can
stay on. Let the cookware
become sufficiently cool.
Check if your cookware is
compatible with the hob.
Refer to “Hints and tips”
chapter.
7.2 If you cannot find a
solution...
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Give also
three digit letter code for the glass
ceramic (it is in the corner of the glass
surface) and an error message that
comes on. Make sure, you operated the
hob correctly. If not the servicing by a
service technician or dealer will not be
free of charge, also during the warranty
period. The instructions about the
Service Centre and conditions of
guarantee are in the guarantee booklet.
8. INSTALLATION
WARNING!
Refer to Safety chapters.
8.1 Before the installation
Before you install the hob, write down
the information bellow from the rating
plate. The rating plate is on the bottom
of the hob.
Serial number ...........................
8.2 Built-in hobs
Only use the built-in hobs after you
assemble the hob into correct built-in
units and work surfaces that align to the
standards.
8.3 Connection cable
The hob is supplied with a connection
cable.
www.aeg.com12
To replace the damaged mains cable
use the following (or higher) mains
cable type: H05BB-F Tmax 90°C.
Speak to your local Service Centre.
8.4 Attaching the seal
1. Clean the worktop around the cut
out area.
2. Attach the supplied seal stripe to the
lower edge of the hob along the
outer edge of the glass ceramic. Do
not extend it. Make sure that the
ends of the seal stripe are located in
the middle of one side of the hob.
3. Add some mm when you cut the seal
stripe to the length.
4. Push the two ends of seal stripe
together.
8.5 Assembly
min.
50mm
min.
500mm
min.
2mm
min. 2 mm
A
B
A
12 mm
28 mm
38 mm
B
57 mm
41 mm
31 mm
min
30 mm
min. 500 mm
< 20 mm
> 20 mm
min. 2 mm
A
B
A
12 mm
28 mm
38 mm
B
57 mm
41 mm
31 mm
min. 500 mm
ENGLISH 13
R 5mm
min.
55mm
560
+1
mm
490
+1
mm
min.
38 mm
min.
2 mm
min.
12 mm
min.
2 mm
8.6 Protection box
If you use a protection box (an additional
accessory), the front airflow space of 2
mm and the protective floor directly
below the hob are not necessary. The
protection box accessory may not be
available in some countries. Please
contact your local supplier.
You can not use the
protection box if you install
the hob above an oven.
www.aeg.com14
9. TECHNICAL INFORMATION
9.1 Rating plate
Modell HK604200IB PNC 949 492 085 00
Typ 58 GAP D5 AU 220 - 240 V 50 - 60 Hz
Induction 3.0 kW Made in Romania
Ser.Nr. ................. 3.0 kW
AEG
9.2 Cooking zones specification
Cooking zone Nominal power
(maximum heat
setting) [W]
Power function
[W]
Power function
maximum dura-
tion [min]
Cookware diam-
eter [mm]
Left front 2300 2800 10 180 - 210
Left rear 1200 - - 125 - 145
Right front 1200 1800 4 125 - 145
Right rear 1800 - - 145 - 180
The power of the cooking zones can be
different in some small range from the
data in the table. It changes with the
material and dimensions of the
cookware.
For optimal cooking results use
cookware not larger than the diameter in
the table.
10. ENERGY EFFICIENCY
10.1 Product information according to EU 66/2014
Model identification HK604200IB
Type of hob Built-In Hob
Number of cooking zones 4
Heating technology Induction
Diameter of circular cooking zones (Ø) Left front
Left rear
Right front
Right rear
21.0 cm
14.5 cm
14.5 cm
18.0 cm
Energy consumption per cooking zone (ECelec-
tric cooking)
Left front
Left rear
Right front
Right rear
168.0 Wh / kg
195.0 Wh / kg
182.0 Wh / kg
198.0 Wh / kg
Energy consumption of the hob (ECelectric hob) 185.8 Wh / kg
ENGLISH 15
EN 60350-2 - Household electric cooking
appliances - Part 2: Hobs - Methods for
measuring performance
10.2 Energy saving
You can save energy during everyday
cooking if you follow bellow hints.
Put the cookware on the cooking
zone before you activate it.
Put smaller cookware on smaller
cooking zones.
Put the cookware directly in the
centre of the cooking zone.
When you heat up water use only the
amount you need.
If it is possible, put the lids on the
cookware.
Use the residual heat to keep the
food warm or to melt it.
11. ENVIRONMENT CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to
recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
www.aeg.com16
TABLE DES MATIÈRES
1. CONSIGNES DE SÉCURITÉ................................................................................... 18
2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 19
3. DESCRIPTION DE L'APPAREIL.............................................................................. 22
4. UTILISATION QUOTIDIENNE................................................................................23
5. CONSEILS................................................................................................................25
6. ENTRETIEN ET NETTOYAGE................................................................................ 26
7. EN CAS D'ANOMALIE DE FONCTIONNEMENT................................................27
8. INSTALLATION....................................................................................................... 29
9. CARACTÉRISTIQUES TECHNIQUES.....................................................................32
10. RENDEMENT ÉNERGÉTIQUE.............................................................................32
POUR DES RÉSULTATS PARFAITS
Merci d'avoir choisi ce produit AEG. Nous l'avons conçu pour qu'il vous offre des
performances irréprochables pour longtemps, en intégrant des technologies
innovantes qui vous simplifient la vie grâce à des caractéristiques que vous ne
trouverez pas forcément sur des appareils ordinaires. Veuillez prendre quelques
instants pour lire cette notice afin d'utiliser au mieux votre appareil.
Visitez notre site Internet pour :
Obtenir des conseils d'utilisation, des brochures, de l'aide, des informations :
www.aeg.com
Enregistrer votre produit pour obtenir un meilleur service :
www.registeraeg.com
Acheter des accessoires, consommables et pièces de rechange d'origine pour
votre appareil :
www.aeg.com/shop
SERVICE APRÈS-VENTE
N'utilisez que des pièces de rechange d'origine.
Avant de contacter le service, assurez-vous de disposer des informations
suivantes : Modèle, PNC, numéro de série.
Vous trouverez ces informations sur la plaque signalétique.
Avertissement/Attention : consignes de sécurité.
Informations générales et conseils.
Informations en matière de protection de l'environnement.
Sous réserve de modifications.
FRANÇAIS
17
1. CONSIGNES DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez
soigneusement les instructions fournies. Le fabricant ne
peut être tenu pour responsable des dommages et
blessures liés à une mauvaise installation ou utilisation.
Conservez toujours cette notice avec votre appareil
pour vous y référer ultérieurement.
1.1 Sécurité des enfants et des personnes
vulnérables
Cet appareil peut être utilisé par des enfants âgés
d'au moins 8 ans et par des personnes ayant des
capacités physiques, sensorielles ou mentales réduites
ou dénuées d’expérience ou de connaissance, s’ils (si
elles) sont correctement surveillé(e)s ou si des
instructions relatives à l’utilisation de l'appareil en
toute sécurité leur ont été données et si les risques
encourus ont été appréhendées.
Les enfants ne doivent pas jouer avec l’appareil.
Ne laissez pas les emballages à la portée des enfants.
Tenez les enfants et les animaux éloignés de l'appareil
lorsqu'il est en cours de fonctionnement ou lorsqu'il
refroidit. Les parties accessibles sont chaudes.
Si l'appareil est équipé d'un dispositif de sécurité
enfants, nous vous recommandons de l'activer.
Le nettoyage et l’entretien par l'usager ne doivent pas
être effectués par des enfants sans surveillance.
Les enfants de moins de 3 ans, sans surveillance,
doivent être tenus à l'écart de l'appareil.
1.2
Sécurité générale
L'appareil et ses parties accessibles deviennent
chauds pendant son fonctionnement. Ne touchez pas
les résistances.
Ne faites pas fonctionner l'appareil avec un minuteur
externe ou un système de commande à distance.
www.aeg.com
18
Il peut être dangereux de laisser chauffer de la graisse
ou de l'huile sans surveillance sur une table de cuisson
car cela pourrait provoquer un incendie.
N'essayez jamais d'éteindre un feu avec de l'eau.
Éteignez l'appareil puis couvrez les flammes, par
exemple avec un couvercle ou une couverture
ignifuge.
N'entreposez rien sur les surfaces de cuisson.
Ne posez pas d'objets métalliques tels que couteaux,
fourchettes, cuillères ou couvercles sur la table de
cuisson car ils pourraient chauffer.
N'utilisez pas de nettoyeur vapeur pour nettoyer
l'appareil.
Après utilisation, éteignez toujours la zone de cuisson
à l'aide de la manette de commande correspondante
et ne vous fiez pas à la détection des récipients.
Si la surface vitrocéramique est fissurée, éteignez
l'appareil pour éviter tout risque d'électrocution.
Si le câble d'alimentation est endommagé, il doit être
remplacé par le fabricant, un service de maintenance
agréé ou un technicien qualifié afin d'éviter tout
danger.
2.
INSTRUCTIONS DE SÉCURITÉ
2.1 Instructions d’installation
AVERTISSEMENT!
L'appareil doit être installé
uniquement par un
professionnel qualifié.
Retirez l'intégralité de l'emballage
N'installez pas et ne branchez pas un
appareil endommagé.
Suivez scrupuleusement les
instructions d'installation fournies
avec l'appareil.
Respectez l'espacement minimal
requis par rapport aux autres
appareils et éléments.
Soyez toujours vigilants lorsque vous
déplacez l'appareil car il est lourd.
Portez toujours des gants de sécurité.
Isolez les surfaces découpées à l'aide
d'un matériau d'étanchéité pour
éviter que la moisissure ne provoque
des gonflements.
Protégez la partie inférieure de
l'appareil de la vapeur et de
l'humidité.
N'installez pas l'appareil près d'une
porte ou sous une fenêtre. Les
récipients chauds risqueraient de
tomber de l'appareil lors de
l'ouverture de celles-ci.
Si l'appareil est installé au-dessus de
tiroirs, assurez-vous qu'il y a
suffisamment d'espace entre le fond
de l'appareil et le tiroir supérieur pour
que l'air puisse circuler.
Le dessous de l'appareil peut devenir
très chaud. Veillez à installer un
FRANÇAIS
19
panneau de séparation ignifuge sous
l'appareil pour en bloquer l'accès.
Assurez-vous de laisser un espace de
ventilation de 2 mm entre le plan de
travail et l'avant de l'unité qui se
trouve dessous. La garantie ne couvre
pas les dommages causés par
l'absence d'un espace de ventilation
adéquat.
2.2 Branchement électrique
AVERTISSEMENT!
Risque d'incendie ou
d'électrocution.
L'ensemble des branchements
électriques doit être effectué par un
technicien qualifié.
L'appareil doit être relié à la terre.
Avant toute intervention, assurez-vous
que l'appareil est débranché.
Vérifiez que les données électriques
figurant sur la plaque signalétique
correspondent à celles de votre
réseau. Si ce n'est pas le cas,
contactez un électricien.
Assurez-vous que l'appareil est bien
installé. Un câble d'alimentation lâche
et inapproprié ou une fiche (si
présente) non serrée peuvent être à
l'origine d'une surchauffe des bornes.
Utilisez le câble d'alimentation
électrique approprié.
Ne laissez pas le câble d'alimentation
s'emmêler.
Assurez-vous qu'une protection anti-
électrocution est installée.
Utilisez un collier anti-traction sur le
câble.
Assurez-vous que le câble
d'alimentation ou la fiche (si présente)
n'entrent pas en contact avec les
surfaces brûlantes de l'appareil ou les
récipients brûlants lorsque vous
branchez l'appareil à des prises
électriques situées à proximité.
N'utilisez pas d'adaptateurs
multiprises ni de rallonges.
Veillez à ne pas endommager la fiche
secteur (si présente) ni le câble
d'alimentation. Contactez un service
après-vente agréé ou un électricien
pour remplacer le câble
d'alimentation s'il est endommagé.
La protection contre les chocs des
parties sous tension et isolées doit
être fixée de telle manière qu'elle ne
puisse pas être enlevée sans outils.
Ne connectez la fiche d'alimentation
secteur à la prise de courant secteur
qu'à la fin de l'installation. Assurez-
vous que la fiche d'alimentation est
accessible une fois l'appareil installé.
Si la prise de courant est lâche, ne
branchez pas la fiche d'alimentation
secteur.
Ne tirez jamais sur le câble
d'alimentation électrique pour
débrancher l'appareil. Tirez toujours
sur la fiche.
N'utilisez que des systèmes
d'isolation appropriés : des coupe-
circuits, des fusibles (les fusibles à
visser doivent être retirés du support),
des disjoncteurs différentiels et des
contacteurs.
L'installation électrique doit être
équipée d'un dispositif d'isolement à
coupure omnipolaire. Le dispositif
d'isolement doit présenter une
distance d'ouverture des contacts
d'au moins 3 mm.
2.3 Utilisation
AVERTISSEMENT!
Risque de blessures, de
brûlures ou d'électrocution.
Avant la première utilisation, retirez
les emballages, les étiquettes et les
films de protection (si présents).
Utilisez cet appareil dans un
environnement domestique.
Ne modifiez pas les caractéristiques
de cet appareil.
Assurez-vous que les orifices de
ventilation ne sont pas bouchés.
Ne laissez jamais l'appareil sans
surveillance pendant son
fonctionnement.
Éteignez les zones de cuisson après
chaque utilisation.
Ne vous fiez pas uniquement au
détecteur de récipient.
Ne posez pas de couverts ou de
couvercles sur les zones de cuisson.
Elles sont chaudes.
www.aeg.com
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

AEG HK604200IB Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur

dans d''autres langues